u-boot/configs/am43xx_evm_qspiboot_defconfig

45 lines
1008 B
Plaintext
Raw Normal View History

CONFIG_ARM=y
CONFIG_AM43XX=y
CONFIG_TARGET_AM43XX_EVM=y
ti: AM43xx: Use CONFIG options from SOC Kconfig Updates configs/am43xx_evm.h to use CONFIG options from SOC specific Kconfig file for various calculations. On AM43x devices, the address of SPL entry point depends on the device type, i.e. whether it is secure or non-secure. Further, for non-secure devices, the SPL entry point is different between USB HOST boot mode, other "memory" boot modes (MMC, NAND) and "peripheral" boot modes (UART, USB) To add to the complexity, on secure devices, in addition to the above differences, the SPL entry point can change because of the space occupied by other components (other than u-boot or spl) that go into a secure boot image. To prevent the user from having to modify source files every time any component of the secure image changes, the value of CONFIG_SPL_TEXT_BASE has been set using a Kconfig option that is supplied in the am43xx_*_defconfig files Using the CONFIG options also enables us to do away with some compile time flags that were used to specify CONFIG_SPL_TEXT_BASE for different boot modes. On QSPI devices, the same problem described above occurs w.r.t. the address of the u-boot entry point in flash, when booting secure devices. To handle this, CONFIG_SYS_TEXT_BASE is also setup via a Kconfig option and the defconfig files. Signed-off-by: Madan Srinivas <madans@ti.com> Signed-off-by: Daniel Allred <d-allred@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-20 00:10:47 +00:00
CONFIG_ISW_ENTRY_ADDR=0x30000000
CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,QSPI,QSPI_BOOT"
CONFIG_QSPI_BOOT=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_ASKENV=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
CONFIG_CMD_I2C=y
CONFIG_CMD_USB=y
CONFIG_CMD_DFU=y
CONFIG_CMD_GPIO=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SYS_NS16550=y
CONFIG_TI_QSPI=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
CONFIG_USB_DWC3=y
CONFIG_USB_DWC3_GADGET=y
CONFIG_USB_DWC3_OMAP=y
CONFIG_USB_DWC3_PHY_OMAP=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_G_DNL_MANUFACTURER="Texas Instruments"
CONFIG_G_DNL_VENDOR_NUM=0x0403
CONFIG_G_DNL_PRODUCT_NUM=0xbd00
CONFIG_OF_LIBFDT=y