u-boot/include/configs/bf561-acvilon.h

171 lines
4.1 KiB
C
Raw Normal View History

/*
* U-boot - Configuration file for BF561 Acvilon System On Module
* For more information please go to http://www.niistt.ru/
*/
#ifndef __CONFIG_BF561_ACVILON_H__
#define __CONFIG_BF561_ACVILON_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 12000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 50
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
/*
* Memory Settings
*/
#define CONFIG_MEM_ADD_WDTH 10
#define CONFIG_MEM_SIZE 128
#define CONFIG_EBIU_SDRRC_VAL 0x300
#define CONFIG_EBIU_SDGCTL_VAL 0x00B11189
#define CONFIG_EBIU_AMGCTL_VAL 0x4e
#define CONFIG_EBIU_AMBCTL0_VAL 0xffc2ffc2
#define CONFIG_EBIU_AMBCTL1_VAL 0x99b35554
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
/*
* RTC Settings
*/
#define CONFIG_RTC_DS1337
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
#define CONFIG_SYS_I2C_DTT_ADDR 0x49
/*#define CONFIG_SYS_DTT_MAX_TEMP 70
#define CONFIG_SYS_DTT_LOW_TEMP -30
#define CONFIG_SYS_DTT_HYSTERESIS 3*/
/*
* Network Settings
*/
#define ADI_CMDS_NETWORK 1
#define CONFIG_NET_MULTI
#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DTT
#if defined(CONFIG_CMD_NET)
#define CONFIG_SMC911X 1
#define CONFIG_SMC911X_32_BIT
/* #define CONFIG_SMC911X_16_BIT */
#define CONFIG_SMC911X_BASE 0x28000000
#endif /* (CONFIG_CMD_NET) */
#define CONFIG_HOSTNAME bf561-acvilon
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
* Flash Settings
*/
#define CONFIG_SYS_NO_FLASH
/*
* I2C Settings
*/
#define CONFIG_HARD_I2C
/* Use 300kHz speed by default */
#define CONFIG_SYS_I2C_SPEED 0x00
#define CONFIG_PCA9564_I2C
#define CONFIG_PCA9564_BASE 0x2c000000
/*
* SPI Settings
*/
#define CONFIG_BFIN_SPI
#define CONFIG_ENV_SPI_MAX_HZ 10000000
#define CONFIG_SF_DEFAULT_SPEED 10000000
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_ATMEL
/*
* Env Storage Settings
*/
#define CONFIG_ENV_IS_IN_SPI_FLASH
/* #define CONFIG_CMD_SAVEENV */
#define CONFIG_ENV_SECT_SIZE (1056 * 8)
#define CONFIG_ENV_OFFSET ((16 + 256) * 1056)
#define CONFIG_ENV_SIZE (8 * 1056)
/*
* NAND Settings
* We're using NAND_PLAT driver to make things simplier
*/
#define CONFIG_NAND_PLAT
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BASE 0x24000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2))
#define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 3))
#define BFIN_NAND_WRITE(addr, cmd) \
do { \
bfin_write8(addr, cmd); \
SSYNC(); \
} while (0)
#define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd)
#define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd)
#define NAND_PLAT_GPIO_DEV_READY GPIO_PF10
/*
* Misc Settings
*/
#define CONFIG_UART_CONSOLE 0
#define CONFIG_BAUDRATE 57600
#define CONFIG_SYS_PROMPT "Acvilon> "
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif /* __CONFIG_BF561_ACVILON_H__ */