sysmo-bts
/
barebox
9
0
Fork 0
Code Releases Activity

dts: update to v4.11-rc1 

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit is contained in:
Sascha Hauer 2017-03-10 08:56:15 +01:00
parent cc2392cf4f
commit 957bb6b6bc
968 changed files with 32796 additions and 9498 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

2
dts/Bindings/arm/amlogic.txt
View File

@ -40,6 +40,8 @@ Board compatible values:
- "hardkernel,odroid-c2" (Meson gxbb)
- "amlogic,p200" (Meson gxbb)
- "amlogic,p201" (Meson gxbb)
- "wetek,hub" (Meson gxbb)
- "wetek,play2" (Meson gxbb)
- "amlogic,p212" (Meson gxl s905x)
- "amlogic,p230" (Meson gxl s905d)
- "amlogic,p231" (Meson gxl s905d)

6
dts/Bindings/arm/arch_timer.txt
View File

@ -31,6 +31,12 @@ to deliver its interrupts via SPIs.
This also affects writes to the tval register, due to the implicit
counter read.
- hisilicon,erratum-161010101 : A boolean property. Indicates the
presence of Hisilicon erratum 161010101, which says that reading the
counters is unreliable in some cases, and reads may return a value 32
beyond the correct value. This also affects writes to the tval
registers, due to the implicit counter read.
** Optional properties:
- arm,cpu-registers-not-fw-configured : Firmware does not initialize

19
dts/Bindings/arm/axentia.txt Normal file
View File

@ -0,0 +1,19 @@
Device tree bindings for Axentia ARM devices
============================================
Linea CPU module
----------------
Required root node properties:
compatible = "axentia,linea",
"atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
and following the rules from atmel-at91.txt for a sama5d31 SoC.
TSE-850 v3 board
----------------
Required root node properties:
compatible = "axentia,tse850v3", "axentia,linea",
"atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
and following the rules from above for the axentia,linea CPU module.

2
dts/Bindings/arm/cpus.txt
View File

@ -158,6 +158,7 @@ nodes to be present and contain the properties described below.
"arm,cortex-a53"
"arm,cortex-a57"
"arm,cortex-a72"
"arm,cortex-a73"
"arm,cortex-m0"
"arm,cortex-m0+"
"arm,cortex-m1"
@ -202,6 +203,7 @@ nodes to be present and contain the properties described below.
"marvell,armada-380-smp"
"marvell,armada-390-smp"
"marvell,armada-xp-smp"
"marvell,98dx3236-smp"
"mediatek,mt6589-smp"
"mediatek,mt81xx-tz-smp"
"qcom,gcc-msm8660"

4
dts/Bindings/arm/davinci.txt
View File

@ -13,6 +13,10 @@ EnBW AM1808 based CMC board
Required root node properties:
- compatible = "enbw,cmc", "ti,da850;
LEGO MINDSTORMS EV3 (AM1808 based)
Required root node properties:
- compatible = "lego,ev3", "ti,da850";
Generic DaVinci Boards
----------------------

20
dts/Bindings/arm/fsl.txt
View File

@ -108,7 +108,7 @@ status.
- compatible: Should contain a chip-specific compatible string,
Chip-specific strings are of the form "fsl,<chip>-scfg",
The following <chip>s are known to be supported:
ls1021a, ls1043a, ls1046a, ls2080a.
ls1012a, ls1021a, ls1043a, ls1046a, ls2080a.
- reg: should contain base address and length of SCFG memory-mapped registers
@ -126,7 +126,7 @@ core start address and release the secondary core from holdoff and startup.
- compatible: Should contain a chip-specific compatible string,
Chip-specific strings are of the form "fsl,<chip>-dcfg",
The following <chip>s are known to be supported:
ls1021a, ls1043a, ls1046a, ls2080a.
ls1012a, ls1021a, ls1043a, ls1046a, ls2080a.
- reg : should contain base address and length of DCFG memory-mapped registers
@ -139,6 +139,22 @@ Example:
Freescale ARMv8 based Layerscape SoC family Device Tree Bindings
----------------------------------------------------------------
LS1012A SoC
Required root node properties:
- compatible = "fsl,ls1012a";
LS1012A ARMv8 based RDB Board
Required root node properties:
- compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
LS1012A ARMv8 based FRDM Board
Required root node properties:
- compatible = "fsl,ls1012a-frdm", "fsl,ls1012a";
LS1012A ARMv8 based QDS Board
Required root node properties:
- compatible = "fsl,ls1012a-qds", "fsl,ls1012a";
LS1043A SoC
Required root node properties:
- compatible = "fsl,ls1043a";

4
dts/Bindings/arm/hisilicon/hisilicon.txt
View File

@ -1,5 +1,9 @@
Hisilicon Platforms Device Tree Bindings
----------------------------------------------------
Hi3660 SoC
Required root node properties:
- compatible = "hisilicon,hi3660";
Hi4511 Board
Required root node properties:
- compatible = "hisilicon,hi3620-hi4511";

16
dts/Bindings/arm/marvell/98dx3236-resume-ctrl.txt Normal file
View File

@ -0,0 +1,16 @@
Resume Control
--------------
Available on Marvell SOCs: 98DX3336 and 98DX4251
Required properties:
- compatible: must be "marvell,98dx3336-resume-ctrl"
- reg: Should contain resume control registers location and length
Example:
resume@20980 {
compatible = "marvell,98dx3336-resume-ctrl";
reg = <0x20980 0x10>;
};

23
dts/Bindings/arm/marvell/98dx3236.txt Normal file
View File

@ -0,0 +1,23 @@
Marvell 98DX3236, 98DX3336 and 98DX4251 Platforms Device Tree Bindings
----------------------------------------------------------------------
Boards with a SoC of the Marvell 98DX3236, 98DX3336 and 98DX4251 families
shall have the following property:
Required root node property:
compatible: must contain "marvell,armadaxp-98dx3236"
In addition, boards using the Marvell 98DX3336 SoC shall have the
following property:
Required root node property:
compatible: must contain "marvell,armadaxp-98dx3336"
In addition, boards using the Marvell 98DX4251 SoC shall have the
following property:
Required root node property:
compatible: must contain "marvell,armadaxp-98dx4251"

3
dts/Bindings/arm/omap/omap.txt
View File

@ -151,6 +151,9 @@ Boards:
- AM335X SBC-T335 : single board computer, built around the Sitara AM3352/4
compatible = "compulab,sbc-t335", "compulab,cm-t335", "ti,am33xx"
- AM335X phyCORE-AM335x: Development kit
compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
- OMAP5 EVM : Evaluation Module
compatible = "ti,omap5-evm", "ti,omap5"

2
dts/Bindings/arm/shmobile.txt
View File

@ -75,7 +75,7 @@ Boards:
compatible = "renesas,rskrza1", "renesas,r7s72100"
- Salvator-X (RTP0RC7795SIPB0010S)
compatible = "renesas,salvator-x", "renesas,r8a7795";
- Salvator-X
- Salvator-X (RTP0RC7796SIPB0011S)
compatible = "renesas,salvator-x", "renesas,r8a7796";
- SILK (RTP0RC7794LCB00011S)
compatible = "renesas,silk", "renesas,r8a7794"

1
dts/Bindings/arm/sunxi.txt
View File

@ -12,6 +12,7 @@ using one of the following compatible strings:
allwinner,sun8i-a23
allwinner,sun8i-a33
allwinner,sun8i-a83t
allwinner,sun8i-h2-plus
allwinner,sun8i-h3
allwinner,sun9i-a80
allwinner,sun50i-a64

18
dts/Bindings/ata/ahci-da850.txt Normal file
View File

@ -0,0 +1,18 @@
Device tree binding for the TI DA850 AHCI SATA Controller
---------------------------------------------------------
Required properties:
- compatible: must be "ti,da850-ahci"
- reg: physical base addresses and sizes of the two register regions
used by the controller: the register map as defined by the
AHCI 1.1 standard and the Power Down Control Register (PWRDN)
for enabling/disabling the SATA clock receiver
- interrupts: interrupt specifier (refer to the interrupt binding)
Example:
sata: sata@218000 {
compatible = "ti,da850-ahci";
reg = <0x218000 0x2000>, <0x22c018 0x4>;
interrupts = <67>;
};

6
dts/Bindings/bus/qcom,ebi2.txt
View File

@ -51,7 +51,7 @@ Required properties:
- compatible: should be one of:
"qcom,msm8660-ebi2"
"qcom,apq8060-ebi2"
- #address-cells: shoule be <2>: the first cell is the chipselect,
- #address-cells: should be <2>: the first cell is the chipselect,
the second cell is the offset inside the memory range
- #size-cells: should be <1>
- ranges: should be set to:
@ -64,7 +64,7 @@ Required properties:
- reg: two ranges of registers: EBI2 config and XMEM config areas
- reg-names: should be "ebi2", "xmem"
- clocks: two clocks, EBI_2X and EBI
- clock-names: shoule be "ebi2x", "ebi2"
- clock-names: should be "ebi2x", "ebi2"
Optional subnodes:
- Nodes inside the EBI2 will be considered device nodes.
@ -100,7 +100,7 @@ Optional properties arrays for FAST chip selects:
assertion, with respect to the cycle where ADV (address valid) is asserted.
2 means 2 cycles between ADV and OE. Valid values 0, 1, 2 or 3.
- qcom,xmem-read-hold-cycles: the length in cycles of the first segment of a
read transfer. For a single read trandfer this will be the time from CS
read transfer. For a single read transfer this will be the time from CS
assertion to OE assertion. Valid values 0 thru 15.

15
dts/Bindings/clock/brcm,bcm2835-cprman.txt
View File

@ -16,7 +16,20 @@ Required properties:
- #clock-cells: Should be <1>. The permitted clock-specifier values can be
found in include/dt-bindings/clock/bcm2835.h
- reg: Specifies base physical address and size of the registers
- clocks: The external oscillator clock phandle
- clocks: phandles to the parent clocks used as input to the module, in
the following order:
- External oscillator
- DSI0 byte clock
- DSI0 DDR2 clock
- DSI0 DDR clock
- DSI1 byte clock
- DSI1 DDR2 clock
- DSI1 DDR clock
Only external oscillator is required. The DSI clocks may
not be present, in which case their children will be
unusable.
Example:

38
dts/Bindings/clock/exynos4415-clock.txt
View File

@ -1,38 +0,0 @@
* Samsung Exynos4415 Clock Controller
The Exynos4415 clock controller generates and supplies clock to various
consumer devices within the Exynos4415 SoC.
Required properties:
- compatible: should be one of the following:
- "samsung,exynos4415-cmu" - for the main system clocks controller
(CMU_LEFTBUS, CMU_RIGHTBUS, CMU_TOP, CMU_CPU clock domains).
- "samsung,exynos4415-cmu-dmc" - for the Exynos4415 SoC DRAM Memory
Controller (DMC) domain clock controller.
- reg: physical base address of the controller and length of memory mapped
region.
- #clock-cells: should be 1.
Each clock is assigned an identifier and client nodes can use this identifier
to specify the clock which they consume.
All available clocks are defined as preprocessor macros in
dt-bindings/clock/exynos4415.h header and can be used in device
tree sources.
Example 1: An example of a clock controller node is listed below.
cmu: clock-controller@10030000 {
compatible = "samsung,exynos4415-cmu";
reg = <0x10030000 0x18000>;
#clock-cells = <1>;
};
cmu-dmc: clock-controller@105C0000 {
compatible = "samsung,exynos4415-cmu-dmc";
reg = <0x105C0000 0x3000>;
#clock-cells = <1>;
};

42
dts/Bindings/clock/hi3660-clock.txt Normal file
View File

@ -0,0 +1,42 @@
* Hisilicon Hi3660 Clock Controller
The Hi3660 clock controller generates and supplies clock to various
controllers within the Hi3660 SoC.
Required Properties:
- compatible: the compatible should be one of the following strings to
indicate the clock controller functionality.
- "hisilicon,hi3660-crgctrl"
- "hisilicon,hi3660-pctrl"
- "hisilicon,hi3660-pmuctrl"
- "hisilicon,hi3660-sctrl"
- "hisilicon,hi3660-iomcu"
- reg: physical base address of the controller and length of memory mapped
region.
- #clock-cells: should be 1.
Each clock is assigned an identifier and client nodes use this identifier
to specify the clock which they consume.
All these identifier could be found in <dt-bindings/clock/hi3660-clock.h>.
Examples:
crg_ctrl: clock-controller@fff35000 {
compatible = "hisilicon,hi3660-crgctrl", "syscon";
reg = <0x0 0xfff35000 0x0 0x1000>;
#clock-cells = <1>;
};
uart0: serial@fdf02000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x0 0xfdf02000 0x0 0x1000>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&crg_ctrl HI3660_CLK_MUX_UART0>,
<&crg_ctrl HI3660_PCLK>;
clock-names = "uartclk", "apb_pclk";
status = "disabled";
};

65
dts/Bindings/clock/idt,versaclock5.txt Normal file
View File

@ -0,0 +1,65 @@
Binding for IDT VersaClock5 programmable i2c clock generator.
The IDT VersaClock5 are programmable i2c clock generators providing
from 3 to 12 output clocks.
==I2C device node==
Required properties:
- compatible: shall be one of "idt,5p49v5923" , "idt,5p49v5933".
- reg: i2c device address, shall be 0x68 or 0x6a.
- #clock-cells: from common clock binding; shall be set to 1.
- clocks: from common clock binding; list of parent clock handles,
- 5p49v5923: (required) either or both of XTAL or CLKIN
reference clock.
- 5p49v5933: (optional) property not present (internal
Xtal used) or CLKIN reference
clock.
- clock-names: from common clock binding; clock input names, can be
- 5p49v5923: (required) either or both of "xin", "clkin".
- 5p49v5933: (optional) property not present or "clkin".
==Mapping between clock specifier and physical pins==
When referencing the provided clock in the DT using phandle and
clock specifier, the following mapping applies:
5P49V5923:
0 -- OUT0_SEL_I2CB
1 -- OUT1
2 -- OUT2
5P49V5933:
0 -- OUT0_SEL_I2CB
1 -- OUT1
2 -- OUT4
==Example==
/* 25MHz reference crystal */
ref25: ref25m {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
i2c-master-node {
/* IDT 5P49V5923 i2c clock generator */
vc5: clock-generator@6a {
compatible = "idt,5p49v5923";
reg = <0x6a>;
#clock-cells = <1>;
/* Connect XIN input to 25MHz reference */
clocks = <&ref25m>;
clock-names = "xin";
};
};
/* Consumer referencing the 5P49V5923 pin OUT1 */
consumer {
...
clocks = <&vc5 1>;
...
}

1
dts/Bindings/clock/mvebu-corediv-clock.txt
View File

@ -7,6 +7,7 @@ Required properties:
- compatible : must be "marvell,armada-370-corediv-clock",
"marvell,armada-375-corediv-clock",
"marvell,armada-380-corediv-clock",
"marvell,mv98dx3236-corediv-clock",
- reg : must be the register address of Core Divider control register
- #clock-cells : from common clock binding; shall be set to 1

1
dts/Bindings/clock/mvebu-cpu-clock.txt
View File

@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms
Required properties:
- compatible : shall be one of the following:
"marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP
"marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC
- reg : Address and length of the clock complex register set, followed
by address and length of the PMU DFS registers
- #clock-cells : should be set to 1.

2
dts/Bindings/clock/mvebu-gated-clock.txt
View File

@ -117,7 +117,7 @@ ID Clock Peripheral
25 tdm Time Division Mplx
28 xor1 XOR DMA 1
29 sata1lnk
30 sata1 SATA Host 0
30 sata1 SATA Host 1
The following is a list of provided IDs for Dove:
ID Clock Peripheral

1
dts/Bindings/clock/qcom,rpmcc.txt
View File

@ -11,6 +11,7 @@ Required properties :
compatible "qcom,rpmcc" should be also included.
"qcom,rpmcc-msm8916", "qcom,rpmcc"
"qcom,rpmcc-msm8974", "qcom,rpmcc"
"qcom,rpmcc-apq8064", "qcom,rpmcc"
- #clock-cells : shall contain 1

1
dts/Bindings/clock/qoriq-clock.txt
View File

@ -31,6 +31,7 @@ Required properties:
* "fsl,t4240-clockgen"
* "fsl,b4420-clockgen"
* "fsl,b4860-clockgen"
* "fsl,ls1012a-clockgen"
* "fsl,ls1021a-clockgen"
* "fsl,ls1043a-clockgen"
* "fsl,ls1046a-clockgen"

6
dts/Bindings/clock/renesas,cpg-mssr.txt
View File

@ -42,6 +42,10 @@ Required Properties:
Domain bindings in
Documentation/devicetree/bindings/power/power_domain.txt.
- #reset-cells: Must be 1
- The single reset specifier cell must be the module number, as defined
in the datasheet.
Examples
--------
@ -55,6 +59,7 @@ Examples
clock-names = "extal", "extalr";
#clock-cells = <2>;
#power-domain-cells = <0>;
#reset-cells = <1>;
};
@ -69,5 +74,6 @@ Examples
dmas = <&dmac1 0x13>, <&dmac1 0x12>;
dma-names = "tx", "rx";
power-domains = <&cpg>;
resets = <&cpg 310>;
status = "disabled";
};

57
dts/Bindings/clock/rockchip,rk3328-cru.txt Normal file
View File

@ -0,0 +1,57 @@
* Rockchip RK3328 Clock and Reset Unit
The RK3328 clock controller generates and supplies clock to various
controllers within the SoC and also implements a reset controller for SoC
peripherals.
Required Properties:
- compatible: should be "rockchip,rk3328-cru"
- reg: physical base address of the controller and length of memory mapped
region.
- #clock-cells: should be 1.
- #reset-cells: should be 1.
Optional Properties:
- rockchip,grf: phandle to the syscon managing the "general register files"
If missing pll rates are not changeable, due to the missing pll lock status.
Each clock is assigned an identifier and client nodes can use this identifier
to specify the clock which they consume. All available clocks are defined as
preprocessor macros in the dt-bindings/clock/rk3328-cru.h headers and can be
used in device tree sources. Similar macros exist for the reset sources in
these files.
External clocks:
There are several clocks that are generated outside the SoC. It is expected
that they are defined using standard clock bindings with following
clock-output-names:
- "xin24m" - crystal input - required,
- "clkin_i2s" - external I2S clock - optional,
- "gmac_clkin" - external GMAC clock - optional
- "phy_50m_out" - output clock of the pll in the mac phy
Example: Clock controller node:
cru: clock-controller@ff440000 {
compatible = "rockchip,rk3328-cru";
reg = <0x0 0xff440000 0x0 0x1000>;
rockchip,grf = <&grf>;
#clock-cells = <1>;
#reset-cells = <1>;
};
Example: UART controller node that consumes the clock generated by the clock
controller:
uart0: serial@ff120000 {
compatible = "snps,dw-apb-uart";
reg = <0xff120000 0x100>;
interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&cru SCLK_UART0>;
};

6
dts/Bindings/clock/rockchip,rk3399-cru.txt
View File

@ -13,6 +13,12 @@ Required Properties:
- #clock-cells: should be 1.
- #reset-cells: should be 1.
Optional Properties:
- rockchip,grf: phandle to the syscon managing the "general register files".
It is used for GRF muxes, if missing any muxes present in the GRF will not
be available.
Each clock is assigned an identifier and client nodes can use this identifier
to specify the clock which they consume. All available clocks are defined as
preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be

37
dts/Bindings/clock/st,stm32-rcc.txt
View File

@ -10,6 +10,7 @@ Required properties:
- compatible: Should be:
"st,stm32f42xx-rcc"
"st,stm32f469-rcc"
"st,stm32f746-rcc"
- reg: should be register base and length as documented in the
datasheet
- #reset-cells: 1, see below
@ -17,6 +18,9 @@ Required properties:
property, containing a phandle to the clock device node, an index selecting
between gated clocks and other clocks and an index specifying the clock to
use.
- clocks: External oscillator clock phandle
- high speed external clock signal (HSE)
- external I2S clock (I2S_CKIN)
Example:
@ -25,6 +29,7 @@ Example:
#clock-cells = <2>
compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
reg = <0x40023800 0x400>;
clocks = <&clk_hse>, <&clk_i2s_ckin>;
};
Specifying gated clocks
@ -66,6 +71,38 @@ The secondary index is bound with the following magic numbers:
0 SYSTICK
1 FCLK
2 CLK_LSI (low-power clock source)
3 CLK_LSE (generated from a 32.768 kHz low-speed external
crystal or ceramic resonator)
4 CLK_HSE_RTC (HSE division factor for RTC clock)
5 CLK_RTC (real-time clock)
6 PLL_VCO_I2S (vco frequency of I2S pll)
7 PLL_VCO_SAI (vco frequency of SAI pll)
8 CLK_LCD (LCD-TFT)
9 CLK_I2S (I2S clocks)
10 CLK_SAI1 (audio clocks)
11 CLK_SAI2
12 CLK_I2SQ_PDIV (post divisor of pll i2s q divisor)
13 CLK_SAIQ_PDIV (post divisor of pll sai q divisor)
14 CLK_HSI (Internal ocscillator clock)
15 CLK_SYSCLK (System Clock)
16 CLK_HDMI_CEC (HDMI-CEC clock)
17 CLK_SPDIF (SPDIF-Rx clock)
18 CLK_USART1 (U(s)arts clocks)
19 CLK_USART2
20 CLK_USART3
21 CLK_UART4
22 CLK_UART5
23 CLK_USART6
24 CLK_UART7
25 CLK_UART8
26 CLK_I2C1 (I2S clocks)
27 CLK_I2C2
28 CLK_I2C3
29 CLK_I2C4
30 CLK_LPTIMER (LPTimer1 clock)
)
Example:

20
dts/Bindings/clock/stericsson,abx500.txt Normal file
View File

@ -0,0 +1,20 @@
Clock bindings for ST-Ericsson ABx500 clocks
Required properties :
- compatible : shall contain the following:
"stericsson,ab8500-clk"
- #clock-cells should be <1>
The ABx500 clocks need to be placed as a subnode of an AB8500
device node, see mfd/ab8500.txt
All available clocks are defined as preprocessor macros in
dt-bindings/clock/ste-ab8500.h header and can be used in device
tree sources.
Example:
clock-controller {
compatible = "stericsson,ab8500-clk";
#clock-cells = <1>;
};

28
dts/Bindings/clock/sun9i-de.txt Normal file
View File

@ -0,0 +1,28 @@
Allwinner A80 Display Engine Clock Control Binding
--------------------------------------------------
Required properties :
- compatible: must contain one of the following compatibles:
- "allwinner,sun9i-a80-de-clks"
- reg: Must contain the registers base address and length
- clocks: phandle to the clocks feeding the display engine subsystem.
Three are needed:
- "mod": the display engine module clock
- "dram": the DRAM bus clock for the system
- "bus": the bus clock for the whole display engine subsystem
- clock-names: Must contain the clock names described just above
- resets: phandle to the reset control for the display engine subsystem.
- #clock-cells : must contain 1
- #reset-cells : must contain 1
Example:
de_clocks: clock@3000000 {
compatible = "allwinner,sun9i-a80-de-clks";
reg = <0x03000000 0x30>;
clocks = <&ccu CLK_DE>, <&ccu CLK_SDRAM>, <&ccu CLK_BUS_DE>;
clock-names = "mod", "dram", "bus";
resets = <&ccu RST_BUS_DE>;
#clock-cells = <1>;
#reset-cells = <1>;
};

24
dts/Bindings/clock/sun9i-usb.txt Normal file
View File

@ -0,0 +1,24 @@
Allwinner A80 USB Clock Control Binding
---------------------------------------
Required properties :
- compatible: must contain one of the following compatibles:
- "allwinner,sun9i-a80-usb-clocks"
- reg: Must contain the registers base address and length
- clocks: phandle to the clocks feeding the USB subsystem. Two are needed:
- "bus": the bus clock for the whole USB subsystem
- "hosc": the high frequency oscillator (usually at 24MHz)
- clock-names: Must contain the clock names described just above
- #clock-cells : must contain 1
- #reset-cells : must contain 1
Example:
usb_clocks: clock@a08000 {
compatible = "allwinner,sun9i-a80-usb-clks";
reg = <0x00a08000 0x8>;
clocks = <&ccu CLK_BUS_USB>, <&osc24M>;
clock-names = "bus", "hosc";
#clock-cells = <1>;
#reset-cells = <1>;
};

2
dts/Bindings/clock/sunxi-ccu.txt
View File

@ -7,6 +7,8 @@ Required properties :
- "allwinner,sun8i-a23-ccu"
- "allwinner,sun8i-a33-ccu"
- "allwinner,sun8i-h3-ccu"
- "allwinner,sun8i-v3s-ccu"
- "allwinner,sun9i-a80-ccu"
- "allwinner,sun50i-a64-ccu"
- reg: Must contain the registers base address and length

15
dts/Bindings/clock/ti,cdce925.txt
View File

@ -1,15 +1,22 @@
Binding for TO CDCE925 programmable I2C clock synthesizers.
Binding for TI CDCE913/925/937/949 programmable I2C clock synthesizers.
Reference
This binding uses the common clock binding[1].
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
[2] http://www.ti.com/product/cdce925
[2] http://www.ti.com/product/cdce913
[3] http://www.ti.com/product/cdce925
[4] http://www.ti.com/product/cdce937
[5] http://www.ti.com/product/cdce949
The driver provides clock sources for each output Y1 through Y5.
Required properties:
- compatible: Shall be "ti,cdce925"
- compatible: Shall be one of the following:
- "ti,cdce913": 1-PLL, 3 Outputs
- "ti,cdce925": 2-PLL, 5 Outputs
- "ti,cdce937": 3-PLL, 7 Outputs
- "ti,cdce949": 4-PLL, 9 Outputs
- reg: I2C device address.
- clocks: Points to a fixed parent clock that provides the input frequency.
- #clock-cells: From common clock bindings: Shall be 1.
@ -18,7 +25,7 @@ Optional properties:
- xtal-load-pf: Crystal load-capacitor value to fine-tune performance on a
board, or to compensate for external influences.
For both PLL1 and PLL2 an optional child node can be used to specify spread
For all PLL1, PLL2, ... an optional child node can be used to specify spread
spectrum clocking parameters for a board.
- spread-spectrum: SSC mode as defined in the data sheet.
- spread-spectrum-center: Use "centered" mode instead of "max" mode. When

3
dts/Bindings/clock/zx296718-clk.txt
View File

@ -13,6 +13,9 @@ Required properties:
"zte,zx296718-lsp1crm":
zx296718 device level clock selection and gating
"zte,zx296718-audiocrm":
zx296718 audio clock selection, divider and gating
- reg: Address and length of the register set
The clock consumer should specify the desired clock by having the clock

128
dts/Bindings/cpufreq/ti-cpufreq.txt Normal file
View File

@ -0,0 +1,128 @@
TI CPUFreq and OPP bindings
================================
Certain TI SoCs, like those in the am335x, am437x, am57xx, and dra7xx
families support different OPPs depending on the silicon variant in use.
The ti-cpufreq driver can use revision and an efuse value from the SoC to
provide the OPP framework with supported hardware information. This is
used to determine which OPPs from the operating-points-v2 table get enabled
when it is parsed by the OPP framework.
Required properties:
--------------------
In 'cpus' nodes:
- operating-points-v2: Phandle to the operating-points-v2 table to use.
In 'operating-points-v2' table:
- compatible: Should be
- 'operating-points-v2-ti-cpu' for am335x, am43xx, and dra7xx/am57xx SoCs
- syscon: A phandle pointing to a syscon node representing the control module
register space of the SoC.
Optional properties:
--------------------
For each opp entry in 'operating-points-v2' table:
- opp-supported-hw: Two bitfields indicating:
1. Which revision of the SoC the OPP is supported by
2. Which eFuse bits indicate this OPP is available
A bitwise AND is performed against these values and if any bit
matches, the OPP gets enabled.
Example:
--------
/* From arch/arm/boot/dts/am33xx.dtsi */
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
compatible = "arm,cortex-a8";
device_type = "cpu";
reg = <0>;
operating-points-v2 = <&cpu0_opp_table>;
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
clock-latency = <300000>; /* From omap-cpufreq driver */
};
};
/*
* cpu0 has different OPPs depending on SoC revision and some on revisions
* 0x2 and 0x4 have eFuse bits that indicate if they are available or not
*/
cpu0_opp_table: opp-table {
compatible = "operating-points-v2-ti-cpu";
syscon = <&scm_conf>;
/*
* The three following nodes are marked with opp-suspend
* because they can not be enabled simultaneously on a
* single SoC.
*/
opp50@300000000 {
opp-hz = /bits/ 64 <300000000>;
opp-microvolt = <950000 931000 969000>;
opp-supported-hw = <0x06 0x0010>;
opp-suspend;
};
opp100@275000000 {
opp-hz = /bits/ 64 <275000000>;
opp-microvolt = <1100000 1078000 1122000>;
opp-supported-hw = <0x01 0x00FF>;
opp-suspend;
};
opp100@300000000 {
opp-hz = /bits/ 64 <300000000>;
opp-microvolt = <1100000 1078000 1122000>;
opp-supported-hw = <0x06 0x0020>;
opp-suspend;
};
opp100@500000000 {
opp-hz = /bits/ 64 <500000000>;
opp-microvolt = <1100000 1078000 1122000>;
opp-supported-hw = <0x01 0xFFFF>;
};
opp100@600000000 {
opp-hz = /bits/ 64 <600000000>;
opp-microvolt = <1100000 1078000 1122000>;
opp-supported-hw = <0x06 0x0040>;
};
opp120@600000000 {
opp-hz = /bits/ 64 <600000000>;
opp-microvolt = <1200000 1176000 1224000>;
opp-supported-hw = <0x01 0xFFFF>;
};
opp120@720000000 {
opp-hz = /bits/ 64 <720000000>;
opp-microvolt = <1200000 1176000 1224000>;
opp-supported-hw = <0x06 0x0080>;
};
oppturbo@720000000 {
opp-hz = /bits/ 64 <720000000>;
opp-microvolt = <1260000 1234800 1285200>;
opp-supported-hw = <0x01 0xFFFF>;
};
oppturbo@800000000 {
opp-hz = /bits/ 64 <800000000>;
opp-microvolt = <1260000 1234800 1285200>;
opp-supported-hw = <0x06 0x0100>;
};
oppnitro@1000000000 {
opp-hz = /bits/ 64 <1000000000>;
opp-microvolt = <1325000 1298500 1351500>;
opp-supported-hw = <0x04 0x0200>;
};
};

22
dts/Bindings/crypto/brcm,spu-crypto.txt Normal file
View File

@ -0,0 +1,22 @@
The Broadcom Secure Processing Unit (SPU) hardware supports symmetric
cryptographic offload for Broadcom SoCs. A SoC may have multiple SPU hardware
blocks.
Required properties:
- compatible: Should be one of the following:
brcm,spum-crypto - for devices with SPU-M hardware
brcm,spu2-crypto - for devices with SPU2 hardware
brcm,spu2-v2-crypto - for devices with enhanced SPU2 hardware features like SHA3
and Rabin Fingerprint support
brcm,spum-nsp-crypto - for the Northstar Plus variant of the SPU-M hardware
- reg: Should contain SPU registers location and length.
- mboxes: The mailbox channel to be used to communicate with the SPU.
Mailbox channels correspond to DMA rings on the device.
Example:
crypto@612d0000 {
compatible = "brcm,spum-crypto";
reg = <0 0x612d0000 0 0x900>;
mboxes = <&pdc0 0>;
};

27
dts/Bindings/crypto/mediatek-crypto.txt Normal file
View File

@ -0,0 +1,27 @@
MediaTek cryptographic accelerators
Required properties:
- compatible: Should be "mediatek,eip97-crypto"
- reg: Address and length of the register set for the device
- interrupts: Should contain the five crypto engines interrupts in numeric
order. These are global system and four descriptor rings.
- clocks: the clock used by the core
- clock-names: the names of the clock listed in the clocks property. These are
"ethif", "cryp"
- power-domains: Must contain a reference to the PM domain.
Example:
crypto: crypto@1b240000 {
compatible = "mediatek,eip97-crypto";
reg = <0 0x1b240000 0 0x20000>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_LOW>,
<GIC_SPI 83 IRQ_TYPE_LEVEL_LOW>,
<GIC_SPI 84 IRQ_TYPE_LEVEL_LOW>,
<GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>,
<GIC_SPI 97 IRQ_TYPE_LEVEL_LOW>;
clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
<&ethsys CLK_ETHSYS_CRYPTO>;
clock-names = "ethif","cryp";
power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>;
};

14
dts/Bindings/devfreq/exynos-bus.txt
View File

@ -123,6 +123,20 @@ Detailed correlation between sub-blocks and power line according to Exynos SoC:
|--- FSYS
|--- FSYS2
- In case of Exynos5433, there is VDD_INT power line as following:
VDD_INT |--- G2D (parent device)
|--- MSCL
|--- GSCL
|--- JPEG
|--- MFC
|--- HEVC
|--- BUS0
|--- BUS1
|--- BUS2
|--- PERIS (Fixed clock rate)
|--- PERIC (Fixed clock rate)
|--- FSYS (Fixed clock rate)
Example1:
Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
power line (regulator). The MIF (Memory Interface) AXI bus is used to

2
dts/Bindings/display/arm,pl11x.txt
View File

@ -22,7 +22,7 @@ Required properties:
- clocks: contains phandle and clock specifier pairs for the entries
in the clock-names property. See
Documentation/devicetree/binding/clock/clock-bindings.txt
Documentation/devicetree/bindings/clock/clock-bindings.txt
Optional properties:

35
dts/Bindings/display/brcm,bcm-vc4.txt
View File

@ -56,6 +56,18 @@ Required properties for V3D:
- interrupts: The interrupt number
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
Required properties for DSI:
- compatible: Should be "brcm,bcm2835-dsi0" or "brcm,bcm2835-dsi1"
- reg: Physical base address and length of the DSI block's registers
- interrupts: The interrupt number
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
- clocks: a) phy: The DSI PLL clock feeding the DSI analog PHY
b) escape: The DSI ESC clock from CPRMAN
c) pixel: The DSI pixel clock from CPRMAN
- clock-output-names:
The 3 clocks output from the DSI analog PHY: dsi[01]_byte,
dsi[01]_ddr2, and dsi[01]_ddr
[1] Documentation/devicetree/bindings/media/video-interfaces.txt
Example:
@ -99,6 +111,29 @@ dpi: dpi@7e208000 {
};
};
dsi1: dsi@7e700000 {
compatible = "brcm,bcm2835-dsi1";
reg = <0x7e700000 0x8c>;
interrupts = <2 12>;
#address-cells = <1>;
#size-cells = <0>;
#clock-cells = <1>;
clocks = <&clocks BCM2835_PLLD_DSI1>,
<&clocks BCM2835_CLOCK_DSI1E>,
<&clocks BCM2835_CLOCK_DSI1P>;
clock-names = "phy", "escape", "pixel";
clock-output-names = "dsi1_byte", "dsi1_ddr2", "dsi1_ddr";
pitouchscreen: panel@0 {
compatible = "raspberrypi,touchscreen";
reg = <0>;
<...>
};
};
vec: vec@7e806000 {
compatible = "brcm,bcm2835-vec";
reg = <0x7e806000 0x1000>;

12
dts/Bindings/display/bridge/adi,adv7511.txt
View File

@ -38,10 +38,22 @@ The following input format properties are required except in "rgb 1x" and
- adi,input-justification: The input bit justification ("left", "evenly",
"right").
- avdd-supply: A 1.8V supply that powers up the AVDD pin on the chip.
- dvdd-supply: A 1.8V supply that powers up the DVDD pin on the chip.
- pvdd-supply: A 1.8V supply that powers up the PVDD pin on the chip.
- dvdd-3v-supply: A 3.3V supply that powers up the pin called DVDD_3V
on the chip.
- bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is
needed only for ADV7511.
The following properties are required for ADV7533:
- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
be one of 1, 2, 3 or 4.
- a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip.
- v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip.
- v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be
either 1.2V or 1.8V.
Optional properties:

2
dts/Bindings/display/bridge/analogix_dp.txt
View File

@ -33,7 +33,7 @@ Optional properties for dp-controller:
in Documentation/devicetree/bindings/media/video-interfaces.txt,
please refer to the SoC specific binding document:
* Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
* Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt
* Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt
[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
-------------------------------------------------------------------------------

0
dts/Bindings/video/bridge/anx7814.txt → dts/Bindings/display/bridge/anx7814.txt
View File

71
dts/Bindings/display/bridge/dw_hdmi.txt
View File

@ -1,52 +1,33 @@
DesignWare HDMI bridge bindings
Synopsys DesignWare HDMI TX Encoder
===================================
Required properties:
- compatible: platform specific such as:
* "snps,dw-hdmi-tx"
* "fsl,imx6q-hdmi"
* "fsl,imx6dl-hdmi"
* "rockchip,rk3288-dw-hdmi"
- reg: Physical base address and length of the controller's registers.
- interrupts: The HDMI interrupt number
- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks,
as described in Documentation/devicetree/bindings/clock/clock-bindings.txt,
the clocks are soc specific, the clock-names should be "iahb", "isfr"
-port@[X]: SoC specific port nodes with endpoint definitions as defined
in Documentation/devicetree/bindings/media/video-interfaces.txt,
please refer to the SoC specific binding document:
* Documentation/devicetree/bindings/display/imx/hdmi.txt
* Documentation/devicetree/bindings/display/rockchip/dw_hdmi-rockchip.txt
This document defines device tree properties for the Synopsys DesignWare HDMI
TX Encoder (DWC HDMI TX). It doesn't constitue a device tree binding
specification by itself but is meant to be referenced by platform-specific
device tree bindings.
Optional properties
- reg-io-width: the width of the reg:1,4, default set to 1 if not present
- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing,
if the property is omitted, a functionally reduced I2C bus
controller on DW HDMI is probed
- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec"
When referenced from platform device tree bindings the properties defined in
this document are defined as follows. The platform device tree bindings are
responsible for defining whether each property is required or optional.
Example:
hdmi: hdmi@0120000 {
compatible = "fsl,imx6q-hdmi";
reg = <0x00120000 0x9000>;
interrupts = <0 115 0x04>;
gpr = <&gpr>;
clocks = <&clks 123>, <&clks 124>;
clock-names = "iahb", "isfr";
ddc-i2c-bus = <&i2c2>;
- reg: Memory mapped base address and length of the DWC HDMI TX registers.
port@0 {
reg = <0>;
- reg-io-width: Width of the registers specified by the reg property. The
value is expressed in bytes and must be equal to 1 or 4 if specified. The
register width defaults to 1 if the property is not present.
hdmi_mux_0: endpoint {
remote-endpoint = <&ipu1_di0_hdmi>;
};
};
- interrupts: Reference to the DWC HDMI TX interrupt.
port@1 {
reg = <1>;
- clocks: References to all the clocks specified in the clock-names property
as specified in Documentation/devicetree/bindings/clock/clock-bindings.txt.
hdmi_mux_1: endpoint {
remote-endpoint = <&ipu1_di1_hdmi>;
};
};
};
- clock-names: The DWC HDMI TX uses the following clocks.
- "iahb" is the bus clock for either AHB and APB (mandatory).
- "isfr" is the internal register configuration clock (mandatory).
- "cec" is the HDMI CEC controller main clock (optional).
- ports: The connectivity of the DWC HDMI TX with the rest of the system is
expressed in using ports as specified in the device graph bindings defined
in Documentation/devicetree/bindings/graph.txt. The numbering of the ports
is platform-specific.

0
dts/Bindings/video/bridge/sil-sii8620.txt → dts/Bindings/display/bridge/sil-sii8620.txt
View File

46
dts/Bindings/display/bridge/ti,ths8135.txt Normal file
View File

@ -0,0 +1,46 @@
THS8135 Video DAC
-----------------
This is the binding for Texas Instruments THS8135 Video DAC bridge.
Required properties:
- compatible: Must be "ti,ths8135"
Required nodes:
This device has two video ports. Their connections are modelled using the OF
graph bindings specified in Documentation/devicetree/bindings/graph.txt.
- Video port 0 for RGB input
- Video port 1 for VGA output
Example
-------
vga-bridge {
compatible = "ti,ths8135";
#address-cells = <1>;
#size-cells = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
vga_bridge_in: endpoint {
remote-endpoint = <&lcdc_out_vga>;
};
};
port@1 {
reg = <1>;
vga_bridge_out: endpoint {
remote-endpoint = <&vga_con_in>;
};
};
};
};

2
dts/Bindings/display/cirrus,clps711x-fb.txt
View File

@ -6,7 +6,7 @@ Required properties:
location and size of the framebuffer memory.
- clocks : phandle + clock specifier pair of the FB reference clock.
- display : phandle to a display node as described in
Documentation/devicetree/bindings/display/display-timing.txt.
Documentation/devicetree/bindings/display/panel/display-timing.txt.
Additionally, the display node has to define properties:
- bits-per-pixel: Bits per pixel.
- ac-prescale : LCD AC bias frequency. This frequency is the required

4
dts/Bindings/display/exynos/exynos7-decon.txt
View File

@ -33,12 +33,12 @@ Required properties:
- i80-if-timings: timing configuration for lcd i80 interface support.
Optional Properties:
- samsung,power-domain: a phandle to DECON power domain node.
- power-domains: a phandle to DECON power domain node.
- display-timings: timing settings for DECON, as described in document [1].
Can be used in case timings cannot be provided otherwise
or to override timings provided by the panel.
[1]: Documentation/devicetree/bindings/display/display-timing.txt
[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
Example:

2
dts/Bindings/display/exynos/samsung-fimd.txt
View File

@ -83,7 +83,7 @@ in [2]. The following are properties specific to those nodes:
3 - for parallel output,
4 - for write-back interface
[1]: Documentation/devicetree/bindings/display/display-timing.txt
[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
Example:

2
dts/Bindings/display/hisilicon/hisi-ade.txt
View File

@ -16,7 +16,7 @@ Required properties:
"clk_ade_core" for the ADE core clock.
"clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with
jpeg codec.
"clk_ade_pix" for the ADE pixel clok.
"clk_ade_pix" for the ADE pixel clock.
- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks'
phandle + clock-specifier pairs.
- assigned-clock-rates: clock rates, one for each entry in assigned-clocks.

2
dts/Bindings/display/imx/fsl,imx-fb.txt
View File

@ -9,7 +9,7 @@ Required properties:
Required nodes:
- display: Phandle to a display node as described in
Documentation/devicetree/bindings/display/display-timing.txt
Documentation/devicetree/bindings/display/panel/display-timing.txt
Additional, the display node has to define properties:
- bits-per-pixel: Bits per pixel
- fsl,pcr: LCDC PCR value

47
dts/Bindings/display/imx/hdmi.txt
View File

@ -1,29 +1,36 @@
Device-Tree bindings for HDMI Transmitter
Freescale i.MX6 DWC HDMI TX Encoder
===================================
HDMI Transmitter
================
The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
with a companion PHY IP.
These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
following device-specific properties.
The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
with accompanying PHY IP.
Required properties:
- #address-cells : should be <1>
- #size-cells : should be <0>
- compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
- gpr : should be <&gpr>.
The phandle points to the iomuxc-gpr region containing the HDMI
multiplexer control register.
- clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described
in Documentation/devicetree/bindings/clock/clock-bindings.txt and
Documentation/devicetree/bindings/clock/imx6q-clock.txt.
- port@[0-4]: Up to four port nodes with endpoint definitions as defined in
Documentation/devicetree/bindings/media/video-interfaces.txt,
corresponding to the four inputs to the HDMI multiplexer.
Optional properties:
- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- compatible : Shall be one of "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
- reg: See dw_hdmi.txt.
- interrupts: HDMI interrupt number
- clocks: See dw_hdmi.txt.
- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
- ports: See dw_hdmi.txt. The DWC HDMI shall have between one and four ports,
numbered 0 to 3, corresponding to the four inputs of the HDMI multiplexer.
Each port shall have a single endpoint.
- gpr : Shall contain a phandle to the iomuxc-gpr region containing the HDMI
multiplexer control register.
example:
Optional properties
- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master
or the functionally-reduced I2C master contained in the DWC HDMI. When
connected to a system I2C master this property contains a phandle to that
I2C master controller.
Example:
gpr: iomuxc-gpr@020e0000 {
/* ... */

2
dts/Bindings/display/imx/ldb.txt
View File

@ -64,7 +64,7 @@ Required properties:
Optional properties (required if display-timings are used):
- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- display-timings : A node that describes the display timings as defined in
Documentation/devicetree/bindings/display/display-timing.txt.
Documentation/devicetree/bindings/display/panel/display-timing.txt.
- fsl,data-mapping : should be "spwg" or "jeida"
This describes how the color bits are laid out in the
serialized LVDS signal.

2
dts/Bindings/display/mediatek/mediatek,disp.txt
View File

@ -55,7 +55,7 @@ Required properties (DMA function blocks):
"mediatek,<chip>-disp-rdma"
"mediatek,<chip>-disp-wdma"
- larb: Should contain a phandle pointing to the local arbiter device as defined
in Documentation/devicetree/bindings/soc/mediatek/mediatek,smi-larb.txt
in Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
- iommus: Should point to the respective IOMMU block with master port as
argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
for details.

2
dts/Bindings/display/msm/dsi.txt
View File

@ -108,7 +108,7 @@ Optional properties:
- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
regulator is wanted.
[1] Documentation/devicetree/bindings/clocks/clock-bindings.txt
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
[2] Documentation/devicetree/bindings/graph.txt
[3] Documentation/devicetree/bindings/media/video-interfaces.txt
[4] Documentation/devicetree/bindings/display/panel/

2
dts/Bindings/display/msm/edp.txt
View File

@ -10,7 +10,7 @@ Required properties:
- interrupts: The interrupt signal from the eDP block.
- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: device clocks
See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
- clock-names: the following clocks are required:
* "core_clk"
* "iface_clk"

38
dts/Bindings/display/msm/gpu.txt
View File

@ -1,23 +1,19 @@
Qualcomm adreno/snapdragon GPU
Required properties:
- compatible: "qcom,adreno-3xx"
- compatible: "qcom,adreno-XYZ.W", "qcom,adreno"
for example: "qcom,adreno-306.0", "qcom,adreno"
Note that you need to list the less specific "qcom,adreno" (since this
is what the device is matched on), in addition to the more specific
with the chip-id.
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt signal from the gpu.
- clocks: device clocks
See ../clocks/clock-bindings.txt for details.
- clock-names: the following clocks are required:
* "core_clk"
* "iface_clk"
* "mem_iface_clk"
- qcom,chipid: gpu chip-id. Note this may become optional for future
devices if we can reliably read the chipid from hw
- qcom,gpu-pwrlevels: list of operating points
- compatible: "qcom,gpu-pwrlevels"
- for each qcom,gpu-pwrlevel:
- qcom,gpu-freq: requested gpu clock speed
- NOTE: downstream android driver defines additional parameters to
configure memory bandwidth scaling per OPP.
* "core"
* "iface"
* "mem_iface"
Example:
@ -25,28 +21,18 @@ Example:
...
gpu: qcom,kgsl-3d0@4300000 {
compatible = "qcom,adreno-3xx";
compatible = "qcom,adreno-320.2", "qcom,adreno";
reg = <0x04300000 0x20000>;
reg-names = "kgsl_3d0_reg_memory";
interrupts = <GIC_SPI 80 0>;
interrupt-names = "kgsl_3d0_irq";
clock-names =
"core_clk",
"iface_clk",
"mem_iface_clk";
"core",
"iface",
"mem_iface";
clocks =
<&mmcc GFX3D_CLK>,
<&mmcc GFX3D_AHB_CLK>,
<&mmcc MMSS_IMEM_AHB_CLK>;
qcom,chipid = <0x03020100>;
qcom,gpu-pwrlevels {
compatible = "qcom,gpu-pwrlevels";
qcom,gpu-pwrlevel@0 {
qcom,gpu-freq = <450000000>;
};
qcom,gpu-pwrlevel@1 {
qcom,gpu-freq = <27000000>;
};
};
};
};

2
dts/Bindings/display/msm/hdmi.txt
View File

@ -49,7 +49,7 @@ Required properties:
* "hdmi_tx_l4"
- power-domains: Should be <&mmcc MDSS_GDSC>.
- clocks: device clocks
See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details.
See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
- core-vdda-supply: phandle to vdda regulator device node
Example:

27
dts/Bindings/display/multi-inno,mi0283qt.txt Normal file
View File

@ -0,0 +1,27 @@
Multi-Inno MI0283QT display panel
Required properties:
- compatible: "multi-inno,mi0283qt".
The node for this driver must be a child node of a SPI controller, hence
all mandatory properties described in ../spi/spi-bus.txt must be specified.
Optional properties:
- dc-gpios: D/C pin. The presence/absence of this GPIO determines
the panel interface mode (IM[3:0] pins):
- present: IM=x110 4-wire 8-bit data serial interface
- absent: IM=x101 3-wire 9-bit data serial interface
- reset-gpios: Reset pin
- power-supply: A regulator node for the supply voltage.
- backlight: phandle of the backlight device attached to the panel
- rotation: panel rotation in degrees counter clockwise (0,90,180,270)
Example:
mi0283qt@0{
compatible = "multi-inno,mi0283qt";
reg = <0>;
spi-max-frequency = <32000000>;
rotation = <90>;
dc-gpios = <&gpio 25 0>;
backlight = <&backlight>;
};

7
dts/Bindings/display/panel/boe,nv101wxmn51.txt Normal file
View File

@ -0,0 +1,7 @@
BOE OPTOELECTRONICS TECHNOLOGY 10.1" WXGA TFT LCD panel
Required properties:
- compatible: should be "boe,nv101wxmn51"
This binding is compatible with the simple-panel binding, which is specified
in simple-panel.txt in this directory.

7
dts/Bindings/display/panel/netron-dy,e231732.txt Normal file
View File

@ -0,0 +1,7 @@
Netron-DY E231732 7.0" WSVGA TFT LCD panel
Required properties:
- compatible: should be "netron-dy,e231732"
This binding is compatible with the simple-panel binding, which is specified
in simple-panel.txt in this directory.

2
dts/Bindings/display/panel/panel-dpi.txt
View File

@ -12,7 +12,7 @@ Optional properties:
Required nodes:
- "panel-timing" containing video timings
(Documentation/devicetree/bindings/display/display-timing.txt)
(Documentation/devicetree/bindings/display/panel/display-timing.txt)
- Video port for DPI input
Example

4
dts/Bindings/display/panel/panel.txt Normal file
View File

@ -0,0 +1,4 @@
Common display properties
-------------------------
- rotation: Display rotation in degrees counter clockwise (0,90,180,270)

2
dts/Bindings/display/panel/samsung,ld9040.txt
View File

@ -20,7 +20,7 @@ The device node can contain one 'port' child node with one child
'endpoint' node, according to the bindings defined in [3]. This
node should describe panel's video bus.
[1]: Documentation/devicetree/bindings/display/display-timing.txt
[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
[2]: Documentation/devicetree/bindings/spi/spi-bus.txt
[3]: Documentation/devicetree/bindings/media/video-interfaces.txt

2
dts/Bindings/display/panel/samsung,s6e8aa0.txt
View File

@ -21,7 +21,7 @@ The device node can contain one 'port' child node with one child
'endpoint' node, according to the bindings defined in [2]. This
node should describe panel's video bus.
[1]: Documentation/devicetree/bindings/display/display-timing.txt
[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
Example:

7
dts/Bindings/display/panel/tianma,tm070jdhg30.txt Normal file
View File

@ -0,0 +1,7 @@
Tianma Micro-electronics TM070JDHG30 7.0" WXGA TFT LCD panel
Required properties:
- compatible: should be "tianma,tm070jdhg30"
This binding is compatible with the simple-panel binding, which is specified
in simple-panel.txt in this directory.

2
dts/Bindings/display/rockchip/analogix_dp-rockchip.txt
View File

@ -35,7 +35,7 @@ Optional property for different chips:
Required elements: "grf"
For the below properties, please refer to Analogix DP binding document:
* Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
* Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
- phys (required)
- phy-names (required)
- hpd-gpios (optional)

43
dts/Bindings/display/rockchip/dw_hdmi-rockchip.txt
View File

@ -1,24 +1,39 @@
Rockchip specific extensions to the Synopsys Designware HDMI
================================
Rockchip DWC HDMI TX Encoder
============================
The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
with a companion PHY IP.
These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
following device-specific properties.
Required properties:
- compatible: "rockchip,rk3288-dw-hdmi";
- reg: Physical base address and length of the controller's registers.
- clocks: phandle to hdmi iahb and isfr clocks.
- clock-names: should be "iahb" "isfr"
- rockchip,grf: this soc should set GRF regs to mux vopl/vopb.
- compatible: Shall contain "rockchip,rk3288-dw-hdmi".
- reg: See dw_hdmi.txt.
- reg-io-width: See dw_hdmi.txt. Shall be 4.
- interrupts: HDMI interrupt number
- ports: contain a port node with endpoint definitions as defined in
Documentation/devicetree/bindings/media/video-interfaces.txt. For
vopb,set the reg = <0> and set the reg = <1> for vopl.
- reg-io-width: the width of the reg:1,4, the value should be 4 on
rk3288 platform
- clocks: See dw_hdmi.txt.
- clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
- ports: See dw_hdmi.txt. The DWC HDMI shall have a single port numbered 0
corresponding to the video input of the controller. The port shall have two
endpoints, numbered 0 and 1, connected respectively to the vopb and vopl.
- rockchip,grf: Shall reference the GRF to mux vopl/vopb.
Optional properties
- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec"
- ddc-i2c-bus: The HDMI DDC bus can be connected to either a system I2C master
or the functionally-reduced I2C master contained in the DWC HDMI. When
connected to a system I2C master this property contains a phandle to that
I2C master controller.
- clock-names: See dw_hdmi.txt. The "cec" clock is optional.
- clock-names: May contain "cec" as defined in dw_hdmi.txt.
Example:
hdmi: hdmi@ff980000 {
compatible = "rockchip,rk3288-dw-hdmi";
reg = <0xff980000 0x20000>;

5
dts/Bindings/display/ssd1307fb.txt
View File

@ -8,14 +8,15 @@ Required properties:
0x3c or 0x3d
- pwm: Should contain the pwm to use according to the OF device tree PWM
specification [0]. Only required for the ssd1307.
- reset-gpios: Should contain the GPIO used to reset the OLED display
- solomon,height: Height in pixel of the screen driven by the controller
- solomon,width: Width in pixel of the screen driven by the controller
- solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
mapped to.
Optional properties:
- reset-active-low: Is the reset gpio is active on physical low?
- reset-gpios: The GPIO used to reset the OLED display, if available. See
Documentation/devicetree/bindings/gpio/gpio.txt for details.
- vbat-supply: The supply for VBAT
- solomon,segment-no-remap: Display needs normal (non-inverted) data column
to segment mapping
- solomon,com-seq: Display uses sequential COM pin configuration

2
dts/Bindings/display/tilcdc/panel.txt
View File

@ -15,7 +15,7 @@ Required properties:
- display-timings: typical videomode of lcd panel. Multiple video modes
can be listed if the panel supports multiple timings, but the 'native-mode'
should be the preferred/default resolution. Refer to
Documentation/devicetree/bindings/display/display-timing.txt for display
Documentation/devicetree/bindings/display/panel/display-timing.txt for display
timing binding details.
Optional properties:

15
dts/Bindings/display/zte,vou.txt
View File

@ -49,6 +49,15 @@ Required properties:
"osc_clk"
"xclk"
* TV Encoder output device
Required properties:
- compatible: should be "zte,zx296718-tvenc"
- reg: Physical base address and length of the TVENC device IO region
- zte,tvenc-power-control: the phandle to SYSCTRL block followed by two
integer cells. The first cell is the offset of SYSCTRL register used
to control TV Encoder DAC power, and the second cell is the bit mask.
Example:
vou: vou@1440000 {
@ -81,4 +90,10 @@ vou: vou@1440000 {
<&topcrm HDMI_XCLK>;
clock-names = "osc_cec", "osc_clk", "xclk";
};
tvenc: tvenc@2000 {
compatible = "zte,zx296718-tvenc";
reg = <0x2000 0x1000>;
zte,tvenc-power-control = <&sysctrl 0x170 0x10>;
};
};

5
dts/Bindings/dma/stm32-dma.txt
View File

@ -40,8 +40,7 @@ Example:
DMA clients connected to the STM32 DMA controller must use the format
described in the dma.txt file, using a five-cell specifier for each
channel: a phandle plus four integer cells.
The four cells in order are:
channel: a phandle to the DMA controller plus the following four integer cells:
1. The channel id
2. The request line number
@ -61,7 +60,7 @@ The four cells in order are:
0x1: medium
0x2: high
0x3: very high
5. A 32bit mask specifying the DMA FIFO threshold configuration which are device
4. A 32bit mask specifying the DMA FIFO threshold configuration which are device
dependent:
-bit 0-1: Fifo threshold
0x0: 1/4 full FIFO

2
dts/Bindings/eeprom/eeprom.txt
View File

@ -10,6 +10,8 @@ Required properties:
"catalyst,24c32"
"microchip,24c128"
"ramtron,24c64"
"renesas,r1ex24002"

24
dts/Bindings/gpio/cortina,gemini-gpio.txt Normal file
View File

@ -0,0 +1,24 @@
Cortina Systems Gemini GPIO Controller
Required properties:
- compatible : Must be "cortina,gemini-gpio"
- reg : Should contain registers location and length
- interrupts : Should contain the interrupt line for the GPIO block
- gpio-controller : marks this as a GPIO controller
- #gpio-cells : Should be 2, see gpio/gpio.txt
- interrupt-controller : marks this as an interrupt controller
- #interrupt-cells : a standard two-cell interrupt flag, see
interrupt-controller/interrupts.txt
Example:
gpio@4d000000 {
compatible = "cortina,gemini-gpio";
reg = <0x4d000000 0x100>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};

4
dts/Bindings/gpio/gpio-pca953x.txt
View File

@ -29,6 +29,10 @@ Required properties:
onsemi,pca9654
exar,xra1202
Optional properties:
- reset-gpios: GPIO specification for the RESET input. This is an
active low signal to the PCA953x.
Example:

8
dts/Bindings/gpio/gpio.txt
View File

@ -187,10 +187,10 @@ gpio-controller's driver probe function.
Each GPIO hog definition is represented as a child node of the GPIO controller.
Required properties:
- gpio-hog: A property specifying that this child node represent a GPIO hog.
- gpios: Store the GPIO information (id, flags, ...). Shall contain the
number of cells specified in its parent node (GPIO controller
node).
- gpio-hog: A property specifying that this child node represents a GPIO hog.
- gpios: Store the GPIO information (id, flags, ...) for each GPIO to
affect. Shall contain an integer multiple of the number of cells
specified in its parent node (GPIO controller node).
Only one of the following properties scanned in the order shown below.
This means that when multiple properties are present they will be searched
in the order presented below and the first match is taken as the intended

81
dts/Bindings/gpu/arm,mali-utgard.txt Normal file
View File

@ -0,0 +1,81 @@
ARM Mali Utgard GPU
===================
Required properties:
- compatible
* Must be one of the following:
+ "arm,mali-300"
+ "arm,mali-400"
+ "arm,mali-450"
* And, optionally, one of the vendor specific compatible:
+ allwinner,sun4i-a10-mali
+ allwinner,sun7i-a20-mali
+ amlogic,meson-gxbb-mali
+ amlogic,meson-gxl-mali
+ stericsson,db8500-mali
- reg: Physical base address and length of the GPU registers
- interrupts: an entry for each entry in interrupt-names.
See ../interrupt-controller/interrupts.txt for details.
- interrupt-names:
* ppX: Pixel Processor X interrupt (X from 0 to 7)
* ppmmuX: Pixel Processor X MMU interrupt (X from 0 to 7)
* pp: Pixel Processor broadcast interrupt (mali-450 only)
* gp: Geometry Processor interrupt
* gpmmu: Geometry Processor MMU interrupt
- clocks: an entry for each entry in clock-names
- clock-names:
* bus: bus clock for the GPU
* core: clock driving the GPU itself
Optional properties:
- interrupt-names and interrupts:
* pmu: Power Management Unit interrupt, if implemented in hardware
Vendor-specific bindings
------------------------
The Mali GPU is integrated very differently from one SoC to
another. In order to accomodate those differences, you have the option
to specify one more vendor-specific compatible, among:
- allwinner,sun4i-a10-mali
Required properties:
* resets: phandle to the reset line for the GPU
- allwinner,sun7i-a20-mali
Required properties:
* resets: phandle to the reset line for the GPU
- stericsson,db8500-mali
Required properties:
* interrupt-names and interrupts:
+ combined: combined interrupt of all of the above lines
Example:
mali: gpu@1c40000 {
compatible = "allwinner,sun7i-a20-mali", "arm,mali-400";
reg = <0x01c40000 0x10000>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "gp",
"gpmmu",
"pp0",
"ppmmu0",
"pp1",
"ppmmu1",
"pmu";
clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
clock-names = "bus", "core";
resets = <&ccu RST_BUS_GPU>;
};

38
dts/Bindings/hwmon/adc128d818.txt Normal file
View File

@ -0,0 +1,38 @@
TI ADC128D818 ADC System Monitor With Temperature Sensor
--------------------------------------------------------
Operation modes:
- Mode 0: 7 single-ended voltage readings (IN0-IN6),
1 temperature reading (internal)
- Mode 1: 8 single-ended voltage readings (IN0-IN7),
no temperature
- Mode 2: 4 pseudo-differential voltage readings
(IN0-IN1, IN3-IN2, IN4-IN5, IN7-IN6),
1 temperature reading (internal)
- Mode 3: 4 single-ended voltage readings (IN0-IN3),
2 pseudo-differential voltage readings
(IN4-IN5, IN7-IN6),
1 temperature reading (internal)
If no operation mode is configured via device tree, the driver keeps the
currently active chip operation mode (default is mode 0).
Required node properties:
- compatible: must be set to "ti,adc128d818"
- reg: I2C address of the device
Optional node properties:
- ti,mode: Operation mode (see above).
Example (operation mode 2):
adc128d818@1d {
compatible = "ti,adc128d818";
reg = <0x1d>;
ti,mode = <2>;
};

1
dts/Bindings/hwmon/lm70.txt
View File

@ -4,6 +4,7 @@ Required properties:
- compatible: one of
"ti,lm70"
"ti,tmp121"
"ti,tmp122"
"ti,lm71"
"ti,lm74"

6
dts/Bindings/hwmon/lm90.txt
View File

@ -33,6 +33,11 @@ Optional properties:
LM90 "-ALERT" pin output.
See interrupt-controller/interrupts.txt for the format.
- #thermal-sensor-cells: should be set to 1. See thermal/thermal.txt for
details. See <include/dt-bindings/thermal/lm90.h> for the
definition of the local, remote and 2nd remote sensor index
constants.
Example LM90 node:
temp-sensor {
@ -41,4 +46,5 @@ temp-sensor {
vcc-supply = <&palmas_ldo6_reg>;
interrupt-parent = <&gpio>;
interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>;
#thermal-sensor-cells = <1>;
}

19
dts/Bindings/hwmon/sht15.txt Normal file
View File

@ -0,0 +1,19 @@
Sensirion SHT15 Humidity and Temperature Sensor
Required properties:
- "compatible": must be "sensirion,sht15".
- "data-gpios": GPIO connected to the data line.
- "clk-gpios": GPIO connected to the clock line.
- "vcc-supply": regulator that drives the VCC pin.
Example:
sensor {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sensor>;
compatible = "sensirion,sht15";
clk-gpios = <&gpio4 12 0>;
data-gpios = <&gpio4 13 0>;
vcc-supply = <&reg_sht15>;
};

15
dts/Bindings/hwmon/stts751.txt Normal file
View File

@ -0,0 +1,15 @@
* STTS751 thermometer.
Required node properties:
- compatible: "stts751"
- reg: I2C bus address of the device
Optional properties:
- smbus-timeout-disable: when set, the smbus timeout function will be disabled
Example stts751 node:
temp-sensor {
compatible = "stts751";
reg = <0x48>;
}

14
dts/Bindings/i2c/i2c-mux-pca954x.txt
View File

@ -19,7 +19,14 @@ Optional Properties:
- i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
children in idle state. This is necessary for example, if there are several
multiplexers on the bus and the devices behind them use same I2C addresses.
- interrupt-parent: Phandle for the interrupt controller that services
interrupts for this device.
- interrupts: Interrupt mapping for IRQ.
- interrupt-controller: Marks the device node as an interrupt controller.
- #interrupt-cells : Should be two.
- first cell is the pin number
- second cell is used to specify flags.
See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
Example:
@ -29,6 +36,11 @@ Example:
#size-cells = <0>;
reg = <0x74>;
interrupt-parent = <&ipic>;
interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <2>;
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;

1
dts/Bindings/i2c/i2c-sh_mobile.txt
View File

@ -10,6 +10,7 @@ Required properties:
- "renesas,iic-r8a7793" (R-Car M2-N)
- "renesas,iic-r8a7794" (R-Car E2)
- "renesas,iic-r8a7795" (R-Car H3)
- "renesas,iic-r8a7796" (R-Car M3-W)
- "renesas,iic-sh73a0" (SH-Mobile AG5)
- "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device)
- "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device)

33
dts/Bindings/i2c/i2c-stm32.txt Normal file
View File

@ -0,0 +1,33 @@
* I2C controller embedded in STMicroelectronics STM32 I2C platform
Required properties :
- compatible : Must be "st,stm32f4-i2c"
- reg : Offset and length of the register set for the device
- interrupts : Must contain the interrupt id for I2C event and then the
interrupt id for I2C error.
- resets: Must contain the phandle to the reset controller.
- clocks: Must contain the input clock of the I2C instance.
- A pinctrl state named "default" must be defined to set pins in mode of
operation for I2C transfer
- #address-cells = <1>;
- #size-cells = <0>;
Optional properties :
- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
the default 100 kHz frequency will be used. As only Normal and Fast modes
are supported, possible values are 100000 and 400000.
Example :
i2c@40005400 {
compatible = "st,stm32f4-i2c";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x40005400 0x400>;
interrupts = <31>,
<32>;
resets = <&rcc 277>;
clocks = <&rcc 0 149>;
pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
pinctrl-names = "default";
};

42
dts/Bindings/i2c/nvidia,tegra186-bpmp-i2c.txt Normal file
View File

@ -0,0 +1,42 @@
NVIDIA Tegra186 BPMP I2C controller
In Tegra186, the BPMP (Boot and Power Management Processor) owns certain HW
devices, such as the I2C controller for the power management I2C bus. Software
running on other CPUs must perform IPC to the BPMP in order to execute
transactions on that I2C bus. This binding describes an I2C bus that is
accessed in such a fashion.
The BPMP I2C node must be located directly inside the main BPMP node. See
../firmware/nvidia,tegra186-bpmp.txt for details of the BPMP binding.
This node represents an I2C controller. See ../i2c/i2c.txt for details of the
core I2C binding.
Required properties:
- compatible:
Array of strings.
One of:
- "nvidia,tegra186-bpmp-i2c".
- #address-cells: Address cells for I2C device address.
Single-cell integer.
Must be <1>.
- #size-cells:
Single-cell integer.
Must be <0>.
- nvidia,bpmp-bus-id:
Single-cell integer.
Indicates the I2C bus number this DT node represent, as defined by the
BPMP firmware.
Example:
bpmp {
...
i2c {
compatible = "nvidia,tegra186-bpmp-i2c";
#address-cells = <1>;
#size-cells = <0>;
nvidia,bpmp-bus-id = <5>;
};
};

1
dts/Bindings/i2c/trivial-devices.txt
View File

@ -36,6 +36,7 @@ dallas,ds1775 Tiny Digital Thermometer and Thermostat
dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM
dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O
dallas,ds75 Digital Thermometer and Thermostat
devantech,srf08 Devantech SRF08 ultrasonic ranger
dlg,da9053 DA9053: flexible system level PMIC with multicore support
dlg,da9063 DA9063: system PMIC for quad-core application processors
domintech,dmard09 DMARD09: 3-axis Accelerometer

2
dts/Bindings/iio/accel/lis302.txt
View File

@ -5,7 +5,7 @@ that apply in on the generic device (independent from the bus).
Required properties for the SPI bindings:
- compatible: should be set to "st,lis3lv02d_spi"
- compatible: should be set to "st,lis3lv02d-spi"
- reg: the chipselect index
- spi-max-frequency: maximal bus speed, should be set to 1000000 unless
constrained by external circuitry

32
dts/Bindings/iio/adc/amlogic,meson-saradc.txt Normal file
View File

@ -0,0 +1,32 @@
* Amlogic Meson SAR (Successive Approximation Register) A/D converter
Required properties:
- compatible: depending on the SoC this should be one of:
- "amlogic,meson-gxbb-saradc" for GXBB
- "amlogic,meson-gxl-saradc" for GXL
- "amlogic,meson-gxm-saradc" for GXM
along with the generic "amlogic,meson-saradc"
- reg: the physical base address and length of the registers
- clocks: phandle and clock identifier (see clock-names)
- clock-names: mandatory clocks:
- "clkin" for the reference clock (typically XTAL)
- "core" for the SAR ADC core clock
optional clocks:
- "sana" for the analog clock
- "adc_clk" for the ADC (sampling) clock
- "adc_sel" for the ADC (sampling) clock mux
- vref-supply: the regulator supply for the ADC reference voltage
- #io-channel-cells: must be 1, see ../iio-bindings.txt
Example:
saradc: adc@8680 {
compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc";
#io-channel-cells = <1>;
reg = <0x0 0x8680 0x0 0x34>;
clocks = <&xtal>,
<&clkc CLKID_SAR_ADC>,
<&clkc CLKID_SANA>,
<&clkc CLKID_SAR_ADC_CLK>,
<&clkc CLKID_SAR_ADC_SEL>;
clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel";
};

18
dts/Bindings/iio/adc/avia-hx711.txt Normal file
View File

@ -0,0 +1,18 @@
* AVIA HX711 ADC chip for weight cells
Bit-banging driver
Required properties:
- compatible: Should be "avia,hx711"
- sck-gpios: Definition of the GPIO for the clock
- dout-gpios: Definition of the GPIO for data-out
See Documentation/devicetree/bindings/gpio/gpio.txt
- avdd-supply: Definition of the regulator used as analog supply
Example:
weight@0 {
compatible = "avia,hx711";
sck-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>;
dout-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
avdd-suppy = <&avdd>;
};

18
dts/Bindings/iio/adc/max11100.txt Normal file
View File

@ -0,0 +1,18 @@
* Maxim max11100 Analog to Digital Converter (ADC)
Required properties:
- compatible: Should be "maxim,max11100"
- reg: the adc unit address
- vref-supply: phandle to the regulator that provides reference voltage
Optional properties:
- spi-max-frequency: SPI maximum frequency
Example:
max11100: adc@0 {
compatible = "maxim,max11100";
reg = <0>;
vref-supply = <&adc0_vref>;
spi-max-frequency = <240000>;
};

149
dts/Bindings/iio/adc/qcom,pm8xxx-xoadc.txt Normal file
View File

@ -0,0 +1,149 @@
Qualcomm's PM8xxx voltage XOADC
The Qualcomm PM8xxx PMICs contain a HK/XO ADC (Housekeeping/Crystal
oscillator ADC) encompassing PM8018, PM8038, PM8058 and PM8921.
Required properties:
- compatible: should be one of:
"qcom,pm8018-adc"
"qcom,pm8038-adc"
"qcom,pm8058-adc"
"qcom,pm8921-adc"
- reg: should contain the ADC base address in the PMIC, typically
0x197.
- xoadc-ref-supply: should reference a regulator that can supply
a reference voltage on demand. The reference voltage may vary
with PMIC variant but is typically something like 2.2 or 1.8V.
The following required properties are standard for IO channels, see
iio-bindings.txt for more details:
- #address-cells: should be set to <1>
- #size-cells: should be set to <0>
- #io-channel-cells: should be set to <1>
- interrupts: should refer to the parent PMIC interrupt controller
and reference the proper ADC interrupt.
Required subnodes:
The ADC channels are configured as subnodes of the ADC. Since some of
them are used for calibrating the ADC, these nodes are compulsory:
adc-channel@c {
reg = <0x0c>;
};
adc-channel@d {
reg = <0x0d>;
};
adc-channel@f {
reg = <0x0f>;
};
These three nodes are used for absolute and ratiometric calibration
and only need to have these reg values: they are by hardware definition
1:1 ratio converters that sample 625, 1250 and 0 milliV and create
an interpolation calibration for all other ADCs.
Optional subnodes: any channels other than channel 0x0c, 0x0d and
0x0f are optional.
Required channel node properties:
- reg: should contain the hardware channel number in the range
0 .. 0x0f (4 bits). The hardware only supports 16 channels.
Optional channel node properties:
- qcom,decimation:
Value type: <u32>
Definition: This parameter is used to decrease the ADC sampling rate.
Quicker measurements can be made by reducing the decimation ratio.
Valid values are 512, 1024, 2048, 4096.
If the property is not found, a default value of 512 will be used.
- qcom,ratiometric:
Value type: <u32>
Definition: Channel calibration type. If this property is specified
VADC will use a special voltage references for channel
calibration. The available references are specified in the
as a u32 value setting (see below) and it is compulsory
to also specify this reference if ratiometric calibration
is selected.
If the property is not found, the channel will be
calibrated with the 0.625V and 1.25V reference channels, also
known as an absolute calibration.
The reference voltage pairs when using ratiometric calibration:
0 = XO_IN/XOADC_GND
1 = PMIC_IN/XOADC_GND
2 = PMIC_IN/BMS_CSP
3 (invalid)
4 = XOADC_GND/XOADC_GND
5 = XOADC_VREF/XOADC_GND
Example:
xoadc: xoadc@197 {
compatible = "qcom,pm8058-adc";
reg = <0x197>;
interrupt-parent = <&pm8058>;
interrupts = <76 1>;
#address-cells = <1>;
#size-cells = <0>;
#io-channel-cells = <1>;
vcoin: adc-channel@0 {
reg = <0x00>;
};
vbat: adc-channel@1 {
reg = <0x01>;
};
dcin: adc-channel@2 {
reg = <0x02>;
};
ichg: adc-channel@3 {
reg = <0x03>;
};
vph_pwr: adc-channel@4 {
reg = <0x04>;
};
usb_vbus: adc-channel@a {
reg = <0x0a>;
};
die_temp: adc-channel@b {
reg = <0x0b>;
};
ref_625mv: adc-channel@c {
reg = <0x0c>;
};
ref_1250mv: adc-channel@d {
reg = <0x0d>;
};
ref_325mv: adc-channel@e {
reg = <0x0e>;
};
ref_muxoff: adc-channel@f {
reg = <0x0f>;
};
};
/* IIO client node */
iio-hwmon {
compatible = "iio-hwmon";
io-channels = <&xoadc 0x01>, /* Battery */
<&xoadc 0x02>, /* DC in (charger) */
<&xoadc 0x04>, /* VPH the main system voltage */
<&xoadc 0x0b>, /* Die temperature */
<&xoadc 0x0c>, /* Reference voltage 1.25V */
<&xoadc 0x0d>, /* Reference voltage 0.625V */
<&xoadc 0x0e>; /* Reference voltage 0.325V */
};

99
dts/Bindings/iio/adc/renesas,gyroadc.txt Normal file
View File

@ -0,0 +1,99 @@
* Renesas RCar GyroADC device driver
The GyroADC block is a reduced SPI block with up to 8 chipselect lines,
which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs
are sampled by the GyroADC block in a round-robin fashion and the result
presented in the GyroADC registers.
Required properties:
- compatible: Should be "<soc-specific>", "renesas,rcar-gyroadc".
The <soc-specific> should be one of:
renesas,r8a7791-gyroadc - for the GyroADC block present
in r8a7791 SoC
renesas,r8a7792-gyroadc - for the GyroADC with interrupt
block present in r8a7792 SoC
- reg: Address and length of the register set for the device
- clocks: References to all the clocks specified in the clock-names
property as specified in
Documentation/devicetree/bindings/clock/clock-bindings.txt.
- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block
clock, the "if" is the interface clock.
- power-domains: Must contain a reference to the PM domain, if available.
- #address-cells: Should be <1> (setting for the subnodes) for all ADCs
except for "fujitsu,mb88101a". Should be <0> (setting for
only subnode) for "fujitsu,mb88101a".
- #size-cells: Should be <0> (setting for the subnodes)
Sub-nodes:
You must define subnode(s) which select the connected ADC type and reference
voltage for the GyroADC channels.
Required properties for subnodes:
- compatible: Should be either of:
"fujitsu,mb88101a"
- Fujitsu MB88101A compatible mode,
12bit sampling, up to 4 channels can be sampled in
round-robin fashion. One Fujitsu chip supplies four
GyroADC channels with data as it contains four ADCs
on the chip and thus for 4-channel operation, single
MB88101A is required. The Cx chipselect lines of the
MB88101A connect directly to two CHS lines of the
GyroADC, no demuxer is required. The data out line
of each MB88101A connects to a shared input pin of
the GyroADC.
"ti,adcs7476" or "ti,adc121" or "adi,ad7476"
- TI ADCS7476 / TI ADC121 / ADI AD7476 compatible mode,
15bit sampling, up to 8 channels can be sampled in
round-robin fashion. One TI/ADI chip supplies single
ADC channel with data, thus for 8-channel operation,
8 chips are required. A 3:8 chipselect demuxer is
required to connect the nCS line of the TI/ADI chips
to the GyroADC, while MISO line of each TI/ADI ADC
connects to a shared input pin of the GyroADC.
"maxim,max1162" or "maxim,max11100"
- Maxim MAX1162 / Maxim MAX11100 compatible mode,
16bit sampling, up to 8 channels can be sampled in
round-robin fashion. One Maxim chip supplies single
ADC channel with data, thus for 8-channel operation,
8 chips are required. A 3:8 chipselect demuxer is
required to connect the nCS line of the MAX chips
to the GyroADC, while MISO line of each Maxim ADC
connects to a shared input pin of the GyroADC.
- reg: Should be the number of the analog input. Should be present
for all ADCs except "fujitsu,mb88101a".
- vref-supply: Reference to the channel reference voltage regulator.
Example:
vref_max1162: regulator-vref-max1162 {
compatible = "regulator-fixed";
regulator-name = "MAX1162 Vref";
regulator-min-microvolt = <4096000>;
regulator-max-microvolt = <4096000>;
};
adc@e6e54000 {
compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc";
reg = <0 0xe6e54000 0 64>;
clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>;
clock-names = "fck", "if";
power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
pinctrl-0 = <&adc_pins>;
pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
adc@0 {
reg = <0>;
compatible = "maxim,max1162";
vref-supply = <&vref_max1162>;
};
adc@1 {
reg = <1>;
compatible = "maxim,max1162";
vref-supply = <&vref_max1162>;
};
};

7
dts/Bindings/iio/adc/st,stm32-adc.txt
View File

@ -53,6 +53,11 @@ Required properties:
- #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in
Documentation/devicetree/bindings/iio/iio-bindings.txt
Optional properties:
- dmas: Phandle to dma channel for this ADC instance.
See ../../dma/dma.txt for details.
- dma-names: Must be "rx" when dmas property is being used.
Example:
adc: adc@40012000 {
compatible = "st,stm32f4-adc-core";
@ -77,6 +82,8 @@ Example:
interrupt-parent = <&adc>;
interrupts = <0>;
st,adc-channels = <8>;
dmas = <&dma2 0 0 0x400 0x0>;
dma-names = "rx";
};
...
other adc child nodes follow...

23
dts/Bindings/iio/adc/ti-ads7950.txt Normal file
View File

@ -0,0 +1,23 @@
* Texas Instruments ADS7950 family of A/DC chips
Required properties:
- compatible: Must be one of "ti,ads7950", "ti,ads7951", "ti,ads7952",
"ti,ads7953", "ti,ads7954", "ti,ads7955", "ti,ads7956", "ti,ads7957",
"ti,ads7958", "ti,ads7959", "ti,ads7960", or "ti,ads7961"
- reg: SPI chip select number for the device
- #io-channel-cells: Must be 1 as per ../iio-bindings.txt
- vref-supply: phandle to a regulator node that supplies the 2.5V or 5V
reference voltage
Recommended properties:
- spi-max-frequency: Definition as per
Documentation/devicetree/bindings/spi/spi-bus.txt
Example:
adc@0 {
compatible = "ti,ads7957";
reg = <0>;
#io-channel-cells = <1>;
vref-supply = <&refin_supply>;
spi-max-frequency = <10000000>;
};

36
dts/Bindings/iio/imu/bmi160.txt Normal file
View File

@ -0,0 +1,36 @@
Bosch BMI160 - Inertial Measurement Unit with Accelerometer, Gyroscope
and externally connectable Magnetometer
https://www.bosch-sensortec.com/bst/products/all_products/bmi160
Required properties:
- compatible : should be "bosch,bmi160"
- reg : the I2C address or SPI chip select number of the sensor
- spi-max-frequency : set maximum clock frequency (only for SPI)
Optional properties:
- interrupt-parent : should be the phandle of the interrupt controller
- interrupts : interrupt mapping for IRQ, must be IRQ_TYPE_LEVEL_LOW
- interrupt-names : set to "INT1" if INT1 pin should be used as interrupt
input, set to "INT2" if INT2 pin should be used instead
Examples:
bmi160@68 {
compatible = "bosch,bmi160";
reg = <0x68>;
interrupt-parent = <&gpio4>;
interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
interrupt-names = "INT1";
};
bmi160@0 {
compatible = "bosch,bmi160";
reg = <0>;
spi-max-frequency = <10000000>;
interrupt-parent = <&gpio2>;
interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
interrupt-names = "INT2";
};

26
dts/Bindings/iio/imu/st_lsm6dsx.txt Normal file
View File

@ -0,0 +1,26 @@
* ST_LSM6DSx driver for STM 6-axis (acc + gyro) imu Mems sensors
Required properties:
- compatible: must be one of:
"st,lsm6ds3"
"st,lsm6dsm"
- reg: i2c address of the sensor / spi cs line
Optional properties:
- st,drdy-int-pin: the pin on the package that will be used to signal
"data ready" (valid values: 1 or 2).
- interrupt-parent: should be the phandle for the interrupt controller
- interrupts: interrupt mapping for IRQ. It should be configured with
flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING.
Refer to interrupt-controller/interrupts.txt for generic interrupt
client node bindings.
Example:
lsm6dsm@6b {
compatible = "st,lsm6dsm";
reg = <0x6b>;
interrupt-parent = <&gpio0>;
interrupts = <0 IRQ_TYPE_EDGE_RISING>;
};

41
dts/Bindings/iio/light/cm3605.txt Normal file
View File

@ -0,0 +1,41 @@
Capella Microsystems CM3605
Ambient Light and Short Distance Proximity Sensor
The CM3605 is an entirely analog part which however require quite a bit of
software logic to interface a host operating system.
This ALS and proximity sensor was one of the very first deployed in mobile
handsets, notably it is used in the very first Nexus One Android phone from
2010.
Required properties:
- compatible: must be: "capella,cm3605"
- aset-gpios: GPIO line controlling the ASET line (drive low
to activate the ALS, should be flagged GPIO_ACTIVE_LOW)
- interrupts: the IRQ line (such as a GPIO) that is connected to
the POUT (proximity sensor out) line. The edge detection must
be set to IRQ_TYPE_EDGE_BOTH so as to detect movements toward
and away from the proximity sensor.
- io-channels: the ADC channel used for converting the voltage from
AOUT to a digital representation.
- io-channel-names: must be "aout"
Optional properties:
- vdd-supply: regulator supplying VDD power to the component.
- capella,aset-resistance-ohms: the sensitivity calibration resistance,
in Ohms. Valid values are: 50000, 100000, 300000 and 600000,
as these are the resistance values that we are supplied with
calibration curves for. If not supplied, 100 kOhm will be assumed
but it is strongly recommended to supply this.
Example:
cm3605 {
compatible = "capella,cm3605";
vdd-supply = <&foo_reg>;
aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>;
capella,aset-resistance-ohms = <100000>;
interrupts = <1 IRQ_TYPE_EDGE_BOTH>;
io-channels = <&adc 0x01>;
io-channel-names = "aout";
};

23
dts/Bindings/iio/potentiometer/max5481.txt Normal file
View File

@ -0,0 +1,23 @@
* Maxim Linear-Taper Digital Potentiometer MAX5481-MAX5484
The node for this driver must be a child node of a SPI controller, hence
all mandatory properties described in
Documentation/devicetree/bindings/spi/spi-bus.txt
must be specified.
Required properties:
- compatible: Must be one of the following, depending on the
model:
"maxim,max5481"
"maxim,max5482"
"maxim,max5483"
"maxim,max5484"
Example:
max548x: max548x@0 {
compatible = "maxim,max5482";
spi-max-frequency = <7000000>;
reg = <0>; /* chip-select */
};

2
dts/Bindings/iio/st-sensors.txt
View File

@ -27,6 +27,8 @@ standard bindings from pinctrl/pinctrl-bindings.txt.
Valid compatible strings:
Accelerometers:
- st,lis3lv02d (deprecated, use st,lis3lv02dl-accel)
- st,lis302dl-spi (deprecated, use st,lis3lv02dl-accel)
- st,lis3lv02dl-accel
- st,lsm303dlh-accel
- st,lsm303dlhc-accel

35
dts/Bindings/iio/temperature/tmp007.txt Normal file
View File

@ -0,0 +1,35 @@
* TI TMP007 - IR thermopile sensor with integrated math engine
Link to datasheet: http://www.ti.com/lit/ds/symlink/tmp007.pdf
Required properties:
- compatible: should be "ti,tmp007"
- reg: the I2C address of the sensor (changeable via ADR pins)
------------------------------
|ADR1 | ADR0 | Device Address|
------------------------------
0 0 0x40
0 1 0x41
0 SDA 0x42
0 SCL 0x43
1 0 0x44
1 1 0x45
1 SDA 0x46
1 SCL 0x47
Optional properties:
- interrupt-parent: should be the phandle for the interrupt controller
- interrupts: interrupt mapping for GPIO IRQ (level active low)
Example:
tmp007@40 {
compatible = "ti,tmp007";
reg = <0x40>;
interrupt-parent = <&gpio0>;
interrupts = <5 0x08>;
};

Some files were not shown because too many files have changed in this diff Show More