diff --git a/CHANGELOG b/CHANGELOG index ef42071a3..064bf867b 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,13 @@ Changes since U-Boot 1.0.0: ====================================================================== +* Make BMS2003 use a separate config file to avoid #ifdef mess; + add I2C support; add support for DS1337 RTC + +* Add CompactFlash support for BMS2003 board + +* Add support for status LED on BMS2003 board + * Patch by Scott McNutt, 02 Jan 2004: Add support for the Nios Active Serial Memory Interface (ASMI) on Cyclone devices diff --git a/Makefile b/Makefile index 126c9e9d9..706216300 100644 --- a/Makefile +++ b/Makefile @@ -261,10 +261,7 @@ AMX860_config : unconfig @./mkconfig $(@:_config=) ppc mpc8xx amx860 westel bms2003_config : unconfig - @echo "#define CONFIG_BMS2003" >include/config.h - @echo "#define CONFIG_LCD" >>include/config.h - @echo "#define CONFIG_NEC_NL6448BC33_54" >>include/config.h - @./mkconfig -a TQM823L ppc mpc8xx tqm8xx + @./mkconfig $(@:_config=) ppc mpc8xx tqm8xx c2mon_config: unconfig @./mkconfig $(@:_config=) ppc mpc8xx c2mon diff --git a/board/dbau1x00/dbau1x00.c b/board/dbau1x00/dbau1x00.c index 8fcbd812a..315e41260 100644 --- a/board/dbau1x00/dbau1x00.c +++ b/board/dbau1x00/dbau1x00.c @@ -39,13 +39,6 @@ long int initdram(int board_type) /* In cpu/mips/cpu.c */ void write_one_tlb( int index, u32 pagemask, u32 hi, u32 low0, u32 low1 ); -#ifdef CONFIG_DBAU1100 -#warning "FIXME Check that bcsr is the same as dbau1000 board!" -#endif -#ifdef CONFIG_DBAU1500 -#warning "FIXME Check that bcsr is the same as dbau1000 board!" -#endif - int checkboard (void) { u16 status; diff --git a/common/cmd_ide.c b/common/cmd_ide.c index 331041c16..668d838af 100644 --- a/common/cmd_ide.c +++ b/common/cmd_ide.c @@ -835,6 +835,7 @@ output_data_short(int dev, ulong *sect_buf, int words) static void input_swap_data(int dev, ulong *sect_buf, int words) { +#ifndef CONFIG_BMS2003 volatile ushort *pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG); ushort *dbuf = (ushort *)sect_buf; @@ -842,6 +843,20 @@ input_swap_data(int dev, ulong *sect_buf, int words) *dbuf++ = ld_le16(pbuf); *dbuf++ = ld_le16(pbuf); } +#else /* CONFIG_BMS2003 */ + uchar i; + volatile uchar *pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN); + volatile uchar *pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD); + ushort *dbuf = (ushort *)sect_buf; + + while (words--) { + for (i=0; i<2; i++) { + *(((uchar *)(dbuf)) + 1) = *pbuf_even; + *(uchar *)dbuf = *pbuf_odd; + dbuf+=1; + } + } +#endif /* CONFIG_BMS2003 */ } #endif /* __LITTLE_ENDIAN || CONFIG_AU1X00 */ @@ -850,6 +865,7 @@ input_swap_data(int dev, ulong *sect_buf, int words) static void output_data(int dev, ulong *sect_buf, int words) { +#ifndef CONFIG_BMS2003 ushort *dbuf; volatile ushort *pbuf; @@ -861,6 +877,25 @@ output_data(int dev, ulong *sect_buf, int words) __asm__ volatile ("eieio"); *pbuf = *dbuf++; } +#else /* CONFIG_BMS2003 */ + uchar *dbuf; + volatile uchar *pbuf_even; + volatile uchar *pbuf_odd; + + pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN); + pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD); + dbuf = (uchar *)sect_buf; + while (words--) { + __asm__ volatile ("eieio"); + *pbuf_even = *dbuf++; + __asm__ volatile ("eieio"); + *pbuf_odd = *dbuf++; + __asm__ volatile ("eieio"); + *pbuf_even = *dbuf++; + __asm__ volatile ("eieio"); + *pbuf_odd = *dbuf++; + } +#endif /* CONFIG_BMS2003 */ } #else /* ! __PPC__ */ static void @@ -874,6 +909,7 @@ output_data(int dev, ulong *sect_buf, int words) static void input_data(int dev, ulong *sect_buf, int words) { +#ifndef CONFIG_BMS2003 ushort *dbuf; volatile ushort *pbuf; @@ -885,6 +921,25 @@ input_data(int dev, ulong *sect_buf, int words) __asm__ volatile ("eieio"); *dbuf++ = *pbuf; } +#else /* CONFIG_BMS2003 */ + uchar *dbuf; + volatile uchar *pbuf_even; + volatile uchar *pbuf_odd; + + pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN); + pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD); + dbuf = (uchar *)sect_buf; + while (words--) { + __asm__ volatile ("eieio"); + *dbuf++ = *pbuf_even; + __asm__ volatile ("eieio"); + *dbuf++ = *pbuf_odd; + __asm__ volatile ("eieio"); + *dbuf++ = *pbuf_even; + __asm__ volatile ("eieio"); + *dbuf++ = *pbuf_odd; + } +#endif /* CONFIG_BMS2003 */ } #else /* ! __PPC__ */ static void @@ -1409,6 +1464,7 @@ static void ide_led (uchar led, uchar status) static void output_data_shorts(int dev, ushort *sect_buf, int shorts) { +#ifndef CONFIG_BMS2003 ushort *dbuf; volatile ushort *pbuf; @@ -1418,11 +1474,26 @@ output_data_shorts(int dev, ushort *sect_buf, int shorts) __asm__ volatile ("eieio"); *pbuf = *dbuf++; } +#else /* CONFIG_BMS2003 */ + uchar *dbuf; + volatile uchar *pbuf_even; + volatile uchar *pbuf_odd; + + pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN); + pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD); + while (shorts--) { + __asm__ volatile ("eieio"); + *pbuf_even = *dbuf++; + __asm__ volatile ("eieio"); + *pbuf_odd = *dbuf++; + } +#endif /* CONFIG_BMS2003 */ } static void input_data_shorts(int dev, ushort *sect_buf, int shorts) { +#ifndef CONFIG_BMS2003 ushort *dbuf; volatile ushort *pbuf; @@ -1432,6 +1503,20 @@ input_data_shorts(int dev, ushort *sect_buf, int shorts) __asm__ volatile ("eieio"); *dbuf++ = *pbuf; } +#else /* CONFIG_BMS2003 */ + uchar *dbuf; + volatile uchar *pbuf_even; + volatile uchar *pbuf_odd; + + pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN); + pbuf_odd = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD); + while (shorts--) { + __asm__ volatile ("eieio"); + *dbuf++ = *pbuf_even; + __asm__ volatile ("eieio"); + *dbuf++ = *pbuf_odd; + } +#endif /* CONFIG_BMS2003 */ } #else /* ! __PPC__ */ diff --git a/common/cmd_pcmcia.c b/common/cmd_pcmcia.c index 1bd4bc532..8c17859da 100644 --- a/common/cmd_pcmcia.c +++ b/common/cmd_pcmcia.c @@ -229,7 +229,7 @@ int pcmcia_on (void) #endif /* CONFIG_IDE_8xx_PCCARD */ #ifdef CONFIG_BMS2003 case 3: { /* map I/O window for 4xUART data/ctrl */ - win->br += 0x140000; + win->br += 0x40000; win->or = ( PCMCIA_BSIZE_256K | PCMCIA_PPS_8 | PCMCIA_PRS_IO @@ -622,6 +622,7 @@ static int hardware_enable(int slot) PCMCIA_PGCRX(slot) = reg; udelay(500); +#ifndef CONFIG_BMS2003 #ifndef CONFIG_NSCU /* * Configure Port C pins for @@ -633,6 +634,16 @@ static int hardware_enable(int slot) immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004); #endif +#else /* CONFIG_BMS2003 */ + /* + * Configure Port B pins for + * 5 Volts Enable and 3 Volts enable + */ + immap->im_cpm.cp_pbpar &= ~(0x00000300); + + /* remove all power */ + immap->im_cpm.cp_pbdat |= 0x00000300; +#endif /* CONFIG_BMS2003 */ /* * Make sure there is a card in the slot, then configure the interface. @@ -641,7 +652,11 @@ static int hardware_enable(int slot) debug ("[%d] %s: PIPR(%p)=0x%x\n", __LINE__,__FUNCTION__, &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); +#ifndef CONFIG_BMS2003 if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) { +#else + if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) { +#endif /* CONFIG_BMS2003 */ printf (" No Card found\n"); return (1); } @@ -657,13 +672,25 @@ static int hardware_enable(int slot) (reg&PCMCIA_VS2(slot))?"n":"ff"); #ifndef CONFIG_NSCU if ((reg & mask) == mask) { +#ifndef CONFIG_BMS2003 immap->im_ioport.iop_pcdat |= 0x0004; +#else + immap->im_cpm.cp_pbdat &= ~(0x0000100); +#endif /* CONFIG_BMS2003 */ puts (" 5.0V card found: "); } else { +#ifndef CONFIG_BMS2003 immap->im_ioport.iop_pcdat |= 0x0002; +#else + immap->im_cpm.cp_pbdat &= ~(0x0000200); +#endif /* CONFIG_BMS2003 */ puts (" 3.3V card found: "); } +#ifndef CONFIG_BMS2003 immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004); +#else + immap->im_cpm.cp_pbdir |= 0x00000300; +#endif /* CONFIG_BMS2003 */ #else if ((reg & mask) == mask) { puts (" 5.0V card found: "); @@ -708,10 +735,14 @@ static int hardware_disable(int slot) immap = (immap_t *)CFG_IMMR; pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia)); +#ifndef CONFIG_BMS2003 #ifndef CONFIG_NSCU /* remove all power */ immap->im_ioport.iop_pcdat &= ~(0x0002 | 0x0004); #endif +#else /* CONFIG_BMS2003 */ + immap->im_cpm.cp_pbdat |= 0x00000300; +#endif /* CONFIG_BMS2003 */ debug ("Disable PCMCIA buffers and assert RESET\n"); reg = 0; @@ -761,6 +792,7 @@ static int voltage_set(int slot, int vcc, int vpp) PCMCIA_PGCRX(slot) = reg; udelay(500); +#ifndef CONFIG_BMS2003 /* * Configure Port C pins for * 5 Volts Enable and 3 Volts enable, @@ -778,6 +810,26 @@ static int voltage_set(int slot, int vcc, int vpp) case 50: reg |= 0x0004; break; default: goto done; } +#else /* CONFIG_BMS2003 */ + /* + * Configure Port B pins for + * 5 Volts Enable and 3 Volts enable, + * Turn off all power + */ + debug ("PCMCIA power OFF\n"); + immap->im_cpm.cp_pbpar &= ~(0x00000300); + /* remove all power */ + + immap->im_cpm.cp_pbdat |= 0x00000300; + + reg = 0; + switch(vcc) { + case 0: break; + case 33: reg |= 0x00000200; break; + case 50: reg |= 0x00000100; break; + default: goto done; +} +#endif /* CONFIG_BMS2003 */ /* Checking supported voltages */ @@ -785,11 +837,21 @@ static int voltage_set(int slot, int vcc, int vpp) pcmp->pcmc_pipr, (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V"); +#ifndef CONFIG_BMS2003 immap->im_ioport.iop_pcdat |= reg; immap->im_ioport.iop_pcdir |= (0x0002 | 0x0004); +#else + immap->im_cpm.cp_pbdat &= !reg; + immap->im_cpm.cp_pbdir |= 0x00000300; +#endif /* CONFIG_BMS2003 */ if (reg) { +#ifndef CONFIG_BMS2003 debug ("PCMCIA powered at %sV\n", (reg&0x0004) ? "5.0" : "3.3"); +#else + debug ("PCMCIA powered at %sV\n", + (reg&0x00000200) ? "5.0" : "3.3"); +#endif /* CONFIG_BMS2003 */ } else { debug ("PCMCIA powered down\n"); } @@ -1774,7 +1836,11 @@ static int hardware_enable (int slot) debug ("[%d] %s: PIPR(%p)=0x%x\n", __LINE__,__FUNCTION__, &(pcmp->pcmc_pipr),pcmp->pcmc_pipr); +#ifndef CONFIG_BMS2003 if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) { +#else + if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) { +#endif /* CONFIG_BMS2003 */ printf (" No Card found\n"); return (1); } diff --git a/include/asm-mips/au1x00.h b/include/asm-mips/au1x00.h index 917fd83ae..317e6daae 100644 --- a/include/asm-mips/au1x00.h +++ b/include/asm-mips/au1x00.h @@ -128,6 +128,9 @@ static __inline__ int au_ffs(int x) #define ALLINTS (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4 | IE_IRQ5) #endif +#define CP0_IWATCHLO $18,1 +#define CP0_DEBUG $23 + /* SDRAM Controller */ #define MEM_SDMODE0 0xB4000000 #define MEM_SDMODE1 0xB4000004 diff --git a/include/ata.h b/include/ata.h index fa30ee8bd..719f76a2f 100644 --- a/include/ata.h +++ b/include/ata.h @@ -56,6 +56,8 @@ #define ATA_CYL_HIGH ATA_IO_REG(5) #define ATA_DEV_HD ATA_IO_REG(6) #define ATA_COMMAND ATA_IO_REG(7) +#define ATA_DATA_EVEN ATA_IO_REG(8) +#define ATA_DATA_ODD ATA_IO_REG(9) #define ATA_STATUS ATA_COMMAND #define ATA_DEV_CTL ATA_IO_ALT(6) #define ATA_LBA_LOW ATA_SECT_NUM diff --git a/include/configs/TQM823L.h b/include/configs/TQM823L.h index 020cc8312..b62095fec 100644 --- a/include/configs/TQM823L.h +++ b/include/configs/TQM823L.h @@ -80,17 +80,13 @@ #undef CONFIG_WATCHDOG /* watchdog disabled */ -#ifdef CONFIG_LCD +#if defined(CONFIG_LCD) # undef CONFIG_STATUS_LED /* disturbs display */ #else # define CONFIG_STATUS_LED 1 /* Status LED enabled */ #endif /* CONFIG_LCD */ -#ifdef CONFIG_BMS2003 -# define CONFIG_CAN_DRIVER 1 /* CAN Driver support enabled */ -#else -# undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ -#endif +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ #define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) diff --git a/include/configs/bms2003.h b/include/configs/bms2003.h new file mode 100644 index 000000000..c5d5d88d0 --- /dev/null +++ b/include/configs/bms2003.h @@ -0,0 +1,515 @@ +/* + * (C) Copyright 2000-2003 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_BMS2003 +#define CONFIG_MPC823 1 /* This is a MPC823 CPU */ +#define CONFIG_TQM823L 1 /* ...on a TQM8xxL module */ + +#define CONFIG_LCD +#define CONFIG_NEC_NL6448BC33_54 /* NEC NL6448BC33_54 display */ + +#ifdef CONFIG_LCD /* with LCD controller ? */ +#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/ +#endif + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ + +#define CONFIG_BOOTCOUNT_LIMIT + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_BOARD_TYPES 1 /* support board types */ + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname):$(netdev):off panic=1\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \ + "rootpath=/opt/eldk/ppc_8xx\0" \ + "bootfile=/tftpboot/TQM860L/uImage\0" \ + "kernel_addr=40040000\0" \ + "ramdisk_addr=40100000\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ + +#define CFG_I2C_SPEED 40000 /* 40 kHz is supposed to work */ +#define CFG_I2C_SLAVE 0xFE + +/* Software (bit-bang) I2C driver configuration */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ + else immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ + else immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ + +#define CONFIG_CAN_DRIVER 1 /* CAN Driver support enabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION + +#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +#ifdef CONFIG_SPLASH_SCREEN +# define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_BMP | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_I2C | \ + CFG_CMD_IDE ) +#else +# define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_I2C | \ + CFG_CMD_IDE ) +#endif + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if 0 +#define CFG_HUSH_PARSER 1 /* use "hush" command parser */ +#endif +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFFF00000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * Hardware Information Block + */ +#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ +#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */ +#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)! + */ +#ifdef CONFIG_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */ +#define CFG_PLPRCR \ + ( (5-1)< ms + * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + * -------------------------------------------- + * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 + * + * 50 MHz => 50.000.000 / Divider = 98 + * 66 Mhz => 66.000.000 / Divider = 129 + * 80 Mhz => 80.000.000 / Divider = 156 + */ +#if defined(CONFIG_80MHz) +#define CFG_MAMR_PTA 156 +#elif defined(CONFIG_66MHz) +#define CFG_MAMR_PTA 129 +#else /* 50 MHz */ +#define CFG_MAMR_PTA 98 +#endif /*CONFIG_??MHz */ + +/* + * For 16 MBit, refresh rates could be 31.3 us + * (= 64 ms / 2K = 125 / quad bursts). + * For a simpler initialization, 15.6 us is used instead. + * + * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks + * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank + */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ diff --git a/include/status_led.h b/include/status_led.h index 47f7c355a..3438bde32 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -43,7 +43,7 @@ void status_led_tick (unsigned long timestamp); void status_led_set (int led, int state); /***** TQM8xxL ********************************************************/ -#if defined(CONFIG_TQM8xxL) +#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_BMS2003) # define STATUS_LED_PAR im_cpm.cp_pbpar # define STATUS_LED_DIR im_cpm.cp_pbdir # define STATUS_LED_ODR im_cpm.cp_pbodr @@ -318,6 +318,21 @@ void status_led_set (int led, int state); # define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ +/***** BMS2003 ********************************************************/ +#elif defined(CONFIG_BMS2003) +# define STATUS_LED_PAR im_ioport.iop_papar +# define STATUS_LED_DIR im_ioport.iop_padir +# define STATUS_LED_ODR im_ioport.iop_paodr +# define STATUS_LED_DAT im_ioport.iop_padat + +# define STATUS_LED_BIT 0x00000001 /* LED is on PA15 */ +# define STATUS_LED_PERIOD (CFG_HZ / 2) +# define STATUS_LED_STATE STATUS_LED_BLINKING + +# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ + +# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + /************************************************************************/ #else # error Status LED configuration missing