u-boot/include/configs/thuban.h

98 lines
2.1 KiB
C
Raw Normal View History

/*
* (C) Copyright 2013 Siemens Schweiz AG
* (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* U-Boot file:/include/configs/am335x_evm.h
*
* Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_THUBAN_H
#define __CONFIG_THUBAN_H
#include "siemens-am33x-common.h"
#define CONFIG_SYS_MPUCLK 300
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
#define DDR_PLL_FREQ 303
#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#define BOARD_DFU_BUTTON_GPIO 27 /* Use as default */
#define GPIO_LAN9303_NRST 88 /* GPIO2_24 = gpio88 */
#define CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
"button_dfu0=27\0" \
"led0=103,1,0\0" \
"led1=64,0,1\0"
#undef CONFIG_DOS_PARTITION
#define CONFIG_BOARD_LATE_INIT
/* Physical Memory Map */
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
/* I2C Configuration */
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define EEPROM_ADDR_DDR3 0x90
#define EEPROM_ADDR_CHIP 0x120
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300
#undef CONFIG_MII
#undef CONFIG_PHY_GIGE
#define CONFIG_PHY_SMSC
#define CONFIG_FACTORYSET
/* Watchdog */
#define CONFIG_OMAP_WATCHDOG
/* Define own nand partitions */
#define CONFIG_ENV_OFFSET_REDUND 0x2E0000
#define CONFIG_ENV_SIZE_REDUND 0x2000
#define CONFIG_ENV_RANGE (4 * CONFIG_SYS_ENV_SECT_SIZE)
#define MTDPARTS_DEFAULT MTDPARTS_DEFAULT_V2
#ifndef CONFIG_SPL_BUILD
/* Default env settings */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hostname=thuban\0" \
"ubi_off=2048\0"\
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"nand_img_size=0x400000\0" \
"optargs=\0" \
"preboot=draco_led 0\0" \
CONFIG_ENV_SETTINGS_BUTTONS_AND_LEDS \
CONFIG_ENV_SETTINGS_V2 \
CONFIG_ENV_SETTINGS_NAND_V2
#ifndef CONFIG_RESTORE_FLASH
/* set to negative value for no autoboot */
#define CONFIG_BOOTCOMMAND \
"if dfubutton; then " \
"run dfu_start; " \
"reset; " \
"fi;" \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"run nand_boot;" \
"run nand_boot_backup;" \
arm, am335x: update for the siemens boards - dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
2013-11-04 13:05:03 +00:00
"reset;"
#else
#define CONFIG_BOOTCOMMAND \
"setenv autoload no; " \
"dhcp; " \
"if tftp 80000000 debrick.scr; then " \
"source 80000000; " \
"fi"
#endif
#endif /* CONFIG_SPL_BUILD */
#endif /* ! __CONFIG_THUBAN_H */