u-boot/include/configs/pf5200.h

405 lines
13 KiB
C
Raw Normal View History

/*
* (C) Copyright 2003-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*************************************************************************
* (c) 2005 esd gmbh Hannover
*
*
* from IceCube.h file
* by Reinhard Arlt reinhard.arlt@esd-electronics.com
*
*************************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC5200 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_ICECUBE 1 /* ... on IceCube board */
#define CONFIG_PF5200 1 /* ... on PF5200 board */
#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#if 0 /* test-only */
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#else
#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */
#endif
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */
/*
* PCI Mapping:
* 0x40000000 - 0x4fffffff - PCI Memory
* 0x50000000 - 0x50ffffff - PCI IO Space
*/
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_MEM_SIZE 0x10000000
#define CONFIG_PCI_IO_BUS 0x50000000
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
2005-10-28 20:30:33 +00:00
#define CONFIG_MII 1
#if 0 /* test-only !!! */
#define CONFIG_NET_MULTI 1
#define CONFIG_EEPRO100 1
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
#endif
#endif
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
/* USB */
#if 0
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
#endif
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_BSP
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IDE
#ifdef CONFIG_MPC5200
#define CONFIG_CMD_PCI
#endif
#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
# define CONFIG_SYS_LOWBOOT 1
# define CONFIG_SYS_LOWBOOT16 1
#endif
#if (TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
# define CONFIG_SYS_LOWBOOT 1
# define CONFIG_SYS_LOWBOOT08 1
#endif
/*
* Autobooting
*/
#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
"echo Welcome to ParaFinder pf5200;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \
"flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \
"net_vxworks=phypower 1;sleep 2;tftp ${loadaddr} ${image};run vxworks_args;bootvx\0" \
"vxworks_args=setenv bootargs fec(0,0)${host}:${image} h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script}\0" \
"ata_vxworks_args=setenv bootargs /ata0/vxWorks h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script} o=fec0 \0" \
"loadaddr=01000000\0" \
"serverip=192.168.2.99\0" \
"gatewayip=10.0.0.79\0" \
"user=mu\0" \
"target=pf5200.esd\0" \
"script=pf5200.bat\0" \
"image=/tftpboot/vxWorks_pf5200\0" \
"ipaddr=10.0.13.196\0" \
"netmask=255.255.0.0\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_vxworks0"
#if defined(CONFIG_MPC5200)
/*
* IPB Bus clocking configuration.
*/
#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
#define CONFIG_SYS_I2C_MULTI_EEPROMS 1
/*
* Flash configuration
*/
#define CONFIG_SYS_FLASH_BASE 0xFE000000
#define CONFIG_SYS_FLASH_SIZE 0x02000000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
/*
* Environment settings
*/
#if 1 /* test-only */
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SIZE 0x10000
#define CONFIG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_OVERWRITE 1
#else
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars */
/* total size of a CAT24WC32 is 8192 bytes */
#define CONFIG_ENV_OVERWRITE 1
#endif
/*
* Memory map
*/
#define CONFIG_SYS_MBAR 0xF0000000
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
/* Use SRAM until RAM will be available */
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
# define CONFIG_SYS_RAMBOOT 1
#endif
#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_MPC5xxx_FEC_MII100
/*
* Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
*/
/* #define CONFIG_MPC5xxx_FEC_MII10 */
#define CONFIG_PHY_ADDR 0x00
#define CONFIG_UDP_CHECKSUM 1
/*
* GPIO configuration
*/
#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Various low-level settings
*/
#if defined(CONFIG_MPC5200)
#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
#define CONFIG_SYS_HID0_FINAL HID0_ICE
#else
#define CONFIG_SYS_HID0_INIT 0
#define CONFIG_SYS_HID0_FINAL 0
#endif
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_BOOTCS_CFG 0x0004DD00
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
#define CONFIG_SYS_CS1_START 0xfd000000
#define CONFIG_SYS_CS1_SIZE 0x00010000
#define CONFIG_SYS_CS1_CFG 0x10101410
#define CONFIG_SYS_CS_BURST 0x00000000
#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
#define CONFIG_SYS_RESET_ADDRESS 0xff000000
/*-----------------------------------------------------------------------
* USB stuff
*-----------------------------------------------------------------------
*/
#define CONFIG_USB_CLOCK 0x0001BBBB
#define CONFIG_USB_CONFIG 0x00001000
/*-----------------------------------------------------------------------
* IDE/ATA stuff Supports IDE harddisk
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_IDE_RESET /* reset for ide supported */
#define CONFIG_IDE_PREINIT
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
#define CONFIG_SYS_ATA_STRIDE 4
/*-----------------------------------------------------------------------
* CPLD stuff
*/
#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
/* CPLD program pin configuration */
#define CONFIG_SYS_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */
#define CONFIG_SYS_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */
#define CONFIG_SYS_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */
#define CONFIG_SYS_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */
#define JTAG_GPIO_ADDR_TMS (CONFIG_SYS_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */
#define JTAG_GPIO_ADDR_TCK (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */
#define JTAG_GPIO_ADDR_TDI (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */
#define JTAG_GPIO_ADDR_TDO (CONFIG_SYS_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */
#define JTAG_GPIO_ADDR_CFG (CONFIG_SYS_MBAR + 0xB00)
#define JTAG_GPIO_CFG_SET 0x00000000
#define JTAG_GPIO_CFG_RESET 0x00F00000
#define JTAG_GPIO_ADDR_EN_TMS (CONFIG_SYS_MBAR + 0xB04)
#define JTAG_GPIO_TMS_EN_SET 0x20000000 /* Enable for GPIO */
#define JTAG_GPIO_TMS_EN_RESET 0x00000000
#define JTAG_GPIO_ADDR_DDR_TMS (CONFIG_SYS_MBAR + 0xB0C)
#define JTAG_GPIO_TMS_DDR_SET 0x20000000 /* Set as output */
#define JTAG_GPIO_TMS_DDR_RESET 0x00000000
#define JTAG_GPIO_ADDR_EN_TCK (CONFIG_SYS_MBAR + 0xC00)
#define JTAG_GPIO_TCK_EN_SET 0x20000000 /* Enable for GPIO */
#define JTAG_GPIO_TCK_EN_RESET 0x00000000
#define JTAG_GPIO_ADDR_DDR_TCK (CONFIG_SYS_MBAR + 0xC08)
#define JTAG_GPIO_TCK_DDR_SET 0x20000000 /* Set as output */
#define JTAG_GPIO_TCK_DDR_RESET 0x00000000
#define JTAG_GPIO_ADDR_EN_TDI (CONFIG_SYS_MBAR + 0xC00)
#define JTAG_GPIO_TDI_EN_SET 0x10000000 /* Enable as GPIO */
#define JTAG_GPIO_TDI_EN_RESET 0x00000000
#define JTAG_GPIO_ADDR_DDR_TDI (CONFIG_SYS_MBAR + 0xC08)
#define JTAG_GPIO_TDI_DDR_SET 0x10000000 /* Set as output */
#define JTAG_GPIO_TDI_DDR_RESET 0x00000000
#define JTAG_GPIO_ADDR_EN_TDO (CONFIG_SYS_MBAR + 0xB04)
#define JTAG_GPIO_TDO_EN_SET 0x10000000 /* Enable as GPIO */
#define JTAG_GPIO_TDO_EN_RESET 0x00000000
#define JTAG_GPIO_ADDR_DDR_TDO (CONFIG_SYS_MBAR + 0xB0C)
#define JTAG_GPIO_TDO_DDR_SET 0x00000000
#define JTAG_GPIO_TDO_DDR_RESET 0x10000000 /* Set as input */
#endif /* __CONFIG_H */