u-boot/drivers/pcmcia/tqm8xx_pcmcia.c

255 lines
5.9 KiB
C
Raw Normal View History

/* -------------------------------------------------------------------- */
/* TQM8xxL Boards by TQ Components */
/* SC8xx Boards by SinoVee Microsystems */
/* -------------------------------------------------------------------- */
#include <common.h>
#include <asm/io.h>
2006-07-21 13:24:56 +00:00
#ifdef CONFIG_8xx
#include <mpc8xx.h>
2006-07-21 13:24:56 +00:00
#endif
#include <pcmcia.h>
#undef CONFIG_PCMCIA
#if defined(CONFIG_CMD_PCMCIA)
#define CONFIG_PCMCIA
#endif
#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
#define CONFIG_PCMCIA
#endif
#if defined(CONFIG_PCMCIA) \
&& defined(CONFIG_TQM8xxL)
#if defined(CONFIG_TQM8xxL)
#define PCMCIA_BOARD_MSG "TQM8xxL"
#endif
static inline void power_config(int slot)
{
immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
/*
* Configure Port C pins for
* 5 Volts Enable and 3 Volts enable
*/
clrbits_be16(&immap->im_ioport.iop_pcpar, 0x0002 | 0x0004);
clrbits_be16(&immap->im_ioport.iop_pcso, 0x0002 | 0x0004);
}
static inline void power_off(int slot)
{
immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
clrbits_be16(&immap->im_ioport.iop_pcdat, 0x0002 | 0x0004);
}
static inline void power_on_5_0(int slot)
{
immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
setbits_be16(&immap->im_ioport.iop_pcdat, 0x0004);
setbits_be16(&immap->im_ioport.iop_pcdir, 0x0002 | 0x0004);
}
static inline void power_on_3_3(int slot)
{
immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
setbits_be16(&immap->im_ioport.iop_pcdat, 0x0002);
setbits_be16(&immap->im_ioport.iop_pcdir, 0x0002 | 0x0004);
}
/*
* Function to retrieve the PIPR register, used for debuging purposes.
*/
static inline uint32_t debug_get_pipr(void)
{
uint32_t pipr = 0;
#ifdef DEBUG
immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
pipr = in_be32(&immap->im_pcmcia.pcmc_pipr);
#endif
return pipr;
}
static inline int check_card_is_absent(int slot)
{
immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
uint32_t pipr = in_be32(&immap->im_pcmcia.pcmc_pipr);
return pipr & (0x18000000 >> (slot << 4));
}
#define NSCU_GCRX_CXOE __MY_PCMCIA_GCRX_CXOE
int pcmcia_hardware_enable(int slot)
{
immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
uint reg, mask;
debug("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
udelay(10000);
/*
* Configure SIUMCR to enable PCMCIA port B
* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
*/
/* Set DBGC to 00 */
clrbits_be32(&immap->im_siu_conf.sc_siumcr, SIUMCR_DBGC11);
/* Clear interrupt state, and disable interrupts */
out_be32(&immap->im_pcmcia.pcmc_pscr, PCMCIA_MASK(slot));
clrbits_be32(&immap->im_pcmcia.pcmc_per, PCMCIA_MASK(slot));
/*
* Disable interrupts, DMA, and PCMCIA buffers
* (isolate the interface) and assert RESET signal
*/
debug("Disable PCMCIA buffers and assert RESET\n");
reg = 0;
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
reg |= NSCU_GCRX_CXOE;
PCMCIA_PGCRX(slot) = reg;
udelay(500);
power_config(slot);
power_off(slot);
/*
* Make sure there is a card in the slot, then configure the interface.
*/
udelay(10000);
reg = debug_get_pipr();
debug("[%d] %s: PIPR(%p)=0x%x\n", __LINE__, __FUNCTION__,
&immap->im_pcmcia.pcmc_pipr, reg);
if (check_card_is_absent(slot)) {
printf (" No Card found\n");
return (1);
}
/*
* Power On.
*/
mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
reg = in_be32(&immap->im_pcmcia.pcmc_pipr);
debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
reg,
(reg & PCMCIA_VS1(slot)) ? "n" : "ff",
(reg & PCMCIA_VS2(slot)) ? "n" : "ff");
if ((reg & mask) == mask) {
power_on_5_0(slot);
puts (" 5.0V card found: ");
} else {
power_on_3_3(slot);
puts (" 3.3V card found: ");
}
#if 0
/* VCC switch error flag, PCMCIA slot INPACK_ pin */
cp->cp_pbdir &= ~(0x0020 | 0x0010);
cp->cp_pbpar &= ~(0x0020 | 0x0010);
udelay(500000);
#endif
udelay(1000);
debug("Enable PCMCIA buffers and stop RESET\n");
reg = PCMCIA_PGCRX(slot);
reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
reg &= ~NSCU_GCRX_CXOE;
PCMCIA_PGCRX(slot) = reg;
udelay(250000); /* some cards need >150 ms to come up :-( */
debug("# hardware_enable done\n");
return (0);
}
#if defined(CONFIG_CMD_PCMCIA)
int pcmcia_hardware_disable(int slot)
{
u_long reg;
debug("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
/* remove all power */
power_off(slot);
debug("Disable PCMCIA buffers and assert RESET\n");
reg = 0;
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
reg |= NSCU_GCRX_CXOE; /* active low */
PCMCIA_PGCRX(slot) = reg;
udelay(10000);
return (0);
}
#endif
int pcmcia_voltage_set(int slot, int vcc, int vpp)
{
2006-07-21 13:24:56 +00:00
u_long reg;
uint32_t pipr = 0;
debug("voltage_set: " PCMCIA_BOARD_MSG
" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
/*
* Disable PCMCIA buffers (isolate the interface)
* and assert RESET signal
*/
debug("Disable PCMCIA buffers and assert RESET\n");
reg = PCMCIA_PGCRX(slot);
reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
reg |= NSCU_GCRX_CXOE; /* active low */
PCMCIA_PGCRX(slot) = reg;
udelay(500);
debug("PCMCIA power OFF\n");
power_config(slot);
power_off(slot);
switch(vcc) {
case 0: break;
case 33: power_on_3_3(slot); break;
case 50: power_on_5_0(slot); break;
default: goto done;
}
/* Checking supported voltages */
pipr = debug_get_pipr();
debug("PIPR: 0x%x --> %s\n", pipr,
(pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
if (vcc)
debug("PCMCIA powered at %sV\n", (vcc == 50) ? "5.0" : "3.3");
else
debug("PCMCIA powered down\n");
done:
debug("Enable PCMCIA buffers and stop RESET\n");
reg = PCMCIA_PGCRX(slot);
reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
reg &= ~NSCU_GCRX_CXOE; /* active low */
PCMCIA_PGCRX(slot) = reg;
udelay(500);
debug("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n", slot+'A');
return 0;
}
#endif /* CONFIG_PCMCIA && CONFIG_TQM8xxL */