The sources are not using autotools and the
build breaks.
ERROR: Function failed: do_install (log file is located at /home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/armv5te-poky-linux-gnueabi/i2c-tools/3.1.1-r0/temp/log.do_install.10782)
ERROR: Logfile of failure stored in: /home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/armv5te-poky-linux-gnueabi/i2c-tools/3.1.1-r0/temp/log.do_install.10782
Log data follows:
| DEBUG: SITE files ['endian-little', 'bit-32', 'arm-common', 'arm-32', 'common-linux', 'common-glibc', 'arm-linux', 'arm-linux-gnueabi', 'common']
| DEBUG: Executing shell function do_install
| NOTE: make -j 2 DESTDIR=/home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/armv5te-poky-linux-gnueabi/i2c-tools/3.1.1-r0/image install
| make: *** No rule to make target `install'. Stop.
| ERROR: oe_runmake failed
| WARNING: /home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/armv5te-poky-linux-gnueabi/i2c-tools/3.1.1-r0/temp/run.do_install.10782:1 exit 1 from
| exit 1
| ERROR: Function failed: do_install (log file is located at /home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/armv5te-poky-linux-gnueabi/i2c-tools/3.1.1-r0/temp/log.do_install.10782)
NOTE: recipe i2c-tools-3.1.1-r0: task do_install: Failed
In yocto versions before dizzy/master the build was done
in the source directory and when configure was executed
twice in the same directory we would have a build failure
due the symlink already existing. Simply assume that if
the ln fails the link is already there.
Out of disk space situations are handled more early by
OE and missing files will be found by configure.
In dizzy/master OE will clean the build directory before
calling configure so the issue does not apply there.
Fixes: SYS#1170
This is a late fall-out of the priority changes done by
Henning. This recipe is not using autotools and doesn't
support src != build dir builds. So let's not use the
autotools class but simply invoke install ourselves. Let's
lower the default preference so the recipe from yocto master
is picked as well.
ERROR: Function failed: do_install (log file is located at /home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/all-poky-linux/ca-certificates/20120623-r0/temp/log.do_install.16890)
ERROR: Logfile of failure stored in: /home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/all-poky-linux/ca-certificates/20120623-r0/temp/log.do_install.16890
Log data follows:
| DEBUG: SITE files ['endian-little', 'bit-32', 'common-linux', 'common-glibc', 'allarch-linux', 'common']
| DEBUG: Executing shell function do_install
| NOTE: make -j 2 DESTDIR=/home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/all-poky-linux/ca-certificates/20120623-r0/image install
| make: *** No rule to make target `install'. Stop.
| ERROR: oe_runmake failed
| WARNING: /home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/all-poky-linux/ca-certificates/20120623-r0/temp/run.do_install.16890:1 exit 1 from
| exit 1
| ERROR: Function failed: do_install (log file is located at /home/builder/jenkins/workspace/Yocto-Master/label/OE/build/tmp/work/all-poky-linux/ca-certificates/20120623-r0/temp/log.do_install.16890)
NOTE: recipe ca-certificates-20120623-r0: task do_install: Failed
ERROR: Task 3639 (/home/builder/jenkins/workspace/Yocto-Master/label/OE/meta-sysmocom-bsp/recipes-extra/ca-certificates/ca-certificates_20120623.bb, do_install) failed with exit code '1'
A lease bound/renewal could lead to the removal of a default
route set by pppd. Apply the same "dev $interface" filter that
would be used when using the "route" command.
Fixes: SYS#1163
The IDU is powerful enough to run the journald. This gives us
some convenienance to have additional output from our services
and we can query them at a later point in time.
This will only be useful for systems that are re-installed
from scratch.
Fixes: SYS#892
UUCP (cu, uux, uu*) attempts to create locks in /run/lock and it
fails. It fails because the current permission of the directory is
0755 but the binary is owned by uucp:root. Modify the legacy.conf
and change the permission to 0775.
I edited the config through make menuconfig and then used
savedefconfig but the diff from our config to a minimal
defconfig is too big. So I enabled the temp sensors and i2c
by hand.
Fixes: SYS#1148
The current 1:0.1+git1+019d2535b6-r9.2 is considered to be older
than the new gpsdate_0.1+git0+2326eee789-r10 file. Change the
PE to benefit from an upgrade.
The ODU has the GPSD for GNSS/GPS listening on a different
port. In hindsight this was a stupid decision but one we can
only fix once we move to generating the config of the system
at boot time.
Fixes: SYS#906
In case the port is not in a forwarding state.. don't just
give up but background and move on. This appears to be needed
for the odu to acquire a lease when STP is used.
For the V-ODU we want to have vlan support as well. This requires
to use the debian ifupdown which means we need a script that creates
/run/network early enough.
The name of the config file was changed and so far
I was hesitant to upgrade the MLO. I think the change
in EEPROM applies to the MLO as well so we should
upgrade it. It has neither been build tested nor tested
on a device.
On eth1 we should also use a network from the 172.16 block rather than
the 10.23 that we used on the sysmoBSC
Also, we now use 172.16.4.0/23 natively on the bridged onboard network,
this is a temporary measure so existing JBs will still connect and get
an IP address before their software is updated to use VLAN6. After they
(and all APs, BTSs, etc.) have migrated, the 172.16.4.0/23 can be
removed.
For systemd and the Debian ifupdown application we need to
have the /run/network directory. The debian init file is
creating it on the fly and we should do the same for now.
networking.service - LSB: Raise network interfaces.
Loaded: loaded (/etc/init.d/networking)
Active: failed (Result: exit-code) since Fri 2015-02-13 17:59:17 UTC; 43s ago
Process: 54 ExecStart=/etc/init.d/networking start (code=exited, status=1/FAILURE)
Feb 13 18:04:47 sysmocom-idu networking[54]: ifup: failed to open lockfile /run
/network/.ifstate.lock: No such file or directory
The creation of /run/network occurs way too late. So we need
to look for another solution.
This reverts commit 86dda7481f.
* DHCP range for 'vlan6' onboard network 172.16.2.0/23
* DHCP range for 'native' onboard network 172.16.4.0/23
* DHCP range for 'admin' port eth1 172.16.6.0/24
* domain name vessel.sob.sysmocom.de
* listen on all interfaces, not just one
* allow admin to specify static leases (ODU) in /etc/dnsmasq.dhcp-hosts
$ ifup br0.6
would go throup _none_up of links.defn and never call the
set_environ for any of the files. Check for environ being
null and then call the set_environ function to initialize
the PATH. This is changing the semantic to allow the iface,
mode and phase to be NULL. I tried to add proper null checks
Harald Welte
Holger Hans Peter Freyther
Henning Heinold