u-boot/board/xpedite1k/xpedite1k.c

360 lines
11 KiB
C
Raw Normal View History

/*
* Copyright (C) 2003 Travis B. Sawyer <travis.sawyer@sandburst.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/processor.h>
#include <spd_sdram.h>
#include <i2c.h>
#define BOOT_SMALL_FLASH 32 /* 00100000 */
#define FLASH_ONBD_N 2 /* 00000010 */
#define FLASH_SRAM_SEL 1 /* 00000001 */
long int fixed_sdram (void);
int board_early_init_f(void)
{
unsigned long sdrreg;
/* TBS: Setup the GPIO access for the user LEDs */
mfsdr(sdr_pfc0, sdrreg);
mtsdr(sdr_pfc0, (sdrreg & ~0x00000100) | 0x00000E00);
out32(CFG_GPIO_BASE + 0x018, (USR_LED0 | USR_LED1 | USR_LED2 | USR_LED3));
LED0_OFF();
LED1_OFF();
LED2_OFF();
LED3_OFF();
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
/* set the bus controller */
mtebc (pb0ap, 0x04055200); /* FLASH/SRAM */
mtebc (pb0cr, 0xfff18000); /* BAS=0xfff 1MB R/W 8-bit */
mtebc (pb1ap, 0x04055200); /* FLASH/SRAM */
mtebc (pb1cr, 0xfe098000); /* BAS=0xff8 16MB R/W 8-bit */
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
*-------------------------------------------------------------------*/
mtdcr (uic0sr, 0xffffffff); /* clear all */
mtdcr (uic0er, 0x00000000); /* disable all */
mtdcr (uic0cr, 0x00000003); /* SMI & UIC1 crit are critical */
mtdcr (uic0pr, 0xfffffe00); /* per ref-board manual */
mtdcr (uic0tr, 0x01c00000); /* per ref-board manual */
mtdcr (uic0vr, 0x00000001); /* int31 highest, base=0x000 */
mtdcr (uic0sr, 0xffffffff); /* clear all */
mtdcr (uic1sr, 0xffffffff); /* clear all */
mtdcr (uic1er, 0x00000000); /* disable all */
mtdcr (uic1cr, 0x00000000); /* all non-critical */
mtdcr (uic1pr, 0xffffc0ff); /* per ref-board manual */
mtdcr (uic1tr, 0x00ff8000); /* per ref-board manual */
mtdcr (uic1vr, 0x00000001); /* int31 highest, base=0x000 */
mtdcr (uic1sr, 0xffffffff); /* clear all */
mtdcr (uic2sr, 0xffffffff); /* clear all */
mtdcr (uic2er, 0x00000000); /* disable all */
mtdcr (uic2cr, 0x00000000); /* all non-critical */
mtdcr (uic2pr, 0xffffffff); /* per ref-board manual */
mtdcr (uic2tr, 0x00ff8c0f); /* per ref-board manual */
mtdcr (uic2vr, 0x00000001); /* int31 highest, base=0x000 */
mtdcr (uic2sr, 0xffffffff); /* clear all */
mtdcr (uicb0sr, 0xfc000000); /* clear all */
mtdcr (uicb0er, 0x00000000); /* disable all */
mtdcr (uicb0cr, 0x00000000); /* all non-critical */
mtdcr (uicb0pr, 0xfc000000); /* */
mtdcr (uicb0tr, 0x00000000); /* */
mtdcr (uicb0vr, 0x00000001); /* */
LED0_ON();
return 0;
}
int checkboard (void)
{
sys_info_t sysinfo;
get_sys_info (&sysinfo);
printf ("Board: XES XPedite1000 440GX\n");
printf ("\tVCO: %lu MHz\n", sysinfo.freqVCOMhz / 1000000);
printf ("\tCPU: %lu MHz\n", sysinfo.freqProcessor / 1000000);
printf ("\tPLB: %lu MHz\n", sysinfo.freqPLB / 1000000);
printf ("\tOPB: %lu MHz\n", sysinfo.freqOPB / 1000000);
printf ("\tEPB: %lu MHz\n", sysinfo.freqEPB / 1000000);
return (0);
}
long int initdram (int board_type)
{
long dram_size = 0;
#if defined(CONFIG_SPD_EEPROM)
dram_size = spd_sdram (0);
#else
dram_size = fixed_sdram ();
#endif
return dram_size;
}
#if defined(CFG_DRAM_TEST)
int testdram (void)
{
uint *pstart = (uint *) 0x00000000;
uint *pend = (uint *) 0x08000000;
uint *p;
for (p = pstart; p < pend; p++)
*p = 0xaaaaaaaa;
for (p = pstart; p < pend; p++) {
if (*p != 0xaaaaaaaa) {
printf ("SDRAM test fails at: %08x\n", (uint) p);
return 1;
}
}
for (p = pstart; p < pend; p++)
*p = 0x55555555;
for (p = pstart; p < pend; p++) {
if (*p != 0x55555555) {
printf ("SDRAM test fails at: %08x\n", (uint) p);
return 1;
}
}
return 0;
}
#endif
#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
*
* Assumes: 128 MB, non-ECC, non-registered
* PLB @ 133 MHz
*
************************************************************************/
long int fixed_sdram (void)
{
uint reg;
/*--------------------------------------------------------------------
* Setup some default
*------------------------------------------------------------------*/
mtsdram (mem_uabba, 0x00000000); /* ubba=0 (default) */
mtsdram (mem_slio, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
mtsdram (mem_devopt, 0x00000000); /* dll=0 ds=0 (normal) */
mtsdram (mem_wddctr, 0x00000000); /* wrcp=0 dcd=0 */
mtsdram (mem_clktr, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
/*--------------------------------------------------------------------
* Setup for board-specific specific mem
*------------------------------------------------------------------*/
/*
* Following for CAS Latency = 2.5 @ 133 MHz PLB
*/
mtsdram (mem_b0cr, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
mtsdram (mem_tr0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
/* RA=10 RD=3 */
mtsdram (mem_tr1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
mtsdram (mem_rtr, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
mtsdram (mem_cfg1, 0x00000000); /* Self-refresh exit, disable PM */
udelay (400); /* Delay 200 usecs (min) */
/*--------------------------------------------------------------------
* Enable the controller, then wait for DCEN to complete
*------------------------------------------------------------------*/
mtsdram (mem_cfg0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
for (;;) {
mfsdram (mem_mcsts, reg);
if (reg & 0x80000000)
break;
}
return (128 * 1024 * 1024); /* 128 MB */
}
#endif /* !defined(CONFIG_SPD_EEPROM) */
/*************************************************************************
* pci_pre_init
*
* This routine is called just prior to registering the hose and gives
* the board the opportunity to check things. Returning a value of zero
* indicates that things are bad & PCI initialization should be aborted.
*
* Different boards may wish to customize the pci controller structure
* (add regions, override default access routines, etc) or perform
* certain pre-initialization actions.
*
************************************************************************/
#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
int pci_pre_init(struct pci_controller * hose )
{
unsigned long strap;
/* See if we're supposed to setup the pci */
mfsdr(sdr_sdstp1, strap);
if ((strap & 0x00010000) == 0) {
return (0);
}
#if defined(CFG_PCI_FORCE_PCI_CONV)
/* Setup System Device Register PCIX0_XCR */
mfsdr(sdr_xcr, strap);
strap &= 0x0f000000;
mtsdr(sdr_xcr, strap);
#endif
return 1;
}
#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
/*************************************************************************
* pci_target_init
*
* The bootstrap configuration provides default settings for the pci
* inbound map (PIM). But the bootstrap config choices are limited and
* may not be sufficient for a given board.
*
************************************************************************/
#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller * hose )
{
DECLARE_GLOBAL_DATA_PTR;
/*--------------------------------------------------------------------------+
* Disable everything
*--------------------------------------------------------------------------*/
out32r( PCIX0_PIM0SA, 0 ); /* disable */
out32r( PCIX0_PIM1SA, 0 ); /* disable */
out32r( PCIX0_PIM2SA, 0 ); /* disable */
out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
/*--------------------------------------------------------------------------+
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
* options to not support sizes such as 128/256 MB.
*--------------------------------------------------------------------------*/
out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
out32r( PCIX0_PIM0LAH, 0 );
out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
out32r( PCIX0_BAR0, 0 );
/*--------------------------------------------------------------------------+
* Program the board's subsystem id/vendor id
*--------------------------------------------------------------------------*/
out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
}
#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
/*************************************************************************
* is_pci_host
*
* This routine is called to determine if a pci scan should be
* performed. With various hardware environments (especially cPCI and
* PPMC) it's insufficient to depend on the state of the arbiter enable
* bit in the strap register, or generic host/adapter assumptions.
*
* Rather than hard-code a bad assumption in the general 440 code, the
* 440 pci code requires the board to decide at runtime.
*
* Return 0 for adapter mode, non-zero for host (monarch) mode.
*
*
************************************************************************/
#if defined(CONFIG_PCI)
int is_pci_host(struct pci_controller *hose)
{
return ((in32(CFG_GPIO_BASE + 0x1C) & 0x00000800) == 0);
}
#endif /* defined(CONFIG_PCI) */
#ifdef CONFIG_POST
/*
* Returns 1 if keys pressed to start the power-on long-running tests
* Called from board_init_f().
*/
int post_hotkeys_pressed(void)
{
return (ctrlc());
}
void post_word_store (ulong a)
{
volatile ulong *save_addr =
(volatile ulong *)(CFG_POST_WORD_ADDR);
*save_addr = a;
}
ulong post_word_load (void)
{
volatile ulong *save_addr =
(volatile ulong *)(CFG_POST_WORD_ADDR);
return *save_addr;
}
#endif
/*-----------------------------------------------------------------------------
* board_get_enetaddr -- Read the MAC Addresses in the I2C EEPROM
*-----------------------------------------------------------------------------
*/
static int enetaddr_num = 0;
void board_get_enetaddr (uchar * enet)
{
int i;
unsigned char buff[0x100], *cp;
/* Initialize I2C */
i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
/* Read 256 bytes in EEPROM */
i2c_read (0x50, 0, 1, buff, 0x100);
if (enetaddr_num == 0) {
cp = &buff[0xF4];
enetaddr_num = 1;
}
else
cp = &buff[0xFA];
for (i = 0; i < 6; i++,cp++)
enet[i] = *cp;
printf ("MAC address = %02x:%02x:%02x:%02x:%02x:%02x\n",
enet[0], enet[1], enet[2], enet[3], enet[4], enet[5]);
}