Drop beagleboard, replaced by beaglebone

(From meta-yocto rev: b125761e5e31fc506f7b5b87308850cd573ab1b6)

Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
This commit is contained in:
Richard Purdie 2014-03-28 18:07:01 +00:00
parent af1e58a610
commit 7254dfb642
8 changed files with 0 additions and 202 deletions

View File

@ -46,7 +46,6 @@ Hardware Reference Boards
The following boards are supported by the meta-yocto-bsp layer:
* Texas Instruments Beagleboard (beagleboard)
* Freescale MPC8315E-RDB (mpc8315e-rdb)
* Ubiquiti Networks RouterStation Pro (routerstationpro)
@ -180,96 +179,6 @@ USB Device:
http://git.kernel.org/?p=boot/syslinux/syslinux.git;a=blob_plain;f=doc/usbkey.txt;hb=HEAD
Texas Instruments Beagleboard (beagleboard)
===========================================
The Beagleboard is an ARM Cortex-A8 development board with USB, DVI-D, S-Video,
2D/3D accelerated graphics, audio, serial, JTAG, and SD/MMC. The xM adds a
faster CPU, more RAM, an ethernet port, more USB ports, microSD, and removes
the NAND flash. The beagleboard MACHINE is tested on the following platforms:
o Beagleboard C4
o Beagleboard xM rev A & B
The Beagleboard C4 has NAND, while the xM does not. For the sake of simplicity,
these instructions assume you have erased the NAND on the C4 so its boot
behavior matches that of the xM. To do this, issue the following commands from
the u-boot prompt (note that the unlock may be unecessary depending on the
version of u-boot installed on your board and only one of the erase commands
will succeed):
# nand unlock
# nand erase
# nand erase.chip
To further tailor these instructions for your board, please refer to the
documentation at http://www.beagleboard.org.
From a Linux system with access to the image files perform the following steps
as root, replacing mmcblk0* with the SD card device on your machine (such as sdc
if used via a usb card reader):
1. Partition and format an SD card:
# fdisk -lu /dev/mmcblk0
Disk /dev/mmcblk0: 3951 MB, 3951034368 bytes
255 heads, 63 sectors/track, 480 cylinders, total 7716864 sectors
Units = sectors of 1 * 512 = 512 bytes
Device Boot Start End Blocks Id System
/dev/mmcblk0p1 * 63 144584 72261 c Win95 FAT32 (LBA)
/dev/mmcblk0p2 144585 465884 160650 83 Linux
# mkfs.vfat -F 16 -n "boot" /dev/mmcblk0p1
# mke2fs -j -L "root" /dev/mmcblk0p2
The following assumes the SD card partition 1 and 2 are mounted at
/media/boot and /media/root respectively. Removing the card and reinserting
it will do just that on most modern Linux desktop environments.
The files referenced below are made available after the build in
build/tmp/deploy/images.
2. Install the boot loaders
# cp MLO-beagleboard /media/boot/MLO
# cp u-boot-beagleboard.bin /media/boot/u-boot.bin
3. Install the root filesystem
# tar x -C /media/root -f core-image-$IMAGE_TYPE-beagleboard.tar.bz2
# tar x -C /media/root -f modules-$KERNEL_VERSION-beagleboard.tgz
4. Install the kernel uImage
# cp uImage-beagleboard.bin /media/boot/uImage
5. Prepare a u-boot script to simplify the boot process
The Beagleboard can be made to boot at this point from the u-boot command
shell. To automate this process, generate a user.scr script as follows.
Install uboot-mkimage (from uboot-mkimage on Ubuntu or uboot-tools on Fedora).
Prepare a script config:
# (cat << EOF
setenv bootcmd 'mmc init; fatload mmc 0:1 0x80300000 uImage; bootm 0x80300000'
setenv bootargs 'console=tty0 console=ttyO2,115200n8 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro'
boot
EOF
) > serial-boot.cmd
# mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Core Minimal" -d ./serial-boot.cmd ./boot.scr
# cp boot.scr /media/boot
6. Unmount the SD partitions, insert the SD card into the Beagleboard, and
boot the Beagleboard
Note: As of the 2.6.37 linux-yocto kernel recipe, the Beagleboard uses the
OMAP_SERIAL device (ttyO2). If you are using an older kernel, such as the
2.6.34 linux-yocto-stable, be sure to replace ttyO2 with ttyS2 above. You
should also override the machine SERIAL_CONSOLE in your local.conf in
order to setup the getty on the serial line:
SERIAL_CONSOLE_beagleboard = "115200 ttyS2"
Freescale MPC8315E-RDB (mpc8315e-rdb)
=====================================

View File

@ -1,43 +0,0 @@
#@TYPE: Machine
#@NAME: Beagleboard machine
#@DESCRIPTION: Machine configuration for the http://beagleboard.org/ board
PREFERRED_PROVIDER_virtual/xserver ?= "xserver-xorg"
XSERVER ?= "xserver-xorg \
xf86-input-evdev \
xf86-input-mouse \
xf86-video-omapfb \
xf86-input-keyboard"
# Ship all kernel modules by default
MACHINE_EXTRA_RRECOMMENDS = " kernel-modules"
# Allow for MMC booting (required by the NAND-less Beagleboard XM)
EXTRA_IMAGEDEPENDS += "u-boot"
# Uncomment the following line to enable the hard floating point abi. Note that
# this breaks some binary libraries and 3D (neither of which ship with
# meta-yocto). For maximum compatibility, leave this disabled.
#DEFAULTTUNE ?= "cortexa8hf-neon"
include conf/machine/include/tune-cortexa8.inc
IMAGE_FSTYPES += "tar.bz2 jffs2"
EXTRA_IMAGECMD_jffs2 = "-lnp "
# 2.6.37 and later kernels use OMAP_SERIAL, ttyO2
# earlier kernels use ttyS2
SERIAL_CONSOLE = "115200 ttyO2"
PREFERRED_PROVIDER_virtual/kernel ?= "linux-yocto"
PREFERRED_VERSION_linux-yocto ?= "3.10%"
KERNEL_IMAGETYPE = "zImage"
KERNEL_DEVICETREE = "${S}/arch/arm/boot/dts/omap3-beagle.dts ${S}/arch/arm/boot/dts/omap3-beagle-xm.dts"
SPL_BINARY = "MLO"
UBOOT_SUFFIX = "img"
UBOOT_MACHINE = "omap3_beagle_config"
UBOOT_ENTRYPOINT = "0x80008000"
UBOOT_LOADADDRESS = "0x80008000"
MACHINE_FEATURES = "usbgadget usbhost vfat alsa"

View File

@ -1,27 +0,0 @@
# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
# The loopback interface
auto lo
iface lo inet loopback
# Wireless interfaces
iface wlan0 inet dhcp
wireless_mode managed
wireless_essid any
wpa-driver wext
wpa-conf /etc/wpa_supplicant.conf
iface atml0 inet dhcp
# Wired or wireless interfaces
auto eth0
iface eth0 inet dhcp
iface eth1 inet dhcp
# Ethernet/RNDIS gadget (g_ether) or LAN9514 on BeagleBoard xM
auto usb0
iface usb0 inet dhcp
# Bluetooth networking
iface bnep0 inet dhcp

View File

@ -1 +0,0 @@
FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}-${PV}:"

View File

@ -1,33 +0,0 @@
Section "Module"
Load "extmod"
Load "dbe"
Load "glx"
Load "freetype"
Load "type1"
Load "record"
Load "dri"
EndSection
Section "Monitor"
Identifier "Builtin Default Monitor"
EndSection
Section "Device"
Identifier "Builtin Default fbdev Device 0"
Driver "omapfb"
EndSection
Section "Screen"
Identifier "Builtin Default fbdev Screen 0"
Device "Builtin Default fbdev Device 0"
Monitor "Builtin Default Monitor"
EndSection
Section "ServerLayout"
Identifier "Builtin Default Layout"
Screen "Builtin Default fbdev Screen 0"
EndSection
Section "ServerFlags"
Option "DontZap" "0"
EndSection

View File

@ -2,7 +2,6 @@ KBRANCH_genericx86 = "standard/common-pc/base"
KBRANCH_genericx86-64 = "standard/common-pc-64/base"
KBRANCH_routerstationpro = "standard/routerstationpro"
KBRANCH_mpc8315e-rdb = "standard/fsl-mpc8315e-rdb"
KBRANCH_beagleboard = "standard/beagleboard"
KMACHINE_genericx86 ?= "common-pc"
KMACHINE_genericx86-64 ?= "common-pc-64"
@ -11,13 +10,11 @@ SRCREV_machine_genericx86 ?= "2ee37bfe732c73f7d39af55875ce8d30b282471c"
SRCREV_machine_genericx86-64 ?= "2ee37bfe732c73f7d39af55875ce8d30b282471c"
SRCREV_machine_routerstationpro ?= "628fb65e665a4179b6df049563f47f521f9dfb4e"
SRCREV_machine_mpc8315e-rdb ?= "2688f74bf2bb01ec355bbdd4b6fa00a0d39302de"
SRCREV_machine_beagleboard ?= "dbd7d0033e92dcec6682760982228e88df9982e2"
COMPATIBLE_MACHINE_genericx86 = "genericx86"
COMPATIBLE_MACHINE_genericx86-64 = "genericx86-64"
COMPATIBLE_MACHINE_mpc8315e-rdb = "mpc8315e-rdb"
COMPATIBLE_MACHINE_routerstationpro = "routerstationpro"
COMPATIBLE_MACHINE_beagleboard = "beagleboard"
# routerstationpro has a flash size of 16mb
KERNEL_IMAGE_MAXSIZE_routerstationpro = "16777216"

View File

@ -1,15 +1,12 @@
KBRANCH_routerstationpro = "standard/routerstationpro"
KBRANCH_mpc8315e-rdb = "standard/fsl-mpc8315e-rdb"
KBRANCH_beagleboard = "standard/beagleboard"
SRCREV_machine_genericx86 ?= "cdd7a546922ca1c46c94adeec3b9c90dc9aaad2d"
SRCREV_machine_routerstationpro ?= "62b86dc8ac794cd97c61a99418d7429e6a83ec1a"
SRCREV_machine_mpc8315e-rdb ?= "b2f78892b3ff6cc940e4661f7b2017a73b289c73"
SRCREV_machine_beagleboard ?= "cdd7a546922ca1c46c94adeec3b9c90dc9aaad2d"
COMPATIBLE_MACHINE_mpc8315e-rdb = "mpc8315e-rdb"
COMPATIBLE_MACHINE_routerstationpro = "routerstationpro"
COMPATIBLE_MACHINE_beagleboard = "beagleboard"
# routerstationpro has a flash size of 16mb
KERNEL_IMAGE_MAXSIZE_append_routerstationpro = "16777216"

View File

@ -319,7 +319,6 @@ DESCRIPTION
["yocto/pvr", "yocto/pvr"]
["yocto/standard/arm-versatile-926ejs", "yocto/standard/arm-versatile-926ejs"]
["yocto/standard/base", "yocto/standard/base"]
["yocto/standard/beagleboard", "yocto/standard/beagleboard"]
["yocto/standard/cedartrail", "yocto/standard/cedartrail"]
.
.