u-boot/include/configs/ML2.h

256 lines
8 KiB
C
Raw Normal View History

2002-11-03 00:38:21 +00:00
/*
* ML2.h: ML2 specific config options
*
* Copyright 2002 Mind NV
*
* http://www.mind.be/
*
* Author : Peter De Schrijver (p2@mind.be)
*
* Derived from : other configuration header files in this tree
*
* This software may be used and distributed according to the terms of
* the GNU General Public License (GPL) version 2, incorporated herein by
* reference. Drivers based on or derived from this code fall under the GPL
* and must retain the authorship, copyright and this license notice. This
* file is not a complete program and may only be used when the entire
* program is licensed under the GPL.
*
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_405 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_ML2 1 /* ...on a ML2 board */
#define CONFIG_ENV_IS_IN_FLASH 1
2002-11-03 00:38:21 +00:00
#ifdef CONFIG_ENV_IS_IN_NVRAM
#undef CONFIG_ENV_IS_IN_FLASH
2002-11-03 00:38:21 +00:00
#else
#ifdef CONFIG_ENV_IS_IN_FLASH
#undef CONFIG_ENV_IS_IN_NVRAM
2002-11-03 00:38:21 +00:00
#endif
#endif
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
#if 1
#define CONFIG_BOOTCOMMAND "bootm" /* autoboot command */
#else
#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
#endif
#define CONFIG_PREBOOT "fsload 0x00100000 /boot/image"
#if 0
#define CONFIG_BOOTARGS "root=/dev/nfs " \
"ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
"nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
#else
#define CONFIG_BOOTARGS "root=/dev/mtdblock2 " \
"console=ttyS0 console=tty"
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
2002-11-03 00:38:21 +00:00
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_KGDB
#define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_ELF
#define CONFIG_CMD_JFFS2
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_RTC
#undef CONFIG_CMD_PCI
#undef CONFIG_CMD_I2C
2002-11-03 00:38:21 +00:00
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SYS_CLK_FREQ 50000000
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
2002-11-03 00:38:21 +00:00
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
2002-11-03 00:38:21 +00:00
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
2002-11-03 00:38:21 +00:00
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
2002-11-03 00:38:21 +00:00
/*
* If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
* Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
2002-11-03 00:38:21 +00:00
* The Linux BASE_BAUD define should match this configuration.
* baseBaud = cpuClock/(uartDivisor*16)
* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
2002-11-03 00:38:21 +00:00
* set Linux BASE_BAUD to 403200.
*/
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CONFIG_SYS_BASE_BAUD (3125000*16)
#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_BASE_BAUD
#define CONFIG_SYS_DUART_CHAN 0
#define CONFIG_SYS_NS16550_COM1 0xa0001003
#define CONFIG_SYS_NS16550_COM2 0xa0011003
#define CONFIG_SYS_NS16550_REG_SIZE -4
#define CONFIG_SYS_NS16550 1
#define CONFIG_SYS_INIT_CHAN1 1
#define CONFIG_SYS_INIT_CHAN2 1
2002-11-03 00:38:21 +00:00
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
2002-11-03 00:38:21 +00:00
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
2002-11-03 00:38:21 +00:00
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
2002-11-03 00:38:21 +00:00
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
2002-11-03 00:38:21 +00:00
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0x18000000
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
2002-11-03 00:38:21 +00:00
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
2002-11-03 00:38:21 +00:00
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
2002-11-03 00:38:21 +00:00
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
2002-11-03 00:38:21 +00:00
/* BEG ENVIRONNEMENT FLASH */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OFFSET 0x00050000 /* Offset of Environment Sector */
#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */
2002-11-03 00:38:21 +00:00
#endif
/* END ENVIRONNEMENT FLASH */
/*-----------------------------------------------------------------------
* NVRAM organization
*/
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */
2002-11-03 00:38:21 +00:00
#ifdef CONFIG_ENV_IS_IN_NVRAM
#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
#define CONFIG_ENV_ADDR \
(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
2002-11-03 00:38:21 +00:00
#endif
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
2002-11-03 00:38:21 +00:00
#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
/* Configuration Port location */
#define CONFIG_PORT_ADDR 0xF0000500
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */
#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
2002-11-03 00:38:21 +00:00
/*-----------------------------------------------------------------------
* Definitions for Serial Presence Detect EEPROM address
* (to get SDRAM settings)
*/
#define SPD_EEPROM_ADDRESS 0x50
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if defined(CONFIG_CMD_KGDB)
2002-11-03 00:38:21 +00:00
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* JFFS2 partitions
*
*/
/* No command line, one static partition, whole device */
#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00080000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor0=ml2-0"
#define MTDPARTS_DEFAULT "mtdparts=ml2-0:-@512k(jffs2)"
*/
2002-11-03 00:38:21 +00:00
#endif /* __CONFIG_H */