u-boot/include/configs/TOP5200.h

419 lines
12 KiB
C
Raw Normal View History

/*
* (C) Copyright 2003
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* modified for TOP5200-series by Reinhard Meyer, www.emk-elektronik.de
*
* TOP5200 differences from IceCube:
* 1 FLASH Bank for one Chip only, up to 64 MB in 16 MB Banks
* bank switch controlled by TIMER_6(LSB) and TIMER_7(MSB) Pins
* 1 SDRAM/DDRAM Bank up to 256 MB
* local VPD I2C Bus is software driven and uses
* GPIO_WKUP_6 for SDA, GPIO_WKUP_7 for SCL
* FLASH is re-located at 0xff000000
* Internal regs are at 0xf0000000
* Reset jumps to 0x00000100
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
#define CONFIG_MPC5200 1 /* More exactly a MPC5200 */
#define CONFIG_TOP5200 1 /* ... on TOP5200 board - we need this for FEC.C */
#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Serial console configuration
*/
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200)
/*
* PCI Mapping:
* 0x40000000 - 0x4fffffff - PCI Memory
* 0x50000000 - 0x50ffffff - PCI IO Space
*/
# define CONFIG_PCI 1
# define CONFIG_PCI_PNP 1
# define CONFIG_PCI_SCAN_SHOW 1
# define CONFIG_PCI_MEM_BUS 0x40000000
# define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
# define CONFIG_PCI_MEM_SIZE 0x10000000
# define CONFIG_PCI_IO_BUS 0x50000000
# define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
# define CONFIG_PCI_IO_SIZE 0x01000000
# define ADD_PCI_CMD CFG_CMD_PCI
#else /* no Evaluation board */
# define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */
#endif
/* USB */
#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200)
# define CONFIG_USB_OHCI
# define CONFIG_USB_CLOCK 0x0001bbbb
# if defined (CONFIG_EVAL5200)
# define CONFIG_USB_CONFIG 0x00005100
# else
# define CONFIG_USB_CONFIG 0x00001000
# endif
# define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
# define CONFIG_DOS_PARTITION
# define CONFIG_USB_STORAGE
#else
# define ADD_USB_CMD 0
#endif
/* IDE */
#if defined (CONFIG_EVAL5200) || defined (CONFIG_LITE5200)
# define ADD_IDE_CMD CFG_CMD_IDE | CFG_CMD_FAT
# define CONFIG_DOS_PARTITION
#else
# define ADD_IDE_CMD 0
#endif
/*
* Supported commands
*/
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
ADD_PCI_CMD | \
ADD_USB_CMD | \
2004-03-25 15:14:43 +00:00
ADD_IDE_CMD | \
CFG_CMD_ASKENV | \
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_I2C | \
CFG_CMD_EEPROM | \
CFG_CMD_REGINFO | \
CFG_CMD_IMMAP | \
CFG_CMD_ELF | \
CFG_CMD_MII | \
CFG_CMD_BEDBUG \
)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*
* MUST be low boot - HIGHBOOT is not supported anymore
*/
#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
# define CFG_LOWBOOT 1
# define CFG_LOWBOOT16 1
#else
# error "TEXT_BASE must be 0xff000000"
#endif
/*
* Autobooting
*/
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=$(serverip):$(rootpath)\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs $(bootargs) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
":$(hostname):$(netdev):off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
"bootm $(kernel_addr)\0" \
"flash_self=run ramargs addip;" \
"bootm $(kernel_addr) $(ramdisk_addr)\0" \
"net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
"rootpath=/opt/eldk/ppc_82xx\0" \
"bootfile=/tftpboot/MPC5200/uImage\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
/*
* IPB Bus clocking configuration.
*/
#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
/*
* I2C configuration
*/
/*
* EEPROM configuration
*/
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 70
#define CFG_I2C_EEPROM_ADDR_LEN 2
#define CFG_EEPROM_SIZE 0x2000
#define CONFIG_ENV_OVERWRITE
#define CONFIG_MISC_INIT_R
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C with softwate support */
#if defined (CONFIG_SOFT_I2C)
# define SDA0 0x40
# define SCL0 0x80
# define GPIOE0 *((volatile uchar*)(CFG_MBAR+0x0c00))
# define DDR0 *((volatile uchar*)(CFG_MBAR+0x0c08))
# define DVO0 *((volatile uchar*)(CFG_MBAR+0x0c0c))
# define DVI0 *((volatile uchar*)(CFG_MBAR+0x0c20))
# define ODE0 *((volatile uchar*)(CFG_MBAR+0x0c04))
# define I2C_INIT {GPIOE0|=(SDA0|SCL0);ODE0|=(SDA0|SCL0);DVO0|=(SDA0|SCL0);DDR0|=(SDA0|SCL0);}
# define I2C_READ ((DVI0&SDA0)?1:0)
# define I2C_SDA(x) {if(x)DVO0|=SDA0;else DVO0&=~SDA0;}
# define I2C_SCL(x) {if(x)DVO0|=SCL0;else DVO0&=~SCL0;}
# define I2C_DELAY {udelay(5);}
# define I2C_ACTIVE {DDR0|=SDA0;}
# define I2C_TRISTATE {DDR0&=~SDA0;}
# define CFG_I2C_SPEED 100000
# define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_FACT_ADDR 0x57
#endif
#if defined (CONFIG_HARD_I2C)
# define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
# define CFG_I2C_SPEED 100000 /* 100 kHz */
# define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_EEPROM_ADDR 0x54
#define CFG_I2C_FACT_ADDR 0x54
#endif
/*
* Flash configuration, expect one 16 Megabyte Bank at most
*/
#define CFG_FLASH_BASE 0xff000000
#define CFG_FLASH_SIZE 0x01000000
#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0)
#define CFG_MAX_FLASH_SECT 256 /* max num of sects on one chip */
#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */
/*
* DRAM configuration - will be read from VPD later... TODO!
*/
#if 0
/* 2x MT48LC16M16A2 - 7.0 ns SDRAMS = 64 MegaBytes Total */
#define CFG_DRAM_DDR 0
#define CFG_DRAM_EMODE 0
#define CFG_DRAM_MODE 0x008D
#define CFG_DRAM_CONTROL 0x514F0000
#define CFG_DRAM_CONFIG1 0xC2233A00
#define CFG_DRAM_CONFIG2 0x88B70004
#define CFG_DRAM_TAP_DEL 0x08
#define CFG_DRAM_RAM_SIZE 0x19
#endif
#if 1
/* 2x MT48LC16M16A2 - 7.5 ns SDRAMS = 64 MegaBytes Total */
#define CFG_DRAM_DDR 0
#define CFG_DRAM_EMODE 0
#define CFG_DRAM_MODE 0x00CD
#define CFG_DRAM_CONTROL 0x514F0000
#define CFG_DRAM_CONFIG1 0xD2333A00
#define CFG_DRAM_CONFIG2 0x8AD70004
#define CFG_DRAM_TAP_DEL 0x08
#define CFG_DRAM_RAM_SIZE 0x19
#endif
/*
* Environment settings
*/
#define CFG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */
#define CFG_ENV_OFFSET 0x1000
#define CFG_ENV_SIZE 0x0700
/*
* VPD settings
*/
#define CFG_FACT_OFFSET 0x1800
#define CFG_FACT_SIZE 0x0800
/*
* Memory map
*
* Warning!!! with the current BestComm Task, MBAR MUST BE set to 0xf0000000
*/
#define CFG_MBAR 0xf0000000 /* DO NOT CHANGE this */
#define CFG_SDRAM_BASE 0x00000000
#define CFG_DEFAULT_MBAR 0x80000000
/* Use SRAM until RAM will be available */
#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_BASE TEXT_BASE
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
# define CFG_RAMBOOT 1
#endif
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
*/
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_FEC_10MBIT 1 /* Workaround for FEC 100Mbit problem */
#define CONFIG_PHY_ADDR 0x1f
#define CONFIG_PHY_TYPE 0x79c874
/*
* GPIO configuration:
* PSC1,2,3 predefined as UART
* PCI disabled
* Ethernet 100 with MD
*/
#define CFG_GPS_PORT_CONFIG 0x00058044
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x01f00000 /* 1 ... 31 MB in DRAM */
#define CFG_LOAD_ADDR 0x200000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#ifdef CONFIG_EVAL5200 /* M48T08 is available with the Evaluation board only */
#define CONFIG_RTC_MK48T59 1 /* use M48T08 on EVAL5200 */
#define RTC(reg) (0xf0010000+reg)
/* setup CS2 for M48T08. Must MAP 64kB */
#define CFG_CS2_START RTC(0)
#define CFG_CS2_SIZE 0x10000
/* setup CS2 configuration register: */
/* WaitP = 0, WaitX = 4, MX=0, AL=1, AA=1, CE=1 */
/* AS=2, DS=0, Bank=0, WTyp=0, WS=0, RS=0, WO=0, RO=0 */
#define CFG_CS2_CFG 0x00047800
#else
#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
#endif
/*
* Various low-level settings
*/
#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
#define CFG_HID0_FINAL HID0_ICE
#define CFG_BOOTCS_START CFG_FLASH_BASE
#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
#define CFG_BOOTCS_CFG 0x00047801
#define CFG_CS0_START CFG_FLASH_BASE
#define CFG_CS0_SIZE CFG_FLASH_SIZE
#define CFG_CS_BURST 0x00000000
#define CFG_CS_DEADCYCLE 0x33333333
#define CFG_RESET_ADDRESS 0x7f000000
/*-----------------------------------------------------------------------
* IDE/ATA stuff Supports IDE harddisk
*-----------------------------------------------------------------------
*/
#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#define CONFIG_IDE_RESET 1
#define CONFIG_IDE_PREINIT
#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
#define CFG_ATA_IDE0_OFFSET 0x0000
#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
#define CFG_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
/* Offset for alternate registers */
#define CFG_ATA_ALT_OFFSET (0x005c)
/* Interval between registers */
#define CFG_ATA_STRIDE 4
#endif /* __CONFIG_H */