u-boot/include/configs/MPC8360ERDK.h

630 lines
19 KiB
C
Raw Normal View History

/*
* Copyright (C) 2006 Freescale Semiconductor, Inc.
* Dave Liu <daveliu@freescale.com>
*
* Copyright (C) 2007 Logic Product Development, Inc.
* Peter Barada <peterb@logicpd.com>
*
* Copyright (C) 2007 MontaVista Software, Inc.
* Anton Vorontsov <avorontsov@ru.mvista.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 family */
#define CONFIG_QE 1 /* Has QE */
#define CONFIG_MPC83xx 1 /* MPC83xx family */
#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
#define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */
#define CONFIG_SYS_TEXT_BASE 0xFF800000
/*
* System Clock Setup
*/
#ifdef CONFIG_CLKIN_33MHZ
#define CONFIG_83XX_CLKIN 33333333
#define CONFIG_SYS_CLK_FREQ 33333333
#define CONFIG_PCI_33M 1
#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1
#else
#define CONFIG_83XX_CLKIN 66000000
#define CONFIG_SYS_CLK_FREQ 66000000
#define CONFIG_PCI_66M 1
#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1
#endif /* CONFIG_CLKIN_33MHZ */
/*
* Hardware Reset Configuration Word
*/
#define CONFIG_SYS_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\
HRCWL_CORE_TO_CSB_2X1 |\
HRCWL_CE_TO_PLL_1X15)
#define CONFIG_SYS_HRCW_HIGH (\
HRCWH_PCI_HOST |\
HRCWH_PCI1_ARBITER_ENABLE |\
HRCWH_PCICKDRV_ENABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0X00000100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT |\
HRCWH_SECONDARY_DDR_DISABLE |\
HRCWH_BIG_ENDIAN |\
HRCWH_LALE_EARLY)
/*
* System IO Config
*/
#define CONFIG_SYS_SICRH 0x00000000
#define CONFIG_SYS_SICRL 0x40000000
#define CONFIG_BOARD_EARLY_INIT_R
/*
* IMMR new address
*/
#define CONFIG_SYS_IMMR 0xE0000000
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#define CONFIG_SYS_83XX_DDR_USES_CS0
#define CONFIG_DDR_ECC /* support DDR ECC function */
#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
/*
* DDRCDR - DDR Control Driver Register
*/
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \
| DDRCDR_ODT \
| DDRCDR_Q_DRN)
/* 0x80080001 */
#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */
/*
* Manually set up DDR parameters
*/
#define CONFIG_DDR_II
#define CONFIG_SYS_DDR_SIZE 256 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
| CSCONFIG_ROW_BIT_13 \
| CSCONFIG_COL_BIT_10 \
| CSCONFIG_ODT_WR_ONLY_CURRENT)
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_ECC_EN)
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000
#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
#define CONFIG_SYS_DDR_INTERVAL ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \
| (1115 << SDRAM_INTERVAL_REFINT_SHIFT))
#define CONFIG_SYS_DDR_MODE 0x47800432
#define CONFIG_SYS_DDR_MODE2 0x8000c000
#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
(9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
(3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
(3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
(0 << TIMING_CFG0_WWT_SHIFT) | \
(0 << TIMING_CFG0_RRT_SHIFT) | \
(0 << TIMING_CFG0_WRT_SHIFT) | \
(0 << TIMING_CFG0_RWT_SHIFT))
#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_30) | \
(2 << TIMING_CFG1_WRTORD_SHIFT) | \
(2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
(3 << TIMING_CFG1_WRREC_SHIFT) | \
(10 << TIMING_CFG1_REFREC_SHIFT) | \
(3 << TIMING_CFG1_ACTTORW_SHIFT) | \
(8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
(3 << TIMING_CFG1_PRETOACT_SHIFT))
#define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
(4 << TIMING_CFG2_CKE_PLS_SHIFT) | \
(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
(2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
(0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
(0 << TIMING_CFG2_CPO_SHIFT))
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
/*
* Memory test
*/
#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
#define CONFIG_SYS_MEMTEST_END 0x00100000
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* FLASH base address */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR 0x00000000
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use intel Flash protection. */
/* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
| BR_PS_16 /* 16 bit port */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
| OR_UPM_XAM \
| OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV2 \
| OR_GPCM_XACS \
| OR_GPCM_SCY_15 \
| OR_GPCM_TRLX_SET \
| OR_GPCM_EHTR_SET \
| OR_GPCM_EAD)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */
#undef CONFIG_SYS_FLASH_CHECKSUM
/*
* NAND flash on the local bus
*/
#define CONFIG_SYS_NAND_BASE 0x60000000
#define CONFIG_CMD_NAND 1
#define CONFIG_NAND_FSL_UPM 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
/*
* [RFC] Comment said 4KB window; code said 256MB window; OR1 says 64MB
* ... What's correct?
*/
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_256MB)
/* Port size 8 bit, UPMA */
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \
| BR_PS_8 \
| BR_MS_UPMA \
| BR_V)
/* 0x60000881 */
#define CONFIG_SYS_OR1_PRELIM (OR_AM_64MB | OR_UPM_EAD)
/* 0xFC000001 */
/*
* Fujitsu MB86277 (MINT) graphics controller
*/
#define CONFIG_SYS_VIDEO_BASE 0x70000000
#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VIDEO_BASE
#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
/* Port size 32 bit, UPMB */
#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VIDEO_BASE \
| BR_PS_32 \
| BR_MS_UPMB \
| BR_V)
/* 0x000018a1 */
#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB | OR_UPM_EAD)
/* 0xFC000001 */
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
#ifdef CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_FSL_I2C
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* Don't probe these addrs */
#define CONFIG_SYS_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C2_OFFSET 0x3100
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_PCI
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_IO_BASE 0xE0300000
#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000
#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */
#ifdef CONFIG_PCI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
/*
* QE UEC ethernet configuration
*/
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME "UEC0"
#define CONFIG_UEC_ETH1 /* GETH1 */
#ifdef CONFIG_UEC_ETH1
#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE
#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9
#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR 2
#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID
#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
#endif
#define CONFIG_UEC_ETH2 /* GETH2 */
#ifdef CONFIG_UEC_ETH2
#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */
#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE
#define CONFIG_SYS_UEC2_TX_CLK QE_CLK4
#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR 4
#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID
#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
#endif
/*
* Environment
*/
#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE 0x20000
#else /* CONFIG_SYS_RAMBOOT */
#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif /* CONFIG_SYS_RAMBOOT */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_CMD_SAVEENV
#undef CONFIG_CMD_LOADS
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
mpc83xx: turn on icache in core initialization to improve u-boot boot time before, MPC8349ITX boots u-boot in 4.3sec: column1 is elapsed time since first message column2 is elapsed time since previous message column3 is the message 0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX 0.000 0.000: 0.000 0.000: Reset Status: 0.000 0.000: 0.032 0.032: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz 0.032 0.000: Board: Freescale MPC8349E-mITX 0.032 0.000: UPMA: Configured for compact flash 0.032 0.000: I2C: ready 0.061 0.028: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz) 1.516 1.456: FLASH: 16 MB 2.641 1.125: PCI: Bus Dev VenId DevId Class Int 2.652 0.011: 00 10 1095 3114 0180 00 2.652 0.000: PCI: Bus Dev VenId DevId Class Int 2.652 0.000: In: serial 2.652 0.000: Out: serial 2.652 0.000: Err: serial 2.682 0.030: Board revision: 1.0 (PCF8475A) 3.080 0.398: Net: TSEC1: No support for PHY id ffffffff; assuming generic 3.080 0.000: TSEC0, TSEC1 4.300 1.219: IDE: Bus 0: .** Timeout ** after, MPC8349ITX boots u-boot in 3.0sec: 0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX 0.010 0.000: 0.010 0.000: Reset Status: 0.010 0.000: 0.017 0.007: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz 0.017 0.000: Board: Freescale MPC8349E-mITX 0.038 0.020: UPMA: Configured for compact flash 0.038 0.000: I2C: ready 0.038 0.000: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz) 0.260 0.222: FLASH: 16 MB 1.390 1.130: PCI: Bus Dev VenId DevId Class Int 1.390 0.000: 00 10 1095 3114 0180 00 1.390 0.000: PCI: Bus Dev VenId DevId Class Int 1.400 0.010: In: serial 1.400 0.000: Out: serial 1.400 0.000: Err: serial 1.400 0.000: Board revision: 1.0 (PCF8475A) 1.832 0.432: Net: TSEC1: No support for PHY id ffffffff; assuming generic 1.832 0.000: TSEC0, TSEC1 3.038 1.205: IDE: Bus 0: .** Timeout ** also tested on these boards (albeit with a less accurate boottime measurement method): seconds: before after 8349MDS ~2.6 ~2.2 8360MDS ~2.8 ~2.6 8313RDB ~2.5 ~2.3 #nand boot 837xRDB ~3.1 ~2.3 also tested on an 8323ERDB. v2: also remove the delayed icache enablement assumption in arch ppc's board.c, and add a CONFIG_MPC83xx define in the ITX config file for consistency (even though it was already being defined in 83xx' config.mk). Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-04-21 00:37:54 +00:00
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
*/
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* IMMRBAR & PCI IO: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \
| BATU_BL_4M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* NAND: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_NAND_BASE \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_NAND_BASE \
| BATU_BL_64M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \
| BATU_BL_32M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR \
| BATL_PP_RW)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR \
| BATU_BL_128K \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_VIDEO_BASE \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_VIDEO_BASE \
| BATU_BL_64M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \
| BATL_PP_RW \
| BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#else /* CONFIG_PCI */
#define CONFIG_SYS_IBAT6L (0)
#define CONFIG_SYS_IBAT6U (0)
#define CONFIG_SYS_IBAT7L (0)
#define CONFIG_SYS_IBAT7U (0)
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#endif /* CONFIG_PCI */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Environment Configuration
*/
#define CONFIG_ENV_OVERWRITE
#if defined(CONFIG_UEC_ETH)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#define CONFIG_HAS_ETH3
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADADDR a00000
#define CONFIG_HOSTNAME mpc8360erdk
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_ROOTPATH "/nfsroot/"
#define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"loadaddr=a00000\0" \
"fdtaddr=900000\0" \
"fdtfile=mpc836x_rdk.dtb\0" \
"fsfile=fs\0" \
"ubootfile=u-boot.bin\0" \
"mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),"\
"-(rootfs)\0" \
"setbootargs=setenv bootargs console=$consoledev,$baudrate " \
"$mtdparts panic=1\0" \
"adddhcpargs=setenv bootargs $bootargs ip=on\0" \
"addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:" \
"$gatewayip:$netmask:$hostname:$netdev:off " \
"root=/dev/nfs rw nfsroot=$serverip:$rootpath\0" \
"addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 " \
"rootfstype=jffs2 rw\0" \
"tftp_get_uboot=tftp 100000 $ubootfile\0" \
"tftp_get_kernel=tftp $loadaddr $bootfile\0" \
"tftp_get_dtb=tftp $fdtaddr $fdtfile\0" \
"tftp_get_fs=tftp c00000 $fsfile\0" \
"nand_erase_kernel=nand erase 0 400000\0" \
"nand_erase_dtb=nand erase 400000 20000\0" \
"nand_erase_fs=nand erase 420000 3be0000\0" \
"nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0" \
"nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0" \
"nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0" \
"nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0" \
"nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0" \
"nor_reflash=protect off ff800000 ff87ffff ; " \
"erase ff800000 ff87ffff ; " \
"cp.b 100000 ff800000 $filesize\0" \
"nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel " \
"nand_write_kernel\0" \
"nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\
"nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0" \
"nand_reflash=run nand_reflash_kernel nand_reflash_dtb " \
"nand_reflash_fs\0" \
"boot_m=bootm $loadaddr - $fdtaddr\0" \
"dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\
"nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
"boot_m\0" \
"nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\
"boot_m\0" \
""
#define CONFIG_BOOTCOMMAND "run dhcpboot"
#endif /* __CONFIG_H */