u-boot/include/configs/linkstation.h

514 lines
18 KiB
C
Raw Normal View History

/*
* Copyright (C) 2006 Mihai Georgian <u-boot@linuxnotincluded.org.uk>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* Valid values for CONFIG_SYS_TEXT_BASE are:
*
* Standard configuration - all models
* 0xFFF00000 boot from flash
*
* Test configuration (boot from RAM using uloader.o)
* LinkStation HD-HLAN and KuroBox Standard
* 0x03F00000 boot from RAM
* LinkStation HD-HGLAN and KuroBox HG
* 0x07F00000 boot from RAM
*/
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xFFF00000
#endif
#if 0
#define DEBUG
#endif
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/*-----------------------------------------------------------------------
* User configurable settings:
* Mandatory settings:
* CONFIG_IPADDR_LS - the IP address of the LinkStation
* CONFIG_SERVERIP_LS - the address of the server for NFS/TFTP/DHCP/BOOTP
* Optional settins:
* CONFIG_NCIP_LS - the adress of the computer running net console
* if not configured, it will be set to
* CONFIG_SERVERIP_LS
*/
#define CONFIG_IPADDR_LS 192.168.11.150
#define CONFIG_SERVERIP_LS 192.168.11.149
#if !defined(CONFIG_IPADDR_LS) || !defined(CONFIG_SERVERIP_LS)
#error Both CONFIG_IPADDR_LS and CONFIG_SERVERIP_LS must be defined
#endif
#if !defined(CONFIG_NCIP_LS)
#define CONFIG_NCIP_LS CONFIG_SERVERIP_LS
#endif
/*----------------------------------------------------------------------
* DO NOT CHANGE ANYTHING BELOW, UNLESS YOU KNOW WHAT YOU ARE DOING
*---------------------------------------------------------------------*/
#define CONFIG_MPC8245 1
#define CONFIG_LINKSTATION 1
/*---------------------------------------
* Supported models
*
* LinkStation HDLAN /KuroBox Standard (CONFIG_HLAN)
* LinkStation old model (CONFIG_LAN) - totally untested
* LinkStation HGLAN / KuroBox HG (CONFIG_HGLAN)
*
* Models not supported yet
* TeraStatin (CONFIG_HTGL)
*/
#if defined(CONFIG_HLAN) || defined(CONFIG_LAN)
#define CONFIG_IDENT_STRING " LinkStation / KuroBox"
#elif defined(CONFIG_HGLAN)
#define CONFIG_IDENT_STRING " LinkStation HG / KuroBox HG"
#elif defined(CONFIG_HTGL)
#define CONFIG_IDENT_STRING " TeraStation"
#else
#error No LinkStation model defined
#endif
#define CONFIG_BOOTDELAY 5
#define CONFIG_ZERO_BOOTDELAY_CHECK
#undef CONFIG_BOOT_RETRY_TIME
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_PROMPT \
"Boot in %02d seconds ('s' to stop)...", bootdelay
#define CONFIG_AUTOBOOT_STOP_STR "s"
#define CONFIG_CMD_IDE
#define CONFIG_CMD_PCI
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PING
#define CONFIG_CMD_EXT2
#define CONFIG_BOOTP_MASK CONFIG_BOOTP_ALL
#define CONFIG_OF_LIBFDT 1
#define OF_STDOUT_PATH "/soc10x/serial@80004600"
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <config_cmd_default.h>
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* Default load address: 8 MB */
#define CONFIG_BOOTCOMMAND "run bootcmd1"
#define CONFIG_BOOTARGS "root=/dev/sda1 console=ttyS1,57600 netconsole=@192.168.1.7/eth0,@192.168.1.1/00:50:BF:A4:59:71 rtc-rs5c372.probe=0,0x32 debug"
#define CONFIG_NFSBOOTCOMMAND "bootp;run nfsargs;bootm"
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define XMK_STR(x) #x
#define MK_STR(x) XMK_STR(x)
#if defined(CONFIG_HLAN) || defined(CONFIG_LAN)
#define UBFILE "share/u-boot/u-boot-hd.flash.bin"
#elif defined(CONFIG_HGLAN)
#define UBFILE "share/u-boot/u-boot-hg.flash.bin"
#elif defined(CONFIG_HTGL)
#define UBFILE "share/u-boot/u-boot-ht.flash.bin"
#else
#error No LinkStation model defined
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"autoload=no\0" \
"stdin=nc\0" \
"stdout=nc\0" \
"stderr=nc\0" \
"ipaddr="MK_STR(CONFIG_IPADDR_LS)"\0" \
"netmask=255.255.255.0\0" \
"serverip="MK_STR(CONFIG_SERVERIP_LS)"\0" \
"ncip="MK_STR(CONFIG_NCIP_LS)"\0" \
"netretry=no\0" \
"nc=setenv stdin nc;setenv stdout nc;setenv stderr nc\0" \
"ser=setenv stdin serial;setenv stdout serial;setenv stderr serial\0" \
"ldaddr=800000\0" \
"hdpart=0:1\0" \
"hdfile=boot/uImage\0" \
"hdload=echo Loading ${hdpart}:${hdfile};ext2load ide ${hdpart} ${ldaddr} ${hdfile};ext2load ide ${hdpart} 7f0000 boot/kuroboxHG.dtb\0" \
"boothd=setenv bootargs " CONFIG_BOOTARGS ";bootm ${ldaddr} - 7f0000\0" \
"hdboot=run hdload;run boothd\0" \
"flboot=setenv bootargs root=/dev/hda1;bootm ffc00000\0" \
"emboot=setenv bootargs root=/dev/ram0;bootm ffc00000\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \
"bootretry=30\0" \
"bootcmd1=run hdboot;run flboot\0" \
"bootcmd2=run flboot\0" \
"bootcmd3=run emboot\0" \
"writeng=protect off fff70000 fff7ffff;era fff70000 fff7ffff;mw.l 800000 4e474e47 1;cp.b 800000 fff70000 4\0" \
"writeok=protect off fff70000 fff7ffff;era fff70000 fff7ffff;mw.l 800000 4f4b4f4b 1;cp.b 800000 fff70000 4\0" \
"ubpart=0:3\0" \
"ubfile="UBFILE"\0" \
"ubload=echo Loading ${ubpart}:${ubfile};ext2load ide ${ubpart} ${ldaddr} ${ubfile}\0" \
"ubsaddr=fff00000\0" \
"ubeaddr=fff2ffff\0" \
"ubflash=protect off ${ubsaddr} ${ubeaddr};era ${ubsaddr} ${ubeaddr};cp.b ${ldaddr} ${ubsaddr} ${filesize};cmp.b ${ldaddr} ${ubsaddr} ${filesize}\0" \
"upgrade=run ubload ubflash\0"
/*-----------------------------------------------------------------------
* PCI stuff
*/
#define CONFIG_PCI
/* Verified: CONFIG_PCI_PNP doesn't work */
#undef CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#ifndef CONFIG_PCI_PNP
/* Keep the following defines in sync with the BAT mappings */
#define PCI_ETH_IOADDR 0xbfff00
#define PCI_ETH_MEMADDR 0xbffffc00
#define PCI_IDE_IOADDR 0xbffed0
#define PCI_IDE_MEMADDR 0xbffffb00
#define PCI_USB0_IOADDR 0
#define PCI_USB0_MEMADDR 0xbfffe000
#define PCI_USB1_IOADDR 0
#define PCI_USB1_MEMADDR 0xbfffd000
#define PCI_USB2_IOADDR 0
#define PCI_USB2_MEMADDR 0xbfffcf00
#endif
/*-----------------------------------------------------------------------
* Ethernet stuff
*/
#define CONFIG_NET_MULTI
#if defined(CONFIG_LAN) || defined(CONFIG_HLAN)
#define CONFIG_TULIP
#define CONFIG_TULIP_USE_IO
#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL)
#define CONFIG_RTL8169
#endif
#define CONFIG_NET_RETRY_COUNT 5
#define CONFIG_NETCONSOLE
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0xFFC00000
#define CONFIG_SYS_FLASH_SIZE 0x00400000
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
#define CONFIG_SYS_EUMB_ADDR 0x80000000
#define CONFIG_SYS_PCI_MEM_ADDR 0xB0000000
#define CONFIG_SYS_MISC_REGION_ADDR 0xFE000000
#define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256 kB */
#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */
/* Maximum amount of RAM */
#if defined(CONFIG_HLAN) || defined(CONFIG_LAN)
#define CONFIG_SYS_MAX_RAM_SIZE 0x04000000 /* 64MB of SDRAM */
#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL)
#define CONFIG_SYS_MAX_RAM_SIZE 0x08000000 /* 128MB of SDRAM */
#else
#error Unknown LinkStation type
#endif
/*-----------------------------------------------------------------------
* Change CONFIG_SYS_TEXT_BASE in bord/linkstation/config.mk to get a RAM build
*
* RAM based builds are for testing purposes. A Linux module, uloader.o,
* exists to load U-Boot and pass control to it
*
* Always do "make clean" after changing the build type
*/
#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_RAMBOOT
#endif
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area
*/
#if 1 /* RAM is available when the first C function is called */
#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_MAX_RAM_SIZE - 0x1000)
#else
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#endif
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*----------------------------------------------------------------------
* Serial configuration
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 57600
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4600) /* Console port */
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4500) /* AVR port */
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
* For the detail description refer to the MPC8245 user's manual.
*
* Unless indicated otherwise, the values are
* taken from the orignal Linkstation boot code
*
* Most of the low level configuration setttings are normally used
* in arch/powerpc/cpu/mpc824x/cpu_init.c which is NOT used by this implementation.
* Low level initialisation is done in board/linkstation/early_init.S
* The values below are included for reference purpose only
*/
/* FIXME: 32.768 MHz is the crystal frequency but */
/* the real frequency is lower by about 0.75% */
#define CONFIG_SYS_CLK_FREQ 32768000
#define CONFIG_SYS_HZ 1000
/* Bit-field values for MCCR1. */
#define CONFIG_SYS_ROMNAL 0
#define CONFIG_SYS_ROMFAL 11
#define CONFIG_SYS_BANK0_ROW 2 /* Only bank 0 used: 13 x n x 4 */
#define CONFIG_SYS_BANK1_ROW 0
#define CONFIG_SYS_BANK2_ROW 0
#define CONFIG_SYS_BANK3_ROW 0
#define CONFIG_SYS_BANK4_ROW 0
#define CONFIG_SYS_BANK5_ROW 0
#define CONFIG_SYS_BANK6_ROW 0
#define CONFIG_SYS_BANK7_ROW 0
/* Bit-field values for MCCR2. */
#define CONFIG_SYS_TSWAIT 0
#if defined(CONFIG_LAN) || defined(CONFIG_HLAN)
#define CONFIG_SYS_REFINT 0x15e0
#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL)
#define CONFIG_SYS_REFINT 0x1580
#endif
/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
#define CONFIG_SYS_BSTOPRE 0x91c
/* Bit-field values for MCCR3. */
#define CONFIG_SYS_REFREC 7
/* Bit-field values for MCCR4. */
#define CONFIG_SYS_PRETOACT 2
#define CONFIG_SYS_ACTTOPRE 2 /* Original value was 2 */
#define CONFIG_SYS_ACTORW 2
#if defined(CONFIG_LAN) || defined(CONFIG_HLAN)
#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* For 100MHz bus */
/*#define CONFIG_SYS_SDMODE_BURSTLEN 3*/
#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL)
#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* For 133MHz bus */
/*#define CONFIG_SYS_SDMODE_BURSTLEN 2*/
#endif
#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
#define CONFIG_SYS_EXTROM 1 /* Original setting but there is no EXTROM */
#define CONFIG_SYS_REGDIMM 0
#define CONFIG_SYS_DBUS_SIZE2 1
#define CONFIG_SYS_SDMODE_WRAP 0
#define CONFIG_SYS_PGMAX 0x32 /* All boards use this setting. Original 0x92 */
#define CONFIG_SYS_SDRAM_DSCD 0x30
/* Memory bank settings.
* Only bits 20-29 are actually used from these vales to set the
* start/end addresses. The upper two bits will always be 0, and the lower
* 20 bits will be 0x00000 for a start address, or 0xfffff for an end
* address. Refer to the MPC8240 book.
*/
#define CONFIG_SYS_BANK0_START 0x00000000
#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
#define CONFIG_SYS_BANK0_ENABLE 1
#define CONFIG_SYS_BANK1_START 0x3ff00000
#define CONFIG_SYS_BANK1_END 0x3fffffff
#define CONFIG_SYS_BANK1_ENABLE 0
#define CONFIG_SYS_BANK2_START 0x3ff00000
#define CONFIG_SYS_BANK2_END 0x3fffffff
#define CONFIG_SYS_BANK2_ENABLE 0
#define CONFIG_SYS_BANK3_START 0x3ff00000
#define CONFIG_SYS_BANK3_END 0x3fffffff
#define CONFIG_SYS_BANK3_ENABLE 0
#define CONFIG_SYS_BANK4_START 0x3ff00000
#define CONFIG_SYS_BANK4_END 0x3fffffff
#define CONFIG_SYS_BANK4_ENABLE 0
#define CONFIG_SYS_BANK5_START 0x3ff00000
#define CONFIG_SYS_BANK5_END 0x3fffffff
#define CONFIG_SYS_BANK5_ENABLE 0
#define CONFIG_SYS_BANK6_START 0x3ff00000
#define CONFIG_SYS_BANK6_END 0x3fffffff
#define CONFIG_SYS_BANK6_ENABLE 0
#define CONFIG_SYS_BANK7_START 0x3ff00000
#define CONFIG_SYS_BANK7_END 0x3fffffff
#define CONFIG_SYS_BANK7_ENABLE 0
#define CONFIG_SYS_ODCR 0x15
/*----------------------------------------------------------------------
* Initial BAT mappings
*/
/* NOTES:
* 1) GUARDED and WRITETHROUGH not allowed in IBATS
* 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
*/
/* SDRAM */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* EUMB: 1MB of address space */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_EUMB_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_EUMB_ADDR | BATU_BL_1M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT1L (CONFIG_SYS_IBAT1L | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* PCI Mem: 256MB of address space */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI_MEM_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI_MEM_ADDR | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT2L (CONFIG_SYS_IBAT2L | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* PCI and local ROM/Flash: last 32MB of address space */
#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_ADDR | BATU_BL_32M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT3L (CONFIG_SYS_IBAT3L | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*
* FIXME: This doesn't appear to be true for the newer kernels
* which map more that 8 MB
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#undef CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
#define CONFIG_SYS_MAX_FLASH_SECT 72 /* Max number of sectors per flash */
#define CONFIG_SYS_FLASH_ERASE_TOUT 12000
#define CONFIG_SYS_FLASH_WRITE_TOUT 1000
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#define CONFIG_ENV_IS_IN_FLASH
/*
* The original LinkStation flash organisation uses
* 448 kB (0xFFF00000 - 0xFFF6FFFF) for the boot loader
* We use the last sector of this area to store the environment
* which leaves max. 384 kB for the U-Boot itself
*/
#define CONFIG_ENV_ADDR 0xFFF60000
#define CONFIG_ENV_SIZE 0x00010000
#define CONFIG_ENV_SECT_SIZE 0x00010000
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 32
#ifdef CONFIG_CMD_KGDB
#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* IDE/ATA definitions
*/
#undef CONFIG_IDE_LED /* No IDE LED */
#define CONFIG_IDE_RESET /* no reset for ide supported */
#define CONFIG_IDE_PREINIT /* check for units */
#define CONFIG_LBA48 /* 48 bit LBA supported */
#if defined(CONFIG_LAN) || defined(CONFIG_HLAN) || defined(CONFIG_HGLAN)
#define CONFIG_SYS_IDE_MAXBUS 1 /* Scan only 1 IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* Only 1 drive per IDE bus */
#elif defined(CONFIG_HGTL)
#define CONFIG_SYS_IDE_MAXBUS 2 /* Max. 2 IDE busses */
#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
#else
#error Config IDE: Unknown LinkStation type
#endif
#define CONFIG_SYS_ATA_BASE_ADDR 0
#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* Offset for data I/O */
#define CONFIG_SYS_ATA_REG_OFFSET 0 /* Offset for normal registers */
#define CONFIG_SYS_ATA_ALT_OFFSET 0 /* Offset for alternate registers */
/*-----------------------------------------------------------------------
* Partitions and file system
*/
#define CONFIG_DOS_PARTITION
#endif /* __CONFIG_H */