Adapt phylib from linux switch all the driver to it reimplement mii bus This will allow to have - phy drivers - to only connect the phy at then opening of the device - if the phy is not ready or not up fail on open Same behaviour as in linux and will allow to share code and simplify porting. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
115 lines
3.7 KiB
C
115 lines
3.7 KiB
C
/*
|
|
* ethtool.h: Defines for Linux ethtool.
|
|
*
|
|
* Copyright (C) 1998 David S. Miller (davem@redhat.com)
|
|
* Copyright 2001 Jeff Garzik <jgarzik@pobox.com>
|
|
* Portions Copyright 2001 Sun Microsystems (thockin@sun.com)
|
|
* Portions Copyright 2002 Intel (eli.kupermann@intel.com,
|
|
* christopher.leech@intel.com,
|
|
* scott.feldman@intel.com)
|
|
* Portions Copyright (C) Sun Microsystems 2008
|
|
*/
|
|
|
|
#ifndef _LINUX_ETHTOOL_H
|
|
#define _LINUX_ETHTOOL_H
|
|
|
|
/* Indicates what features are supported by the interface. */
|
|
#define SUPPORTED_10baseT_Half (1 << 0)
|
|
#define SUPPORTED_10baseT_Full (1 << 1)
|
|
#define SUPPORTED_100baseT_Half (1 << 2)
|
|
#define SUPPORTED_100baseT_Full (1 << 3)
|
|
#define SUPPORTED_1000baseT_Half (1 << 4)
|
|
#define SUPPORTED_1000baseT_Full (1 << 5)
|
|
#define SUPPORTED_Autoneg (1 << 6)
|
|
#define SUPPORTED_TP (1 << 7)
|
|
#define SUPPORTED_AUI (1 << 8)
|
|
#define SUPPORTED_MII (1 << 9)
|
|
#define SUPPORTED_FIBRE (1 << 10)
|
|
#define SUPPORTED_BNC (1 << 11)
|
|
#define SUPPORTED_10000baseT_Full (1 << 12)
|
|
#define SUPPORTED_Pause (1 << 13)
|
|
#define SUPPORTED_Asym_Pause (1 << 14)
|
|
#define SUPPORTED_2500baseX_Full (1 << 15)
|
|
#define SUPPORTED_Backplane (1 << 16)
|
|
#define SUPPORTED_1000baseKX_Full (1 << 17)
|
|
#define SUPPORTED_10000baseKX4_Full (1 << 18)
|
|
#define SUPPORTED_10000baseKR_Full (1 << 19)
|
|
#define SUPPORTED_10000baseR_FEC (1 << 20)
|
|
|
|
/* Indicates what features are advertised by the interface. */
|
|
#define ADVERTISED_10baseT_Half (1 << 0)
|
|
#define ADVERTISED_10baseT_Full (1 << 1)
|
|
#define ADVERTISED_100baseT_Half (1 << 2)
|
|
#define ADVERTISED_100baseT_Full (1 << 3)
|
|
#define ADVERTISED_1000baseT_Half (1 << 4)
|
|
#define ADVERTISED_1000baseT_Full (1 << 5)
|
|
#define ADVERTISED_Autoneg (1 << 6)
|
|
#define ADVERTISED_TP (1 << 7)
|
|
#define ADVERTISED_AUI (1 << 8)
|
|
#define ADVERTISED_MII (1 << 9)
|
|
#define ADVERTISED_FIBRE (1 << 10)
|
|
#define ADVERTISED_BNC (1 << 11)
|
|
#define ADVERTISED_10000baseT_Full (1 << 12)
|
|
#define ADVERTISED_Pause (1 << 13)
|
|
#define ADVERTISED_Asym_Pause (1 << 14)
|
|
#define ADVERTISED_2500baseX_Full (1 << 15)
|
|
#define ADVERTISED_Backplane (1 << 16)
|
|
#define ADVERTISED_1000baseKX_Full (1 << 17)
|
|
#define ADVERTISED_10000baseKX4_Full (1 << 18)
|
|
#define ADVERTISED_10000baseKR_Full (1 << 19)
|
|
#define ADVERTISED_10000baseR_FEC (1 << 20)
|
|
|
|
/* The following are all involved in forcing a particular link
|
|
* mode for the device for setting things. When getting the
|
|
* devices settings, these indicate the current mode and whether
|
|
* it was foced up into this mode or autonegotiated.
|
|
*/
|
|
|
|
/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */
|
|
#define SPEED_10 10
|
|
#define SPEED_100 100
|
|
#define SPEED_1000 1000
|
|
#define SPEED_2500 2500
|
|
#define SPEED_10000 10000
|
|
|
|
/* Duplex, half or full. */
|
|
#define DUPLEX_HALF 0x00
|
|
#define DUPLEX_FULL 0x01
|
|
|
|
/* Which connector port. */
|
|
#define PORT_TP 0x00
|
|
#define PORT_AUI 0x01
|
|
#define PORT_MII 0x02
|
|
#define PORT_FIBRE 0x03
|
|
#define PORT_BNC 0x04
|
|
#define PORT_OTHER 0xff
|
|
|
|
/* Which transceiver to use. */
|
|
#define XCVR_INTERNAL 0x00
|
|
#define XCVR_EXTERNAL 0x01
|
|
#define XCVR_DUMMY1 0x02
|
|
#define XCVR_DUMMY2 0x03
|
|
#define XCVR_DUMMY3 0x04
|
|
|
|
/* Enable or disable autonegotiation. If this is set to enable,
|
|
* the forced link modes above are completely ignored.
|
|
*/
|
|
#define AUTONEG_DISABLE 0x00
|
|
#define AUTONEG_ENABLE 0x01
|
|
|
|
/* Mode MDI or MDI-X */
|
|
#define ETH_TP_MDI_INVALID 0x00
|
|
#define ETH_TP_MDI 0x01
|
|
#define ETH_TP_MDI_X 0x02
|
|
|
|
/* Wake-On-Lan options. */
|
|
#define WAKE_PHY (1 << 0)
|
|
#define WAKE_UCAST (1 << 1)
|
|
#define WAKE_MCAST (1 << 2)
|
|
#define WAKE_BCAST (1 << 3)
|
|
#define WAKE_ARP (1 << 4)
|
|
#define WAKE_MAGIC (1 << 5)
|
|
#define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */
|
|
|
|
#endif /* _LINUX_ETHTOOL_H */
|