u-boot/include/configs/hammerhead.h

162 lines
4.3 KiB
C
Raw Normal View History

/*
* Copyright (C) 2008 Miromico AG
*
* Configuration settings for the Miromico Hammerhead AVR32 board
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_AVR32
#define CONFIG_AT32AP
#define CONFIG_AT32AP7000
#define CONFIG_HAMMERHEAD
#define CONFIG_SYS_HZ 1000
/*
* Set up the PLL to run at 125 MHz, the CPU to run at the PLL
* frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
* and the PBA bus to run at 1/4 the PLL frequency.
*/
#define CONFIG_PLL
#define CONFIG_SYS_POWER_MANAGER
#define CONFIG_SYS_OSC0_HZ 25000000
#define CONFIG_SYS_PLL0_DIV 1
#define CONFIG_SYS_PLL0_MUL 5
#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16
#define CONFIG_SYS_CLKDIV_CPU 0
#define CONFIG_SYS_CLKDIV_HSB 1
#define CONFIG_SYS_CLKDIV_PBA 2
#define CONFIG_SYS_CLKDIV_PBB 1
/* Reserve VM regions for SDRAM and NOR flash */
#define CONFIG_SYS_NR_VM_REGIONS 2
/*
* The PLLOPT register controls the PLL like this:
* icp = PLLOPT<2>
* ivco = PLLOPT<1:0>
*
* We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
*/
#define CONFIG_SYS_PLL0_OPT 0x04
#define CONFIG_USART_BASE ATMEL_BASE_USART1
#define CONFIG_USART_ID 1
#define CONFIG_HOSTNAME hammerhead
/* User serviceable stuff */
#define CONFIG_DOS_PARTITION
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_STACKSIZE (2048)
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTARGS \
"console=ttyS0 root=mtd1 rootfstype=jffs2"
#define CONFIG_BOOTCOMMAND \
"fsload; bootm"
/*
* Only interrupt autoboot if <space> is pressed. Otherwise, garbage
* data on the serial line may interrupt the boot sequence.
*/
#define CONFIG_BOOTDELAY 1
#define CONFIG_AUTOBOOT
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_PROMPT \
"Press SPACE to abort autoboot in %d seconds\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR "d"
#define CONFIG_AUTOBOOT_STOP_STR " "
/*
* After booting the board for the first time, new ethernet address
* should be generated and assigned to the environment variables
* "ethaddr". This is normally done during production.
*/
#define CONFIG_OVERWRITE_ETHADDR_ONCE
/*
* BOOTP/DHCP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MMC
#undef CONFIG_CMD_FPGA
#undef CONFIG_CMD_SETGETDCR
#define CONFIG_ATMEL_USART
#define CONFIG_MACB
#define CONFIG_PORTMUX_PIO
#define CONFIG_SYS_NR_PIOS 5
#define CONFIG_SYS_HSDRAMC
#define CONFIG_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#define CONFIG_GENERIC_MMC
#define CONFIG_SYS_DCACHE_LINESZ 32
#define CONFIG_SYS_ICACHE_LINESZ 32
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_BASE 0x00000000
#define CONFIG_SYS_FLASH_SIZE 0x800000
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 135
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_TEXT_BASE 0x00000000
#define CONFIG_SYS_INTRAM_BASE 0x24000000
#define CONFIG_SYS_INTRAM_SIZE 0x8000
#define CONFIG_SYS_SDRAM_BASE 0x10000000
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SIZE 65536
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
#define CONFIG_SYS_MALLOC_LEN (256*1024)
#define CONFIG_SYS_DMA_ALLOC_LEN (16384)
/* Allow 4MB for the kernel run-time image */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x00400000)
#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024)
/* Other configuration settings that shouldn't have to change all that often */
#define CONFIG_SYS_PROMPT "Hammerhead> "
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x1f00000)
#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
#endif /* __CONFIG_H */