u-boot/arch/arm/mach-omap2/am33xx/chilisom.c

186 lines
5.5 KiB
C
Raw Normal View History

/*
* Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
* Copyright (C) 2017, Grinn - http://grinn-global.com/
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/arch/clock.h>
#include <asm/arch/clk_synthesizer.h>
#include <asm/arch/cpu.h>
#include <asm/arch/ddr_defs.h>
#include <asm/arch/hardware.h>
#include <asm/arch/omap.h>
#include <asm/arch/mem.h>
#include <asm/arch/mux.h>
#include <asm/arch/sys_proto.h>
#include <asm/emif.h>
#include <asm/io.h>
#include <errno.h>
#include <i2c.h>
#include <power/tps65217.h>
#include <spl.h>
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
static struct module_pin_mux i2c0_pin_mux[] = {
{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
PULLUDEN | SLEWCTRL)}, /* I2C_DATA */
{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
PULLUDEN | SLEWCTRL)}, /* I2C_SCLK */
{-1},
};
static struct module_pin_mux nand_pin_mux[] = {
{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
{-1},
};
static void enable_i2c0_pin_mux(void)
{
configure_module_pin_mux(i2c0_pin_mux);
}
void chilisom_enable_pin_mux(void)
{
/* chilisom pin mux */
configure_module_pin_mux(nand_pin_mux);
}
static const struct ddr_data ddr3_chilisom_data = {
.datardsratio0 = MT41K256M16HA125E_RD_DQS,
.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
};
static const struct cmd_control ddr3_chilisom_cmd_ctrl_data = {
.cmd0csratio = MT41K256M16HA125E_RATIO,
.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
.cmd1csratio = MT41K256M16HA125E_RATIO,
.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
.cmd2csratio = MT41K256M16HA125E_RATIO,
.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
};
static struct emif_regs ddr3_chilisom_emif_reg_data = {
.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
.ocp_config = 0x00141414,
.zq_config = MT41K256M16HA125E_ZQ_CFG,
.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
};
void chilisom_spl_board_init(void)
{
int mpu_vdd;
int usb_cur_lim;
enable_i2c0_pin_mux();
/* Get the frequency */
dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
if (i2c_probe(TPS65217_CHIP_PM))
return;
/*
* Increase USB current limit to 1300mA or 1800mA and set
* the MPU voltage controller as needed.
*/
if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
} else {
usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
}
if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
TPS65217_POWER_PATH,
usb_cur_lim,
TPS65217_USB_INPUT_CUR_LIMIT_MASK))
puts("tps65217_reg_write failure\n");
/* Set DCDC3 (CORE) voltage to 1.125V */
if (tps65217_voltage_update(TPS65217_DEFDCDC3,
TPS65217_DCDC_VOLT_SEL_1125MV)) {
puts("tps65217_voltage_update failure\n");
return;
}
/* Set CORE Frequencies to OPP100 */
do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
/* Set DCDC2 (MPU) voltage */
if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
puts("tps65217_voltage_update failure\n");
return;
}
/* Set LDO3 to 1.8V and LDO4 to 3.3V */
if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
TPS65217_DEFLS1,
TPS65217_LDO_VOLTAGE_OUT_1_8,
TPS65217_LDO_MASK))
puts("tps65217_reg_write failure\n");
if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
TPS65217_DEFLS2,
TPS65217_LDO_VOLTAGE_OUT_3_3,
TPS65217_LDO_MASK))
puts("tps65217_reg_write failure\n");
/* Set MPU Frequency to what we detected now that voltages are set */
do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
}
#define OSC (V_OSCK/1000000)
const struct dpll_params dpll_ddr_chilisom = {
400, OSC-1, 1, -1, -1, -1, -1};
const struct dpll_params *get_dpll_ddr_params(void)
{
return &dpll_ddr_chilisom;
}
const struct ctrl_ioregs ioregs_chilisom = {
.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
};
void sdram_init(void)
{
config_ddr(400, &ioregs_chilisom,
&ddr3_chilisom_data,
&ddr3_chilisom_cmd_ctrl_data,
&ddr3_chilisom_emif_reg_data, 0);
}
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */