u-boot/drivers/sound/wm8994.c

916 lines
22 KiB
C
Raw Normal View History

/*
* Copyright (C) 2012 Samsung Electronics
* R. Chandrasekar <rcsekar@samsung.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <asm/arch/clk.h>
#include <asm/arch/cpu.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <common.h>
#include <div64.h>
#include <fdtdec.h>
#include <i2c.h>
#include <i2s.h>
#include <sound.h>
#include <asm/arch/sound.h>
#include "wm8994.h"
#include "wm8994_registers.h"
/* defines for wm8994 system clock selection */
#define SEL_MCLK1 0x00
#define SEL_MCLK2 0x08
#define SEL_FLL1 0x10
#define SEL_FLL2 0x18
/* fll config to configure fll */
struct wm8994_fll_config {
int src; /* Source */
int in; /* Input frequency in Hz */
int out; /* output frequency in Hz */
};
/* codec private data */
struct wm8994_priv {
enum wm8994_type type; /* codec type of wolfson */
int revision; /* Revision */
int sysclk[WM8994_MAX_AIF]; /* System clock frequency in Hz */
int mclk[WM8994_MAX_AIF]; /* master clock frequency in Hz */
int aifclk[WM8994_MAX_AIF]; /* audio interface clock in Hz */
struct wm8994_fll_config fll[2]; /* fll config to configure fll */
};
/* wm 8994 supported sampling rate values */
static unsigned int src_rate[] = {
8000, 11025, 12000, 16000, 22050, 24000,
32000, 44100, 48000, 88200, 96000
};
/* op clock divisions */
static int opclk_divs[] = { 10, 20, 30, 40, 55, 60, 80, 120, 160 };
/* lr clock frame size ratio */
static int fs_ratios[] = {
64, 128, 192, 256, 348, 512, 768, 1024, 1408, 1536
};
/* bit clock divisors */
static int bclk_divs[] = {
10, 15, 20, 30, 40, 50, 60, 80, 110, 120, 160, 220, 240, 320, 440, 480,
640, 880, 960, 1280, 1760, 1920
};
static struct wm8994_priv g_wm8994_info;
static unsigned char g_wm8994_i2c_dev_addr;
static struct sound_codec_info g_codec_info;
/*
* Initialise I2C for wm 8994
*
* @param bus no i2c bus number in which wm8994 is connected
*/
static void wm8994_i2c_init(int bus_no)
{
i2c_set_bus_num(bus_no);
}
/*
* Writes value to a device register through i2c
*
* @param reg reg number to be write
* @param data data to be writen to the above registor
*
* @return int value 1 for change, 0 for no change or negative error code.
*/
static int wm8994_i2c_write(unsigned int reg, unsigned short data)
{
unsigned char val[2];
val[0] = (unsigned char)((data >> 8) & 0xff);
val[1] = (unsigned char)(data & 0xff);
debug("Write Addr : 0x%04X, Data : 0x%04X\n", reg, data);
return i2c_write(g_wm8994_i2c_dev_addr, reg, 2, val, 2);
}
/*
* Read a value from a device register through i2c
*
* @param reg reg number to be read
* @param data address of read data to be stored
*
* @return int value 0 for success, -1 in case of error.
*/
static unsigned int wm8994_i2c_read(unsigned int reg , unsigned short *data)
{
unsigned char val[2];
int ret;
ret = i2c_read(g_wm8994_i2c_dev_addr, reg, 2, val, 2);
if (ret != 0) {
debug("%s: Error while reading register %#04x\n",
__func__, reg);
return -1;
}
*data = val[0];
*data <<= 8;
*data |= val[1];
return 0;
}
/*
* update device register bits through i2c
*
* @param reg codec register
* @param mask register mask
* @param value new value
*
* @return int value 1 if change in the register value,
* 0 for no change or negative error code.
*/
static int wm8994_update_bits(unsigned int reg, unsigned short mask,
unsigned short value)
{
int change , ret = 0;
unsigned short old, new;
if (wm8994_i2c_read(reg, &old) != 0)
return -1;
new = (old & ~mask) | (value & mask);
change = (old != new) ? 1 : 0;
if (change)
ret = wm8994_i2c_write(reg, new);
if (ret < 0)
return ret;
return change;
}
/*
* Sets i2s set format
*
* @param aif_id Interface ID
* @param fmt i2S format
*
* @return -1 for error and 0 Success.
*/
int wm8994_set_fmt(int aif_id, unsigned int fmt)
{
int ms_reg;
int aif_reg;
int ms = 0;
int aif = 0;
int aif_clk = 0;
int error = 0;
switch (aif_id) {
case 1:
ms_reg = WM8994_AIF1_MASTER_SLAVE;
aif_reg = WM8994_AIF1_CONTROL_1;
aif_clk = WM8994_AIF1_CLOCKING_1;
break;
case 2:
ms_reg = WM8994_AIF2_MASTER_SLAVE;
aif_reg = WM8994_AIF2_CONTROL_1;
aif_clk = WM8994_AIF2_CLOCKING_1;
break;
default:
debug("%s: Invalid audio interface selection\n", __func__);
return -1;
}
switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
case SND_SOC_DAIFMT_CBS_CFS:
break;
case SND_SOC_DAIFMT_CBM_CFM:
ms = WM8994_AIF1_MSTR;
break;
default:
debug("%s: Invalid i2s master selection\n", __func__);
return -1;
}
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
case SND_SOC_DAIFMT_DSP_B:
aif |= WM8994_AIF1_LRCLK_INV;
case SND_SOC_DAIFMT_DSP_A:
aif |= 0x18;
break;
case SND_SOC_DAIFMT_I2S:
aif |= 0x10;
break;
case SND_SOC_DAIFMT_RIGHT_J:
break;
case SND_SOC_DAIFMT_LEFT_J:
aif |= 0x8;
break;
default:
debug("%s: Invalid i2s format selection\n", __func__);
return -1;
}
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
case SND_SOC_DAIFMT_DSP_A:
case SND_SOC_DAIFMT_DSP_B:
/* frame inversion not valid for DSP modes */
switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
case SND_SOC_DAIFMT_NB_NF:
break;
case SND_SOC_DAIFMT_IB_NF:
aif |= WM8994_AIF1_BCLK_INV;
break;
default:
debug("%s: Invalid i2s frame inverse selection\n",
__func__);
return -1;
}
break;
case SND_SOC_DAIFMT_I2S:
case SND_SOC_DAIFMT_RIGHT_J:
case SND_SOC_DAIFMT_LEFT_J:
switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
case SND_SOC_DAIFMT_NB_NF:
break;
case SND_SOC_DAIFMT_IB_IF:
aif |= WM8994_AIF1_BCLK_INV | WM8994_AIF1_LRCLK_INV;
break;
case SND_SOC_DAIFMT_IB_NF:
aif |= WM8994_AIF1_BCLK_INV;
break;
case SND_SOC_DAIFMT_NB_IF:
aif |= WM8994_AIF1_LRCLK_INV;
break;
default:
debug("%s: Invalid i2s clock polarity selection\n",
__func__);
return -1;
}
break;
default:
debug("%s: Invalid i2s format selection\n", __func__);
return -1;
}
error = wm8994_update_bits(aif_reg, WM8994_AIF1_BCLK_INV |
WM8994_AIF1_LRCLK_INV_MASK | WM8994_AIF1_FMT_MASK, aif);
error |= wm8994_update_bits(ms_reg, WM8994_AIF1_MSTR_MASK, ms);
error |= wm8994_update_bits(aif_clk, WM8994_AIF1CLK_ENA_MASK,
WM8994_AIF1CLK_ENA);
if (error < 0) {
debug("%s: codec register access error\n", __func__);
return -1;
}
return 0;
}
/*
* Sets hw params FOR WM8994
*
* @param wm8994 wm8994 information pointer
* @param aif_id Audio interface ID
* @param sampling_rate Sampling rate
* @param bits_per_sample Bits per sample
* @param Channels Channels in the given audio input
*
* @return -1 for error and 0 Success.
*/
static int wm8994_hw_params(struct wm8994_priv *wm8994, int aif_id,
unsigned int sampling_rate, unsigned int bits_per_sample,
unsigned int channels)
{
int aif1_reg;
int aif2_reg;
int bclk_reg;
int bclk = 0;
int rate_reg;
int aif1 = 0;
int aif2 = 0;
int rate_val = 0;
int id = aif_id - 1;
int i, cur_val, best_val, bclk_rate, best;
unsigned short reg_data;
int ret = 0;
switch (aif_id) {
case 1:
aif1_reg = WM8994_AIF1_CONTROL_1;
aif2_reg = WM8994_AIF1_CONTROL_2;
bclk_reg = WM8994_AIF1_BCLK;
rate_reg = WM8994_AIF1_RATE;
break;
case 2:
aif1_reg = WM8994_AIF2_CONTROL_1;
aif2_reg = WM8994_AIF2_CONTROL_2;
bclk_reg = WM8994_AIF2_BCLK;
rate_reg = WM8994_AIF2_RATE;
break;
default:
return -1;
}
bclk_rate = sampling_rate * 32;
switch (bits_per_sample) {
case 16:
bclk_rate *= 16;
break;
case 20:
bclk_rate *= 20;
aif1 |= 0x20;
break;
case 24:
bclk_rate *= 24;
aif1 |= 0x40;
break;
case 32:
bclk_rate *= 32;
aif1 |= 0x60;
break;
default:
return -1;
}
/* Try to find an appropriate sample rate; look for an exact match. */
for (i = 0; i < ARRAY_SIZE(src_rate); i++)
if (src_rate[i] == sampling_rate)
break;
if (i == ARRAY_SIZE(src_rate)) {
debug("%s: Could not get the best matching samplingrate\n",
__func__);
return -1;
}
rate_val |= i << WM8994_AIF1_SR_SHIFT;
/* AIFCLK/fs ratio; look for a close match in either direction */
best = 0;
best_val = abs((fs_ratios[0] * sampling_rate)
- wm8994->aifclk[id]);
for (i = 1; i < ARRAY_SIZE(fs_ratios); i++) {
cur_val = abs((fs_ratios[i] * sampling_rate)
- wm8994->aifclk[id]);
if (cur_val >= best_val)
continue;
best = i;
best_val = cur_val;
}
rate_val |= best;
/*
* We may not get quite the right frequency if using
* approximate clocks so look for the closest match that is
* higher than the target (we need to ensure that there enough
* BCLKs to clock out the samples).
*/
best = 0;
for (i = 0; i < ARRAY_SIZE(bclk_divs); i++) {
cur_val = (wm8994->aifclk[id] * 10 / bclk_divs[i]) - bclk_rate;
if (cur_val < 0) /* BCLK table is sorted */
break;
best = i;
}
if (i == ARRAY_SIZE(bclk_divs)) {
debug("%s: Could not get the best matching bclk division\n",
__func__);
return -1;
}
bclk_rate = wm8994->aifclk[id] * 10 / bclk_divs[best];
bclk |= best << WM8994_AIF1_BCLK_DIV_SHIFT;
if (wm8994_i2c_read(aif1_reg, &reg_data) != 0) {
debug("%s: AIF1 register read Failed\n", __func__);
return -1;
}
if ((channels == 1) && ((reg_data & 0x18) == 0x18))
aif2 |= WM8994_AIF1_MONO;
if (wm8994->aifclk[id] == 0) {
debug("%s:Audio interface clock not set\n", __func__);
return -1;
}
ret = wm8994_update_bits(aif1_reg, WM8994_AIF1_WL_MASK, aif1);
ret |= wm8994_update_bits(aif2_reg, WM8994_AIF1_MONO, aif2);
ret |= wm8994_update_bits(bclk_reg, WM8994_AIF1_BCLK_DIV_MASK, bclk);
ret |= wm8994_update_bits(rate_reg, WM8994_AIF1_SR_MASK |
WM8994_AIF1CLK_RATE_MASK, rate_val);
debug("rate vale = %x , bclk val= %x\n", rate_val, bclk);
if (ret < 0) {
debug("%s: codec register access error\n", __func__);
return -1;
}
return 0;
}
/*
* Configures Audio interface Clock
*
* @param wm8994 wm8994 information pointer
* @param aif Audio Interface ID
*
* @return -1 for error and 0 Success.
*/
static int configure_aif_clock(struct wm8994_priv *wm8994, int aif)
{
int rate;
int reg1 = 0;
int offset;
int ret;
/* AIF(1/0) register adress offset calculated */
if (aif-1)
offset = 4;
else
offset = 0;
switch (wm8994->sysclk[aif-1]) {
case WM8994_SYSCLK_MCLK1:
reg1 |= SEL_MCLK1;
rate = wm8994->mclk[0];
break;
case WM8994_SYSCLK_MCLK2:
reg1 |= SEL_MCLK2;
rate = wm8994->mclk[1];
break;
case WM8994_SYSCLK_FLL1:
reg1 |= SEL_FLL1;
rate = wm8994->fll[0].out;
break;
case WM8994_SYSCLK_FLL2:
reg1 |= SEL_FLL2;
rate = wm8994->fll[1].out;
break;
default:
debug("%s: Invalid input clock selection [%d]\n",
__func__, wm8994->sysclk[aif-1]);
return -1;
}
/* if input clock frequenct is more than 135Mhz then divide */
if (rate >= WM8994_MAX_INPUT_CLK_FREQ) {
rate /= 2;
reg1 |= WM8994_AIF1CLK_DIV;
}
wm8994->aifclk[aif-1] = rate;
ret = wm8994_update_bits(WM8994_AIF1_CLOCKING_1 + offset,
WM8994_AIF1CLK_SRC_MASK | WM8994_AIF1CLK_DIV,
reg1);
if (aif == WM8994_AIF1)
ret |= wm8994_update_bits(WM8994_CLOCKING_1,
WM8994_AIF1DSPCLK_ENA_MASK | WM8994_SYSDSPCLK_ENA_MASK,
WM8994_AIF1DSPCLK_ENA | WM8994_SYSDSPCLK_ENA);
else if (aif == WM8994_AIF2)
ret |= wm8994_update_bits(WM8994_CLOCKING_1,
WM8994_SYSCLK_SRC | WM8994_AIF2DSPCLK_ENA_MASK |
WM8994_SYSDSPCLK_ENA_MASK, WM8994_SYSCLK_SRC |
WM8994_AIF2DSPCLK_ENA | WM8994_SYSDSPCLK_ENA);
if (ret < 0) {
debug("%s: codec register access error\n", __func__);
return -1;
}
return 0;
}
/*
* Configures Audio interface for the given frequency
*
* @param wm8994 wm8994 information
* @param aif_id Audio Interface
* @param clk_id Input Clock ID
* @param freq Sampling frequency in Hz
*
* @return -1 for error and 0 success.
*/
static int wm8994_set_sysclk(struct wm8994_priv *wm8994, int aif_id,
int clk_id, unsigned int freq)
{
int i;
int ret = 0;
wm8994->sysclk[aif_id - 1] = clk_id;
switch (clk_id) {
case WM8994_SYSCLK_MCLK1:
wm8994->mclk[0] = freq;
if (aif_id == 2) {
ret = wm8994_update_bits(WM8994_AIF1_CLOCKING_2 ,
WM8994_AIF2DAC_DIV_MASK , 0);
}
break;
case WM8994_SYSCLK_MCLK2:
/* TODO: Set GPIO AF */
wm8994->mclk[1] = freq;
break;
case WM8994_SYSCLK_FLL1:
case WM8994_SYSCLK_FLL2:
break;
case WM8994_SYSCLK_OPCLK:
/*
* Special case - a division (times 10) is given and
* no effect on main clocking.
*/
if (freq) {
for (i = 0; i < ARRAY_SIZE(opclk_divs); i++)
if (opclk_divs[i] == freq)
break;
if (i == ARRAY_SIZE(opclk_divs)) {
debug("%s frequency divisor not found\n",
__func__);
return -1;
}
ret = wm8994_update_bits(WM8994_CLOCKING_2,
WM8994_OPCLK_DIV_MASK, i);
ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_2,
WM8994_OPCLK_ENA, WM8994_OPCLK_ENA);
} else {
ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_2,
WM8994_OPCLK_ENA, 0);
}
default:
debug("%s Invalid input clock selection [%d]\n",
__func__, clk_id);
return -1;
}
ret |= configure_aif_clock(wm8994, aif_id);
if (ret < 0) {
debug("%s: codec register access error\n", __func__);
return -1;
}
return 0;
}
/*
* Initializes Volume for AIF2 to HP path
*
* @returns -1 for error and 0 Success.
*
*/
static int wm8994_init_volume_aif2_dac1(void)
{
int ret;
/* Unmute AIF2DAC */
ret = wm8994_update_bits(WM8994_AIF2_DAC_FILTERS_1,
WM8994_AIF2DAC_MUTE_MASK, 0);
ret |= wm8994_update_bits(WM8994_AIF2_DAC_LEFT_VOLUME,
WM8994_AIF2DAC_VU_MASK | WM8994_AIF2DACL_VOL_MASK,
WM8994_AIF2DAC_VU | 0xff);
ret |= wm8994_update_bits(WM8994_AIF2_DAC_RIGHT_VOLUME,
WM8994_AIF2DAC_VU_MASK | WM8994_AIF2DACR_VOL_MASK,
WM8994_AIF2DAC_VU | 0xff);
ret |= wm8994_update_bits(WM8994_DAC1_LEFT_VOLUME,
WM8994_DAC1_VU_MASK | WM8994_DAC1L_VOL_MASK |
WM8994_DAC1L_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
ret |= wm8994_update_bits(WM8994_DAC1_RIGHT_VOLUME,
WM8994_DAC1_VU_MASK | WM8994_DAC1R_VOL_MASK |
WM8994_DAC1R_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
/* Head Phone Volume */
ret |= wm8994_i2c_write(WM8994_LEFT_OUTPUT_VOLUME, 0x12D);
ret |= wm8994_i2c_write(WM8994_RIGHT_OUTPUT_VOLUME, 0x12D);
if (ret < 0) {
debug("%s: codec register access error\n", __func__);
return -1;
}
return 0;
}
/*
* Initializes Volume for AIF1 to HP path
*
* @returns -1 for error and 0 Success.
*
*/
static int wm8994_init_volume_aif1_dac1(void)
{
int ret = 0;
/* Unmute AIF1DAC */
ret |= wm8994_i2c_write(WM8994_AIF1_DAC_FILTERS_1, 0x0000);
ret |= wm8994_update_bits(WM8994_DAC1_LEFT_VOLUME,
WM8994_DAC1_VU_MASK | WM8994_DAC1L_VOL_MASK |
WM8994_DAC1L_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
ret |= wm8994_update_bits(WM8994_DAC1_RIGHT_VOLUME,
WM8994_DAC1_VU_MASK | WM8994_DAC1R_VOL_MASK |
WM8994_DAC1R_MUTE_MASK, WM8994_DAC1_VU | 0xc0);
/* Head Phone Volume */
ret |= wm8994_i2c_write(WM8994_LEFT_OUTPUT_VOLUME, 0x12D);
ret |= wm8994_i2c_write(WM8994_RIGHT_OUTPUT_VOLUME, 0x12D);
if (ret < 0) {
debug("%s: codec register access error\n", __func__);
return -1;
}
return 0;
}
/*
* Intialise wm8994 codec device
*
* @param wm8994 wm8994 information
*
* @returns -1 for error and 0 Success.
*/
static int wm8994_device_init(struct wm8994_priv *wm8994,
enum en_audio_interface aif_id)
{
const char *devname;
unsigned short reg_data;
int ret;
wm8994_i2c_write(WM8994_SOFTWARE_RESET, WM8994_SW_RESET);/* Reset */
ret = wm8994_i2c_read(WM8994_SOFTWARE_RESET, &reg_data);
if (ret < 0) {
debug("Failed to read ID register\n");
goto err;
}
if (reg_data == WM8994_ID) {
devname = "WM8994";
debug("Device registered as type %d\n", wm8994->type);
wm8994->type = WM8994;
} else {
debug("Device is not a WM8994, ID is %x\n", ret);
ret = -1;
goto err;
}
ret = wm8994_i2c_read(WM8994_CHIP_REVISION, &reg_data);
if (ret < 0) {
debug("Failed to read revision register: %d\n", ret);
goto err;
}
wm8994->revision = reg_data;
debug("%s revision %c\n", devname, 'A' + wm8994->revision);
/* VMID Selection */
ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_1,
WM8994_VMID_SEL_MASK | WM8994_BIAS_ENA_MASK, 0x3);
/* Charge Pump Enable */
ret |= wm8994_update_bits(WM8994_CHARGE_PUMP_1, WM8994_CP_ENA_MASK,
WM8994_CP_ENA);
/* Head Phone Power Enable */
ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_1,
WM8994_HPOUT1L_ENA_MASK, WM8994_HPOUT1L_ENA);
ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_1,
WM8994_HPOUT1R_ENA_MASK, WM8994_HPOUT1R_ENA);
if (aif_id == WM8994_AIF1) {
ret |= wm8994_i2c_write(WM8994_POWER_MANAGEMENT_2,
WM8994_TSHUT_ENA | WM8994_MIXINL_ENA |
WM8994_MIXINR_ENA | WM8994_IN2L_ENA |
WM8994_IN2R_ENA);
ret |= wm8994_i2c_write(WM8994_POWER_MANAGEMENT_4,
WM8994_ADCL_ENA | WM8994_ADCR_ENA |
WM8994_AIF1ADC1R_ENA |
WM8994_AIF1ADC1L_ENA);
/* Power enable for AIF1 and DAC1 */
ret |= wm8994_i2c_write(WM8994_POWER_MANAGEMENT_5,
WM8994_AIF1DACL_ENA |
WM8994_AIF1DACR_ENA |
WM8994_DAC1L_ENA | WM8994_DAC1R_ENA);
} else if (aif_id == WM8994_AIF2) {
/* Power enable for AIF2 and DAC1 */
ret |= wm8994_update_bits(WM8994_POWER_MANAGEMENT_5,
WM8994_AIF2DACL_ENA_MASK | WM8994_AIF2DACR_ENA_MASK |
WM8994_DAC1L_ENA_MASK | WM8994_DAC1R_ENA_MASK,
WM8994_AIF2DACL_ENA | WM8994_AIF2DACR_ENA |
WM8994_DAC1L_ENA | WM8994_DAC1R_ENA);
}
/* Head Phone Initialisation */
ret |= wm8994_update_bits(WM8994_ANALOGUE_HP_1,
WM8994_HPOUT1L_DLY_MASK | WM8994_HPOUT1R_DLY_MASK,
WM8994_HPOUT1L_DLY | WM8994_HPOUT1R_DLY);
ret |= wm8994_update_bits(WM8994_DC_SERVO_1,
WM8994_DCS_ENA_CHAN_0_MASK |
WM8994_DCS_ENA_CHAN_1_MASK , WM8994_DCS_ENA_CHAN_0 |
WM8994_DCS_ENA_CHAN_1);
ret |= wm8994_update_bits(WM8994_ANALOGUE_HP_1,
WM8994_HPOUT1L_DLY_MASK |
WM8994_HPOUT1R_DLY_MASK | WM8994_HPOUT1L_OUTP_MASK |
WM8994_HPOUT1R_OUTP_MASK |
WM8994_HPOUT1L_RMV_SHORT_MASK |
WM8994_HPOUT1R_RMV_SHORT_MASK, WM8994_HPOUT1L_DLY |
WM8994_HPOUT1R_DLY | WM8994_HPOUT1L_OUTP |
WM8994_HPOUT1R_OUTP | WM8994_HPOUT1L_RMV_SHORT |
WM8994_HPOUT1R_RMV_SHORT);
/* MIXER Config DAC1 to HP */
ret |= wm8994_update_bits(WM8994_OUTPUT_MIXER_1,
WM8994_DAC1L_TO_HPOUT1L_MASK, WM8994_DAC1L_TO_HPOUT1L);
ret |= wm8994_update_bits(WM8994_OUTPUT_MIXER_2,
WM8994_DAC1R_TO_HPOUT1R_MASK, WM8994_DAC1R_TO_HPOUT1R);
if (aif_id == WM8994_AIF1) {
/* Routing AIF1 to DAC1 */
ret |= wm8994_i2c_write(WM8994_DAC1_LEFT_MIXER_ROUTING,
WM8994_AIF1DAC1L_TO_DAC1L);
ret |= wm8994_i2c_write(WM8994_DAC1_RIGHT_MIXER_ROUTING,
WM8994_AIF1DAC1R_TO_DAC1R);
/* GPIO Settings for AIF1 */
ret |= wm8994_i2c_write(WM8994_GPIO_1, WM8994_GPIO_DIR_OUTPUT
| WM8994_GPIO_FUNCTION_I2S_CLK
| WM8994_GPIO_INPUT_DEBOUNCE);
ret |= wm8994_init_volume_aif1_dac1();
} else if (aif_id == WM8994_AIF2) {
/* Routing AIF2 to DAC1 */
ret |= wm8994_update_bits(WM8994_DAC1_LEFT_MIXER_ROUTING,
WM8994_AIF2DACL_TO_DAC1L_MASK,
WM8994_AIF2DACL_TO_DAC1L);
ret |= wm8994_update_bits(WM8994_DAC1_RIGHT_MIXER_ROUTING,
WM8994_AIF2DACR_TO_DAC1R_MASK,
WM8994_AIF2DACR_TO_DAC1R);
/* GPIO Settings for AIF2 */
/* B CLK */
ret |= wm8994_update_bits(WM8994_GPIO_3, WM8994_GPIO_DIR_MASK |
WM8994_GPIO_FUNCTION_MASK ,
WM8994_GPIO_DIR_OUTPUT);
/* LR CLK */
ret |= wm8994_update_bits(WM8994_GPIO_4, WM8994_GPIO_DIR_MASK |
WM8994_GPIO_FUNCTION_MASK,
WM8994_GPIO_DIR_OUTPUT);
/* DATA */
ret |= wm8994_update_bits(WM8994_GPIO_5, WM8994_GPIO_DIR_MASK |
WM8994_GPIO_FUNCTION_MASK,
WM8994_GPIO_DIR_OUTPUT);
ret |= wm8994_init_volume_aif2_dac1();
}
if (ret < 0)
goto err;
debug("%s: Codec chip init ok\n", __func__);
return 0;
err:
debug("%s: Codec chip init error\n", __func__);
return -1;
}
/*
* Gets fdt values for wm8994 config parameters
*
* @param pcodec_info codec information structure
* @param blob FDT blob
* @return int value, 0 for success
*/
static int get_codec_values(struct sound_codec_info *pcodec_info,
const void *blob)
{
int error = 0;
#ifdef CONFIG_OF_CONTROL
enum fdt_compat_id compat;
int node;
int parent;
/* Get the node from FDT for codec */
node = fdtdec_next_compatible(blob, 0, COMPAT_WOLFSON_WM8994_CODEC);
if (node <= 0) {
debug("EXYNOS_SOUND: No node for codec in device tree\n");
debug("node = %d\n", node);
return -1;
}
parent = fdt_parent_offset(blob, node);
if (parent < 0) {
debug("%s: Cannot find node parent\n", __func__);
return -1;
}
compat = fdtdec_lookup(blob, parent);
switch (compat) {
case COMPAT_SAMSUNG_S3C2440_I2C:
pcodec_info->i2c_bus = i2c_get_bus_num_fdt(parent);
error |= pcodec_info->i2c_bus;
debug("i2c bus = %d\n", pcodec_info->i2c_bus);
pcodec_info->i2c_dev_addr = fdtdec_get_int(blob, node,
"reg", 0);
error |= pcodec_info->i2c_dev_addr;
debug("i2c dev addr = %d\n", pcodec_info->i2c_dev_addr);
break;
default:
debug("%s: Unknown compat id %d\n", __func__, compat);
return -1;
}
#else
pcodec_info->i2c_bus = AUDIO_I2C_BUS;
pcodec_info->i2c_dev_addr = AUDIO_I2C_REG;
debug("i2c dev addr = %d\n", pcodec_info->i2c_dev_addr);
#endif
pcodec_info->codec_type = CODEC_WM_8994;
if (error == -1) {
debug("fail to get wm8994 codec node properties\n");
return -1;
}
return 0;
}
/* WM8994 Device Initialisation */
int wm8994_init(const void *blob, enum en_audio_interface aif_id,
int sampling_rate, int mclk_freq,
int bits_per_sample, unsigned int channels)
{
int ret = 0;
struct sound_codec_info *pcodec_info = &g_codec_info;
/* Get the codec Values */
if (get_codec_values(pcodec_info, blob) < 0) {
debug("FDT Codec values failed\n");
return -1;
}
/* shift the device address by 1 for 7 bit addressing */
g_wm8994_i2c_dev_addr = pcodec_info->i2c_dev_addr;
wm8994_i2c_init(pcodec_info->i2c_bus);
if (pcodec_info->codec_type == CODEC_WM_8994) {
g_wm8994_info.type = WM8994;
} else {
debug("%s: Codec id [%d] not defined\n", __func__,
pcodec_info->codec_type);
return -1;
}
ret = wm8994_device_init(&g_wm8994_info, aif_id);
if (ret < 0) {
debug("%s: wm8994 codec chip init failed\n", __func__);
return ret;
}
ret = wm8994_set_sysclk(&g_wm8994_info, aif_id, WM8994_SYSCLK_MCLK1,
mclk_freq);
if (ret < 0) {
debug("%s: wm8994 codec set sys clock failed\n", __func__);
return ret;
}
ret = wm8994_hw_params(&g_wm8994_info, aif_id, sampling_rate,
bits_per_sample, channels);
if (ret == 0) {
ret = wm8994_set_fmt(aif_id, SND_SOC_DAIFMT_I2S |
SND_SOC_DAIFMT_NB_NF |
SND_SOC_DAIFMT_CBS_CFS);
}
return ret;
}