u-boot/include/configs/ecovec.h

186 lines
5.7 KiB
C
Raw Normal View History

/*
* Configuation settings for the Renesas Solutions ECOVEC board
*
* Copyright (C) 2009 - 2011 Renesas Solutions Corp.
* Copyright (C) 2009 Kuninori Morimoto <morimoto.kuninori@renesas.com>
* Copyright (C) 2010, 2011 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __ECOVEC_H
#define __ECOVEC_H
/*
* Address Interface BusWidth
*-----------------------------------------
* 0x0000_0000 U-Boot 16bit
* 0x0004_0000 Linux romImage 16bit
* 0x0014_0000 MTD for Linux 16bit
* 0x0400_0000 Internal I/O 16/32bit
* 0x0800_0000 DRAM 32bit
* 0x1800_0000 MFI 16bit
*/
#undef DEBUG
#define CONFIG_SH 1
#define CONFIG_SH4 1
#define CONFIG_SH4A 1
#define CONFIG_CPU_SH7724 1
#define CONFIG_BOARD_LATE_INIT 1
#define CONFIG_ECOVEC 1
#define CONFIG_ECOVEC_ROMIMAGE_ADDR 0xA0040000
#define CONFIG_SYS_TEXT_BASE 0x8FFC0000
#define CONFIG_CMD_FLASH
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_MII
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_ENV
#define CONFIG_CMD_USB
#define CONFIG_CMD_FAT
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_SAVEENV
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
#define CONFIG_BOOTARGS "console=ttySC0,115200"
#define CONFIG_VERSION_VARIABLE
#undef CONFIG_SHOW_BOOT_PROGRESS
/* I2C */
#define CONFIG_CMD_I2C
#define CONFIG_SH_I2C 1
#define CONFIG_HARD_I2C 1
#define CONFIG_I2C_MULTI_BUS 1
#define CONFIG_SYS_MAX_I2C_BUS 2
#define CONFIG_SYS_I2C_MODULE 1
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_SH_I2C_DATA_HIGH 4
#define CONFIG_SH_I2C_DATA_LOW 5
#define CONFIG_SH_I2C_CLOCK 41666666
#define CONFIG_SH_I2C_BASE0 0xA4470000
#define CONFIG_SH_I2C_BASE1 0xA4750000
/* Ether */
#define CONFIG_SH_ETHER 1
#define CONFIG_SH_ETHER_USE_PORT (0)
#define CONFIG_SH_ETHER_PHY_ADDR (0x1f)
#define CONFIG_PHY_SMSC 1
#define CONFIG_PHYLIB
#define CONFIG_BITBANGMII
#define CONFIG_BITBANGMII_MULTI
#define CONFIG_SH_ETHER_PHY_MODE PHY_INTERFACE_MODE_MII
/* USB / R8A66597 */
#define CONFIG_USB_R8A66597_HCD
#define CONFIG_R8A66597_BASE_ADDR 0xA4D80000
#define CONFIG_R8A66597_XTAL 0x0000 /* 12MHz */
#define CONFIG_R8A66597_LDRV 0x8000 /* 3.3V */
#define CONFIG_R8A66597_ENDIAN 0x0000 /* little */
#define CONFIG_SUPERH_ON_CHIP_R8A66597
/* undef to save memory */
#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
#define CONFIG_SYS_PROMPT "=> "
/* Buffer size for input from the Console */
#define CONFIG_SYS_CBSIZE 256
/* Buffer size for Console output */
#define CONFIG_SYS_PBSIZE 256
/* max args accepted for monitor commands */
#define CONFIG_SYS_MAXARGS 16
/* Buffer size for Boot Arguments passed to kernel */
#define CONFIG_SYS_BARGSIZE 512
/* List of legal baudrate settings for this board */
#define CONFIG_SYS_BAUDRATE_TABLE { 115200 }
/* SCIF */
#define CONFIG_SCIF_CONSOLE 1
#define CONFIG_SCIF 1
#define CONFIG_CONS_SCIF0 1
/* Suppress display of console information at boot */
#undef CONFIG_SYS_CONSOLE_INFO_QUIET
#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE (0x88000000)
#define CONFIG_SYS_SDRAM_SIZE (256 * 1024 * 1024)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024)
#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE)
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 200 * 1024 * 1024)
/* Enable alternate, more extensive, memory test */
#undef CONFIG_SYS_ALT_MEMTEST
/* Scratch address used by the alternate memory test */
#undef CONFIG_SYS_MEMTEST_SCRATCH
/* Enable temporary baudrate change while serial download */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE
/* FLASH */
#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_SYS_FLASH_CFI
#undef CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BASE (0xA0000000)
#define CONFIG_SYS_MAX_FLASH_SECT 512
/* if you use all NOR Flash , you change dip-switch. Please see Manual. */
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
/* Timeout for Flash erase operations (in ms) */
#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000)
/* Timeout for Flash write operations (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000)
/* Timeout for Flash set sector lock bit operations (in ms) */
#define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000)
/* Timeout for Flash clear lock bit operations (in ms) */
#define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000)
/*
* Use hardware flash sectors protection instead
* of U-Boot software protection
*/
#undef CONFIG_SYS_FLASH_PROTECTION
#undef CONFIG_SYS_DIRECT_FLASH_TFTP
/* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE)
/* Monitor size */
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
/* Size of DRAM reserved for malloc() use */
#define CONFIG_SYS_MALLOC_LEN (256 * 1024)
/* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_SIZE (256)
#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024)
/* ENV setting */
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OVERWRITE 1
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE)
/* Board Clock */
#define CONFIG_SYS_CLK_FREQ 41666666
#define CONFIG_SYS_TMU_CLK_DIV 4
#define CONFIG_SYS_HZ 1000
#endif /* __ECOVEC_H */