u-boot/drivers/mtd/cfi_flash.c

2482 lines
63 KiB
C
Raw Normal View History

/*
* (C) Copyright 2002-2004
* Brad Kemp, Seranoa Networks, Brad.Kemp@seranoa.com
*
* Copyright (C) 2003 Arabella Software Ltd.
* Yuli Barcohen <yuli@arabellasw.com>
*
* Copyright (C) 2004
* Ed Okerson
*
* Copyright (C) 2006
* Tolunay Orkun <listmember@orkun.us>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/* The DEBUG define must be before common to enable debugging */
/* #define DEBUG */
#include <common.h>
#include <console.h>
#include <dm.h>
#include <errno.h>
#include <fdt_support.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <asm/byteorder.h>
#include <asm/unaligned.h>
#include <environment.h>
#include <mtd/cfi_flash.h>
#include <watchdog.h>
/*
* This file implements a Common Flash Interface (CFI) driver for
* U-Boot.
*
* The width of the port and the width of the chips are determined at
* initialization. These widths are used to calculate the address for
* access CFI data structures.
*
* References
* JEDEC Standard JESD68 - Common Flash Interface (CFI)
* JEDEC Standard JEP137-A Common Flash Interface (CFI) ID Codes
* Intel Application Note 646 Common Flash Interface (CFI) and Command Sets
* Intel 290667-008 3 Volt Intel StrataFlash Memory datasheet
* AMD CFI Specification, Release 2.0 December 1, 2001
* AMD/Spansion Application Note: Migration from Single-byte to Three-byte
* Device IDs, Publication Number 25538 Revision A, November 8, 2001
*
* Define CONFIG_SYS_WRITE_SWAPPED_DATA, if you have to swap the Bytes between
* reading and writing ... (yes there is such a Hardware).
*/
DECLARE_GLOBAL_DATA_PTR;
static uint flash_offset_cfi[2] = { FLASH_OFFSET_CFI, FLASH_OFFSET_CFI_ALT };
#ifdef CONFIG_FLASH_CFI_MTD
static uint flash_verbose = 1;
#else
#define flash_verbose 1
#endif
flash_info_t flash_info[CFI_MAX_FLASH_BANKS]; /* FLASH chips info */
Major CFI-FLASH driver update: * Add env-variable "unlock" to handle initial state of sectors (locked/unlocked). Only the U-Boot image and it's environment is protected, all other sectors are unprotected (unlocked) if flash hardware protection is used (CFG_FLASH_PROTECTION) and the environment variable "unlock" is set to "yes". Patch by Stefan Roese, 28 Feb 2006 * Update drivers/cfi_flash.c: - find_sector() called in both versions of flash_write_cfiword() Patch by Peter Pearse, 27th Feb 2006 * CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode Patch by Jose Maria Lopez, 16 Jan 2006 * Add support for AMD/Spansion Flashes in flash_write_cfibuffer Patch by Alex Bastos and Thomas Schaefer, 2005-08-29 * Changes/fixes for drivers/cfi_flash.c: We *should* check if there are any error bits if the previous call returned ERR_OK (Otherwise we will have output an error message in flash_status_check() already.) The original code would only check for error bits if flash_status_check() returns ERR_TIMEOUT. Patch by Marcus Hall, 23 Aug 2005 * Changes/fixes for drivers/cfi_flash.c: - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c Patch by Sangmoon Kim, 19 Aug 2005 * Fixes for drivers/cfi_flash.c: - Fix wrong timeout value usage in flash_status_check() - Round write_tout up when converting to msec in flash_get_size() - Remove clearing flash status at the end of flash_write_cfibuffer() which sets Intel 28F640J3 flash back to command mode on CSB472 Patch by Tolunay Orkun, 02 July 2005
2006-02-28 14:29:58 +00:00
/*
* Check if chip width is defined. If not, start detecting with 8bit.
*/
#ifndef CONFIG_SYS_FLASH_CFI_WIDTH
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
Major CFI-FLASH driver update: * Add env-variable "unlock" to handle initial state of sectors (locked/unlocked). Only the U-Boot image and it's environment is protected, all other sectors are unprotected (unlocked) if flash hardware protection is used (CFG_FLASH_PROTECTION) and the environment variable "unlock" is set to "yes". Patch by Stefan Roese, 28 Feb 2006 * Update drivers/cfi_flash.c: - find_sector() called in both versions of flash_write_cfiword() Patch by Peter Pearse, 27th Feb 2006 * CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode Patch by Jose Maria Lopez, 16 Jan 2006 * Add support for AMD/Spansion Flashes in flash_write_cfibuffer Patch by Alex Bastos and Thomas Schaefer, 2005-08-29 * Changes/fixes for drivers/cfi_flash.c: We *should* check if there are any error bits if the previous call returned ERR_OK (Otherwise we will have output an error message in flash_status_check() already.) The original code would only check for error bits if flash_status_check() returns ERR_TIMEOUT. Patch by Marcus Hall, 23 Aug 2005 * Changes/fixes for drivers/cfi_flash.c: - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c Patch by Sangmoon Kim, 19 Aug 2005 * Fixes for drivers/cfi_flash.c: - Fix wrong timeout value usage in flash_status_check() - Round write_tout up when converting to msec in flash_get_size() - Remove clearing flash status at the end of flash_write_cfibuffer() which sets Intel 28F640J3 flash back to command mode on CSB472 Patch by Tolunay Orkun, 02 July 2005
2006-02-28 14:29:58 +00:00
#endif
#ifdef CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
#define __maybe_weak __weak
#else
#define __maybe_weak static
#endif
/*
* 0xffff is an undefined value for the configuration register. When
* this value is returned, the configuration register shall not be
* written at all (default mode).
*/
static u16 cfi_flash_config_reg(int i)
{
#ifdef CONFIG_SYS_CFI_FLASH_CONFIG_REGS
return ((u16 [])CONFIG_SYS_CFI_FLASH_CONFIG_REGS)[i];
#else
return 0xffff;
#endif
}
#if defined(CONFIG_SYS_MAX_FLASH_BANKS_DETECT)
int cfi_flash_num_flash_banks = CONFIG_SYS_MAX_FLASH_BANKS_DETECT;
#endif
#ifdef CONFIG_CFI_FLASH /* for driver model */
static void cfi_flash_init_dm(void)
{
struct udevice *dev;
cfi_flash_num_flash_banks = 0;
/*
* The uclass_first_device() will probe the first device and
* uclass_next_device() will probe the rest if they exist. So
* that cfi_flash_probe() will get called assigning the base
* addresses that are available.
*/
for (uclass_first_device(UCLASS_MTD, &dev);
dev;
uclass_next_device(&dev)) {
}
}
static phys_addr_t cfi_flash_base[CFI_MAX_FLASH_BANKS];
phys_addr_t cfi_flash_bank_addr(int i)
{
return cfi_flash_base[i];
}
#else
__weak phys_addr_t cfi_flash_bank_addr(int i)
{
return ((phys_addr_t [])CONFIG_SYS_FLASH_BANKS_LIST)[i];
}
#endif
__weak unsigned long cfi_flash_bank_size(int i)
{
#ifdef CONFIG_SYS_FLASH_BANKS_SIZES
return ((unsigned long [])CONFIG_SYS_FLASH_BANKS_SIZES)[i];
#else
return 0;
#endif
}
__maybe_weak void flash_write8(u8 value, void *addr)
{
__raw_writeb(value, addr);
}
__maybe_weak void flash_write16(u16 value, void *addr)
{
__raw_writew(value, addr);
}
__maybe_weak void flash_write32(u32 value, void *addr)
{
__raw_writel(value, addr);
}
__maybe_weak void flash_write64(u64 value, void *addr)
{
/* No architectures currently implement __raw_writeq() */
*(volatile u64 *)addr = value;
}
__maybe_weak u8 flash_read8(void *addr)
{
return __raw_readb(addr);
}
__maybe_weak u16 flash_read16(void *addr)
{
return __raw_readw(addr);
}
__maybe_weak u32 flash_read32(void *addr)
{
return __raw_readl(addr);
}
__maybe_weak u64 flash_read64(void *addr)
{
/* No architectures currently implement __raw_readq() */
return *(volatile u64 *)addr;
}
/*-----------------------------------------------------------------------
*/
#if defined(CONFIG_ENV_IS_IN_FLASH) || defined(CONFIG_ENV_ADDR_REDUND) || (CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE)
flash_info_t *flash_get_info(ulong base)
{
int i;
flash_info_t *info;
for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) {
info = &flash_info[i];
if (info->size && info->start[0] <= base &&
base <= info->start[0] + info->size - 1)
return info;
}
return NULL;
}
#endif
unsigned long flash_sector_size(flash_info_t *info, flash_sect_t sect)
{
if (sect != (info->sector_count - 1))
return info->start[sect + 1] - info->start[sect];
else
return info->start[0] + info->size - info->start[sect];
}
/*-----------------------------------------------------------------------
* create an address based on the offset and the port width
*/
static inline void *
flash_map (flash_info_t * info, flash_sect_t sect, uint offset)
{
unsigned int byte_offset = offset * info->portwidth;
return (void *)(info->start[sect] + byte_offset);
}
static inline void flash_unmap(flash_info_t *info, flash_sect_t sect,
unsigned int offset, void *addr)
{
}
/*-----------------------------------------------------------------------
* make a proper sized command based on the port and chip widths
*/
static void flash_make_cmd(flash_info_t *info, u32 cmd, void *cmdbuf)
{
int i;
int cword_offset;
int cp_offset;
#if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA)
u32 cmd_le = cpu_to_le32(cmd);
#endif
uchar val;
uchar *cp = (uchar *) cmdbuf;
for (i = info->portwidth; i > 0; i--){
cword_offset = (info->portwidth-i)%info->chipwidth;
#if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA)
cp_offset = info->portwidth - i;
val = *((uchar*)&cmd_le + cword_offset);
#else
cp_offset = i - 1;
val = *((uchar*)&cmd + sizeof(u32) - cword_offset - 1);
#endif
cp[cp_offset] = (cword_offset >= sizeof(u32)) ? 0x00 : val;
}
}
#ifdef DEBUG
/*-----------------------------------------------------------------------
* Debug support
*/
static void print_longlong (char *str, unsigned long long data)
{
int i;
char *cp;
cp = (char *) &data;
for (i = 0; i < 8; i++)
sprintf (&str[i * 2], "%2.2x", *cp++);
}
static void flash_printqry (struct cfi_qry *qry)
{
u8 *p = (u8 *)qry;
int x, y;
for (x = 0; x < sizeof(struct cfi_qry); x += 16) {
debug("%02x : ", x);
for (y = 0; y < 16; y++)
debug("%2.2x ", p[x + y]);
debug(" ");
for (y = 0; y < 16; y++) {
unsigned char c = p[x + y];
if (c >= 0x20 && c <= 0x7e)
debug("%c", c);
else
debug(".");
}
debug("\n");
}
}
#endif
/*-----------------------------------------------------------------------
* read a character at a port width address
*/
static inline uchar flash_read_uchar (flash_info_t * info, uint offset)
{
uchar *cp;
uchar retval;
cp = flash_map (info, 0, offset);
#if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA)
retval = flash_read8(cp);
#else
retval = flash_read8(cp + info->portwidth - 1);
#endif
flash_unmap (info, 0, offset, cp);
return retval;
}
/*-----------------------------------------------------------------------
* read a word at a port width address, assume 16bit bus
*/
static inline ushort flash_read_word (flash_info_t * info, uint offset)
{
ushort *addr, retval;
addr = flash_map (info, 0, offset);
retval = flash_read16 (addr);
flash_unmap (info, 0, offset, addr);
return retval;
}
/*-----------------------------------------------------------------------
* read a long word by picking the least significant byte of each maximum
* port size word. Swap for ppc format.
*/
static ulong flash_read_long (flash_info_t * info, flash_sect_t sect,
uint offset)
{
uchar *addr;
ulong retval;
#ifdef DEBUG
int x;
#endif
addr = flash_map (info, sect, offset);
#ifdef DEBUG
debug ("long addr is at %p info->portwidth = %d\n", addr,
info->portwidth);
for (x = 0; x < 4 * info->portwidth; x++) {
debug ("addr[%x] = 0x%x\n", x, flash_read8(addr + x));
}
#endif
#if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA)
retval = ((flash_read8(addr) << 16) |
(flash_read8(addr + info->portwidth) << 24) |
(flash_read8(addr + 2 * info->portwidth)) |
(flash_read8(addr + 3 * info->portwidth) << 8));
#else
retval = ((flash_read8(addr + 2 * info->portwidth - 1) << 24) |
(flash_read8(addr + info->portwidth - 1) << 16) |
(flash_read8(addr + 4 * info->portwidth - 1) << 8) |
(flash_read8(addr + 3 * info->portwidth - 1)));
#endif
flash_unmap(info, sect, offset, addr);
return retval;
}
/*
* Write a proper sized command to the correct address
*/
void flash_write_cmd (flash_info_t * info, flash_sect_t sect,
uint offset, u32 cmd)
{
void *addr;
cfiword_t cword;
addr = flash_map (info, sect, offset);
flash_make_cmd (info, cmd, &cword);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
debug ("fwc addr %p cmd %x %x 8bit x %d bit\n", addr, cmd,
cword.w8, info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
flash_write8(cword.w8, addr);
break;
case FLASH_CFI_16BIT:
debug ("fwc addr %p cmd %x %4.4x 16bit x %d bit\n", addr,
cmd, cword.w16,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
flash_write16(cword.w16, addr);
break;
case FLASH_CFI_32BIT:
debug ("fwc addr %p cmd %x %8.8x 32bit x %d bit\n", addr,
cmd, cword.w32,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
flash_write32(cword.w32, addr);
break;
case FLASH_CFI_64BIT:
#ifdef DEBUG
{
char str[20];
print_longlong (str, cword.w64);
debug ("fwrite addr %p cmd %x %s 64 bit x %d bit\n",
addr, cmd, str,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
}
#endif
flash_write64(cword.w64, addr);
break;
}
/* Ensure all the instructions are fully finished */
sync();
flash_unmap(info, sect, offset, addr);
}
static void flash_unlock_seq (flash_info_t * info, flash_sect_t sect)
{
flash_write_cmd (info, sect, info->addr_unlock1, AMD_CMD_UNLOCK_START);
flash_write_cmd (info, sect, info->addr_unlock2, AMD_CMD_UNLOCK_ACK);
}
/*-----------------------------------------------------------------------
*/
static int flash_isequal (flash_info_t * info, flash_sect_t sect,
uint offset, uchar cmd)
{
void *addr;
cfiword_t cword;
int retval;
addr = flash_map (info, sect, offset);
flash_make_cmd (info, cmd, &cword);
debug ("is= cmd %x(%c) addr %p ", cmd, cmd, addr);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
debug ("is= %x %x\n", flash_read8(addr), cword.w8);
retval = (flash_read8(addr) == cword.w8);
break;
case FLASH_CFI_16BIT:
debug ("is= %4.4x %4.4x\n", flash_read16(addr), cword.w16);
retval = (flash_read16(addr) == cword.w16);
break;
case FLASH_CFI_32BIT:
debug ("is= %8.8x %8.8x\n", flash_read32(addr), cword.w32);
retval = (flash_read32(addr) == cword.w32);
break;
case FLASH_CFI_64BIT:
#ifdef DEBUG
{
char str1[20];
char str2[20];
print_longlong (str1, flash_read64(addr));
print_longlong (str2, cword.w64);
debug ("is= %s %s\n", str1, str2);
}
#endif
retval = (flash_read64(addr) == cword.w64);
break;
default:
retval = 0;
break;
}
flash_unmap(info, sect, offset, addr);
return retval;
}
Major CFI-FLASH driver update: * Add env-variable "unlock" to handle initial state of sectors (locked/unlocked). Only the U-Boot image and it's environment is protected, all other sectors are unprotected (unlocked) if flash hardware protection is used (CFG_FLASH_PROTECTION) and the environment variable "unlock" is set to "yes". Patch by Stefan Roese, 28 Feb 2006 * Update drivers/cfi_flash.c: - find_sector() called in both versions of flash_write_cfiword() Patch by Peter Pearse, 27th Feb 2006 * CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode Patch by Jose Maria Lopez, 16 Jan 2006 * Add support for AMD/Spansion Flashes in flash_write_cfibuffer Patch by Alex Bastos and Thomas Schaefer, 2005-08-29 * Changes/fixes for drivers/cfi_flash.c: We *should* check if there are any error bits if the previous call returned ERR_OK (Otherwise we will have output an error message in flash_status_check() already.) The original code would only check for error bits if flash_status_check() returns ERR_TIMEOUT. Patch by Marcus Hall, 23 Aug 2005 * Changes/fixes for drivers/cfi_flash.c: - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c Patch by Sangmoon Kim, 19 Aug 2005 * Fixes for drivers/cfi_flash.c: - Fix wrong timeout value usage in flash_status_check() - Round write_tout up when converting to msec in flash_get_size() - Remove clearing flash status at the end of flash_write_cfibuffer() which sets Intel 28F640J3 flash back to command mode on CSB472 Patch by Tolunay Orkun, 02 July 2005
2006-02-28 14:29:58 +00:00
/*-----------------------------------------------------------------------
*/
static int flash_isset (flash_info_t * info, flash_sect_t sect,
uint offset, uchar cmd)
{
void *addr;
cfiword_t cword;
int retval;
addr = flash_map (info, sect, offset);
flash_make_cmd (info, cmd, &cword);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
retval = ((flash_read8(addr) & cword.w8) == cword.w8);
break;
case FLASH_CFI_16BIT:
retval = ((flash_read16(addr) & cword.w16) == cword.w16);
break;
case FLASH_CFI_32BIT:
retval = ((flash_read32(addr) & cword.w32) == cword.w32);
break;
case FLASH_CFI_64BIT:
retval = ((flash_read64(addr) & cword.w64) == cword.w64);
break;
default:
retval = 0;
break;
}
flash_unmap(info, sect, offset, addr);
return retval;
}
/*-----------------------------------------------------------------------
*/
static int flash_toggle (flash_info_t * info, flash_sect_t sect,
uint offset, uchar cmd)
{
void *addr;
cfiword_t cword;
int retval;
addr = flash_map (info, sect, offset);
flash_make_cmd (info, cmd, &cword);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
retval = flash_read8(addr) != flash_read8(addr);
break;
case FLASH_CFI_16BIT:
retval = flash_read16(addr) != flash_read16(addr);
break;
case FLASH_CFI_32BIT:
retval = flash_read32(addr) != flash_read32(addr);
break;
case FLASH_CFI_64BIT:
CFI Driver: Fix "flash not ready" problem This patch fixes a problem on systems where the NOR flash is attached to a 64 bit bus. The toggle bit detection in flash_toggle() is based on the assumption that the same flash address is read twice without any other interjacent flash accesses. However, on 32 bit systems the function flash_read64() [as currently implemented] does not perform an atomic 64 bit read - instead, this is broken down into two 32 bit read accesses on addresses "addr" and "addr + 4". So instead of reading a 64 bit value twice from "addr", we see a sequence of 4 32 bit reads from "addr", "addr + 4", "addr", and "addr + 4". The consequence is that flash_toggle() fails to work. This patch implements a simple, but somewhat ugly solution, as it avoids the use of flash_read64() in this critical place (by breaking it down manually into 32 bit read operations) instead of rewriting flash_read64() such to perform atomic 64 bit reads as one could expect. However, such a rewrite would require the use of floating point load operations, which becomes pretty complex: save MSR; set Floating Point Enable bit in MSR; use "lfd" instruction to perform atomic 64 bit read; use "stfd" to store value to temporary variable on stack; load u64 value from temporary variable; restore saved MSR; return u64 value; The benefit-cost ratio of such an implementation was considered too bad to actually attempt this, especially as we can expect that such an implementation would not only have a bigger memory footprint but also cause a performance degradation. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31 00:12:28 +00:00
retval = ( (flash_read32( addr ) != flash_read32( addr )) ||
(flash_read32(addr+4) != flash_read32(addr+4)) );
break;
default:
retval = 0;
break;
}
flash_unmap(info, sect, offset, addr);
return retval;
}
/*
* flash_is_busy - check to see if the flash is busy
*
* This routine checks the status of the chip and returns true if the
* chip is busy.
*/
static int flash_is_busy (flash_info_t * info, flash_sect_t sect)
{
int retval;
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
retval = !flash_isset (info, sect, 0, FLASH_STATUS_DONE);
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
#endif
retval = flash_toggle (info, sect, 0, AMD_STATUS_TOGGLE);
break;
default:
retval = 0;
}
debug ("flash_is_busy: %d\n", retval);
return retval;
}
/*-----------------------------------------------------------------------
* wait for XSR.7 to be set. Time out with an error if it does not.
* This routine does not set the flash to read-array mode.
*/
static int flash_status_check (flash_info_t * info, flash_sect_t sector,
ulong tout, char *prompt)
{
ulong start;
#if CONFIG_SYS_HZ != 1000
if ((ulong)CONFIG_SYS_HZ > 100000)
tout *= (ulong)CONFIG_SYS_HZ / 1000; /* for a big HZ, avoid overflow */
else
tout = DIV_ROUND_UP(tout * (ulong)CONFIG_SYS_HZ, 1000);
#endif
/* Wait for command completion */
#ifdef CONFIG_SYS_LOW_RES_TIMER
reset_timer();
#endif
start = get_timer (0);
WATCHDOG_RESET();
while (flash_is_busy (info, sector)) {
if (get_timer (start) > tout) {
printf ("Flash %s timeout at address %lx data %lx\n",
prompt, info->start[sector],
flash_read_long (info, sector, 0));
flash_write_cmd (info, sector, 0, info->cmd_reset);
udelay(1);
return ERR_TIMOUT;
}
udelay (1); /* also triggers watchdog */
}
return ERR_OK;
}
/*-----------------------------------------------------------------------
* Wait for XSR.7 to be set, if it times out print an error, otherwise
* do a full status check.
*
* This routine sets the flash to read-array mode.
*/
static int flash_full_status_check (flash_info_t * info, flash_sect_t sector,
ulong tout, char *prompt)
{
int retcode;
retcode = flash_status_check (info, sector, tout, prompt);
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_EXTENDED:
case CFI_CMDSET_INTEL_STANDARD:
if ((retcode == ERR_OK)
&& !flash_isset(info, sector, 0, FLASH_STATUS_DONE)) {
retcode = ERR_INVAL;
printf ("Flash %s error at address %lx\n", prompt,
info->start[sector]);
if (flash_isset (info, sector, 0, FLASH_STATUS_ECLBS |
FLASH_STATUS_PSLBS)) {
puts ("Command Sequence Error.\n");
} else if (flash_isset (info, sector, 0,
FLASH_STATUS_ECLBS)) {
puts ("Block Erase Error.\n");
retcode = ERR_NOT_ERASED;
} else if (flash_isset (info, sector, 0,
FLASH_STATUS_PSLBS)) {
puts ("Locking Error\n");
}
if (flash_isset (info, sector, 0, FLASH_STATUS_DPS)) {
puts ("Block locked.\n");
retcode = ERR_PROTECTED;
}
if (flash_isset (info, sector, 0, FLASH_STATUS_VPENS))
puts ("Vpp Low Error.\n");
}
flash_write_cmd (info, sector, 0, info->cmd_reset);
udelay(1);
break;
default:
break;
}
return retcode;
}
static int use_flash_status_poll(flash_info_t *info)
{
#ifdef CONFIG_SYS_CFI_FLASH_STATUS_POLL
if (info->vendor == CFI_CMDSET_AMD_EXTENDED ||
info->vendor == CFI_CMDSET_AMD_STANDARD)
return 1;
#endif
return 0;
}
static int flash_status_poll(flash_info_t *info, void *src, void *dst,
ulong tout, char *prompt)
{
#ifdef CONFIG_SYS_CFI_FLASH_STATUS_POLL
ulong start;
int ready;
#if CONFIG_SYS_HZ != 1000
if ((ulong)CONFIG_SYS_HZ > 100000)
tout *= (ulong)CONFIG_SYS_HZ / 1000; /* for a big HZ, avoid overflow */
else
tout = DIV_ROUND_UP(tout * (ulong)CONFIG_SYS_HZ, 1000);
#endif
/* Wait for command completion */
#ifdef CONFIG_SYS_LOW_RES_TIMER
reset_timer();
#endif
start = get_timer(0);
WATCHDOG_RESET();
while (1) {
switch (info->portwidth) {
case FLASH_CFI_8BIT:
ready = flash_read8(dst) == flash_read8(src);
break;
case FLASH_CFI_16BIT:
ready = flash_read16(dst) == flash_read16(src);
break;
case FLASH_CFI_32BIT:
ready = flash_read32(dst) == flash_read32(src);
break;
case FLASH_CFI_64BIT:
ready = flash_read64(dst) == flash_read64(src);
break;
default:
ready = 0;
break;
}
if (ready)
break;
if (get_timer(start) > tout) {
printf("Flash %s timeout at address %lx data %lx\n",
prompt, (ulong)dst, (ulong)flash_read8(dst));
return ERR_TIMOUT;
}
udelay(1); /* also triggers watchdog */
}
#endif /* CONFIG_SYS_CFI_FLASH_STATUS_POLL */
return ERR_OK;
}
/*-----------------------------------------------------------------------
*/
static void flash_add_byte (flash_info_t * info, cfiword_t * cword, uchar c)
{
#if defined(__LITTLE_ENDIAN) && !defined(CONFIG_SYS_WRITE_SWAPPED_DATA)
unsigned short w;
unsigned int l;
unsigned long long ll;
#endif
switch (info->portwidth) {
case FLASH_CFI_8BIT:
cword->w8 = c;
break;
case FLASH_CFI_16BIT:
#if defined(__LITTLE_ENDIAN) && !defined(CONFIG_SYS_WRITE_SWAPPED_DATA)
w = c;
w <<= 8;
cword->w16 = (cword->w16 >> 8) | w;
#else
cword->w16 = (cword->w16 << 8) | c;
#endif
break;
case FLASH_CFI_32BIT:
#if defined(__LITTLE_ENDIAN) && !defined(CONFIG_SYS_WRITE_SWAPPED_DATA)
l = c;
l <<= 24;
cword->w32 = (cword->w32 >> 8) | l;
#else
cword->w32 = (cword->w32 << 8) | c;
#endif
break;
case FLASH_CFI_64BIT:
#if defined(__LITTLE_ENDIAN) && !defined(CONFIG_SYS_WRITE_SWAPPED_DATA)
ll = c;
ll <<= 56;
cword->w64 = (cword->w64 >> 8) | ll;
#else
cword->w64 = (cword->w64 << 8) | c;
#endif
break;
}
}
/*
* Loop through the sector table starting from the previously found sector.
* Searches forwards or backwards, dependent on the passed address.
*/
static flash_sect_t find_sector (flash_info_t * info, ulong addr)
{
static flash_sect_t saved_sector; /* previously found sector */
static flash_info_t *saved_info; /* previously used flash bank */
flash_sect_t sector = saved_sector;
if ((info != saved_info) || (sector >= info->sector_count))
sector = 0;
while ((info->start[sector] < addr)
&& (sector < info->sector_count - 1))
sector++;
while ((info->start[sector] > addr) && (sector > 0))
/*
* also decrements the sector in case of an overshot
* in the first loop
*/
sector--;
saved_sector = sector;
saved_info = info;
return sector;
}
/*-----------------------------------------------------------------------
*/
static int flash_write_cfiword (flash_info_t * info, ulong dest,
cfiword_t cword)
{
void *dstaddr = (void *)dest;
int flag;
flash_sect_t sect = 0;
char sect_found = 0;
/* Check if Flash is (sufficiently) erased */
switch (info->portwidth) {
case FLASH_CFI_8BIT:
flag = ((flash_read8(dstaddr) & cword.w8) == cword.w8);
break;
case FLASH_CFI_16BIT:
flag = ((flash_read16(dstaddr) & cword.w16) == cword.w16);
break;
case FLASH_CFI_32BIT:
flag = ((flash_read32(dstaddr) & cword.w32) == cword.w32);
break;
case FLASH_CFI_64BIT:
flag = ((flash_read64(dstaddr) & cword.w64) == cword.w64);
break;
default:
flag = 0;
break;
}
if (!flag)
return ERR_NOT_ERASED;
/* Disable interrupts which might cause a timeout here */
flag = disable_interrupts ();
Major CFI-FLASH driver update: * Add env-variable "unlock" to handle initial state of sectors (locked/unlocked). Only the U-Boot image and it's environment is protected, all other sectors are unprotected (unlocked) if flash hardware protection is used (CFG_FLASH_PROTECTION) and the environment variable "unlock" is set to "yes". Patch by Stefan Roese, 28 Feb 2006 * Update drivers/cfi_flash.c: - find_sector() called in both versions of flash_write_cfiword() Patch by Peter Pearse, 27th Feb 2006 * CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode Patch by Jose Maria Lopez, 16 Jan 2006 * Add support for AMD/Spansion Flashes in flash_write_cfibuffer Patch by Alex Bastos and Thomas Schaefer, 2005-08-29 * Changes/fixes for drivers/cfi_flash.c: We *should* check if there are any error bits if the previous call returned ERR_OK (Otherwise we will have output an error message in flash_status_check() already.) The original code would only check for error bits if flash_status_check() returns ERR_TIMEOUT. Patch by Marcus Hall, 23 Aug 2005 * Changes/fixes for drivers/cfi_flash.c: - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c Patch by Sangmoon Kim, 19 Aug 2005 * Fixes for drivers/cfi_flash.c: - Fix wrong timeout value usage in flash_status_check() - Round write_tout up when converting to msec in flash_get_size() - Remove clearing flash status at the end of flash_write_cfibuffer() which sets Intel 28F640J3 flash back to command mode on CSB472 Patch by Tolunay Orkun, 02 July 2005
2006-02-28 14:29:58 +00:00
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_EXTENDED:
case CFI_CMDSET_INTEL_STANDARD:
flash_write_cmd (info, 0, 0, FLASH_CMD_CLEAR_STATUS);
flash_write_cmd (info, 0, 0, FLASH_CMD_WRITE);
break;
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
sect = find_sector(info, dest);
flash_unlock_seq (info, sect);
flash_write_cmd (info, sect, info->addr_unlock1, AMD_CMD_WRITE);
sect_found = 1;
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
sect = find_sector(info, dest);
flash_unlock_seq (info, 0);
flash_write_cmd (info, 0, info->addr_unlock1, AMD_CMD_WRITE);
sect_found = 1;
break;
#endif
}
switch (info->portwidth) {
case FLASH_CFI_8BIT:
flash_write8(cword.w8, dstaddr);
break;
case FLASH_CFI_16BIT:
flash_write16(cword.w16, dstaddr);
break;
case FLASH_CFI_32BIT:
flash_write32(cword.w32, dstaddr);
break;
case FLASH_CFI_64BIT:
flash_write64(cword.w64, dstaddr);
break;
}
/* re-enable interrupts if necessary */
if (flag)
enable_interrupts ();
if (!sect_found)
sect = find_sector (info, dest);
if (use_flash_status_poll(info))
return flash_status_poll(info, &cword, dstaddr,
info->write_tout, "write");
else
return flash_full_status_check(info, sect,
info->write_tout, "write");
}
#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
static int flash_write_cfibuffer (flash_info_t * info, ulong dest, uchar * cp,
int len)
{
flash_sect_t sector;
int cnt;
int retcode;
void *src = cp;
void *dst = (void *)dest;
void *dst2 = dst;
int flag = 1;
uint offset = 0;
unsigned int shift;
uchar write_cmd;
switch (info->portwidth) {
case FLASH_CFI_8BIT:
shift = 0;
break;
case FLASH_CFI_16BIT:
shift = 1;
break;
case FLASH_CFI_32BIT:
shift = 2;
break;
case FLASH_CFI_64BIT:
shift = 3;
break;
default:
retcode = ERR_INVAL;
goto out_unmap;
}
cnt = len >> shift;
while ((cnt-- > 0) && (flag == 1)) {
switch (info->portwidth) {
case FLASH_CFI_8BIT:
flag = ((flash_read8(dst2) & flash_read8(src)) ==
flash_read8(src));
src += 1, dst2 += 1;
break;
case FLASH_CFI_16BIT:
flag = ((flash_read16(dst2) & flash_read16(src)) ==
flash_read16(src));
src += 2, dst2 += 2;
break;
case FLASH_CFI_32BIT:
flag = ((flash_read32(dst2) & flash_read32(src)) ==
flash_read32(src));
src += 4, dst2 += 4;
break;
case FLASH_CFI_64BIT:
flag = ((flash_read64(dst2) & flash_read64(src)) ==
flash_read64(src));
src += 8, dst2 += 8;
break;
}
}
if (!flag) {
retcode = ERR_NOT_ERASED;
goto out_unmap;
}
src = cp;
sector = find_sector (info, dest);
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
write_cmd = (info->vendor == CFI_CMDSET_INTEL_PROG_REGIONS) ?
FLASH_CMD_WRITE_BUFFER_PROG : FLASH_CMD_WRITE_TO_BUFFER;
flash_write_cmd (info, sector, 0, FLASH_CMD_CLEAR_STATUS);
flash_write_cmd (info, sector, 0, FLASH_CMD_READ_STATUS);
flash_write_cmd (info, sector, 0, write_cmd);
retcode = flash_status_check (info, sector,
info->buffer_write_tout,
"write to buffer");
if (retcode == ERR_OK) {
/* reduce the number of loops by the width of
* the port */
cnt = len >> shift;
flash_write_cmd (info, sector, 0, cnt - 1);
while (cnt-- > 0) {
switch (info->portwidth) {
case FLASH_CFI_8BIT:
flash_write8(flash_read8(src), dst);
src += 1, dst += 1;
break;
case FLASH_CFI_16BIT:
flash_write16(flash_read16(src), dst);
src += 2, dst += 2;
break;
case FLASH_CFI_32BIT:
flash_write32(flash_read32(src), dst);
src += 4, dst += 4;
break;
case FLASH_CFI_64BIT:
flash_write64(flash_read64(src), dst);
src += 8, dst += 8;
break;
default:
retcode = ERR_INVAL;
goto out_unmap;
}
}
flash_write_cmd (info, sector, 0,
FLASH_CMD_WRITE_BUFFER_CONFIRM);
retcode = flash_full_status_check (
info, sector, info->buffer_write_tout,
"buffer write");
}
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
flash_unlock_seq(info, sector);
#ifdef CONFIG_FLASH_SPANSION_S29WS_N
offset = ((unsigned long)dst - info->start[sector]) >> shift;
#endif
flash_write_cmd(info, sector, offset, AMD_CMD_WRITE_TO_BUFFER);
cnt = len >> shift;
flash_write_cmd(info, sector, offset, cnt - 1);
switch (info->portwidth) {
case FLASH_CFI_8BIT:
while (cnt-- > 0) {
flash_write8(flash_read8(src), dst);
src += 1, dst += 1;
}
break;
case FLASH_CFI_16BIT:
while (cnt-- > 0) {
flash_write16(flash_read16(src), dst);
src += 2, dst += 2;
}
break;
case FLASH_CFI_32BIT:
while (cnt-- > 0) {
flash_write32(flash_read32(src), dst);
src += 4, dst += 4;
}
break;
case FLASH_CFI_64BIT:
while (cnt-- > 0) {
flash_write64(flash_read64(src), dst);
src += 8, dst += 8;
}
break;
default:
retcode = ERR_INVAL;
goto out_unmap;
}
flash_write_cmd (info, sector, 0, AMD_CMD_WRITE_BUFFER_CONFIRM);
if (use_flash_status_poll(info))
retcode = flash_status_poll(info, src - (1 << shift),
dst - (1 << shift),
info->buffer_write_tout,
"buffer write");
else
retcode = flash_full_status_check(info, sector,
info->buffer_write_tout,
"buffer write");
break;
default:
debug ("Unknown Command Set\n");
retcode = ERR_INVAL;
break;
}
out_unmap:
return retcode;
}
#endif /* CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
/*-----------------------------------------------------------------------
*/
int flash_erase (flash_info_t * info, int s_first, int s_last)
{
int rcode = 0;
int prot;
flash_sect_t sect;
int st;
if (info->flash_id != FLASH_MAN_CFI) {
puts ("Can't erase unknown flash type - aborted\n");
return 1;
}
if ((s_first < 0) || (s_first > s_last)) {
puts ("- no sectors to erase\n");
return 1;
}
prot = 0;
for (sect = s_first; sect <= s_last; ++sect) {
if (info->protect[sect]) {
prot++;
}
}
if (prot) {
printf ("- Warning: %d protected sectors will not be erased!\n",
prot);
} else if (flash_verbose) {
putc ('\n');
}
for (sect = s_first; sect <= s_last; sect++) {
if (ctrlc()) {
printf("\n");
return 1;
}
if (info->protect[sect] == 0) { /* not protected */
#ifdef CONFIG_SYS_FLASH_CHECK_BLANK_BEFORE_ERASE
int k;
int size;
int erased;
u32 *flash;
/*
* Check if whole sector is erased
*/
size = flash_sector_size(info, sect);
erased = 1;
flash = (u32 *)info->start[sect];
/* divide by 4 for longword access */
size = size >> 2;
for (k = 0; k < size; k++) {
if (flash_read32(flash++) != 0xffffffff) {
erased = 0;
break;
}
}
if (erased) {
if (flash_verbose)
putc(',');
continue;
}
#endif
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
flash_write_cmd (info, sect, 0,
FLASH_CMD_CLEAR_STATUS);
flash_write_cmd (info, sect, 0,
FLASH_CMD_BLOCK_ERASE);
flash_write_cmd (info, sect, 0,
FLASH_CMD_ERASE_CONFIRM);
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
flash_unlock_seq (info, sect);
flash_write_cmd (info, sect,
info->addr_unlock1,
AMD_CMD_ERASE_START);
flash_unlock_seq (info, sect);
flash_write_cmd (info, sect, 0,
info->cmd_erase_sector);
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
flash_unlock_seq (info, 0);
flash_write_cmd (info, 0, info->addr_unlock1,
AMD_CMD_ERASE_START);
flash_unlock_seq (info, 0);
flash_write_cmd (info, sect, 0,
AMD_CMD_ERASE_SECTOR);
break;
#endif
default:
debug ("Unkown flash vendor %d\n",
info->vendor);
break;
}
if (use_flash_status_poll(info)) {
cfiword_t cword;
void *dest;
cword.w64 = 0xffffffffffffffffULL;
dest = flash_map(info, sect, 0);
st = flash_status_poll(info, &cword, dest,
info->erase_blk_tout, "erase");
flash_unmap(info, sect, 0, dest);
} else
st = flash_full_status_check(info, sect,
info->erase_blk_tout,
"erase");
if (st)
rcode = 1;
else if (flash_verbose)
putc ('.');
}
}
if (flash_verbose)
puts (" done\n");
return rcode;
}
#ifdef CONFIG_SYS_FLASH_EMPTY_INFO
static int sector_erased(flash_info_t *info, int i)
{
int k;
int size;
u32 *flash;
/*
* Check if whole sector is erased
*/
size = flash_sector_size(info, i);
flash = (u32 *)info->start[i];
/* divide by 4 for longword access */
size = size >> 2;
for (k = 0; k < size; k++) {
if (flash_read32(flash++) != 0xffffffff)
return 0; /* not erased */
}
return 1; /* erased */
}
#endif /* CONFIG_SYS_FLASH_EMPTY_INFO */
void flash_print_info (flash_info_t * info)
{
int i;
if (info->flash_id != FLASH_MAN_CFI) {
puts ("missing or unknown FLASH type\n");
return;
}
printf ("%s flash (%d x %d)",
info->name,
(info->portwidth << 3), (info->chipwidth << 3));
if (info->size < 1024*1024)
printf (" Size: %ld kB in %d Sectors\n",
info->size >> 10, info->sector_count);
else
printf (" Size: %ld MB in %d Sectors\n",
info->size >> 20, info->sector_count);
printf (" ");
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
printf ("Intel Prog Regions");
break;
case CFI_CMDSET_INTEL_STANDARD:
printf ("Intel Standard");
break;
case CFI_CMDSET_INTEL_EXTENDED:
printf ("Intel Extended");
break;
case CFI_CMDSET_AMD_STANDARD:
printf ("AMD Standard");
break;
case CFI_CMDSET_AMD_EXTENDED:
printf ("AMD Extended");
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
printf ("AMD Legacy");
break;
#endif
default:
printf ("Unknown (%d)", info->vendor);
break;
}
printf (" command set, Manufacturer ID: 0x%02X, Device ID: 0x",
info->manufacturer_id);
printf (info->chipwidth == FLASH_CFI_16BIT ? "%04X" : "%02X",
info->device_id);
if ((info->device_id & 0xff) == 0x7E) {
printf(info->chipwidth == FLASH_CFI_16BIT ? "%04X" : "%02X",
info->device_id2);
}
if ((info->vendor == CFI_CMDSET_AMD_STANDARD) && (info->legacy_unlock))
printf("\n Advanced Sector Protection (PPB) enabled");
printf ("\n Erase timeout: %ld ms, write timeout: %ld ms\n",
info->erase_blk_tout,
info->write_tout);
if (info->buffer_size > 1) {
printf (" Buffer write timeout: %ld ms, "
"buffer size: %d bytes\n",
info->buffer_write_tout,
info->buffer_size);
}
puts ("\n Sector Start Addresses:");
for (i = 0; i < info->sector_count; ++i) {
if (ctrlc())
break;
if ((i % 5) == 0)
putc('\n');
#ifdef CONFIG_SYS_FLASH_EMPTY_INFO
/* print empty and read-only info */
printf (" %08lX %c %s ",
info->start[i],
sector_erased(info, i) ? 'E' : ' ',
info->protect[i] ? "RO" : " ");
#else /* ! CONFIG_SYS_FLASH_EMPTY_INFO */
printf (" %08lX %s ",
info->start[i],
info->protect[i] ? "RO" : " ");
#endif
}
putc ('\n');
return;
}
/*-----------------------------------------------------------------------
* This is used in a few places in write_buf() to show programming
* progress. Making it a function is nasty because it needs to do side
* effect updates to digit and dots. Repeated code is nasty too, so
* we define it once here.
*/
#ifdef CONFIG_FLASH_SHOW_PROGRESS
#define FLASH_SHOW_PROGRESS(scale, dots, digit, dots_sub) \
if (flash_verbose) { \
dots -= dots_sub; \
if ((scale > 0) && (dots <= 0)) { \
if ((digit % 5) == 0) \
printf ("%d", digit / 5); \
else \
putc ('.'); \
digit--; \
dots += scale; \
} \
}
#else
#define FLASH_SHOW_PROGRESS(scale, dots, digit, dots_sub)
#endif
/*-----------------------------------------------------------------------
* Copy memory to flash, returns:
* 0 - OK
* 1 - write timeout
* 2 - Flash not erased
*/
int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
{
ulong wp;
uchar *p;
int aln;
cfiword_t cword;
int i, rc;
#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
int buffered_size;
#endif
#ifdef CONFIG_FLASH_SHOW_PROGRESS
int digit = CONFIG_FLASH_SHOW_PROGRESS;
int scale = 0;
int dots = 0;
/*
* Suppress if there are fewer than CONFIG_FLASH_SHOW_PROGRESS writes.
*/
if (cnt >= CONFIG_FLASH_SHOW_PROGRESS) {
scale = (int)((cnt + CONFIG_FLASH_SHOW_PROGRESS - 1) /
CONFIG_FLASH_SHOW_PROGRESS);
}
#endif
/* get lower aligned address */
wp = (addr & ~(info->portwidth - 1));
/* handle unaligned start */
if ((aln = addr - wp) != 0) {
cword.w32 = 0;
p = (uchar *)wp;
for (i = 0; i < aln; ++i)
flash_add_byte (info, &cword, flash_read8(p + i));
for (; (i < info->portwidth) && (cnt > 0); i++) {
flash_add_byte (info, &cword, *src++);
cnt--;
}
for (; (cnt == 0) && (i < info->portwidth); ++i)
flash_add_byte (info, &cword, flash_read8(p + i));
rc = flash_write_cfiword (info, wp, cword);
if (rc != 0)
return rc;
wp += i;
FLASH_SHOW_PROGRESS(scale, dots, digit, i);
}
/* handle the aligned part */
#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
buffered_size = (info->portwidth / info->chipwidth);
buffered_size *= info->buffer_size;
while (cnt >= info->portwidth) {
/* prohibit buffer write when buffer_size is 1 */
if (info->buffer_size == 1) {
cword.w32 = 0;
for (i = 0; i < info->portwidth; i++)
flash_add_byte (info, &cword, *src++);
if ((rc = flash_write_cfiword (info, wp, cword)) != 0)
return rc;
wp += info->portwidth;
cnt -= info->portwidth;
continue;
}
/* write buffer until next buffered_size aligned boundary */
i = buffered_size - (wp % buffered_size);
if (i > cnt)
i = cnt;
if ((rc = flash_write_cfibuffer (info, wp, src, i)) != ERR_OK)
return rc;
i -= i & (info->portwidth - 1);
wp += i;
src += i;
cnt -= i;
FLASH_SHOW_PROGRESS(scale, dots, digit, i);
/* Only check every once in a while */
if ((cnt & 0xFFFF) < buffered_size && ctrlc())
return ERR_ABORTED;
}
#else
while (cnt >= info->portwidth) {
cword.w32 = 0;
for (i = 0; i < info->portwidth; i++) {
flash_add_byte (info, &cword, *src++);
}
if ((rc = flash_write_cfiword (info, wp, cword)) != 0)
return rc;
wp += info->portwidth;
cnt -= info->portwidth;
FLASH_SHOW_PROGRESS(scale, dots, digit, info->portwidth);
/* Only check every once in a while */
if ((cnt & 0xFFFF) < info->portwidth && ctrlc())
return ERR_ABORTED;
}
#endif /* CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
if (cnt == 0) {
return (0);
}
/*
* handle unaligned tail bytes
*/
cword.w32 = 0;
p = (uchar *)wp;
for (i = 0; (i < info->portwidth) && (cnt > 0); ++i) {
flash_add_byte (info, &cword, *src++);
--cnt;
}
for (; i < info->portwidth; ++i)
flash_add_byte (info, &cword, flash_read8(p + i));
return flash_write_cfiword (info, wp, cword);
}
static inline int manufact_match(flash_info_t *info, u32 manu)
{
return info->manufacturer_id == ((manu & FLASH_VENDMASK) >> 16);
}
/*-----------------------------------------------------------------------
*/
#ifdef CONFIG_SYS_FLASH_PROTECTION
static int cfi_protect_bugfix(flash_info_t *info, long sector, int prot)
{
if (manufact_match(info, INTEL_MANUFACT)
&& info->device_id == NUMONYX_256MBIT) {
/*
* see errata called
* "Numonyx Axcell P33/P30 Specification Update" :)
*/
flash_write_cmd(info, sector, 0, FLASH_CMD_READ_ID);
if (!flash_isequal(info, sector, FLASH_OFFSET_PROTECT,
prot)) {
/*
* cmd must come before FLASH_CMD_PROTECT + 20us
* Disable interrupts which might cause a timeout here.
*/
int flag = disable_interrupts();
unsigned short cmd;
if (prot)
cmd = FLASH_CMD_PROTECT_SET;
else
cmd = FLASH_CMD_PROTECT_CLEAR;
flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT);
flash_write_cmd(info, sector, 0, cmd);
/* re-enable interrupts if necessary */
if (flag)
enable_interrupts();
}
return 1;
}
return 0;
}
int flash_real_protect (flash_info_t * info, long sector, int prot)
{
int retcode = 0;
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
if (!cfi_protect_bugfix(info, sector, prot)) {
flash_write_cmd(info, sector, 0,
FLASH_CMD_CLEAR_STATUS);
flash_write_cmd(info, sector, 0,
FLASH_CMD_PROTECT);
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips. I have "ported" U-boot to a in house made board with Numonyx Axcell P33/P30 256-Mbit 65nm flash chips. After some time :( searching for bugs in our board or soft, we have discovered that those chips have a small but annoying bug, documented in "Numonyx Axcell P33/P30 256-Mbit Specification Update" It states : When customer uses [...] block unlock, the block lock status might be altered inadvertently. Lock status might be set to either 01h or 03h unexpectedly (00h as expected data), which leads to program/erase failure on certain blocks. A working workaround is given, which I have applied and tested with success : Workaround: If the interval between 60h and its subsequent command can be guaranteed within 20us, Option I is recommended, otherwise Option II (involves hardware) should be selected. Option I: The table below lists the detail command sequences: Command Data bus Address bus Remarks Sequence 1 90h Block Address Read Lock Status 2 Read Block Address + 02h (2)(3) (1) 3 60h Block Address (2)(3) (1) Lock/Unlock/RCR Configuration 4 D0h/01h/03h Block Address Notes: (1) Block Address refers to RCR configuration data only when the 60h command sequence is used to set RCR register combined with 03h subsequent command. (2) For the third and fourth command sequences, the Block Address must be the same. (3) The interval between 60h command and its subsequent D0h/01h/2Fh/03h commands should be less than 20us. And here is a log comparison of a simple (destructive) flash test without and with the workaround. diff without-numonyx-workaround.log with-numonyx-workaround.log -U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:07:47) +U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:25:19) CPU: Freescale MCF5484 CPU CLK 200 MHz BUS CLK 100 MHz Board: Macq Electronique ME2060 I2C: ready DRAM: 64 MiB FLASH: 32 MiB In: serial Out: serial Err: serial Net: FEC0, FEC1 -> flinfo Bank # 1: CFI conformant FLASH (16 x 16) Size: 32 MB in 259 Sectors Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8922 Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 5 ms, buffer size: 1024 bytes Sector Start Addresses: FE000000 RO FE008000 RO FE010000 RO FE018000 RO FE020000 RO FE040000 RO FE060000 RO FE080000 RO FE0A0000 RO FE0C0000 RO ... FFF80000 RO FFFA0000 RO FFFC0000 RO FFFE0000 RO -> protect off all Un-Protect Flash Bank # 1 ................... done -> erase all Erase Flash Bank # 1 ................... done -> cp.b 1000000 fe000000 2000000 -Copy to Flash... Flash not Erased +Copy to Flash... done -> Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-17 16:40:25 +00:00
if (prot)
flash_write_cmd(info, sector, 0,
FLASH_CMD_PROTECT_SET);
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips. I have "ported" U-boot to a in house made board with Numonyx Axcell P33/P30 256-Mbit 65nm flash chips. After some time :( searching for bugs in our board or soft, we have discovered that those chips have a small but annoying bug, documented in "Numonyx Axcell P33/P30 256-Mbit Specification Update" It states : When customer uses [...] block unlock, the block lock status might be altered inadvertently. Lock status might be set to either 01h or 03h unexpectedly (00h as expected data), which leads to program/erase failure on certain blocks. A working workaround is given, which I have applied and tested with success : Workaround: If the interval between 60h and its subsequent command can be guaranteed within 20us, Option I is recommended, otherwise Option II (involves hardware) should be selected. Option I: The table below lists the detail command sequences: Command Data bus Address bus Remarks Sequence 1 90h Block Address Read Lock Status 2 Read Block Address + 02h (2)(3) (1) 3 60h Block Address (2)(3) (1) Lock/Unlock/RCR Configuration 4 D0h/01h/03h Block Address Notes: (1) Block Address refers to RCR configuration data only when the 60h command sequence is used to set RCR register combined with 03h subsequent command. (2) For the third and fourth command sequences, the Block Address must be the same. (3) The interval between 60h command and its subsequent D0h/01h/2Fh/03h commands should be less than 20us. And here is a log comparison of a simple (destructive) flash test without and with the workaround. diff without-numonyx-workaround.log with-numonyx-workaround.log -U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:07:47) +U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:25:19) CPU: Freescale MCF5484 CPU CLK 200 MHz BUS CLK 100 MHz Board: Macq Electronique ME2060 I2C: ready DRAM: 64 MiB FLASH: 32 MiB In: serial Out: serial Err: serial Net: FEC0, FEC1 -> flinfo Bank # 1: CFI conformant FLASH (16 x 16) Size: 32 MB in 259 Sectors Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8922 Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 5 ms, buffer size: 1024 bytes Sector Start Addresses: FE000000 RO FE008000 RO FE010000 RO FE018000 RO FE020000 RO FE040000 RO FE060000 RO FE080000 RO FE0A0000 RO FE0C0000 RO ... FFF80000 RO FFFA0000 RO FFFC0000 RO FFFE0000 RO -> protect off all Un-Protect Flash Bank # 1 ................... done -> erase all Erase Flash Bank # 1 ................... done -> cp.b 1000000 fe000000 2000000 -Copy to Flash... Flash not Erased +Copy to Flash... done -> Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-17 16:40:25 +00:00
else
flash_write_cmd(info, sector, 0,
FLASH_CMD_PROTECT_CLEAR);
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips. I have "ported" U-boot to a in house made board with Numonyx Axcell P33/P30 256-Mbit 65nm flash chips. After some time :( searching for bugs in our board or soft, we have discovered that those chips have a small but annoying bug, documented in "Numonyx Axcell P33/P30 256-Mbit Specification Update" It states : When customer uses [...] block unlock, the block lock status might be altered inadvertently. Lock status might be set to either 01h or 03h unexpectedly (00h as expected data), which leads to program/erase failure on certain blocks. A working workaround is given, which I have applied and tested with success : Workaround: If the interval between 60h and its subsequent command can be guaranteed within 20us, Option I is recommended, otherwise Option II (involves hardware) should be selected. Option I: The table below lists the detail command sequences: Command Data bus Address bus Remarks Sequence 1 90h Block Address Read Lock Status 2 Read Block Address + 02h (2)(3) (1) 3 60h Block Address (2)(3) (1) Lock/Unlock/RCR Configuration 4 D0h/01h/03h Block Address Notes: (1) Block Address refers to RCR configuration data only when the 60h command sequence is used to set RCR register combined with 03h subsequent command. (2) For the third and fourth command sequences, the Block Address must be the same. (3) The interval between 60h command and its subsequent D0h/01h/2Fh/03h commands should be less than 20us. And here is a log comparison of a simple (destructive) flash test without and with the workaround. diff without-numonyx-workaround.log with-numonyx-workaround.log -U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:07:47) +U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:25:19) CPU: Freescale MCF5484 CPU CLK 200 MHz BUS CLK 100 MHz Board: Macq Electronique ME2060 I2C: ready DRAM: 64 MiB FLASH: 32 MiB In: serial Out: serial Err: serial Net: FEC0, FEC1 -> flinfo Bank # 1: CFI conformant FLASH (16 x 16) Size: 32 MB in 259 Sectors Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8922 Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 5 ms, buffer size: 1024 bytes Sector Start Addresses: FE000000 RO FE008000 RO FE010000 RO FE018000 RO FE020000 RO FE040000 RO FE060000 RO FE080000 RO FE0A0000 RO FE0C0000 RO ... FFF80000 RO FFFA0000 RO FFFC0000 RO FFFE0000 RO -> protect off all Un-Protect Flash Bank # 1 ................... done -> erase all Erase Flash Bank # 1 ................... done -> cp.b 1000000 fe000000 2000000 -Copy to Flash... Flash not Erased +Copy to Flash... done -> Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-17 16:40:25 +00:00
}
break;
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
/* U-Boot only checks the first byte */
if (manufact_match(info, ATM_MANUFACT)) {
if (prot) {
flash_unlock_seq (info, 0);
flash_write_cmd (info, 0,
info->addr_unlock1,
ATM_CMD_SOFTLOCK_START);
flash_unlock_seq (info, 0);
flash_write_cmd (info, sector, 0,
ATM_CMD_LOCK_SECT);
} else {
flash_write_cmd (info, 0,
info->addr_unlock1,
AMD_CMD_UNLOCK_START);
if (info->device_id == ATM_ID_BV6416)
flash_write_cmd (info, sector,
0, ATM_CMD_UNLOCK_SECT);
}
}
if (info->legacy_unlock) {
int flag = disable_interrupts();
int lock_flag;
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0, info->addr_unlock1,
AMD_CMD_SET_PPB_ENTRY);
lock_flag = flash_isset(info, sector, 0, 0x01);
if (prot) {
if (lock_flag) {
flash_write_cmd(info, sector, 0,
AMD_CMD_PPB_LOCK_BC1);
flash_write_cmd(info, sector, 0,
AMD_CMD_PPB_LOCK_BC2);
}
debug("sector %ld %slocked\n", sector,
lock_flag ? "" : "already ");
} else {
if (!lock_flag) {
debug("unlock %ld\n", sector);
flash_write_cmd(info, 0, 0,
AMD_CMD_PPB_UNLOCK_BC1);
flash_write_cmd(info, 0, 0,
AMD_CMD_PPB_UNLOCK_BC2);
}
debug("sector %ld %sunlocked\n", sector,
!lock_flag ? "" : "already ");
}
if (flag)
enable_interrupts();
if (flash_status_check(info, sector,
info->erase_blk_tout,
prot ? "protect" : "unprotect"))
printf("status check error\n");
flash_write_cmd(info, 0, 0,
AMD_CMD_SET_PPB_EXIT_BC1);
flash_write_cmd(info, 0, 0,
AMD_CMD_SET_PPB_EXIT_BC2);
}
break;
#ifdef CONFIG_FLASH_CFI_LEGACY
case CFI_CMDSET_AMD_LEGACY:
flash_write_cmd (info, sector, 0, FLASH_CMD_CLEAR_STATUS);
flash_write_cmd (info, sector, 0, FLASH_CMD_PROTECT);
if (prot)
flash_write_cmd (info, sector, 0, FLASH_CMD_PROTECT_SET);
else
flash_write_cmd (info, sector, 0, FLASH_CMD_PROTECT_CLEAR);
#endif
};
/*
* Flash needs to be in status register read mode for
* flash_full_status_check() to work correctly
*/
flash_write_cmd(info, sector, 0, FLASH_CMD_READ_STATUS);
if ((retcode =
flash_full_status_check (info, sector, info->erase_blk_tout,
prot ? "protect" : "unprotect")) == 0) {
info->protect[sector] = prot;
/*
* On some of Intel's flash chips (marked via legacy_unlock)
* unprotect unprotects all locking.
*/
if ((prot == 0) && (info->legacy_unlock)) {
flash_sect_t i;
for (i = 0; i < info->sector_count; i++) {
if (info->protect[i])
flash_real_protect (info, i, 1);
}
}
}
return retcode;
}
/*-----------------------------------------------------------------------
* flash_read_user_serial - read the OneTimeProgramming cells
*/
void flash_read_user_serial (flash_info_t * info, void *buffer, int offset,
int len)
{
uchar *src;
uchar *dst;
dst = buffer;
src = flash_map (info, 0, FLASH_OFFSET_USER_PROTECTION);
flash_write_cmd (info, 0, 0, FLASH_CMD_READ_ID);
memcpy (dst, src + offset, len);
flash_write_cmd (info, 0, 0, info->cmd_reset);
udelay(1);
flash_unmap(info, 0, FLASH_OFFSET_USER_PROTECTION, src);
}
/*
* flash_read_factory_serial - read the device Id from the protection area
*/
void flash_read_factory_serial (flash_info_t * info, void *buffer, int offset,
int len)
{
uchar *src;
src = flash_map (info, 0, FLASH_OFFSET_INTEL_PROTECTION);
flash_write_cmd (info, 0, 0, FLASH_CMD_READ_ID);
memcpy (buffer, src + offset, len);
flash_write_cmd (info, 0, 0, info->cmd_reset);
udelay(1);
flash_unmap(info, 0, FLASH_OFFSET_INTEL_PROTECTION, src);
}
#endif /* CONFIG_SYS_FLASH_PROTECTION */
/*-----------------------------------------------------------------------
* Reverse the order of the erase regions in the CFI QRY structure.
* This is needed for chips that are either a) correctly detected as
* top-boot, or b) buggy.
*/
static void cfi_reverse_geometry(struct cfi_qry *qry)
{
unsigned int i, j;
u32 tmp;
for (i = 0, j = qry->num_erase_regions - 1; i < j; i++, j--) {
tmp = get_unaligned(&(qry->erase_region_info[i]));
put_unaligned(get_unaligned(&(qry->erase_region_info[j])),
&(qry->erase_region_info[i]));
put_unaligned(tmp, &(qry->erase_region_info[j]));
}
}
/*-----------------------------------------------------------------------
* read jedec ids from device and set corresponding fields in info struct
*
* Note: assume cfi->vendor, cfi->portwidth and cfi->chipwidth are correct
*
*/
static void cmdset_intel_read_jedec_ids(flash_info_t *info)
{
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
udelay(1);
flash_write_cmd(info, 0, 0, FLASH_CMD_READ_ID);
udelay(1000); /* some flash are slow to respond */
info->manufacturer_id = flash_read_uchar (info,
FLASH_OFFSET_MANUFACTURER_ID);
info->device_id = (info->chipwidth == FLASH_CFI_16BIT) ?
flash_read_word (info, FLASH_OFFSET_DEVICE_ID) :
flash_read_uchar (info, FLASH_OFFSET_DEVICE_ID);
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
}
static int cmdset_intel_init(flash_info_t *info, struct cfi_qry *qry)
{
info->cmd_reset = FLASH_CMD_RESET;
cmdset_intel_read_jedec_ids(info);
flash_write_cmd(info, 0, info->cfi_offset, FLASH_CMD_CFI);
#ifdef CONFIG_SYS_FLASH_PROTECTION
/* read legacy lock/unlock bit from intel flash */
if (info->ext_addr) {
info->legacy_unlock = flash_read_uchar (info,
info->ext_addr + 5) & 0x08;
}
#endif
return 0;
}
static void cmdset_amd_read_jedec_ids(flash_info_t *info)
{
ushort bankId = 0;
uchar manuId;
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0, info->addr_unlock1, FLASH_CMD_READ_ID);
udelay(1000); /* some flash are slow to respond */
manuId = flash_read_uchar (info, FLASH_OFFSET_MANUFACTURER_ID);
/* JEDEC JEP106Z specifies ID codes up to bank 7 */
while (manuId == FLASH_CONTINUATION_CODE && bankId < 0x800) {
bankId += 0x100;
manuId = flash_read_uchar (info,
bankId | FLASH_OFFSET_MANUFACTURER_ID);
}
info->manufacturer_id = manuId;
switch (info->chipwidth){
case FLASH_CFI_8BIT:
info->device_id = flash_read_uchar (info,
FLASH_OFFSET_DEVICE_ID);
if (info->device_id == 0x7E) {
/* AMD 3-byte (expanded) device ids */
info->device_id2 = flash_read_uchar (info,
FLASH_OFFSET_DEVICE_ID2);
info->device_id2 <<= 8;
info->device_id2 |= flash_read_uchar (info,
FLASH_OFFSET_DEVICE_ID3);
}
break;
case FLASH_CFI_16BIT:
info->device_id = flash_read_word (info,
FLASH_OFFSET_DEVICE_ID);
if ((info->device_id & 0xff) == 0x7E) {
/* AMD 3-byte (expanded) device ids */
info->device_id2 = flash_read_uchar (info,
FLASH_OFFSET_DEVICE_ID2);
info->device_id2 <<= 8;
info->device_id2 |= flash_read_uchar (info,
FLASH_OFFSET_DEVICE_ID3);
}
break;
default:
break;
}
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
udelay(1);
}
static int cmdset_amd_init(flash_info_t *info, struct cfi_qry *qry)
{
info->cmd_reset = AMD_CMD_RESET;
info->cmd_erase_sector = AMD_CMD_ERASE_SECTOR;
cmdset_amd_read_jedec_ids(info);
flash_write_cmd(info, 0, info->cfi_offset, FLASH_CMD_CFI);
#ifdef CONFIG_SYS_FLASH_PROTECTION
if (info->ext_addr) {
/* read sector protect/unprotect scheme (at 0x49) */
if (flash_read_uchar(info, info->ext_addr + 9) == 0x8)
info->legacy_unlock = 1;
}
#endif
return 0;
}
#ifdef CONFIG_FLASH_CFI_LEGACY
static void flash_read_jedec_ids (flash_info_t * info)
{
info->manufacturer_id = 0;
info->device_id = 0;
info->device_id2 = 0;
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
cmdset_intel_read_jedec_ids(info);
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
cmdset_amd_read_jedec_ids(info);
break;
default:
break;
}
}
/*-----------------------------------------------------------------------
* Call board code to request info about non-CFI flash.
* board_flash_get_legacy needs to fill in at least:
* info->portwidth, info->chipwidth and info->interface for Jedec probing.
*/
static int flash_detect_legacy(phys_addr_t base, int banknum)
{
flash_info_t *info = &flash_info[banknum];
if (board_flash_get_legacy(base, banknum, info)) {
/* board code may have filled info completely. If not, we
use JEDEC ID probing. */
if (!info->vendor) {
int modes[] = {
CFI_CMDSET_AMD_STANDARD,
CFI_CMDSET_INTEL_STANDARD
};
int i;
for (i = 0; i < ARRAY_SIZE(modes); i++) {
info->vendor = modes[i];
info->start[0] =
(ulong)map_physmem(base,
info->portwidth,
MAP_NOCACHE);
if (info->portwidth == FLASH_CFI_8BIT
&& info->interface == FLASH_CFI_X8X16) {
info->addr_unlock1 = 0x2AAA;
info->addr_unlock2 = 0x5555;
} else {
info->addr_unlock1 = 0x5555;
info->addr_unlock2 = 0x2AAA;
}
flash_read_jedec_ids(info);
debug("JEDEC PROBE: ID %x %x %x\n",
info->manufacturer_id,
info->device_id,
info->device_id2);
if (jedec_flash_match(info, info->start[0]))
break;
else
unmap_physmem((void *)info->start[0],
info->portwidth);
}
}
switch(info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
info->cmd_reset = FLASH_CMD_RESET;
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_LEGACY:
info->cmd_reset = AMD_CMD_RESET;
break;
}
info->flash_id = FLASH_MAN_CFI;
return 1;
}
return 0; /* use CFI */
}
#else
static inline int flash_detect_legacy(phys_addr_t base, int banknum)
{
return 0; /* use CFI */
}
#endif
/*-----------------------------------------------------------------------
* detect if flash is compatible with the Common Flash Interface (CFI)
* http://www.jedec.org/download/search/jesd68.pdf
*/
static void flash_read_cfi (flash_info_t *info, void *buf,
unsigned int start, size_t len)
{
u8 *p = buf;
unsigned int i;
for (i = 0; i < len; i++)
p[i] = flash_read_uchar(info, start + i);
}
static void __flash_cmd_reset(flash_info_t *info)
{
/*
* We do not yet know what kind of commandset to use, so we issue
* the reset command in both Intel and AMD variants, in the hope
* that AMD flash roms ignore the Intel command.
*/
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
udelay(1);
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
}
void flash_cmd_reset(flash_info_t *info)
__attribute__((weak,alias("__flash_cmd_reset")));
static int __flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry)
{
int cfi_offset;
/* Issue FLASH reset command */
flash_cmd_reset(info);
for (cfi_offset = 0; cfi_offset < ARRAY_SIZE(flash_offset_cfi);
cfi_offset++) {
flash_write_cmd (info, 0, flash_offset_cfi[cfi_offset],
FLASH_CMD_CFI);
if (flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP, 'Q')
&& flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R')
&& flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y')) {
flash_read_cfi(info, qry, FLASH_OFFSET_CFI_RESP,
sizeof(struct cfi_qry));
info->interface = le16_to_cpu(qry->interface_desc);
info->cfi_offset = flash_offset_cfi[cfi_offset];
debug ("device interface is %d\n",
info->interface);
debug ("found port %d chip %d ",
info->portwidth, info->chipwidth);
debug ("port %d bits chip %d bits\n",
info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
/* calculate command offsets as in the Linux driver */
info->addr_unlock1 = 0x555;
info->addr_unlock2 = 0x2aa;
/*
* modify the unlock address if we are
* in compatibility mode
*/
if ( /* x8/x16 in x8 mode */
((info->chipwidth == FLASH_CFI_BY8) &&
(info->interface == FLASH_CFI_X8X16)) ||
/* x16/x32 in x16 mode */
((info->chipwidth == FLASH_CFI_BY16) &&
(info->interface == FLASH_CFI_X16X32)))
{
info->addr_unlock1 = 0xaaa;
info->addr_unlock2 = 0x555;
}
info->name = "CFI conformant";
return 1;
}
}
return 0;
}
static int flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry)
{
debug ("flash detect cfi\n");
for (info->portwidth = CONFIG_SYS_FLASH_CFI_WIDTH;
info->portwidth <= FLASH_CFI_64BIT; info->portwidth <<= 1) {
for (info->chipwidth = FLASH_CFI_BY8;
info->chipwidth <= info->portwidth;
info->chipwidth <<= 1)
if (__flash_detect_cfi(info, qry))
return 1;
}
debug ("not found\n");
return 0;
}
/*
* Manufacturer-specific quirks. Add workarounds for geometry
* reversal, etc. here.
*/
static void flash_fixup_amd(flash_info_t *info, struct cfi_qry *qry)
{
/* check if flash geometry needs reversal */
if (qry->num_erase_regions > 1) {
/* reverse geometry if top boot part */
if (info->cfi_version < 0x3131) {
/* CFI < 1.1, try to guess from device id */
if ((info->device_id & 0x80) != 0)
cfi_reverse_geometry(qry);
} else if (flash_read_uchar(info, info->ext_addr + 0xf) == 3) {
/* CFI >= 1.1, deduct from top/bottom flag */
/* note: ext_addr is valid since cfi_version > 0 */
cfi_reverse_geometry(qry);
}
}
}
static void flash_fixup_atmel(flash_info_t *info, struct cfi_qry *qry)
{
int reverse_geometry = 0;
/* Check the "top boot" bit in the PRI */
if (info->ext_addr && !(flash_read_uchar(info, info->ext_addr + 6) & 1))
reverse_geometry = 1;
/* AT49BV6416(T) list the erase regions in the wrong order.
* However, the device ID is identical with the non-broken
* AT49BV642D they differ in the high byte.
*/
if (info->device_id == 0xd6 || info->device_id == 0xd2)
reverse_geometry = !reverse_geometry;
if (reverse_geometry)
cfi_reverse_geometry(qry);
}
static void flash_fixup_stm(flash_info_t *info, struct cfi_qry *qry)
{
/* check if flash geometry needs reversal */
if (qry->num_erase_regions > 1) {
/* reverse geometry if top boot part */
if (info->cfi_version < 0x3131) {
/* CFI < 1.1, guess by device id */
if (info->device_id == 0x22CA || /* M29W320DT */
info->device_id == 0x2256 || /* M29W320ET */
info->device_id == 0x22D7) { /* M29W800DT */
cfi_reverse_geometry(qry);
}
} else if (flash_read_uchar(info, info->ext_addr + 0xf) == 3) {
/* CFI >= 1.1, deduct from top/bottom flag */
/* note: ext_addr is valid since cfi_version > 0 */
cfi_reverse_geometry(qry);
}
}
}
static void flash_fixup_sst(flash_info_t *info, struct cfi_qry *qry)
{
/*
* SST, for many recent nor parallel flashes, says they are
* CFI-conformant. This is not true, since qry struct.
* reports a std. AMD command set (0x0002), while SST allows to
* erase two different sector sizes for the same memory.
* 64KB sector (SST call it block) needs 0x30 to be erased.
* 4KB sector (SST call it sector) needs 0x50 to be erased.
* Since CFI query detect the 4KB number of sectors, users expects
* a sector granularity of 4KB, and it is here set.
*/
if (info->device_id == 0x5D23 || /* SST39VF3201B */
info->device_id == 0x5C23) { /* SST39VF3202B */
/* set sector granularity to 4KB */
info->cmd_erase_sector=0x50;
}
}
static void flash_fixup_num(flash_info_t *info, struct cfi_qry *qry)
{
/*
* The M29EW devices seem to report the CFI information wrong
* when it's in 8 bit mode.
* There's an app note from Numonyx on this issue.
* So adjust the buffer size for M29EW while operating in 8-bit mode
*/
if (((qry->max_buf_write_size) > 0x8) &&
(info->device_id == 0x7E) &&
(info->device_id2 == 0x2201 ||
info->device_id2 == 0x2301 ||
info->device_id2 == 0x2801 ||
info->device_id2 == 0x4801)) {
debug("Adjusted buffer size on Numonyx flash"
" M29EW family in 8 bit mode\n");
qry->max_buf_write_size = 0x8;
}
}
/*
* The following code cannot be run from FLASH!
*
*/
cfi_flash: fix bug introduced while recent change to flash_get_size() commit ec50a8e389863ac35bfd9d9a2e8b30187318e59e "cfi_flash: handle 'chip size exceeds address window' situation" added 3rd argument to flash_get_size() but didn't fix all the function calls from the board specific code. Many boards have their own flash_get_size() definitions in the board code and use them there, but some boards (e.g. tqm834x, tqm85xx, pdm360ng) use flash_get_size() from the cfi_flash.c driver. The bug shows up if the value of the "max_size" argument (which is not defined when calling the function with two arguments) happens to be less than "info->size". In this case on the affected boards we end up with a bank of reduced size and in the worst case might even be not able to update U-Boot or to boot the kernel from flash: => fli Bank # 1: CFI conformant FLASH (32 x 16) Size: 0 kB in 1 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 3 ms, buffer size: 64 bytes Sector Start Addresses: F0000000 RO Bank # 2: CFI conformant FLASH (32 x 16) Size: 128 MB in 512 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 3 ms, buffer size: 64 bytes Sector Start Addresses: F8000000 F8040000 F8080000 F80C0000 F8100000 F8140000 F8180000 F81C0000 F8200000 F8240000 ... E.g., updating U-Boot is not possible now: => protect off ${u-boot_addr} +${u-boot_size} Error: end address (0xf007ffff) not in flash! Bad address format => era ${u-boot_addr} +${u-boot_size} Error: end address (0xf007ffff) not in flash! Bad address format This patch removes the 3rd argument of flash_get_size() again and sets "max_size" in the function itself instead of passing it as a function argument. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-11-28 01:13:33 +00:00
ulong flash_get_size (phys_addr_t base, int banknum)
{
flash_info_t *info = &flash_info[banknum];
int i, j;
flash_sect_t sect_cnt;
phys_addr_t sector;
unsigned long tmp;
int size_ratio;
uchar num_erase_regions;
int erase_region_size;
int erase_region_count;
struct cfi_qry qry;
cfi_flash: fix bug introduced while recent change to flash_get_size() commit ec50a8e389863ac35bfd9d9a2e8b30187318e59e "cfi_flash: handle 'chip size exceeds address window' situation" added 3rd argument to flash_get_size() but didn't fix all the function calls from the board specific code. Many boards have their own flash_get_size() definitions in the board code and use them there, but some boards (e.g. tqm834x, tqm85xx, pdm360ng) use flash_get_size() from the cfi_flash.c driver. The bug shows up if the value of the "max_size" argument (which is not defined when calling the function with two arguments) happens to be less than "info->size". In this case on the affected boards we end up with a bank of reduced size and in the worst case might even be not able to update U-Boot or to boot the kernel from flash: => fli Bank # 1: CFI conformant FLASH (32 x 16) Size: 0 kB in 1 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 3 ms, buffer size: 64 bytes Sector Start Addresses: F0000000 RO Bank # 2: CFI conformant FLASH (32 x 16) Size: 128 MB in 512 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 3 ms, buffer size: 64 bytes Sector Start Addresses: F8000000 F8040000 F8080000 F80C0000 F8100000 F8140000 F8180000 F81C0000 F8200000 F8240000 ... E.g., updating U-Boot is not possible now: => protect off ${u-boot_addr} +${u-boot_size} Error: end address (0xf007ffff) not in flash! Bad address format => era ${u-boot_addr} +${u-boot_size} Error: end address (0xf007ffff) not in flash! Bad address format This patch removes the 3rd argument of flash_get_size() again and sets "max_size" in the function itself instead of passing it as a function argument. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-11-28 01:13:33 +00:00
unsigned long max_size;
memset(&qry, 0, sizeof(qry));
info->ext_addr = 0;
info->cfi_version = 0;
#ifdef CONFIG_SYS_FLASH_PROTECTION
info->legacy_unlock = 0;
#endif
info->start[0] = (ulong)map_physmem(base, info->portwidth, MAP_NOCACHE);
if (flash_detect_cfi (info, &qry)) {
info->vendor = le16_to_cpu(get_unaligned(&(qry.p_id)));
info->ext_addr = le16_to_cpu(get_unaligned(&(qry.p_adr)));
num_erase_regions = qry.num_erase_regions;
if (info->ext_addr) {
info->cfi_version = (ushort) flash_read_uchar (info,
info->ext_addr + 3) << 8;
info->cfi_version |= (ushort) flash_read_uchar (info,
info->ext_addr + 4);
}
#ifdef DEBUG
flash_printqry (&qry);
#endif
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_STANDARD:
case CFI_CMDSET_INTEL_EXTENDED:
cmdset_intel_init(info, &qry);
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
cmdset_amd_init(info, &qry);
break;
default:
printf("CFI: Unknown command set 0x%x\n",
info->vendor);
/*
* Unfortunately, this means we don't know how
* to get the chip back to Read mode. Might
* as well try an Intel-style reset...
*/
flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
return 0;
}
/* Do manufacturer-specific fixups */
switch (info->manufacturer_id) {
case 0x0001: /* AMD */
case 0x0037: /* AMIC */
flash_fixup_amd(info, &qry);
break;
case 0x001f:
flash_fixup_atmel(info, &qry);
break;
case 0x0020:
flash_fixup_stm(info, &qry);
break;
case 0x00bf: /* SST */
flash_fixup_sst(info, &qry);
break;
case 0x0089: /* Numonyx */
flash_fixup_num(info, &qry);
break;
}
debug ("manufacturer is %d\n", info->vendor);
debug ("manufacturer id is 0x%x\n", info->manufacturer_id);
debug ("device id is 0x%x\n", info->device_id);
debug ("device id2 is 0x%x\n", info->device_id2);
debug ("cfi version is 0x%04x\n", info->cfi_version);
size_ratio = info->portwidth / info->chipwidth;
/* if the chip is x8/x16 reduce the ratio by half */
if ((info->interface == FLASH_CFI_X8X16)
&& (info->chipwidth == FLASH_CFI_BY8)) {
size_ratio >>= 1;
}
debug ("size_ratio %d port %d bits chip %d bits\n",
size_ratio, info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
info->size = 1 << qry.dev_size;
/* multiply the size by the number of chips */
info->size *= size_ratio;
cfi_flash: fix bug introduced while recent change to flash_get_size() commit ec50a8e389863ac35bfd9d9a2e8b30187318e59e "cfi_flash: handle 'chip size exceeds address window' situation" added 3rd argument to flash_get_size() but didn't fix all the function calls from the board specific code. Many boards have their own flash_get_size() definitions in the board code and use them there, but some boards (e.g. tqm834x, tqm85xx, pdm360ng) use flash_get_size() from the cfi_flash.c driver. The bug shows up if the value of the "max_size" argument (which is not defined when calling the function with two arguments) happens to be less than "info->size". In this case on the affected boards we end up with a bank of reduced size and in the worst case might even be not able to update U-Boot or to boot the kernel from flash: => fli Bank # 1: CFI conformant FLASH (32 x 16) Size: 0 kB in 1 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 3 ms, buffer size: 64 bytes Sector Start Addresses: F0000000 RO Bank # 2: CFI conformant FLASH (32 x 16) Size: 128 MB in 512 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 3 ms, buffer size: 64 bytes Sector Start Addresses: F8000000 F8040000 F8080000 F80C0000 F8100000 F8140000 F8180000 F81C0000 F8200000 F8240000 ... E.g., updating U-Boot is not possible now: => protect off ${u-boot_addr} +${u-boot_size} Error: end address (0xf007ffff) not in flash! Bad address format => era ${u-boot_addr} +${u-boot_size} Error: end address (0xf007ffff) not in flash! Bad address format This patch removes the 3rd argument of flash_get_size() again and sets "max_size" in the function itself instead of passing it as a function argument. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-11-28 01:13:33 +00:00
max_size = cfi_flash_bank_size(banknum);
if (max_size && (info->size > max_size)) {
debug("[truncated from %ldMiB]", info->size >> 20);
info->size = max_size;
}
debug ("found %d erase regions\n", num_erase_regions);
sect_cnt = 0;
sector = base;
for (i = 0; i < num_erase_regions; i++) {
if (i > NUM_ERASE_REGIONS) {
printf ("%d erase regions found, only %d used\n",
num_erase_regions, NUM_ERASE_REGIONS);
break;
}
tmp = le32_to_cpu(get_unaligned(
&(qry.erase_region_info[i])));
debug("erase region %u: 0x%08lx\n", i, tmp);
erase_region_count = (tmp & 0xffff) + 1;
tmp >>= 16;
erase_region_size =
(tmp & 0xffff) ? ((tmp & 0xffff) * 256) : 128;
debug ("erase_region_count = %d erase_region_size = %d\n",
erase_region_count, erase_region_size);
for (j = 0; j < erase_region_count; j++) {
if (sector - base >= info->size)
break;
if (sect_cnt >= CONFIG_SYS_MAX_FLASH_SECT) {
printf("ERROR: too many flash sectors\n");
break;
}
info->start[sect_cnt] =
(ulong)map_physmem(sector,
info->portwidth,
MAP_NOCACHE);
sector += (erase_region_size * size_ratio);
/*
* Only read protection status from
* supported devices (intel...)
*/
switch (info->vendor) {
case CFI_CMDSET_INTEL_PROG_REGIONS:
case CFI_CMDSET_INTEL_EXTENDED:
case CFI_CMDSET_INTEL_STANDARD:
/*
* Set flash to read-id mode. Otherwise
* reading protected status is not
* guaranteed.
*/
flash_write_cmd(info, sect_cnt, 0,
FLASH_CMD_READ_ID);
info->protect[sect_cnt] =
flash_isset (info, sect_cnt,
FLASH_OFFSET_PROTECT,
FLASH_STATUS_PROTECT);
flash_write_cmd(info, sect_cnt, 0,
FLASH_CMD_RESET);
break;
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
if (!info->legacy_unlock) {
/* default: not protected */
info->protect[sect_cnt] = 0;
break;
}
/* Read protection (PPB) from sector */
flash_write_cmd(info, 0, 0,
info->cmd_reset);
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0,
info->addr_unlock1,
FLASH_CMD_READ_ID);
info->protect[sect_cnt] =
flash_isset(
info, sect_cnt,
FLASH_OFFSET_PROTECT,
FLASH_STATUS_PROTECT);
break;
default:
/* default: not protected */
info->protect[sect_cnt] = 0;
}
sect_cnt++;
}
}
info->sector_count = sect_cnt;
info->buffer_size = 1 << le16_to_cpu(qry.max_buf_write_size);
tmp = 1 << qry.block_erase_timeout_typ;
info->erase_blk_tout = tmp *
(1 << qry.block_erase_timeout_max);
tmp = (1 << qry.buf_write_timeout_typ) *
(1 << qry.buf_write_timeout_max);
/* round up when converting to ms */
info->buffer_write_tout = (tmp + 999) / 1000;
tmp = (1 << qry.word_write_timeout_typ) *
(1 << qry.word_write_timeout_max);
/* round up when converting to ms */
info->write_tout = (tmp + 999) / 1000;
info->flash_id = FLASH_MAN_CFI;
if ((info->interface == FLASH_CFI_X8X16) &&
(info->chipwidth == FLASH_CFI_BY8)) {
/* XXX - Need to test on x8/x16 in parallel. */
info->portwidth >>= 1;
}
flash_write_cmd (info, 0, 0, info->cmd_reset);
}
return (info->size);
}
#ifdef CONFIG_FLASH_CFI_MTD
void flash_set_verbose(uint v)
{
flash_verbose = v;
}
#endif
static void cfi_flash_set_config_reg(u32 base, u16 val)
{
#ifdef CONFIG_SYS_CFI_FLASH_CONFIG_REGS
/*
* Only set this config register if really defined
* to a valid value (0xffff is invalid)
*/
if (val == 0xffff)
return;
/*
* Set configuration register. Data is "encrypted" in the 16 lower
* address bits.
*/
flash_write16(FLASH_CMD_SETUP, (void *)(base + (val << 1)));
flash_write16(FLASH_CMD_SET_CR_CONFIRM, (void *)(base + (val << 1)));
/*
* Finally issue reset-command to bring device back to
* read-array mode
*/
flash_write16(FLASH_CMD_RESET, (void *)base);
#endif
}
/*-----------------------------------------------------------------------
*/
void flash_protect_default(void)
{
#if defined(CONFIG_SYS_FLASH_AUTOPROTECT_LIST)
int i;
struct apl_s {
ulong start;
ulong size;
} apl[] = CONFIG_SYS_FLASH_AUTOPROTECT_LIST;
#endif
/* Monitor protection ON by default */
#if (CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE) && \
(!defined(CONFIG_MONITOR_IS_IN_RAM))
flash_protect(FLAG_PROTECT_SET,
CONFIG_SYS_MONITOR_BASE,
CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
flash_get_info(CONFIG_SYS_MONITOR_BASE));
#endif
/* Environment protection ON by default */
#ifdef CONFIG_ENV_IS_IN_FLASH
flash_protect(FLAG_PROTECT_SET,
CONFIG_ENV_ADDR,
CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
flash_get_info(CONFIG_ENV_ADDR));
#endif
/* Redundant environment protection ON by default */
#ifdef CONFIG_ENV_ADDR_REDUND
flash_protect(FLAG_PROTECT_SET,
CONFIG_ENV_ADDR_REDUND,
CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
flash_get_info(CONFIG_ENV_ADDR_REDUND));
#endif
#if defined(CONFIG_SYS_FLASH_AUTOPROTECT_LIST)
for (i = 0; i < ARRAY_SIZE(apl); i++) {
debug("autoprotecting from %08lx to %08lx\n",
apl[i].start, apl[i].start + apl[i].size - 1);
flash_protect(FLAG_PROTECT_SET,
apl[i].start,
apl[i].start + apl[i].size - 1,
flash_get_info(apl[i].start));
}
#endif
}
unsigned long flash_init (void)
{
unsigned long size = 0;
int i;
#ifdef CONFIG_SYS_FLASH_PROTECTION
/* read environment from EEPROM */
char s[64];
getenv_f("unlock", s, sizeof(s));
#endif
#ifdef CONFIG_CFI_FLASH /* for driver model */
cfi_flash_init_dm();
#endif
/* Init: no FLASHes known */
for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
flash_info[i].flash_id = FLASH_UNKNOWN;
/* Optionally write flash configuration register */
cfi_flash_set_config_reg(cfi_flash_bank_addr(i),
cfi_flash_config_reg(i));
if (!flash_detect_legacy(cfi_flash_bank_addr(i), i))
cfi_flash: fix bug introduced while recent change to flash_get_size() commit ec50a8e389863ac35bfd9d9a2e8b30187318e59e "cfi_flash: handle 'chip size exceeds address window' situation" added 3rd argument to flash_get_size() but didn't fix all the function calls from the board specific code. Many boards have their own flash_get_size() definitions in the board code and use them there, but some boards (e.g. tqm834x, tqm85xx, pdm360ng) use flash_get_size() from the cfi_flash.c driver. The bug shows up if the value of the "max_size" argument (which is not defined when calling the function with two arguments) happens to be less than "info->size". In this case on the affected boards we end up with a bank of reduced size and in the worst case might even be not able to update U-Boot or to boot the kernel from flash: => fli Bank # 1: CFI conformant FLASH (32 x 16) Size: 0 kB in 1 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 3 ms, buffer size: 64 bytes Sector Start Addresses: F0000000 RO Bank # 2: CFI conformant FLASH (32 x 16) Size: 128 MB in 512 Sectors AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E Erase timeout: 4096 ms, write timeout: 1 ms Buffer write timeout: 3 ms, buffer size: 64 bytes Sector Start Addresses: F8000000 F8040000 F8080000 F80C0000 F8100000 F8140000 F8180000 F81C0000 F8200000 F8240000 ... E.g., updating U-Boot is not possible now: => protect off ${u-boot_addr} +${u-boot_size} Error: end address (0xf007ffff) not in flash! Bad address format => era ${u-boot_addr} +${u-boot_size} Error: end address (0xf007ffff) not in flash! Bad address format This patch removes the 3rd argument of flash_get_size() again and sets "max_size" in the function itself instead of passing it as a function argument. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-11-28 01:13:33 +00:00
flash_get_size(cfi_flash_bank_addr(i), i);
size += flash_info[i].size;
if (flash_info[i].flash_id == FLASH_UNKNOWN) {
#ifndef CONFIG_SYS_FLASH_QUIET_TEST
printf ("## Unknown flash on Bank %d "
"- Size = 0x%08lx = %ld MB\n",
i+1, flash_info[i].size,
flash_info[i].size >> 20);
#endif /* CONFIG_SYS_FLASH_QUIET_TEST */
}
#ifdef CONFIG_SYS_FLASH_PROTECTION
else if (strcmp(s, "yes") == 0) {
/*
* Only the U-Boot image and it's environment
* is protected, all other sectors are
* unprotected (unlocked) if flash hardware
* protection is used (CONFIG_SYS_FLASH_PROTECTION)
* and the environment variable "unlock" is
* set to "yes".
*/
if (flash_info[i].legacy_unlock) {
int k;
/*
* Disable legacy_unlock temporarily,
* since flash_real_protect would
* relock all other sectors again
* otherwise.
*/
flash_info[i].legacy_unlock = 0;
/*
* Legacy unlocking (e.g. Intel J3) ->
* unlock only one sector. This will
* unlock all sectors.
*/
flash_real_protect (&flash_info[i], 0, 0);
flash_info[i].legacy_unlock = 1;
/*
* Manually mark other sectors as
* unlocked (unprotected)
*/
for (k = 1; k < flash_info[i].sector_count; k++)
flash_info[i].protect[k] = 0;
} else {
/*
* No legancy unlocking -> unlock all sectors
*/
flash_protect (FLAG_PROTECT_CLEAR,
flash_info[i].start[0],
flash_info[i].start[0]
+ flash_info[i].size - 1,
&flash_info[i]);
Major CFI-FLASH driver update: * Add env-variable "unlock" to handle initial state of sectors (locked/unlocked). Only the U-Boot image and it's environment is protected, all other sectors are unprotected (unlocked) if flash hardware protection is used (CFG_FLASH_PROTECTION) and the environment variable "unlock" is set to "yes". Patch by Stefan Roese, 28 Feb 2006 * Update drivers/cfi_flash.c: - find_sector() called in both versions of flash_write_cfiword() Patch by Peter Pearse, 27th Feb 2006 * CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode Patch by Jose Maria Lopez, 16 Jan 2006 * Add support for AMD/Spansion Flashes in flash_write_cfibuffer Patch by Alex Bastos and Thomas Schaefer, 2005-08-29 * Changes/fixes for drivers/cfi_flash.c: We *should* check if there are any error bits if the previous call returned ERR_OK (Otherwise we will have output an error message in flash_status_check() already.) The original code would only check for error bits if flash_status_check() returns ERR_TIMEOUT. Patch by Marcus Hall, 23 Aug 2005 * Changes/fixes for drivers/cfi_flash.c: - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c Patch by Sangmoon Kim, 19 Aug 2005 * Fixes for drivers/cfi_flash.c: - Fix wrong timeout value usage in flash_status_check() - Round write_tout up when converting to msec in flash_get_size() - Remove clearing flash status at the end of flash_write_cfibuffer() which sets Intel 28F640J3 flash back to command mode on CSB472 Patch by Tolunay Orkun, 02 July 2005
2006-02-28 14:29:58 +00:00
}
}
#endif /* CONFIG_SYS_FLASH_PROTECTION */
}
Major CFI-FLASH driver update: * Add env-variable "unlock" to handle initial state of sectors (locked/unlocked). Only the U-Boot image and it's environment is protected, all other sectors are unprotected (unlocked) if flash hardware protection is used (CFG_FLASH_PROTECTION) and the environment variable "unlock" is set to "yes". Patch by Stefan Roese, 28 Feb 2006 * Update drivers/cfi_flash.c: - find_sector() called in both versions of flash_write_cfiword() Patch by Peter Pearse, 27th Feb 2006 * CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode Patch by Jose Maria Lopez, 16 Jan 2006 * Add support for AMD/Spansion Flashes in flash_write_cfibuffer Patch by Alex Bastos and Thomas Schaefer, 2005-08-29 * Changes/fixes for drivers/cfi_flash.c: We *should* check if there are any error bits if the previous call returned ERR_OK (Otherwise we will have output an error message in flash_status_check() already.) The original code would only check for error bits if flash_status_check() returns ERR_TIMEOUT. Patch by Marcus Hall, 23 Aug 2005 * Changes/fixes for drivers/cfi_flash.c: - Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c - Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c Patch by Sangmoon Kim, 19 Aug 2005 * Fixes for drivers/cfi_flash.c: - Fix wrong timeout value usage in flash_status_check() - Round write_tout up when converting to msec in flash_get_size() - Remove clearing flash status at the end of flash_write_cfibuffer() which sets Intel 28F640J3 flash back to command mode on CSB472 Patch by Tolunay Orkun, 02 July 2005
2006-02-28 14:29:58 +00:00
flash_protect_default();
#ifdef CONFIG_FLASH_CFI_MTD
cfi_mtd_init();
#endif
return (size);
}
#ifdef CONFIG_CFI_FLASH /* for driver model */
static int cfi_flash_probe(struct udevice *dev)
{
void *blob = (void *)gd->fdt_blob;
int node = dev->of_offset;
const fdt32_t *cell;
phys_addr_t addr;
int parent, addrc, sizec;
int len, idx;
parent = fdt_parent_offset(blob, node);
of_bus_default_count_cells(blob, parent, &addrc, &sizec);
/* decode regs, there may be multiple reg tuples. */
cell = fdt_getprop(blob, node, "reg", &len);
if (!cell)
return -ENOENT;
idx = 0;
len /= sizeof(fdt32_t);
while (idx < len) {
addr = fdt_translate_address((void *)blob,
node, cell + idx);
cfi_flash_base[cfi_flash_num_flash_banks++] = addr;
idx += addrc + sizec;
}
gd->bd->bi_flashstart = cfi_flash_base[0];
return 0;
}
static const struct udevice_id cfi_flash_ids[] = {
{ .compatible = "cfi-flash" },
{ .compatible = "jedec-flash" },
{}
};
U_BOOT_DRIVER(cfi_flash) = {
.name = "cfi_flash",
.id = UCLASS_MTD,
.of_match = cfi_flash_ids,
.probe = cfi_flash_probe,
};
#endif /* CONFIG_CFI_FLASH */