u-boot/include/configs/pcm058.h

141 lines
3.8 KiB
C
Raw Normal View History

/*
* Copyright (C) Stefano Babic <sbabic@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __PCM058_CONFIG_H
#define __PCM058_CONFIG_H
#include <config_distro_defaults.h>
#ifdef CONFIG_SPL
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_YMODEM_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_DMA_SUPPORT
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024)
#include "imx6_spl.h"
#endif
#include "mx6_common.h"
/* Thermal */
#define CONFIG_IMX_THERMAL
/* Serial */
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART2_BASE
#define CONFIG_CONSOLE_DEV "ttymxc1"
#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
/* Early setup */
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_DISPLAY_BOARDINFO_LATE
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (8 * SZ_1M)
/* Ethernet */
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 3
#define CONFIG_PHYLIB
#define CONFIG_PHY_MICREL
#define CONFIG_PHY_KSZ9031
/* SPI Flash */
#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_SPEED 100000
#ifndef CONFIG_SPL_BUILD
#define CONFIG_CMD_NAND
/* Enable NAND support */
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_NAND_MXS
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION
#endif
/* DMA stuff, needed for GPMI/MXS NAND support */
#define CONFIG_APBH_DMA
#define CONFIG_APBH_DMA_BURST
#define CONFIG_APBH_DMA_BURST8
/* Filesystem support */
#define CONFIG_LZO
#define CONFIG_CMD_UBIFS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_PARTITIONS
#define CONFIG_MTD_DEVICE
#define MTDIDS_DEFAULT "nand0=nand"
#define MTDPARTS_DEFAULT "mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
/* Various command support */
#define CONFIG_CMD_BMODE /* set eFUSE shadow for a boot dev and reset */
#define CONFIG_CMD_HDMIDETECT /* detect HDMI output device */
#define CONFIG_CMD_GSC
#define CONFIG_CMD_EECONFIG /* Gateworks EEPROM config cmd */
#define CONFIG_CMD_UBI
#define CONFIG_RBTREE
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SYS_FSL_USDHC_NUM 1
/* Environment organization */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE (16 * 1024)
#define CONFIG_ENV_OFFSET (1024 * SZ_1K)
#define CONFIG_ENV_SECT_SIZE (64 * SZ_1K)
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#ifdef CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET (0x1E0000)
#define CONFIG_ENV_SECT_SIZE (128 * SZ_1K)
#endif
#endif