285 lines
6.4 KiB
C
285 lines
6.4 KiB
C
/*
|
|
* Copyright (C) 2007 Sascha Hauer, Pengutronix
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
*
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <net.h>
|
|
#include <init.h>
|
|
#include <environment.h>
|
|
#include <fec.h>
|
|
#include <asm/armlinux.h>
|
|
#include <generated/mach-types.h>
|
|
#include <partition.h>
|
|
#include <fs.h>
|
|
#include <fcntl.h>
|
|
#include <io.h>
|
|
#include <asm/hardware.h>
|
|
#include <nand.h>
|
|
#include <sizes.h>
|
|
#include <linux/mtd/nand.h>
|
|
#include <mach/board.h>
|
|
#include <mach/at91sam9_smc.h>
|
|
#include <mach/sam9_smc.h>
|
|
#include <gpio.h>
|
|
#include <mach/io.h>
|
|
#include <mach/at91_pmc.h>
|
|
#include <mach/at91_rstc.h>
|
|
|
|
/*
|
|
* board revision encoding
|
|
* bit 0:
|
|
* 0 => 1 mmc
|
|
* 1 => 2 mmcs (board from revision C)
|
|
*/
|
|
#define HAVE_2MMC (1 << 0)
|
|
static void ek_set_board_type(void)
|
|
{
|
|
if (machine_is_at91sam9g20ek()) {
|
|
armlinux_set_architecture(MACH_TYPE_AT91SAM9G20EK);
|
|
#ifdef CONFIG_AT91_HAVE_2MMC
|
|
armlinux_set_revision(HAVE_2MMC);
|
|
#endif
|
|
} else {
|
|
armlinux_set_architecture(MACH_TYPE_AT91SAM9260EK);
|
|
}
|
|
}
|
|
|
|
static struct atmel_nand_data nand_pdata = {
|
|
.ale = 21,
|
|
.cle = 22,
|
|
.det_pin = -EINVAL,
|
|
.rdy_pin = AT91_PIN_PC13,
|
|
.enable_pin = AT91_PIN_PC14,
|
|
#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
|
|
.bus_width_16 = 1,
|
|
#else
|
|
.bus_width_16 = 0,
|
|
#endif
|
|
.on_flash_bbt = 1,
|
|
};
|
|
|
|
static struct sam9_smc_config ek_9260_nand_smc_config = {
|
|
.ncs_read_setup = 0,
|
|
.nrd_setup = 1,
|
|
.ncs_write_setup = 0,
|
|
.nwe_setup = 1,
|
|
|
|
.ncs_read_pulse = 3,
|
|
.nrd_pulse = 3,
|
|
.ncs_write_pulse = 3,
|
|
.nwe_pulse = 3,
|
|
|
|
.read_cycle = 5,
|
|
.write_cycle = 5,
|
|
|
|
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
|
|
.tdf_cycles = 2,
|
|
};
|
|
|
|
static struct sam9_smc_config ek_9g20_nand_smc_config = {
|
|
.ncs_read_setup = 0,
|
|
.nrd_setup = 2,
|
|
.ncs_write_setup = 0,
|
|
.nwe_setup = 2,
|
|
|
|
.ncs_read_pulse = 4,
|
|
.nrd_pulse = 4,
|
|
.ncs_write_pulse = 4,
|
|
.nwe_pulse = 4,
|
|
|
|
.read_cycle = 7,
|
|
.write_cycle = 7,
|
|
|
|
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
|
|
.tdf_cycles = 3,
|
|
};
|
|
|
|
static void ek_add_device_nand(void)
|
|
{
|
|
struct sam9_smc_config *smc;
|
|
|
|
if (machine_is_at91sam9g20ek())
|
|
smc = &ek_9g20_nand_smc_config;
|
|
else
|
|
smc = &ek_9260_nand_smc_config;
|
|
|
|
/* setup bus-width (8 or 16) */
|
|
if (nand_pdata.bus_width_16)
|
|
smc->mode |= AT91_SMC_DBW_16;
|
|
else
|
|
smc->mode |= AT91_SMC_DBW_8;
|
|
|
|
/* configure chip-select 3 (NAND) */
|
|
sam9_smc_configure(3, smc);
|
|
|
|
at91_add_device_nand(&nand_pdata);
|
|
}
|
|
|
|
static struct at91_ether_platform_data macb_pdata = {
|
|
.is_rmii = 1,
|
|
.phy_addr = 0,
|
|
};
|
|
|
|
static void at91sam9260ek_phy_reset(void)
|
|
{
|
|
unsigned long rstc;
|
|
at91_pmc_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC);
|
|
|
|
at91_set_gpio_input(AT91_PIN_PA14, 0);
|
|
at91_set_gpio_input(AT91_PIN_PA15, 0);
|
|
at91_set_gpio_input(AT91_PIN_PA17, 0);
|
|
at91_set_gpio_input(AT91_PIN_PA25, 0);
|
|
at91_set_gpio_input(AT91_PIN_PA26, 0);
|
|
at91_set_gpio_input(AT91_PIN_PA28, 0);
|
|
|
|
rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
|
|
|
|
/* Need to reset PHY -> 500ms reset */
|
|
at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
|
|
(AT91_RSTC_ERSTL & (0x0d << 8)) |
|
|
AT91_RSTC_URSTEN);
|
|
|
|
at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
|
|
|
|
/* Wait for end hardware reset */
|
|
while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
|
|
|
|
/* Restore NRST value */
|
|
at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
|
|
(rstc) |
|
|
AT91_RSTC_URSTEN);
|
|
}
|
|
|
|
/*
|
|
* MCI (SD/MMC)
|
|
*/
|
|
#if defined(CONFIG_MCI_ATMEL)
|
|
static struct atmel_mci_platform_data __initdata ek_mci_data = {
|
|
.bus_width = 4,
|
|
.slot_b = 1,
|
|
};
|
|
|
|
static void ek_usb_add_device_mci(void)
|
|
{
|
|
if (machine_is_at91sam9g20ek())
|
|
ek_mci_data.detect_pin = AT91_PIN_PC9;
|
|
|
|
at91_add_device_mci(0, &ek_mci_data);
|
|
}
|
|
#else
|
|
static void ek_usb_add_device_mci(void) {}
|
|
#endif
|
|
|
|
/*
|
|
* USB Host port
|
|
*/
|
|
static struct at91_usbh_data __initdata ek_usbh_data = {
|
|
.ports = 2,
|
|
.vbus_pin = { -EINVAL, -EINVAL },
|
|
};
|
|
|
|
/*
|
|
* USB Device port
|
|
*/
|
|
static struct at91_udc_data __initdata ek_udc_data = {
|
|
.vbus_pin = AT91_PIN_PC5,
|
|
.pullup_pin = -EINVAL, /* pull-up driven by UDC */
|
|
};
|
|
|
|
struct gpio_led leds[] = {
|
|
{
|
|
.gpio = AT91_PIN_PA6,
|
|
.active_low = 1,
|
|
.led = {
|
|
.name = "ds5",
|
|
},
|
|
}, {
|
|
.gpio = AT91_PIN_PA9,
|
|
.led = {
|
|
.name = "ds3",
|
|
},
|
|
},
|
|
};
|
|
|
|
static void __init ek_add_led(void)
|
|
{
|
|
int i;
|
|
|
|
#ifdef CONFIG_AT91_HAVE_2MMC
|
|
leds[0].gpio = AT91_PIN_PB8;
|
|
leds[1].gpio = AT91_PIN_PB9;
|
|
#endif
|
|
|
|
for (i = 0; i < ARRAY_SIZE(leds); i++) {
|
|
at91_set_gpio_output(leds[i].gpio, leds[i].active_low);
|
|
led_gpio_register(&leds[i]);
|
|
}
|
|
led_set_trigger(LED_TRIGGER_HEARTBEAT, &leds[1].led);
|
|
}
|
|
|
|
static int at91sam9260ek_mem_init(void)
|
|
{
|
|
at91_add_device_sdram(0);
|
|
|
|
return 0;
|
|
}
|
|
mem_initcall(at91sam9260ek_mem_init);
|
|
|
|
static void __init ek_add_device_buttons(void)
|
|
{
|
|
at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */
|
|
at91_set_deglitch(AT91_PIN_PA30, 1);
|
|
export_env_ull("dfu_button", AT91_PIN_PA30);
|
|
at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */
|
|
at91_set_deglitch(AT91_PIN_PA31, 1);
|
|
export_env_ull("btn4", AT91_PIN_PA31);
|
|
}
|
|
|
|
static int at91sam9260ek_devices_init(void)
|
|
{
|
|
ek_add_device_nand();
|
|
at91sam9260ek_phy_reset();
|
|
at91_add_device_eth(0, &macb_pdata);
|
|
at91_add_device_usbh_ohci(&ek_usbh_data);
|
|
at91_add_device_udc(&ek_udc_data);
|
|
ek_usb_add_device_mci();
|
|
ek_add_device_buttons();
|
|
ek_add_led();
|
|
|
|
armlinux_set_bootparams((void *)(AT91_CHIPSELECT_1 + 0x100));
|
|
ek_set_board_type();
|
|
|
|
devfs_add_partition("nand0", 0x00000, SZ_128K, DEVFS_PARTITION_FIXED, "at91bootstrap_raw");
|
|
dev_add_bb_dev("at91bootstrap_raw", "at91bootstrap");
|
|
devfs_add_partition("nand0", SZ_128K, SZ_256K, DEVFS_PARTITION_FIXED, "self_raw");
|
|
dev_add_bb_dev("self_raw", "self0");
|
|
devfs_add_partition("nand0", SZ_256K + SZ_128K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw");
|
|
dev_add_bb_dev("env_raw", "env0");
|
|
devfs_add_partition("nand0", SZ_512K, SZ_128K, DEVFS_PARTITION_FIXED, "env_raw1");
|
|
dev_add_bb_dev("env_raw1", "env1");
|
|
|
|
return 0;
|
|
}
|
|
|
|
device_initcall(at91sam9260ek_devices_init);
|
|
|
|
static int at91sam9260ek_console_init(void)
|
|
{
|
|
at91_register_uart(0, 0);
|
|
return 0;
|
|
}
|
|
|
|
console_initcall(at91sam9260ek_console_init);
|