Commit 17176c2e2b
adds a test of a new RTC
register flag to distinguish a system reset and a wake up event. Shame on me,
I have forgotten to define the newly used flag yet.
While already here, I also try to document the other flags the RTC provides.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
227 lines
7.2 KiB
C
227 lines
7.2 KiB
C
/*
|
|
* (c) 2012 Juergen Beisert <kernel@pengutronix.de>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* Note: this driver works for the i.MX28 SoC. It might work for the
|
|
* i.MX23 Soc as well, but is not tested yet.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <io.h>
|
|
#include <errno.h>
|
|
#include <malloc.h>
|
|
#include <watchdog.h>
|
|
#include <reset_source.h>
|
|
|
|
#define MXS_RTC_CTRL 0x0
|
|
#define MXS_RTC_SET_ADDR 0x4
|
|
#define MXS_RTC_CLR_ADDR 0x8
|
|
# define MXS_RTC_CTRL_WATCHDOGEN (1 << 4)
|
|
|
|
#define MXS_RTC_STAT 0x10
|
|
# define MXS_RTC_STAT_WD_PRESENT (1 << 29)
|
|
|
|
#define MXS_RTC_WATCHDOG 0x50
|
|
|
|
/* HW_RTC_PERSISTENT0 - holds bits used to configure various hardware settings */
|
|
#define MXS_RTC_PERSISTENT0 0x60
|
|
|
|
/* FIXME */
|
|
# define MXS_RTC_PERSISTENT0_SPARE_ANALOG (1 << 22)
|
|
/* dubious meaning from inside the SoC's firmware ROM */
|
|
# define MXS_RTC_PERSISTENT0_EXT_RST (1 << 21)
|
|
/* dubious meaning from inside the SoC's firmware ROM */
|
|
# define MXS_RTC_PERSISTENT0_THM_RST (1 << 20)
|
|
/* reserved on i.MX28 */
|
|
# define MXS_RTC_PERSISTENT0_RELEASE_GND (1 << 19)
|
|
# define MXS_RTC_PERSISTENT0_ENABLE_LRADC_PWRUP (1 << 18)
|
|
# define MXS_RTC_PERSISTENT0_AUTO_RESTART (1 << 17)
|
|
# define MXS_RTC_PERSISTENT0_DISABLE_PSWITCH (1 << 16)
|
|
# define MXS_RTC_PERSISTENT0_LOWERBIAS (1 << 14)
|
|
# define MXS_RTC_PERSISTENT0_DISABLE_XTALOK (1 << 13)
|
|
# define MXS_RTC_PERSISTENT0_MSEC_RES (1 << 8)
|
|
# define MXS_RTC_PERSISTENT0_ALARM_WAKE (1 << 7)
|
|
# define MXS_RTC_PERSISTENT0_XTAL32_FREQ (1 << 6)
|
|
# define MXS_RTC_PERSISTENT0_XTAL32KHZ_PWRUP (1 << 5)
|
|
# define MXS_RTC_PERSISTENT0_XTAL24MHZ_PWRUP (1 << 4)
|
|
# define MXS_RTC_PERSISTENT0_LCK_SECS (1 << 3)
|
|
# define MXS_RTC_PERSISTENT0_ALARM_EN (1 << 2)
|
|
# define MXS_RTC_PERSISTENT0_ALARM_WAKE_EN (1 << 1)
|
|
# define MXS_RTC_PERSISTENT0_CLOCKSOURCE (1 << 0)
|
|
|
|
/* HW_RTC_PERSISTENT1 - holds bits related to the ROM and redundant boot handling */
|
|
#define MXS_RTC_PERSISTENT1 0x70
|
|
|
|
|
|
/*
|
|
* some of the following bits are for error reporting from ROM to the chained
|
|
* firmware. It seems, if the error reporting bits are not cleared when the
|
|
* chained firmware is running, the next time the following rule is active:
|
|
* "Loader enters recovery mode if any non-USB boot mode has an error.
|
|
* Which results into a system that seems not to start anymore.
|
|
*/
|
|
|
|
/* dubious meaning from inside the SoC's firmware ROM */
|
|
# define MXS_RTC_PERSISTENT1_FORCE_UPDATER (1 << 31)
|
|
|
|
/* names are from the i.MX28 datasheet. Undocumented behaviour */
|
|
# define MXS_RTC_PERSISTENT1_ENUMERATE_500MA_TWICE (1 << 12)
|
|
# define MXS_RTC_PERSISTENT1_USB_BOOT_PLAYER_MODE (1 << 11)
|
|
# define MXS_RTC_PERSISTENT1_SKIP_CHECKDISK (1 << 10)
|
|
# define MXS_RTC_PERSISTENT1_USB_LOW_POWER_MODE (1 << 9)
|
|
# define MXS_RTC_PERSISTENT1_OTG_HNP_BIT (1 << 8)
|
|
# define MXS_RTC_PERSISTENT1_OTG_ATL_ROLE_BIT (1 << 7)
|
|
/*
|
|
* a few undocumented bits
|
|
*/
|
|
# define MXS_RTC_PERSISTENT1_SD_INIT_SEQ_2_ENABLE (1 << 6)
|
|
# define MXS_RTC_PERSISTENT1_SD_CMD0_DISABLE (1 << 5)
|
|
# define MXS_RTC_PERSISTENT1_SD_INIT_SEQ_1_DISABLE (1 << 4)
|
|
/*
|
|
* If this bit is set, ROM puts the SD/MMC card in high-speed mode.
|
|
* If this bit is set, the ROM driver will use a maximum speed based on the
|
|
* results of device identification and limited by choices available in the
|
|
* SSP clock index.
|
|
*/
|
|
# define MXS_RTC_PERSISTENT1_SD_SPEED_ENABLE (1 << 3)
|
|
/*
|
|
* The NAND driver sets this bit to indicate to the SDK that the boot image
|
|
* has ECC errors that reached the warning threshold. The SDK regenerates the
|
|
* firmware by copying it from the backup image. The SDK clears this bit.
|
|
* This bit had change its meaning from i.XM23 to i.MX28. Refer section
|
|
* 35.8 "NAND Boot Mode" for further details in the i.MX23 RM.
|
|
*/
|
|
# define MXS_RTC_PERSISTENT1_NAND_SDK_BLOCK_REWRITE (1 << 2)
|
|
/*
|
|
* When this bit is set, ROM attempts to boot from the secondary image if the
|
|
* boot driver supports it. This bit is set by the ROM boot driver and cleared
|
|
* by the SDK after repair.
|
|
* If not reset, the ROM seems to continue to start from the secondary image
|
|
* which will fail forever if there is no secondary image
|
|
*/
|
|
# define MXS_RTC_PERSISTENT1_NAND_SECONDARY_BOOT (1 << 1)
|
|
/*
|
|
* When this bit is set, the ROM code forces the system to boot in recovery
|
|
* mode, regardless of the selected mode. The ROM clears the bit.
|
|
*/
|
|
# define MXS_RTC_PERSISTENT1_FORCE_RECOVERY (1 << 0)
|
|
|
|
#define MXS_RTC_DEBUG 0xc0
|
|
|
|
#define WDOG_TICK_RATE 1000 /* the watchdog uses a 1 kHz clock rate */
|
|
|
|
struct imx28_wd {
|
|
struct watchdog wd;
|
|
void __iomem *regs;
|
|
};
|
|
|
|
#define to_imx28_wd(h) container_of(h, struct imx28_wd, wd)
|
|
|
|
static int imx28_watchdog_set_timeout(struct watchdog *wd, unsigned timeout)
|
|
{
|
|
struct imx28_wd *pwd = (struct imx28_wd *)to_imx28_wd(wd);
|
|
void __iomem *base;
|
|
|
|
if (timeout > (ULONG_MAX / WDOG_TICK_RATE))
|
|
return -EINVAL;
|
|
|
|
if (timeout) {
|
|
writel(timeout * WDOG_TICK_RATE, pwd->regs + MXS_RTC_WATCHDOG);
|
|
base = pwd->regs + MXS_RTC_SET_ADDR;
|
|
} else {
|
|
base = pwd->regs + MXS_RTC_CLR_ADDR;
|
|
}
|
|
writel(MXS_RTC_CTRL_WATCHDOGEN, base + MXS_RTC_CTRL);
|
|
writel(MXS_RTC_PERSISTENT1_FORCE_UPDATER, base + MXS_RTC_PERSISTENT1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void __maybe_unused imx28_detect_reset_source(const struct imx28_wd *p)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = readl(p->regs + MXS_RTC_PERSISTENT0);
|
|
if (reg & MXS_RTC_PERSISTENT0_EXT_RST) {
|
|
writel(MXS_RTC_PERSISTENT0_EXT_RST,
|
|
p->regs + MXS_RTC_PERSISTENT0 + MXS_RTC_CLR_ADDR);
|
|
/*
|
|
* if the RTC has woken up the SoC, additionally the ALARM_WAKE
|
|
* bit is set. This bit should have precedence, because it
|
|
* reports the real event, why we are here.
|
|
*/
|
|
if (reg & MXS_RTC_PERSISTENT0_ALARM_WAKE) {
|
|
writel(MXS_RTC_PERSISTENT0_ALARM_WAKE,
|
|
p->regs + MXS_RTC_PERSISTENT0 + MXS_RTC_CLR_ADDR);
|
|
set_reset_source(RESET_WKE);
|
|
return;
|
|
}
|
|
set_reset_source(RESET_POR);
|
|
return;
|
|
}
|
|
if (reg & MXS_RTC_PERSISTENT0_THM_RST) {
|
|
writel(MXS_RTC_PERSISTENT0_THM_RST,
|
|
p->regs + MXS_RTC_PERSISTENT0 + MXS_RTC_CLR_ADDR);
|
|
set_reset_source(RESET_RST);
|
|
return;
|
|
}
|
|
|
|
set_reset_source(RESET_RST);
|
|
}
|
|
|
|
static int imx28_wd_probe(struct device_d *dev)
|
|
{
|
|
struct imx28_wd *priv;
|
|
int rc;
|
|
|
|
priv = xzalloc(sizeof(struct imx28_wd));
|
|
priv->regs = dev_request_mem_region(dev, 0);
|
|
priv->wd.set_timeout = imx28_watchdog_set_timeout;
|
|
|
|
if (!(readl(priv->regs + MXS_RTC_STAT) & MXS_RTC_STAT_WD_PRESENT)) {
|
|
rc = -ENODEV;
|
|
goto on_error;
|
|
}
|
|
|
|
/* disable the debug feature to ensure a working WD */
|
|
writel(0x00000000, priv->regs + MXS_RTC_DEBUG);
|
|
|
|
rc = watchdog_register(&priv->wd);
|
|
if (rc != 0)
|
|
goto on_error;
|
|
|
|
if (IS_ENABLED(CONFIG_RESET_SOURCE))
|
|
imx28_detect_reset_source(priv);
|
|
|
|
dev->priv = priv;
|
|
return 0;
|
|
|
|
on_error:
|
|
free(priv);
|
|
return rc;
|
|
}
|
|
|
|
static void imx28_wd_remove(struct device_d *dev)
|
|
{
|
|
struct imx28_wd *priv= dev->priv;
|
|
watchdog_deregister(&priv->wd);
|
|
free(priv);
|
|
}
|
|
|
|
static struct driver_d imx28_wd_driver = {
|
|
.name = "im28wd",
|
|
.probe = imx28_wd_probe,
|
|
.remove = imx28_wd_remove,
|
|
};
|
|
device_platform_driver(imx28_wd_driver);
|