u-boot/board/palmtreo680/palmtreo680.c

149 lines
3.7 KiB
C
Raw Normal View History

pxa: add support for palmtreo680 board This patch adds support for the Palm Treo 680 smartphone. A quick overview of u-boot implementation on the treo 680... The treo 680 has a Diskonchip G4 nand flash chip. This device has a 2k region that maps to the system bus at the reset vector in a NOR-like fashion so that it can be used as the boot device. The phone is shipped with this 2k region configured as write-protected (can't be modified) and programmed with an initial program loader (IPL). At power-up, this IPL loads the contents of two flash blocks to SDRAM and jumps to it. The capacity of the two blocks is not large enough to hold all of u-boot, so a u-boot SPL is used. To conserve flash space, these two blocks and the necessary number of subsequent blocks are programmed with a concatenated spl + u-boot image. That way, the IPL will also load a portion of u-boot proper, and when the spl runs, it relocates the portion of u-boot that the IPL has already loaded, and then resumes loading the remaining part of u-boot before jumping to it. The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think that having a writable environment was worth the cost of a flash block, although adding it would be straightforward. I abuse the CONFIG_EXTRA_ENV_SETTINGS option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV). Support for the LCD is included, but currently it is only useful for displaying the u-boot splash screen. But if u-boot is built without the usbtty console, it does display the auto-boot progress nicely. Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-18 18:08:50 +00:00
/*
* Palm Treo 680 Support
*
* Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
*
* This file is released under the terms of GPL v2 and any later version.
* See the file COPYING in the root directory of the source tree for details.
*
*/
#include <common.h>
#include <command.h>
#include <serial.h>
#include <nand.h>
#include <malloc.h>
#include <asm/arch/pxa-regs.h>
#include <asm/arch-pxa/pxa.h>
#include <asm/arch-pxa/regs-mmc.h>
#include <asm/io.h>
#include <asm/global_data.h>
#include <u-boot/crc.h>
#include <linux/mtd/docg4.h>
DECLARE_GLOBAL_DATA_PTR;
static struct nand_chip docg4_nand_chip;
int board_init(void)
{
/* We have RAM, disable cache */
dcache_disable();
icache_disable();
gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
gd->bd->bi_boot_params = CONFIG_SYS_DRAM_BASE + 0x100;
return 0;
}
int dram_init(void)
{
/* IPL initializes SDRAM (we're already running from it) */
gd->ram_size = PHYS_SDRAM_1_SIZE;
return 0;
}
#ifdef CONFIG_LCD
void lcd_enable(void)
{
/*
* Undo the L_BIAS / gpio77 pin configuration performed by the pxa lcd
* driver code. We need it as an output gpio.
*/
writel((readl(GAFR2_L) & ~(0xc << 24)), GAFR2_L);
/* power-up and enable the lcd */
writel(0x00400000, GPSR(86)); /* enable; drive high */
writel(0x00002000, GPSR(77)); /* power; drive high */
writel(0x02000000, GPCR(25)); /* enable_n; drive low */
/* turn on LCD backlight and configure PWM for reasonable brightness */
writel(0x00, PWM_CTRL0);
writel(0x1b1, PWM_PERVAL0);
writel(0xfd, PWM_PWDUTY0);
writel(0x00000040, GPSR(38)); /* backlight power on */
}
#endif
#ifdef CONFIG_MMC
int board_mmc_init(bd_t *bis)
{
writel(1 << 10, GPSR(42)); /* power on */
return pxa_mmc_register(0);
}
#endif
void board_nand_init(void)
{
/* we have one 128M diskonchip G4 */
struct mtd_info *mtd = &nand_info[0];
struct nand_chip *nand = &docg4_nand_chip;
if (docg4_nand_init(mtd, nand, 0))
hang();
}
#ifdef CONFIG_SPL_BUILD
void nand_boot(void)
{
__attribute__((noreturn)) void (*uboot)(void);
extern const void *_start, *_end; /* boundaries of spl in memory */
/* size of spl; ipl loads this, and then a portion of u-boot */
const size_t spl_image_size = ((size_t)&_end - (size_t)&_start);
/* the flash offset of the blocks that are loaded by the spl */
const uint32_t spl_load_offset = CONFIG_SYS_NAND_U_BOOT_OFFS +
DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_SIZE;
/* total number of bytes loaded by IPL */
const size_t ipl_load_size =
DOCG4_IPL_LOAD_BLOCK_COUNT * DOCG4_BLOCK_CAPACITY_SPL;
/* number of bytes of u-boot proper that was loaded by the IPL */
const size_t ipl_uboot_load_size = ipl_load_size - spl_image_size;
/* number of remaining bytes of u-boot that the SPL must load */
const size_t spl_load_size =
CONFIG_SYS_NAND_U_BOOT_SIZE - ipl_load_size;
/* memory address where we resume loading u-boot */
void *const load_addr =
(void *)(CONFIG_SYS_NAND_U_BOOT_DST + ipl_uboot_load_size);
/*
* Copy the portion of u-boot already read from flash by the IPL to its
* correct load address.
*/
memcpy((void *)CONFIG_SYS_NAND_U_BOOT_DST, &_end, ipl_uboot_load_size);
/*
* Resume loading u-boot where the IPL left off.
*/
nand_spl_load_image(spl_load_offset, spl_load_size, load_addr);
#ifdef CONFIG_NAND_ENV_DST
nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
(void *)CONFIG_NAND_ENV_DST);
#ifdef CONFIG_ENV_OFFSET_REDUND
nand_spl_load_image(CONFIG_ENV_OFFSET_REDUND, CONFIG_ENV_SIZE,
(void *)CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE);
#endif
#endif
/*
* Jump to U-Boot image
*/
uboot = (void *)CONFIG_SYS_NAND_U_BOOT_START;
(*uboot)();
}
void board_init_f(ulong bootflag)
{
nand_boot();
}
#endif /* CONFIG_SPL_BUILD */