/** ****************************************************************************** * @file stm32f0xx.h * @author MCD Application Team * @version V1.0.0 * @date 23-March-2012 * @brief CMSIS Cortex-M0 Device Peripheral Access Layer Header File. * This file contains all the peripheral register's definitions, bits * definitions and memory mapping for STM32F0xx devices. * * The file is the unique include file that the application programmer * is using in the C source code, usually in main.c. This file contains: * - Configuration section that allows to select: * - The device used in the target application * - To use or not the peripheral’s drivers in application code(i.e. * code will be based on direct access to peripheral’s registers * rather than drivers API), this option is controlled by * "#define USE_STDPERIPH_DRIVER" * - To change few application-specific parameters such as the HSE * crystal frequency * - Data structures and the address mapping for all peripherals * - Peripheral's registers declarations and bits definition * - Macros to access peripheral’s registers hardware * ****************************************************************************** * @attention * *

© COPYRIGHT 2012 STMicroelectronics

* * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); * You may not use this file except in compliance with the License. * You may obtain a copy of the License at: * * http://www.st.com/software_license_agreement_liberty_v2 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * ****************************************************************************** */ /** @addtogroup CMSIS * @{ */ /** @addtogroup stm32f0xx * @{ */ #ifndef __STM32F0XX_H #define __STM32F0XX_H #ifdef __cplusplus extern "C" { #endif /** @addtogroup Library_configuration_section * @{ */ /* Uncomment the line below according to the target STM32F-0 device used in your application */ #if !defined (STM32F0XX) #define STM32F0XX /*!< STM32F0XX: STM32F0xx devices */ #endif /* Tip: To avoid modifying this file each time you need to switch between these devices, you can define the device in your toolchain compiler preprocessor. - STM32F0xx devices are STM32F050xx microcontrollers where the Flash memory density ranges between 32 and 64 Kbytes. */ #if !defined (STM32F0XX) #error "Please select first the target STM32F0xx device used in your application (in stm32f0xx.h file)" #endif /* STM32F0XX */ #if !defined USE_STDPERIPH_DRIVER /** * @brief Comment the line below if you will not use the peripherals drivers. In this case, these drivers will not be included and the application code will be based on direct access to peripherals registers */ /*#define USE_STDPERIPH_DRIVER*/ #endif /* USE_STDPERIPH_DRIVER */ /** * @brief In the following line adjust the value of External High Speed oscillator (HSE) used in your application Tip: To avoid modifying this file each time you need to use different HSE, you can define the HSE value in your toolchain compiler preprocessor. */ #if !defined (HSE_VALUE) #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz*/ #endif /* HSE_VALUE */ /** * @brief In the following line adjust the External High Speed oscillator (HSE) Startup Timeout value */ #if !defined (HSE_STARTUP_TIMEOUT) #define HSE_STARTUP_TIMEOUT ((uint16_t)0x0500) /*!< Time out for HSE start up */ #endif /* HSE_STARTUP_TIMEOUT */ /** * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup Timeout value */ #if !defined (HSI_STARTUP_TIMEOUT) #define HSI_STARTUP_TIMEOUT ((uint16_t)0x0500) /*!< Time out for HSI start up */ #endif /* HSI_STARTUP_TIMEOUT */ #if !defined (HSI_VALUE) #define HSI_VALUE ((uint32_t)8000000) /*!< Value of the Internal High Speed oscillator in Hz. The real value may vary depending on the variations in voltage and temperature. */ #endif /* HSI_VALUE */ #if !defined (HSI14_VALUE) #define HSI14_VALUE ((uint32_t)14000000) /*!< Value of the Internal High Speed oscillator for ADC in Hz. The real value may vary depending on the variations in voltage and temperature. */ #endif /* HSI14_VALUE */ #if !defined (LSI_VALUE) #define LSI_VALUE ((uint32_t)40000) /*!< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. */ #endif /* LSI_VALUE */ #if !defined (LSE_VALUE) #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ #endif /* LSE_VALUE */ /** * @brief STM32F0xx Standard Peripheral Library version number V1.0.0 */ #define __STM32F0XX_STDPERIPH_VERSION_MAIN (0x01) /*!< [31:24] main version */ #define __STM32F0XX_STDPERIPH_VERSION_SUB1 (0x00) /*!< [23:16] sub1 version */ #define __STM32F0XX_STDPERIPH_VERSION_SUB2 (0x00) /*!< [15:8] sub2 version */ #define __STM32F0XX_STDPERIPH_VERSION_RC (0x00) /*!< [7:0] release candidate */ #define __STM32F0XX_STDPERIPH_VERSION ((__STM32F0XX_STDPERIPH_VERSION_MAIN << 24)\ |(__STM32F0XX_STDPERIPH_VERSION_SUB1 << 16)\ |(__STM32F0XX_STDPERIPH_VERSION_SUB2 << 8)\ |(__STM32F0XX_STDPERIPH_VERSION_RC)) /** * @} */ /** @addtogroup Configuration_section_for_CMSIS * @{ */ /** * @brief STM32F0xx Interrupt Number Definition, according to the selected device * in @ref Library_configuration_section */ #define __CM0_REV 0 /*!< Core Revision r0p0 */ #define __MPU_PRESENT 0 /*!< STM32F0xx do not provide MPU */ #define __NVIC_PRIO_BITS 2 /*!< STM32F0xx uses 2 Bits for the Priority Levels */ #define __Vendor_SysTickConfig 0 /*!< Set to 1 if different SysTick Config is used */ /*!< Interrupt Number Definition */ typedef enum IRQn { /****** Cortex-M0 Processor Exceptions Numbers ******************************************************/ NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ HardFault_IRQn = -13, /*!< 3 Cortex-M0 Hard Fault Interrupt */ SVC_IRQn = -5, /*!< 11 Cortex-M0 SV Call Interrupt */ PendSV_IRQn = -2, /*!< 14 Cortex-M0 Pend SV Interrupt */ SysTick_IRQn = -1, /*!< 15 Cortex-M0 System Tick Interrupt */ /****** STM32F-0 specific Interrupt Numbers *********************************************************/ WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ PVD_IRQn = 1, /*!< PVD through EXTI Line detect Interrupt */ RTC_IRQn = 2, /*!< RTC through EXTI Line Interrupt */ FLASH_IRQn = 3, /*!< FLASH Interrupt */ RCC_IRQn = 4, /*!< RCC Interrupt */ EXTI0_1_IRQn = 5, /*!< EXTI Line 0 and 1 Interrupts */ EXTI2_3_IRQn = 6, /*!< EXTI Line 2 and 3 Interrupts */ EXTI4_15_IRQn = 7, /*!< EXTI Line 4 to 15 Interrupts */ TS_IRQn = 8, /*!< TS Interrupt */ DMA1_Channel1_IRQn = 9, /*!< DMA1 Channel 1 Interrupt */ DMA1_Channel2_3_IRQn = 10, /*!< DMA1 Channel 2 and Channel 3 Interrupts */ DMA1_Channel4_5_IRQn = 11, /*!< DMA1 Channel 4 and Channel 5 Interrupts */ ADC1_COMP_IRQn = 12, /*!< ADC1, COMP1 and COMP2 Interrupts */ TIM1_BRK_UP_TRG_COM_IRQn = 13, /*!< TIM1 Break, Update, Trigger and Commutation Interrupts */ TIM1_CC_IRQn = 14, /*!< TIM1 Capture Compare Interrupt */ TIM2_IRQn = 15, /*!< TIM2 Interrupt */ TIM3_IRQn = 16, /*!< TIM3 Interrupt */ TIM6_DAC_IRQn = 17, /*!< TIM6 and DAC Interrupts */ TIM14_IRQn = 19, /*!< TIM14 Interrupt */ TIM15_IRQn = 20, /*!< TIM15 Interrupt */ TIM16_IRQn = 21, /*!< TIM16 Interrupt */ TIM17_IRQn = 22, /*!< TIM17 Interrupt */ I2C1_IRQn = 23, /*!< I2C1 Interrupt */ I2C2_IRQn = 24, /*!< I2C2 Interrupt */ SPI1_IRQn = 25, /*!< SPI1 Interrupt */ SPI2_IRQn = 26, /*!< SPI2 Interrupt */ USART1_IRQn = 27, /*!< USART1 Interrupt */ USART2_IRQn = 28, /*!< USART2 Interrupt */ CEC_IRQn = 30 /*!< CEC Interrupt */ } IRQn_Type; /** * @} */ #include "core_cm0.h" #include "system_stm32f0xx.h" #include /** @addtogroup Exported_types * @{ */ typedef enum {RESET = 0, SET = !RESET} FlagStatus, ITStatus; typedef enum {DISABLE = 0, ENABLE = !DISABLE} FunctionalState; #define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE)) typedef enum {ERROR = 0, SUCCESS = !ERROR} ErrorStatus; /** @addtogroup Peripheral_registers_structures * @{ */ /** * @brief Analog to Digital Converter */ typedef struct { __IO uint32_t ISR; /*!< ADC Interrupt and Status register, Address offset:0x00 */ __IO uint32_t IER; /*!< ADC Interrupt Enable register, Address offset:0x04 */ __IO uint32_t CR; /*!< ADC Control register, Address offset:0x08 */ __IO uint32_t CFGR1; /*!< ADC Configuration register 1, Address offset:0x0C */ __IO uint32_t CFGR2; /*!< ADC Configuration register 2, Address offset:0x10 */ __IO uint32_t SMPR; /*!< ADC Sampling time register, Address offset:0x14 */ uint32_t RESERVED1; /*!< Reserved, 0x18 */ uint32_t RESERVED2; /*!< Reserved, 0x1C */ __IO uint32_t TR; /*!< ADC watchdog threshold register, Address offset:0x20 */ uint32_t RESERVED3; /*!< Reserved, 0x24 */ __IO uint32_t CHSELR; /*!< ADC channel selection register, Address offset:0x28 */ uint32_t RESERVED4[5]; /*!< Reserved, 0x2C */ __IO uint32_t DR; /*!< ADC data register, Address offset:0x40 */ } ADC_TypeDef; typedef struct { __IO uint32_t CCR; } ADC_Common_TypeDef; /** * @brief HDMI-CEC */ typedef struct { __IO uint32_t CR; /*!< CEC control register, Address offset:0x00 */ __IO uint32_t CFGR; /*!< CEC configuration register, Address offset:0x04 */ __IO uint32_t TXDR; /*!< CEC Tx data register , Address offset:0x08 */ __IO uint32_t RXDR; /*!< CEC Rx Data Register, Address offset:0x0C */ __IO uint32_t ISR; /*!< CEC Interrupt and Status Register, Address offset:0x10 */ __IO uint32_t IER; /*!< CEC interrupt enable register, Address offset:0x14 */ }CEC_TypeDef; /** * @brief Comparator */ typedef struct { __IO uint32_t CSR; /*!< COMP comparator control and status register, Address offset: 0x1C */ } COMP_TypeDef; /** * @brief CRC calculation unit */ typedef struct { __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ uint8_t RESERVED0; /*!< Reserved, 0x05 */ uint16_t RESERVED1; /*!< Reserved, 0x06 */ __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ uint32_t RESERVED2; /*!< Reserved, 0x0C */ __IO uint32_t INIT; /*!< Initial CRC value register, Address offset: 0x10 */ } CRC_TypeDef; /** * @brief Digital to Analog Converter */ typedef struct { __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ uint32_t RESERVED[6]; /*!< Reserved, 0x14 */ __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ uint32_t RESERVED1; /*!< Reserved, 0x30 */ __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ } DAC_TypeDef; /** * @brief Debug MCU */ typedef struct { __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ }DBGMCU_TypeDef; /** * @brief DMA Controller */ typedef struct { __IO uint32_t CCR; /*!< DMA channel x configuration register */ __IO uint32_t CNDTR; /*!< DMA channel x number of data register */ __IO uint32_t CPAR; /*!< DMA channel x peripheral address register */ __IO uint32_t CMAR; /*!< DMA channel x memory address register */ } DMA_Channel_TypeDef; typedef struct { __IO uint32_t ISR; /*!< DMA interrupt status register, Address offset: 0x00 */ __IO uint32_t IFCR; /*!< DMA interrupt flag clear register, Address offset: 0x04 */ } DMA_TypeDef; /** * @brief External Interrupt/Event Controller */ typedef struct { __IO uint32_t IMR; /*!