u-boot/include/configs/ve8313.h

498 lines
14 KiB
C
Raw Normal View History

/*
* Copyright (C) Freescale Semiconductor, Inc. 2006.
*
* (C) Copyright 2010
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* ve8313 board configuration file
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_DISPLAY_BOARDINFO
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1
#define CONFIG_MPC831x 1
#define CONFIG_MPC8313 1
#define CONFIG_VE8313 1
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xfe000000
#endif
#define CONFIG_PCI 1
#define CONFIG_PCI_INDIRECT_BRIDGE 1
#define CONFIG_FSL_ELBC 1
#define CONFIG_BOARD_EARLY_INIT_F 1
/*
* On-board devices
*
*/
#define CONFIG_83XX_CLKIN 32000000 /* in Hz */
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
#define CONFIG_SYS_IMMR 0xE0000000
#define CONFIG_SYS_MEMTEST_START 0x00001000
#define CONFIG_SYS_MEMTEST_END 0x07000000
#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth */
#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count */
/*
* Device configurations
*/
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
/*
* Manually set up DDR parameters, as this board does not
* have the SPD connected to I2C.
*/
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
| CSCONFIG_AP \
| CSCONFIG_ODT_RD_NEVER \
| CSCONFIG_ODT_WR_ALL \
| CSCONFIG_ROW_BIT_13 \
| CSCONFIG_COL_BIT_10)
/* 0x80840102 */
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
| (0 << TIMING_CFG0_WRT_SHIFT) \
| (3 << TIMING_CFG0_RRT_SHIFT) \
| (2 << TIMING_CFG0_WWT_SHIFT) \
| (7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
/* 0x0e720802 */
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
| (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
| (5 << TIMING_CFG1_CASLAT_SHIFT) \
| (6 << TIMING_CFG1_REFREC_SHIFT) \
| (2 << TIMING_CFG1_WRREC_SHIFT) \
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
| (2 << TIMING_CFG1_WRTORD_SHIFT))
/* 0x26256222 */
#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
| (5 << TIMING_CFG2_CPO_SHIFT) \
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
| (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
| (7 << TIMING_CFG2_FOUR_ACT_SHIFT))
/* 0x029028c7 */
#define CONFIG_SYS_DDR_INTERVAL ((0x320 << SDRAM_INTERVAL_REFINT_SHIFT) \
| (0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
/* 0x03202000 */
#define CONFIG_SYS_SDRAM_CFG (SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
| SDRAM_CFG_DBW_32)
/* 0x43080000 */
#define CONFIG_SYS_SDRAM_CFG2 0x00401000
#define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \
| (0x0232 << SDRAM_MODE_SD_SHIFT))
/* 0x44400232 */
#define CONFIG_SYS_DDR_MODE_2 0x8000C000
#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
/*0x02000000*/
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
| DDRCDR_PZ_NOMZ \
| DDRCDR_NZ_NOMZ \
| DDRCDR_M_ODR)
/* 0x73000002 */
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE 0xFE000000
#define CONFIG_SYS_FLASH_SIZE 32 /* size in MB */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \
| BR_PS_16 /* 16 bit */ \
| BR_MS_GPCM /* MSEL = GPCM */ \
| BR_V) /* valid */
#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
| OR_GPCM_CSNT \
| OR_GPCM_ACS_DIV4 \
| OR_GPCM_SCY_5 \
| OR_GPCM_TRLX_SET \
| OR_GPCM_EAD)
/* 0xfe000c55 */
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB)
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per dev */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#endif
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN (384 * 1024)
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
/*
* Local Bus LCRR and LBCR regs
*/
#define CONFIG_SYS_LCRR_EADC LCRR_EADC_3
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR 0x00040000
#define CONFIG_SYS_LBC_MRTPR 0x20000000
/*
* NAND settings
*/
#define CONFIG_SYS_NAND_BASE 0x61000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_CMD_NAND 1
#define CONFIG_NAND_FSL_ELBC 1
#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \
| BR_PS_8 \
| BR_DECC_CHK_GEN \
| BR_MS_FCM \
| BR_V) /* valid */
/* 0x61000c21 */
#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \
| OR_FCM_BCTLD \
| OR_FCM_CHT \
| OR_FCM_SCY_2 \
| OR_FCM_RST \
| OR_FCM_TRLX)
/* 0xffff90ac */
#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
/* CS2 NvRAM */
#define CONFIG_SYS_BR2_PRELIM (0x60000000 \
| BR_PS_8 \
| BR_V)
/* 0x60000801 */
#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB \
| OR_GPCM_CSNT \
| OR_GPCM_XACS \
| OR_GPCM_SCY_3 \
| OR_GPCM_TRLX_SET \
| OR_GPCM_EHTR_SET \
| OR_GPCM_EAD)
/* 0xfffe0937 */
/* local bus read write buffer mapping SRAM@0x64000000 */
#define CONFIG_SYS_BR3_PRELIM (0x62000000 \
| BR_PS_16 \
| BR_V)
/* 0x62001001 */
#define CONFIG_SYS_OR3_PRELIM (OR_AM_32MB \
| OR_GPCM_CSNT \
| OR_GPCM_XACS \
| OR_GPCM_SCY_15 \
| OR_GPCM_TRLX_SET \
| OR_GPCM_EHTR_SET \
| OR_GPCM_EAD)
/* 0xfe0009f7 */
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
#if defined(CONFIG_PCI)
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif
/*
* TSEC
*/
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#define CONFIG_TSEC1
#ifdef CONFIG_TSEC1
#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC1"
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 0x01
#define TSEC1_FLAGS 0
#define TSEC1_PHYIDX 0
#endif
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC1"
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR \
(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE 0x4000
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND \
(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_PCI
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg Buffer size */
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
/* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
/* 0x64050000 */
#define CONFIG_SYS_HRCW_LOW (\
0x20000000 /* reserved, must be set */ |\
HRCWL_DDRCM |\
HRCWL_CSB_TO_CLKIN_4X1 | \
HRCWL_CORE_TO_CSB_2_5X1)
/* 0xa0600004 */
#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \
HRCWH_PCI_ARBITER_ENABLE | \
HRCWH_CORE_ENABLE | \
HRCWH_FROM_0X00000100 | \
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_SW_WATCHDOG_DISABLE |\
HRCWH_ROM_LOC_LOCAL_16BIT | \
HRCWH_TSEC1M_IN_MII | \
HRCWH_BIG_ENDIAN | \
HRCWH_LALE_EARLY)
/* System IO Config */
#define CONFIG_SYS_SICRH (0x01000000 | \
SICRH_ETSEC2_B | \
SICRH_ETSEC2_C | \
SICRH_ETSEC2_D | \
SICRH_ETSEC2_E | \
SICRH_ETSEC2_F | \
SICRH_ETSEC2_G | \
SICRH_TSOBI1 | \
SICRH_TSOBI2)
/* 0x010fff03 */
#define CONFIG_SYS_SICRL (SICRL_LBC | \
SICRL_SPI_A | \
SICRL_SPI_B | \
SICRL_SPI_C | \
SICRL_SPI_D | \
SICRL_ETSEC2_A)
/* 0x33fc0003) */
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2 HID2_HBE
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/* DDR @ 0x00000000 */
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#if defined(CONFIG_PCI)
/* PCI @ 0x80000000 */
#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW)
#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
#else
#define CONFIG_SYS_IBAT1L (0)
#define CONFIG_SYS_IBAT1U (0)
#define CONFIG_SYS_IBAT2L (0)
#define CONFIG_SYS_IBAT2U (0)
#endif
/* PCI2 not supported on 8313 */
#define CONFIG_SYS_IBAT3L (0)
#define CONFIG_SYS_IBAT3U (0)
#define CONFIG_SYS_IBAT4L (0)
#define CONFIG_SYS_IBAT4U (0)
/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
| BATL_PP_RW \
| BATL_CACHEINHIBIT \
| BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
| BATU_BL_256M \
| BATU_VS \
| BATU_VP)
/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
/* FPGA, SRAM, NAND @ 0x60000000 */
#define CONFIG_SYS_IBAT7L (0x60000000 | BATL_PP_RW | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT7U (0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#define CONFIG_NETDEV eth0
#define CONFIG_HOSTNAME ve8313
#define CONFIG_UBOOTPATH ve8313/u-boot.bin
#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=" __stringify(CONFIG_NETDEV) "\0" \
"ethprime=" __stringify(CONFIG_TSEC1_NAME) "\0" \
"u-boot=" __stringify(CONFIG_UBOOTPATH) "\0" \
"u-boot_addr_r=100000\0" \
"load=tftp ${u-boot_addr_r} ${u-boot}\0" \
"update=protect off " __stringify(CONFIG_SYS_FLASH_BASE) \
" +${filesize};" \
"erase " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
"cp.b ${u-boot_addr_r} " __stringify(CONFIG_SYS_FLASH_BASE) \
" ${filesize};" \
"protect on " __stringify(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \
#endif /* __CONFIG_H */