ARM: i.MX25: Karo TX25: Switch to devicetree support
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit is contained in:
parent
2cca917c48
commit
23f23a7224
|
@ -17,6 +17,8 @@
|
|||
*
|
||||
*/
|
||||
|
||||
#define pr_fmt(fmt) "tx25: " fmt
|
||||
|
||||
#include <common.h>
|
||||
#include <init.h>
|
||||
#include <driver.h>
|
||||
|
@ -31,8 +33,6 @@
|
|||
#include <partition.h>
|
||||
#include <generated/mach-types.h>
|
||||
#include <mach/imx-nand.h>
|
||||
#include <fec.h>
|
||||
#include <nand.h>
|
||||
#include <mach/iomux-mx25.h>
|
||||
#include <mach/generic.h>
|
||||
#include <mach/iim.h>
|
||||
|
@ -41,78 +41,51 @@
|
|||
#include <mach/bbu.h>
|
||||
#include <asm/mmu.h>
|
||||
|
||||
static struct fec_platform_data fec_info = {
|
||||
.xcv_type = PHY_INTERFACE_MODE_RMII,
|
||||
.phy_addr = 0x1f,
|
||||
};
|
||||
|
||||
struct imx_nand_platform_data nand_info = {
|
||||
.width = 1,
|
||||
.hw_ecc = 1,
|
||||
.flash_bbt = 1,
|
||||
};
|
||||
|
||||
static iomux_v3_cfg_t karo_tx25_padsd_fec[] = {
|
||||
MX25_PAD_D11__GPIO_4_9, /* FEC PHY power on pin */
|
||||
MX25_PAD_D13__GPIO_4_7, /* FEC reset */
|
||||
MX25_PAD_FEC_MDC__FEC_MDC,
|
||||
MX25_PAD_FEC_MDIO__FEC_MDIO,
|
||||
MX25_PAD_FEC_TDATA0__FEC_TDATA0,
|
||||
MX25_PAD_FEC_TDATA1__FEC_TDATA1,
|
||||
MX25_PAD_FEC_TX_EN__FEC_TX_EN,
|
||||
MX25_PAD_FEC_RDATA0__FEC_RDATA0,
|
||||
MX25_PAD_FEC_RDATA1__FEC_RDATA1,
|
||||
MX25_PAD_FEC_RX_DV__FEC_RX_DV,
|
||||
MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
|
||||
};
|
||||
|
||||
#define TX25_FEC_PWR_GPIO IMX_GPIO_NR(4, 9)
|
||||
#define TX25_FEC_RST_GPIO IMX_GPIO_NR(4, 7)
|
||||
|
||||
static struct gpio fec_gpios[] = {
|
||||
{
|
||||
.gpio = TX25_FEC_PWR_GPIO,
|
||||
.flags = GPIOF_OUT_INIT_LOW,
|
||||
.label = "fec-pwr",
|
||||
}, {
|
||||
.gpio = TX25_FEC_RST_GPIO,
|
||||
.flags = GPIOF_OUT_INIT_LOW,
|
||||
.label = "fec-rst",
|
||||
},
|
||||
};
|
||||
|
||||
static void noinline gpio_fec_active(void)
|
||||
{
|
||||
mxc_iomux_v3_setup_multiple_pads(karo_tx25_padsd_fec,
|
||||
ARRAY_SIZE(karo_tx25_padsd_fec));
|
||||
int ret;
|
||||
|
||||
/* power down phy, put into reset */
|
||||
gpio_direction_output(TX25_FEC_PWR_GPIO, 0);
|
||||
gpio_direction_output(TX25_FEC_RST_GPIO, 0);
|
||||
ret = gpio_request_array(fec_gpios, ARRAY_SIZE(fec_gpios));
|
||||
if (ret) {
|
||||
pr_err("Failed to request fec gpios: %s\n", strerror(-ret));
|
||||
return;
|
||||
}
|
||||
|
||||
udelay(10);
|
||||
|
||||
/* power up phy, get out of reset */
|
||||
gpio_direction_output(TX25_FEC_PWR_GPIO, 1);
|
||||
gpio_direction_output(TX25_FEC_RST_GPIO, 1);
|
||||
/* power up phy, but leave in reset */
|
||||
gpio_set_value(TX25_FEC_PWR_GPIO, 1);
|
||||
|
||||
udelay(100);
|
||||
|
||||
/* apply a reset to the powered phy again */
|
||||
gpio_direction_output(TX25_FEC_RST_GPIO, 0);
|
||||
udelay(100);
|
||||
gpio_direction_output(TX25_FEC_RST_GPIO, 1);
|
||||
/* FEC driver picks up the reset gpio later */
|
||||
gpio_free(TX25_FEC_RST_GPIO);
|
||||
}
|
||||
|
||||
static int tx25_devices_init(void)
|
||||
static int tx25_init(void)
|
||||
{
|
||||
if (!of_machine_is_compatible("karo,imx25-tx25"))
|
||||
return 0;
|
||||
|
||||
gpio_fec_active();
|
||||
|
||||
imx25_iim_register_fec_ethaddr();
|
||||
imx25_add_fec(&fec_info);
|
||||
|
||||
if (readl(MX25_CCM_BASE_ADDR + MX25_CCM_RCSR) & (1 << 14))
|
||||
nand_info.width = 2;
|
||||
|
||||
imx25_add_nand(&nand_info);
|
||||
|
||||
devfs_add_partition("nand0", 0x00000, SZ_512K, DEVFS_PARTITION_FIXED, "self_raw");
|
||||
dev_add_bb_dev("self_raw", "self0");
|
||||
|
||||
devfs_add_partition("nand0", SZ_512K, SZ_512K, DEVFS_PARTITION_FIXED, "env_raw");
|
||||
dev_add_bb_dev("env_raw", "env0");
|
||||
|
||||
add_mem_device("sram0", 0x78000000, 128 * 1024,
|
||||
IORESOURCE_MEM_WRITEABLE);
|
||||
|
||||
barebox_set_hostname("tx25");
|
||||
armlinux_set_architecture(MACH_TYPE_TX25);
|
||||
armlinux_set_serial(imx_uid());
|
||||
|
||||
|
@ -122,44 +95,7 @@ static int tx25_devices_init(void)
|
|||
return 0;
|
||||
}
|
||||
|
||||
device_initcall(tx25_devices_init);
|
||||
|
||||
static iomux_v3_cfg_t tx25_pads[] = {
|
||||
MX25_PAD_D12__GPIO_4_8,
|
||||
MX25_PAD_D10__GPIO_4_10,
|
||||
MX25_PAD_NF_CE0__NF_CE0,
|
||||
MX25_PAD_NFWE_B__NFWE_B,
|
||||
MX25_PAD_NFRE_B__NFRE_B,
|
||||
MX25_PAD_NFALE__NFALE,
|
||||
MX25_PAD_NFCLE__NFCLE,
|
||||
MX25_PAD_NFWP_B__NFWP_B,
|
||||
MX25_PAD_NFRB__NFRB,
|
||||
MX25_PAD_D7__D7,
|
||||
MX25_PAD_D6__D6,
|
||||
MX25_PAD_D5__D5,
|
||||
MX25_PAD_D4__D4,
|
||||
MX25_PAD_D3__D3,
|
||||
MX25_PAD_D2__D2,
|
||||
MX25_PAD_D1__D1,
|
||||
MX25_PAD_D0__D0,
|
||||
MX25_PAD_UART1_TXD__UART1_TXD,
|
||||
MX25_PAD_UART1_RXD__UART1_RXD,
|
||||
MX25_PAD_UART1_CTS__UART1_CTS,
|
||||
MX25_PAD_UART1_RTS__UART1_RTS,
|
||||
};
|
||||
|
||||
static int tx25_console_init(void)
|
||||
{
|
||||
mxc_iomux_v3_setup_multiple_pads(tx25_pads, ARRAY_SIZE(tx25_pads));
|
||||
|
||||
barebox_set_model("Ka-Ro TX25");
|
||||
barebox_set_hostname("tx25");
|
||||
|
||||
imx25_add_uart0();
|
||||
return 0;
|
||||
}
|
||||
|
||||
console_initcall(tx25_console_init);
|
||||
console_initcall(tx25_init);
|
||||
|
||||
static iomux_v3_cfg_t tx25_lcdc_gpios[] = {
|
||||
MX25_PAD_A18__GPIO_2_4, /* LCD Reset (active LOW) */
|
||||
|
@ -236,6 +172,12 @@ static struct imx_fb_platform_data tx25_fb_data = {
|
|||
|
||||
static int tx25_init_fb(void)
|
||||
{
|
||||
if (!IS_ENABLED(CONFIG_DRIVER_VIDEO_IMX))
|
||||
return 0;
|
||||
|
||||
if (!of_machine_is_compatible("karo,imx25-tx25"))
|
||||
return 0;
|
||||
|
||||
tx25_fb_enable(0);
|
||||
|
||||
mxc_iomux_v3_setup_multiple_pads(tx25_lcdc_gpios,
|
||||
|
|
|
@ -75,9 +75,12 @@ static inline void __bare_init setup_sdram(uint32_t base, uint32_t esdctl,
|
|||
writel(esdctl, esdctlreg);
|
||||
}
|
||||
|
||||
extern char __dtb_imx25_karo_tx25_start[];
|
||||
|
||||
void __bare_init __naked barebox_arm_reset_vector(void)
|
||||
{
|
||||
uint32_t r;
|
||||
uint32_t fdt;
|
||||
|
||||
arm_cpu_lowlevel_init();
|
||||
|
||||
|
@ -136,6 +139,8 @@ void __bare_init __naked barebox_arm_reset_vector(void)
|
|||
|
||||
setup_uart();
|
||||
|
||||
fdt = (uint32_t)__dtb_imx25_karo_tx25_start - get_runtime_offset();
|
||||
|
||||
/* Skip SDRAM initialization if we run from RAM */
|
||||
r = get_pc();
|
||||
if (r > 0x80000000 && r < 0xa0000000)
|
||||
|
@ -161,8 +166,8 @@ void __bare_init __naked barebox_arm_reset_vector(void)
|
|||
/* setup a stack to be able to call imx25_barebox_boot_nand_external() */
|
||||
arm_setup_stack(MX25_IRAM_BASE_ADDR + MX25_IRAM_SIZE - 8);
|
||||
|
||||
imx25_barebox_boot_nand_external(0);
|
||||
imx25_barebox_boot_nand_external(fdt);
|
||||
#endif
|
||||
out:
|
||||
imx25_barebox_entry(0);
|
||||
imx25_barebox_entry(fdt);
|
||||
}
|
||||
|
|
|
@ -1,7 +1,8 @@
|
|||
CONFIG_BUILTIN_DTB=y
|
||||
CONFIG_BUILTIN_DTB_NAME="imx25-karo-tx25"
|
||||
CONFIG_ARCH_IMX=y
|
||||
CONFIG_ARCH_IMX_EXTERNAL_BOOT=y
|
||||
CONFIG_ARCH_IMX_EXTERNAL_BOOT_NAND=y
|
||||
CONFIG_ARCH_IMX25=y
|
||||
CONFIG_MACH_TX25=y
|
||||
CONFIG_IMX_IIM=y
|
||||
CONFIG_AEABI=y
|
||||
|
@ -17,6 +18,7 @@ CONFIG_LONGHELP=y
|
|||
CONFIG_HUSH_FANCY_PROMPT=y
|
||||
CONFIG_CMDLINE_EDITING=y
|
||||
CONFIG_AUTO_COMPLETE=y
|
||||
CONFIG_CONSOLE_ACTIVATE_NONE=y
|
||||
CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
|
||||
CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/karo-tx25/env"
|
||||
CONFIG_RESET_SOURCE=y
|
||||
|
@ -28,9 +30,7 @@ CONFIG_CMD_EXPORT=y
|
|||
CONFIG_CMD_PRINTENV=y
|
||||
CONFIG_CMD_READLINE=y
|
||||
CONFIG_CMD_TIME=y
|
||||
CONFIG_CMD_DIRNAME=y
|
||||
CONFIG_CMD_LN=y
|
||||
CONFIG_CMD_READLINK=y
|
||||
CONFIG_CMD_TFTP=y
|
||||
CONFIG_CMD_FILETYPE=y
|
||||
CONFIG_CMD_ECHO_E=y
|
||||
|
@ -40,7 +40,6 @@ CONFIG_CMD_CRC=y
|
|||
CONFIG_CMD_CRC_CMP=y
|
||||
CONFIG_CMD_MD5SUM=y
|
||||
CONFIG_CMD_FLASH=y
|
||||
CONFIG_CMD_UBIFORMAT=y
|
||||
CONFIG_CMD_BOOTM_SHOW_TYPE=y
|
||||
CONFIG_CMD_BOOTM_VERBOSE=y
|
||||
CONFIG_CMD_BOOTM_INITRD=y
|
||||
|
@ -51,10 +50,10 @@ CONFIG_CMD_UIMAGE=y
|
|||
CONFIG_CMD_RESET=y
|
||||
CONFIG_CMD_GO=y
|
||||
CONFIG_CMD_OFTREE=y
|
||||
CONFIG_CMD_OFTREE_PROBE=y
|
||||
CONFIG_CMD_MTEST=y
|
||||
CONFIG_CMD_MTEST_ALTERNATIVE=y
|
||||
CONFIG_CMD_OF_PROPERTY=y
|
||||
CONFIG_CMD_OF_NODE=y
|
||||
CONFIG_CMD_SPLASH=y
|
||||
CONFIG_CMD_BAREBOX_UPDATE=y
|
||||
CONFIG_CMD_TIMEOUT=y
|
||||
CONFIG_CMD_PARTITION=y
|
||||
CONFIG_CMD_MAGICVAR=y
|
||||
|
@ -63,20 +62,24 @@ CONFIG_CMD_GPIO=y
|
|||
CONFIG_CMD_UNCOMPRESS=y
|
||||
CONFIG_CMD_MIITOOL=y
|
||||
CONFIG_CMD_CLK=y
|
||||
CONFIG_CMD_DETECT=y
|
||||
CONFIG_CMD_WD=y
|
||||
CONFIG_NET=y
|
||||
CONFIG_NET_DHCP=y
|
||||
CONFIG_NET_PING=y
|
||||
CONFIG_NET_NETCONSOLE=y
|
||||
CONFIG_OFDEVICE=y
|
||||
CONFIG_OF_BAREBOX_DRIVERS=y
|
||||
CONFIG_DRIVER_NET_FEC_IMX=y
|
||||
# CONFIG_SPI is not set
|
||||
CONFIG_MTD=y
|
||||
CONFIG_NAND=y
|
||||
CONFIG_NAND_IMX=y
|
||||
CONFIG_UBI=y
|
||||
CONFIG_VIDEO=y
|
||||
CONFIG_DRIVER_VIDEO_IMX=y
|
||||
CONFIG_MCI=y
|
||||
CONFIG_MCI_IMX_ESDHC=y
|
||||
CONFIG_SRAM=y
|
||||
CONFIG_WATCHDOG=y
|
||||
CONFIG_WATCHDOG_IMX=y
|
||||
CONFIG_FS_TFTP=y
|
||||
|
|
|
@ -49,6 +49,7 @@ pbl-$(CONFIG_MACH_TORADEX_COLIBRI_T20_IRIS) += tegra20-colibri-iris.dtb.o
|
|||
pbl-$(CONFIG_MACH_TOSHIBA_AC100) += tegra20-paz00.dtb.o
|
||||
pbl-$(CONFIG_MACH_TQMA53) += imx53-mba53.dtb.o
|
||||
pbl-$(CONFIG_MACH_TQMA6X) += imx6dl-mba6x.dtb.o imx6q-mba6x.dtb.o
|
||||
pbl-$(CONFIG_MACH_TX25) += imx25-karo-tx25.dtb.o
|
||||
pbl-$(CONFIG_MACH_SOCFPGA_EBV_SOCRATES) += socfpga_cyclone5_socrates.dtb.o
|
||||
pbl-$(CONFIG_MACH_SOCFPGA_TERASIC_SOCKIT) += socfpga_cyclone5_sockit.dtb.o
|
||||
pbl-$(CONFIG_MACH_SOLIDRUN_HUMMINGBOARD) += imx6dl-hummingboard.dtb.o
|
||||
|
|
Loading…
Reference in New Issue