u-boot/include/configs/ls1012aqds.h

190 lines
5 KiB
C
Raw Normal View History

/*
* Copyright 2016 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __LS1012AQDS_H__
#define __LS1012AQDS_H__
#include "ls1012a_common.h"
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
#define CONFIG_NR_DRAM_BANKS 2
#define CONFIG_SYS_SDRAM_SIZE 0x40000000
#define CONFIG_SYS_MMDC_CORE_CONTROL_1 0x05180000
#define CONFIG_SYS_MMDC_CORE_CONTROL_2 0x85180000
/*
* QIXIS Definitions
*/
#define CONFIG_FSL_QIXIS
#ifdef CONFIG_FSL_QIXIS
#define CONFIG_QIXIS_I2C_ACCESS
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
#define QIXIS_LBMAP_BRDCFG_REG 0x04
#define QIXIS_LBMAP_SWITCH 6
#define QIXIS_LBMAP_MASK 0xf7
#define QIXIS_LBMAP_SHIFT 0
#define QIXIS_LBMAP_DFLTBANK 0x00
#define QIXIS_LBMAP_ALTBANK 0x08
#define QIXIS_RST_CTL_RESET 0x41
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
#endif
/*
* I2C bus multiplexer
*/
#define I2C_MUX_PCA_ADDR_PRI 0x77
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
#define I2C_RETIMER_ADDR 0x18
#define I2C_MUX_CH_DEFAULT 0x8
#define I2C_MUX_CH_CH7301 0xC
#define I2C_MUX_CH5 0xD
#define I2C_MUX_CH7 0xF
#define I2C_MUX_CH_VOL_MONITOR 0xa
/*
* RTC configuration
*/
#define RTC
#define CONFIG_RTC_PCF8563 1
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
#define CONFIG_CMD_DATE
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* Voltage monitor on channel 2*/
#define I2C_VOL_MONITOR_ADDR 0x40
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
/* DSPI */
#define CONFIG_FSL_DSPI1
#define CONFIG_DEFAULT_SPI_BUS 1
#define CONFIG_CMD_SPI
#define MMAP_DSPI DSPI1_BASE_ADDR
#define CONFIG_SYS_DSPI_CTAR0 1
#define CONFIG_SYS_DSPI_CTAR1 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \
DSPI_CTAR_DT(0))
#define CONFIG_SPI_FLASH_SST /* cs1 */
#define CONFIG_SYS_DSPI_CTAR2 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
DSPI_CTAR_CSSCK(0) | DSPI_CTAR_ASC(0) | \
DSPI_CTAR_DT(0))
#define CONFIG_SPI_FLASH_STMICRO /* cs2 */
#define CONFIG_SYS_DSPI_CTAR3 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \
DSPI_CTAR_DT(0))
#define CONFIG_SPI_FLASH_EON /* cs3 */
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define CONFIG_SF_DEFAULT_BUS 1
#define CONFIG_SF_DEFAULT_CS 0
/*
* USB
*/
/* EHCI Support - disbaled by default */
/*#define CONFIG_HAS_FSL_DR_USB*/
#ifdef CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
/*XHCI Support - enabled by default*/
#define CONFIG_HAS_FSL_XHCI_USB
#ifdef CONFIG_HAS_FSL_XHCI_USB
#define CONFIG_USB_XHCI_FSL
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#define CONFIG_USB_STORAGE
#endif
/* MMC */
#define CONFIG_MMC
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#define CONFIG_GENERIC_MMC
#define CONFIG_DOS_PARTITION
#endif
/* SATA */
#define CONFIG_LIBATA
#define CONFIG_SCSI
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_CMD_SCSI
#define CONFIG_DOS_PARTITION
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_SYS_SATA AHCI_BASE_ADDR
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_PCI /* Enable PCI/PCIE */
#define CONFIG_PCIE1 /* PCIE controller 1 */
#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
#define FSL_PCIE_COMPAT "fsl,ls1043a-pcie"
#define CONFIG_SYS_PCI_64BIT
#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
#define CONFIG_SYS_PCIE_MEM_BUS 0x08000000
#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x04000000
#define CONFIG_SYS_PCIE_MEM_SIZE 0x80000000 /* 128M */
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_CMD_PCI
#define CONFIG_CMD_MEMINFO
#define CONFIG_CMD_MEMTEST
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
#define CONFIG_MISC_INIT_R
#endif /* __LS1012AQDS_H__ */