diff --git a/CHANGELOG b/CHANGELOG index d5eae562ac..2bfaff60f6 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -1,3 +1,1665 @@ +commit 7754f33c6fb7a2c050388d20bf3847038558bdcf +Author: Larry Johnson +Date: Thu Feb 21 13:58:11 2008 -0500 + + LM73 bug fix for negative temperatures and cleanup + + When the LM73 temperature sensor measures a temperature below 0 C, the + current driver does not perform sign extension, so the result returned is + 512 C too high. This patch fixes the problem, and does general cleanup + of the code. + + Signed-off-by: Larry Johnson + +commit 96ef831f713289afba19da0c8f905e99da2b23e0 +Author: Guennadi Liakhovetski +Date: Thu Apr 3 13:36:02 2008 +0200 + + cfi_flash: Support buffered writes on non-standard Spansion NOR flash + + Some NOR flash chip from Spansion, for example, the s29ws-n MirrorBit + series require different addresses for buffered write commands. Define a + configuration option to support buffered writes on those chips. A more + elegant solution would be to automatically detect those chips by parsing + their CFI records, but that would require introduction of a fixup table + into the cfi_flash driver. + + Signed-off-by: Guennadi Liakhovetski + +commit 3f9c542d3d69b1a10a5e193e779133a0454d1f44 +Author: Lee Nipper +Date: Thu Apr 10 09:35:06 2008 -0500 + + mpc83xx: Update DIMM data bus width test to support 40-bit width + + 32-bit wide ECC memory modules report 40-bit width. + Changed the DIMM data bus width test to 'less than 64' instead of 'equal 32'. + + Signed-off-by: Lee Nipper + Signed-off-by: Kim Phillips + +commit 5fb5a689d822ca61e814bd523fc930af335242fa +Author: Dave Liu +Date: Mon Mar 31 17:05:12 2008 +0800 + + mpc83xx: Fix the bug of serdes initialization + + Currently the serdes will not be initializated due to the + partid's error. + + Signed-off-by: Dave Liu + Signed-off-by: Kim Phillips + +commit 2000784818f043db7ca60e2846a72d097766b894 +Author: Dave Liu +Date: Thu Apr 3 16:28:29 2008 +0800 + + mpc83xx: Fix the SATA clock setting of 837x targets + + Currently the SATA controller clock is configured as CSB clock, + usually the CSB clock is 400/333/266MHz. + + However, The SATA IP block is only guaranteed to operate up to + 200 MHz as stated in the HW spec. + + The bug is reported by Joe D'Abbraccio + + This patch makes the SATA clock as half of CSB clock. + + Signed-off-by: Dave Liu + Signed-off-by: Kim Phillips + +commit 1ac4f320bf0b593aa0a741f2d649a8ece8838672 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Apr 2 13:41:21 2008 +0200 + + mpc837xerdb: Fix warning: implicit declaration of function 'fdt_fixup_dr_usb' + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + Signed-off-by: Kim Phillips + +commit 97b3ecb575a92fa34c1765229dbc06f2b662f139 +Author: Kumar Gala +Date: Wed Apr 9 04:20:57 2008 -0500 + + 85xx: Fix detection of MP cpu spin up + + We were looking at the wrong memory offset to determine of a secondary + cpu had been spun up or not. Also added a warning message if the + all the secondary cpus we expect don't spin up. + + Signed-off-by: Kumar Gala + +commit f3e04bdc3f360c66801a9048956e61e41a16edba +Author: Kumar Gala +Date: Tue Apr 8 10:45:50 2008 -0500 + + 85xx: Use SVR_SOC_VER instead of SVR_VER + + The recent change introduced by 'Update SVR numbers to expand support' + now requires that we use SVR_SOC_VER instead of SVR_VER if we want + to compare against a particular processor id. + + Signed-off-by: Kumar Gala + +commit 5b2052e5f5fcce5dbd4d2750a29c0e45bce806e7 +Author: Eugene O'Brien +Date: Fri Apr 11 10:00:35 2008 -0400 + + ppc4xx: Fix power mgt definitions for PPC440 + + Corrected DCR addresses of PPC440EP power management registers. + + Signed-off-by: Eugene O'Brien + +commit 950a392464e616b4590bc4501be46e2d7d162dea +Author: Wolfgang Denk +Date: Fri Apr 11 15:11:26 2008 +0200 + + Revert merge of git://www.denx.de/git/u-boot-arm, commit 62479b18: + + Reverting became necessary after it turned out that the patches in + the u-boot-arm repo were modified, and in some cases corrupted. + + This reverts the following commits: + + 066bebd6353e33af3adefc3404560871699e9961 + 7a837b7310166ae8fc8b8d66d7ef01b60a80f9d6 + c88ae20580b2b01487b4cdcc8b2a113f551aee36 + a147e56f03871bba4f05058d5e04ce7deb010b04 + d6674e0e2a6a1f033945f78838566210d3f28c95 + 8c8463cce44d849e37744749b32d38e1dfb12e50 + c98b47ad24b2d91f41c09a3d62d7f70ad84f4b7d + 8bf69d81782619187933a605f1a95ee1d069478d + 8c16cb0d3b971f46fbe77c072664c0f2dcd4471d + a574a73852a527779234e73e17e7597fd8128882 + 1377b5583a48021d983e1fd565f7d40c89e84d63 + 1704dc20917b4f71e373e2c888497ee666d40380 + + Signed-off-by: Wolfgang Denk + +commit 64e541f4c1b413dd84c7e409f5c2bf328db2ac13 +Author: Stefan Roese +Date: Fri Apr 11 07:02:29 2008 +0200 + + ppc4xx: Update Kilauea defconfig to use device-tree booting as default + + This patch reworks the default environment on Kilauea/Haleakala. Now + "net_nfs" for exmaple uses the device-tree style booting formerly know + as "net_nfs_fdt". Also the addresses in RAM were changed because of the + new image booting support, which check for image overwriting. So the + addresses needed togeet adjusted. + + Signed-off-by: Stefan Roese + +commit 756f5dacda3810b094b94bcceffd3ce6c7ff9a28 +Author: Stefan Roese +Date: Wed Apr 9 11:58:02 2008 +0200 + + ppc4xx: Fix Canyonlands default environment to work with new image support + + Since the new image support checks for image overwriting, the default + environment needs to get adjusted to use correct addresses. + + Signed-off-by: Stefan Roese + +commit dfc6c7b647dba7ab86749616f0e9e5740deed422 +Author: Stefan Roese +Date: Wed Apr 9 11:54:11 2008 +0200 + + ppc: Revert patch 70431e8a that used _start instead of CFG_MONITOR_BASE + + The patch 70431e8a7393b6b793f77957f95b999fc9a269b8 (Make MPC83xx one step + closer to full relocation.) doesn't use CFG_MONITOR_BASE anymore. But + on 4xx systems _start currently cannot be used for this calculation. + So revert back to the original version for now. + + Signed-off-by: Stefan Roese + +commit f91374f65eae8b42cac329e06ba1c54728278efb +Author: Michal Simek +Date: Fri Mar 28 12:49:52 2008 +0100 + + microblaze: Sort microblaze boards in MAKEALL script + +commit 62032deb7214c6d9b4396297e2aaa559bc2f8495 +Author: Michal Simek +Date: Fri Mar 28 11:58:45 2008 +0100 + + microblaze: clean microblaze_config.mk + + FLAGS are generated by U-BOOT generator. + Board specific FLAGS are in board directory + + Signed-off-by: Michal Simek + +commit cf5c679ca04a6b54bf53a55b8b9c29335b387287 +Author: Michal Simek +Date: Fri Mar 28 12:47:19 2008 +0100 + + microblaze: xupv2p fix config file for supporting FDT + +commit 188dc16b189143573b1ed90e584bf866d75cdd12 +Author: Michal Simek +Date: Fri Mar 28 11:53:02 2008 +0100 + + microblaze: ml401 fix config file for supporting FDT + + Signed-off-by: Michal Simek + +commit 4c6a6f02e239236261333759997eeaf86b30b54c +Author: Michal Simek +Date: Fri Mar 28 11:22:48 2008 +0100 + + microblaze: ml401 - add ifdef for GPIO + + Signed-off-by: Michal Simek + +commit af7ae1a411c67ee9d17a66d17ce50b374f3dd4e7 +Author: Michal Simek +Date: Fri Mar 28 12:13:03 2008 +0100 + + microblaze: clean uart16550 and uartlite handling + + Signed-off-by: Michal Simek + +commit 0b20f250877441460fb79d72192954abe8498834 +Author: Michal Simek +Date: Fri Mar 28 11:08:31 2008 +0100 + + microblaze: Add Emaclite driver to Makefile + + Signed-off-by: Michal Simek + +commit 868cde5310f88234b774878e4f06e79df10a88b3 +Author: Michal Simek +Date: Fri Mar 28 11:08:01 2008 +0100 + + microblaze: Add Emac driver to Makefile + + Signed-off-by: Michal Simek + +commit 6f961b4f461f6cbb83a467d468a02e6078c2b327 +Author: Michal Simek +Date: Fri Mar 28 12:42:29 2008 +0100 + + microblaze: add Emac ethernet driver + +commit 89c53891b18cbafd29ab8931b40e27ad231b6085 +Author: Michal Simek +Date: Fri Mar 28 12:41:56 2008 +0100 + + microblaze: add Emaclite ethernet driver + +commit e5845e21224dbe2fe47b11f1cdf95de7f84be7cb +Author: Michal Simek +Date: Fri Mar 28 11:04:01 2008 +0100 + + microblaze: ML401 and XUPV2P remove emac and emaclite reference + + Signed-off-by: Michal Simek + +commit 6bf3e982aefdb1daf9f5462d482c8f9d1cc90a57 +Author: Michal Simek +Date: Fri Mar 28 10:59:32 2008 +0100 + + microblaze: remove old setting for emac driver + + Signed-off-by: Michal Simek + +commit cd2b75efb9cc037c74ecee9b3586f9bf9e1d4e57 +Author: Michal Simek +Date: Fri Mar 28 10:58:15 2008 +0100 + + microblaze: Clean Makefile from ancient emac driver + + Signed-off-by: Michal Simek + +commit ab68f921d9c741830f721c3d879c13a0c5597183 +Author: Daniel Hellstrom +Date: Fri Mar 28 10:20:43 2008 +0100 + + SPARC/LEON2: added support for Gaisler simulator GRSIM/TSIM for SPARC/LEON2 targets. See www.gaisler.com for information. + + Signed-off-by: Daniel Hellstrom + +commit 6ed8a43a19bb0275501bc286007daafa923552cf +Author: Daniel Hellstrom +Date: Wed Mar 26 23:38:48 2008 +0100 + + SPARC/LEON3: added support for GR-CPCI-AX2000 FPGA AX board. The FPGA is exchangeable but a standard LEON3 design is assumed. See www.gaisler.com for information. + + Signed-off-by: Daniel Hellstrom + +commit 6940383d9ec1bfe2f13e339e6f723e8d34af2b12 +Author: Daniel Hellstrom +Date: Wed Mar 26 23:34:47 2008 +0100 + + SPARC/LEON3: added support for Altera NIOS Development kit (STRATIX II Edition) with GRLIB template design. See www.gaisler.com for information. + + Signed-off-by: Daniel Hellstrom + +commit 823edd8a66ed50af5aaba0c79567f67061e4d79a +Author: Daniel Hellstrom +Date: Fri Mar 28 10:06:52 2008 +0100 + + SPARC/LEON3: added support for Gaisler GRSIM/TSIM2 SPARC/LEON3 simulatorn. See www.gaisler.com for information. + + Signed-off-by: Daniel Hellstrom + +commit 71d7e4c0489e5ed8fc69382236aaa2a1e510c135 +Author: Daniel Hellstrom +Date: Wed Mar 26 23:26:48 2008 +0100 + + SPARC/LEON3: added support for GR-XC3S-1500 board with GRLIB template design. See www.gaisler.com for board information. + + Signed-off-by: Daniel Hellstrom + +commit b330990c2f36ee4a8bb318360e1c8ba965269ab6 +Author: Daniel Hellstrom +Date: Fri Mar 28 10:00:33 2008 +0100 + + SPARC: Added support for SPARC LEON2 SOC Processor. + + Signed-off-by: Daniel Hellstrom + +commit 2a2fa797e63b1e3cd4d570318ca5fbf8723ef53a +Author: Daniel Hellstrom +Date: Wed Mar 26 23:00:38 2008 +0100 + + SPARC/LEON3: Added AMBA Bus Plug&Play information print command (ambapp). It can print available cores (type: AHB Master, AHB Slave, APB Slave), their address ranges, IRQ number and version. + + Signed-off-by: Daniel Hellstrom + +commit 1e9a164e22976933002c5e4b0b79b09fcede9cd4 +Author: Daniel Hellstrom +Date: Wed Mar 26 22:51:29 2008 +0100 + + SPARC: Added support for SPARC LEON3 SOC processor. + + Signed-off-by: Daniel Hellstrom + +commit bf3d8b31169546fcddb4737391e1893fb12d033a +Author: Daniel Hellstrom +Date: Fri Mar 28 08:29:26 2008 +0100 + + SPARC: added SPARC support for new uimage in common code. + + Signed-off-by: Daniel Hellstrom + +commit 00ab32c85405a4fe65fd4128243086210fc90a21 +Author: Daniel Hellstrom +Date: Wed Mar 26 22:36:03 2008 +0100 + + SPARC: added SPARC board information to the command bdinfo. + + Signed-off-by: Daniel Hellstrom + +commit c2f02da21a3f37f0878554eebc785e04fdc4e128 +Author: Daniel Hellstrom +Date: Fri Mar 28 09:47:00 2008 +0100 + + SPARC: Added generic support for SPARC architecture. + + Signed-off-by: Daniel Hellstrom + +commit e54ec0f016803e4d9524ff71f7971bda0c51b287 +Author: Stefan Roese +Date: Thu Apr 3 14:50:34 2008 +0200 + + ppc4xx: Fix 4xx enet driver to support 460GT EMAC2+3 + + This patch fixes a problem with the RGMII setup of the 460GT. The 460GT + has 2 RGMII instances and we need to configure the 2nd RGMII instance + for the EMAC2+3 channels. + + Signed-off-by: Stefan Roese + +commit c2a545ce33b26d80337f80b533828839249fb1c9 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Wed Apr 2 08:03:56 2008 +0200 + + MPC8xx: Fix libfdt support introduced in commit 77ff7b74 + + fdt.c: In function 'ft_cpu_setup': + fdt.c:33: warning: implicit declaration of function 'do_fixup_by_prop_u32' + fdt.c:39: warning: implicit declaration of function 'do_fixup_by_compat_u32' + fdt.c:43: warning: implicit declaration of function 'fdt_fixup_ethernet' + fdt.c:45: warning: implicit declaration of function 'fdt_fixup_memory' + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 4abd844d8eb108736e1cf8fbf3dbf61f2d5fc11b +Author: Andy Fleming +Date: Mon Mar 31 20:45:56 2008 -0500 + + Fix fdt set command to conform to dts spec + + The fdt set command was treating properties specified as <00> and <0011> + as byte streams, rather than as an array of cells. As we already have + syntax for expressing the desire for a stream of bytes ([ xx xx ...]), + we should use the <> syntax to describe arrays of cells, which are always + 32-bits per element. If we imagine this likely (IMHO) scenario: + + > fdt set /ethernet-phy@1 reg <1> + + With the old code, this would create a bad fdt, since the reg cell would be + made to be one byte in length. But the cell must be 4 bytes, so this would + break mysteriously. + + Also, the dts spec calls for constants inside the angle brackets (<>) + to conform to C constant standards as they pertain to base. + Take this scenario: + + > fdt set /ethernet@f00 reg <0xe250000\ 0x1000> + + The old fdt command would complain that it couldn't parse that. Or, if you + wanted to specify that a certain clock ran at 33 MHz, you'd be required to + do this: + + > fdt set /mydev clock <1f78a40> + + Whereas the new code will accept decimal numbers. + + While I was in there, I extended the fdt command parser to handle property + strings which are split across multiple arguments: + + > fdt set /ethernet@f00 interrupts < 33 2 34 2 36 2 > + > fdt p /ethernet@f00 + ethernet@f00 { + interrupts = <0x21 0x2 0x22 0x2 0x24 0x2>; + }; + + Lastly, the fdt print code was rearranged slightly to print arrays of cells + if the length of the property is a multiple of 4 bytes, and to not print + leading zeros. + + Signed-off-by: Andy Fleming + +commit 1c2926abdd7db89296a8cc7f224dd9d5d4e37a56 +Author: Stefan Roese +Date: Wed Apr 2 08:39:33 2008 +0200 + + ppc4xx: Canyonlands: Init SATA/PCIe port correctly + + Canyonlands (460EX) shares the first PCIe interface with the SoC SATA + interface. This usage can be configured with the jumper J6. This patch + correctly configures the SATA/PCIe PHY for SATA usage when this jumper + is installed. + + Signed-off-by: Stefan Roese + +commit 6fe2946f198481254a6ee9600d7456b8316a4083 +Author: Kim Phillips +Date: Fri Mar 28 17:37:49 2008 -0500 + + remove remaining CONFIG_OF_HAS_{UBOOT_ENV,BD_T} code + + finish off what commit 43ddd9c820fec44816188f53346b464e20b3142d, + "Remove deprecated CONFIG_OF_HAS_UBOOT_ENV and CONFIG_OF_HAS_BD_T" + started. + + Signed-off-by: Kim Phillips + +commit b5873f1732b92a25690e1513b90dfb0d644f6697 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Tue Apr 1 07:30:51 2008 +0200 + + dataflash: Move CONFIG_HAS_DATAFLASH to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 2d934ea51f276522b532f870a820e844ff480b5b +Author: Tor Krill +Date: Fri Mar 28 15:29:45 2008 +0100 + + Add Vitesse 8601 support to TSEC driver + + Add phy_info for Vitesse VSC8601. + Add config option, CFG_VSC8601_SKEWFIX, to enable RGMII skew timing compensation. + + Signed-off-by: Tor Krill + Reviewed-by: Kim Phillips + Signed-off-by: Ben Warren + +commit 3eac6402a508b0f68a21cc9cbc2cc49347de0c31 +Author: Daniel Hellstrom +Date: Mon Mar 31 14:25:00 2008 +0000 + + SPARC: added SMC91111 driver in and out macros for LEON processors. + + This patch makes SPARC/LEON processors able to read and write + to the SMC91111 chip using the chip external I/O bus of the memory + controller. This patchs defines the standard in and out macros + expected by the SMC9111 driver. + + To access that I/O bus one must set up the memory controller + (MCTRL or FTMCTRL) correctly. It is assumed that the user sets + up this correctly when the other MCTRL parameters are set up. It + can be set up from the board configuration header file. + + Signed-off-by: Daniel Hellstrom + Signed-off-by: Ben Warren + +commit 3ca7c558eba36332556bc470d45e2f5d42bd0ca6 +Author: Stelian Pop +Date: Wed Mar 26 18:52:34 2008 +0100 + + Add maintainership information for AT91CAP9ADK and AT91SAM9260EK boards + + Signed-off-by: Stelian Pop + +commit 4e03dde84dd2c91e327cdc23ae119d432559a7a3 +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Mar 31 21:31:04 2008 +0200 + + AT91SAM9260EK: Move CONFIG_CMD_NAND to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 0176d43e759a6e00cacc85eff26fd60f74b4f6b7 +Author: Stelian Pop +Date: Wed Mar 26 18:52:33 2008 +0100 + + Add support for AT91SAM9260EK + + Support for booting from internal DataFlash, external DataFlash card + or NAND flash is available. + + Signed-off-by: Stelian Pop + +commit 1762f13b4aab88b685b1722f17dada247945624b +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Mar 31 21:20:49 2008 +0200 + + AT91SAM9: Move CONFIG_HAS_DATAFLASH to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 761712188b353494defb2b644491ff73d0daaa6f +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Mon Mar 31 21:12:17 2008 +0200 + + AT91CAP9ADK: Move CONFIG_CMD_NAND to Makefile + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 983c1db04c1dd0f92e02f06d29f0c65a3d9a2687 +Author: Stelian Pop +Date: Wed Mar 26 20:52:32 2008 +0100 + + Port AT91CAP9 to the new headers + + Adapt the existing AT91CAP9 code to the new headers and APIs. + + Signed-off-by: Stelian Pop + +commit 177e8a5ac81bbc531a1d54abdb47f2860266c3aa +Author: Stelian Pop +Date: Wed Mar 26 19:52:31 2008 +0100 + + Finish header files reworking + + Replace AT91CAP9.h file with several splitted header files coming + from the Linux kernel. + + This is part 2 of the replacement: more header imports and edits. + + Signed-off-by: Stelian Pop + +commit 6d1dbbbf9fdf727384002e553e615c15d8b967f4 +Author: Stelian Pop +Date: Wed Mar 26 19:52:30 2008 +0100 + + Import several header files from Linux + + Replace AT91CAP9.h file with several splitted header files coming + from the Linux kernel. + + This is part 1 of the replacement: pristine header files import. + + Signed-off-by: Stelian Pop + +commit a8a78f2d99dc1bd30dc3595da118539b506c6118 +Author: Stelian Pop +Date: Wed Mar 26 20:52:28 2008 +0100 + + Move at91cap9 specific files to at91sam9 directory + + AT91CAP9 and AT91SAM9 SoCs are very close hardware wise, so a + common infrastructure can be used. Let this infrastructure be + named after the AT91SAM9 family, and move the existing AT91CAP9 + files to the new place. + + Signed-off-by: Stelian Pop + +commit 61106a565870ff503f92b251b94bd7afef889a04 +Author: Stelian Pop +Date: Wed Mar 26 21:52:27 2008 +0100 + + Use timer_init() instead of board supplied interrupt_init() + + The timer on AT91CAP9/AT91SAM9 is supplied by the SoC, and not by + the board, so use timer_init() instead of interrupt_init(). + + Signed-off-by: Stelian Pop + +commit 5604e2178c5218fbfdba2e4293ca7652e829ac25 +Author: Stelian Pop +Date: Wed Mar 26 21:52:36 2008 +0100 + + Cleanup DataFlash partition handling + + DataFlash partition information has become a mess. This patch + defines a single partition scheme for Atmel DataFlashes. This partition + scheme will be used by all AT91CAP9 and AT91SAM9 boards. + + Signed-off-by: Stelian Pop + +commit 9b46432fc65ce0f0826b32e4f15c15b33ccb8d42 +Author: TsiChung Liew +Date: Fri Mar 28 08:47:45 2008 -0500 + + ColdFire: Fix alignment issue after CONFIG_IDENT_STRING in start.S + + When the version_string function in start.S is not 4-byte align, + it will cause the compiler generates "unaligned opcodes detected + in executable segment". This issue affects all ColdFire CPUs. + By adding .align 4 after CONFIG_IDENT_STRING, it will pad 0's if + it is not aligned. + + Signed-off-by: TsiChung Liew + Acked-by: John Rigby + +commit bae61eefe15b4d454060a7140e49ae58322be803 +Author: TsiChung Liew +Date: Tue Mar 25 15:41:15 2008 -0500 + + ColdFire: Add dspi and serial flash support for MCF5445x + + Signed-off-by: TsiChung Liew + Acked-by: John Rigby + +commit 48ead7a7a922fceaf494e352abfab8216a41b417 +Author: TsiChung Liew +Date: Tue Mar 18 17:37:01 2008 -0500 + + ColdFire: Remove R5200 board + + This board never went into production + + Signed-off-by: Zachary P. Landau + Acked-by: TsiChung Liew + Acked-by: John Rigby + +commit 545c8e0a7cd3ca9d3846668f69b0d201250abea8 +Author: Matthew Fettke <[matthew.fettke@gmail.com]> +Date: Thu Jan 24 14:02:32 2008 -0600 + + ColdFire: Added M5275EVB support. + + Signed-off-by: Matthew Fettke + Signed-off-by: TsiChung Liew + Acked-by: John Rigby + +commit f71d9d91a2cd9c30b2b6369f15c1a46c11537c2b +Author: Matthew Fettke <[matthew.fettke@gmail.com]> +Date: Mon Feb 4 15:38:20 2008 -0600 + + ColdFire: Added MCF5275 cpu support. + + Signed-off-by: Matthew Fettke + Signed-off-by: TsiChung Liew + Acked-by: John Rigby + +commit 44e5b9edab077aba6e9b849afa4b7fbd8fd7b02b +Author: TsiChung Liew +Date: Mon Mar 17 12:14:11 2008 -0500 + + ColdFire: Define bootdelay in configuration file for M52277EVB + + Signed-off-by: Matt Wadel + Acked-by: TsiChung Liew + Acked-by: John Rigby + +commit 77878f16cedee17161ff2336990970fffc6cea35 +Author: TsiChung Liew +Date: Mon Mar 17 12:09:07 2008 -0500 + + ColdFire: Fix second memory Chipselect for M5475EVB + + Signed-off-by: TsiChung Liew + Acked-by: John Rigby + +commit 43d60642395a550956cb21d287c8cfa563913d28 +Author: TsiChung Liew +Date: Thu Mar 13 14:26:32 2008 -0500 + + ColdFire: Update correct FLASHBAR and RAMBAR1 for MCF5282 + + Signed-off-by: TsiChung Liew + Acked-by: John Rigby + +commit eb14ebe813a0cb5d47905228da446a5ad692473b +Author: Larry Johnson +Date: Sun Mar 30 20:33:04 2008 -0500 + + ppc4xx: Add CFG_MEM_TOP_HIDE to Denali SPD-based SDRAM setup + + Signed-off-by: Larry Johnson + +commit 02e3892021112f21067d9ed1d04ae4182725ba52 +Author: Stefan Roese +Date: Mon Mar 31 12:20:48 2008 +0200 + + ppc4xx: Small whitespace fix of esd patches + + Signed-off-by: Stefan Roese + +commit 034394abb524785047c815f00dde8cdbdc1593c5 +Author: Matthias Fuchs +Date: Sun Mar 30 18:52:44 2008 +0200 + + ppc4xx: Cleanup PMC440 board support + + Signed-off-by: Matthias Fuchs + +commit a6cc6c37188d85c25d167a4515da86f48d9a583e +Author: Matthias Fuchs +Date: Sun Mar 30 18:52:06 2008 +0200 + + ppc4xx: Add ptm configuration variables for PMC440 + + Add support for the ptm1la, ptm1ms, ptm2la and ptm2ms + environment variables. + + Cleanup pci_target_init. + + Signed-off-by: Matthias Fuchs + +commit 7c91f51a2fe296909147f1646a1412729dd10b1d +Author: Matthias Fuchs +Date: Sun Mar 30 18:01:15 2008 +0200 + + ppc4xx: Minor updates for DU440 boards + + Signed-off-by: Matthias Fuchs + +commit d5bffeb868d6b4d462f558dac43011027b6644b7 +Author: Mike Frysinger +Date: Tue Feb 19 00:54:20 2008 -0500 + + Blackfin: cleanup and overhaul common board init functions + + Signed-off-by: Mike Frysinger + +commit b86b3416f874358acaf07519e7620cdb2145f75b +Author: Mike Frysinger +Date: Tue Feb 19 00:50:58 2008 -0500 + + Blackfin: cleanup lib_blackfin/cache.c + + Signed-off-by: Mike Frysinger + +commit 9171fc81722c20fdb5a829a58b17c9eaadd5fb44 +Author: Mike Frysinger +Date: Sun Mar 30 15:46:13 2008 -0400 + + Blackfin: unify cpu and boot modes + + All of the duplicated code for Blackfin processors and boot modes have been + unified. After all, the core is the same for all processors, just the + peripheral set differs (which gets handled in the drivers). + + Signed-off-by: Mike Frysinger + +commit 880cc4381ea8360248cddcdf87a64566745a5724 +Author: Stelian Pop +Date: Wed Mar 26 22:52:35 2008 +0100 + + Fix CFG_NO_FLASH compilation. + + Many Atmel boards have no "real" (NOR) flash on board, and rely only + on DataFlash and NAND memories. This patch enables CFG_NO_FLASH to + be present in a board configuration file, while still enabling flash + commands like 'flinfo', 'protect', etc. + + Signed-off-by: Stelian Pop + +commit 9ce7e53abd039decea1af67aec81bbd5df7a2593 +Author: Mike Frysinger +Date: Tue Feb 19 00:58:13 2008 -0500 + + Blackfin: BF537-stamp: cleanup spi flash driver + + This punts the old spi flash driver for a new/generalized one until the + common one can be integrated. + + Signed-off-by: Mike Frysinger + +commit bb8e3cf25bc0b04936c0c1a075985dd8700a244b +Author: Ben Warren +Date: Sun Mar 30 11:34:34 2008 -0400 + + Fix macro typo in common/cmd_mii.c + + This typo was introduced in commit 233a8bcd94997f3f345833a3b82e836222f2a206. I + actually applied the wrong patch. + + Signed-off-by: Ben Warren + +commit f1b985f2d724ccaa4d3def07917f0caaf18fa77d +Author: Jean-Christophe PLAGNIOL-VILLARD +Date: Sun Mar 30 16:39:53 2008 +0200 + + use correct at91rm9200 register name in m501sk board + + This fixes a naming bug for at91rm9200 lowlevel init code: + NOR boot flash is on chipselect 0, not chipselect 2. This + makes code use the register name from chip datasheets. + + Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD + +commit 480ed1dea103a1c8f4591afc77d2de3c7868d983 +Author: David Brownell +Date: Fri Jan 18 12:55:00 2008 -0800 + + use correct at91rm9200 register name + + This fixes a naming bug for at91rm9200 lowlevel init code: + NOR boot flash is on chipselect 0, not chipselect 2. This + makes code use the register name from chip datasheets. + + Signed-off-by: David Brownell + +commit a3543d6dc52b0ba9c64016687cf32d600b31a476 +Author: David Brownell +Date: Fri Jan 18 12:45:45 2008 -0800 + + add missing ARM boards to MAKEALL + + Add some missing ARM boards to MAKEALL. These build correctly, + unlike several of the boards already listed. + + Signed-off-by: David Brownell + +commit 066bebd6353e33af3adefc3404560871699e9961 +Author: Peter Pearse +Date: Sun Mar 30 11:34:09 2008 +0100 + + Bracket READ_TIMER macro in cpu/arm1136/omap24xx/interrupts.c + to prevent compilation error. + + Signed-off-by: Peter Pearse + +commit 7a837b7310166ae8fc8b8d66d7ef01b60a80f9d6 +Author: Guennadi Liakhovetski <[lg@denx.de]> +Date: Sun Mar 30 11:32:30 2008 +0100 + + Support for the MX31ADS evaluation board from Freescale + + This patch adds support for the MX31ADS evaluation board from Freescale, + initialization code is copied from RedBoot sources, also provided by Freescale. + + Signed-off-by: Guennadi Liakhovetski + +commit c88ae20580b2b01487b4cdcc8b2a113f551aee36 +Author: Sascha Hauer +Date: Sun Mar 30 11:32:27 2008 +0100 + + Phytec Phycore-i.MX31 support + + This patch adds support for the Phytec Phycore-i.MX31 board + + Signed-off-by: Sascha Hauer + Signed-off-by: Guennadi Liakhovetski + +commit a147e56f03871bba4f05058d5e04ce7deb010b04 +Author: Sascha Hauer +Date: Sun Mar 30 11:32:24 2008 +0100 + + mx31 litekit support + + This patch adds support for the mx31 litekit board + + Signed-off-by: Sascha Hauer + Signed-off-by: Guennadi Liakhovetski + +commit d6674e0e2a6a1f033945f78838566210d3f28c95 +Author: Sascha Hauer +Date: Sun Mar 30 11:32:21 2008 +0100 + + add SMSC LAN9x1x Network driver + + This patch adds a driver for the following smsc network controllers: + LAN9115 + LAN9116 + LAN9117 + LAN9215 + LAN9216 + LAN9217 + + Signed-off-by: Sascha Hauer + Signed-off-by: Guennadi Liakhovetski + +commit 8c8463cce44d849e37744749b32d38e1dfb12e50 +Author: Sascha Hauer +Date: Sun Mar 30 11:32:16 2008 +0100 + + add an i2c driver for mx31 + + This patch adds an i2c driver for Freescale i.MX processors + + Signed-off-by: Sascha Hauer + Signed-off-by: Guennadi Liakhovetski + +commit c98b47ad24b2d91f41c09a3d62d7f70ad84f4b7d +Author: Sascha Hauer +Date: Sun Mar 30 11:30:43 2008 +0100 + + core support for Freescale mx31 + + This patch adds the core support for Freescale mx31 + + Signed-off-by: Sascha Hauer + Signed-off-by: Guennadi Liakhovetski + +commit 8bf69d81782619187933a605f1a95ee1d069478d +Author: Sascha Hauer +Date: Sun Mar 30 11:28:46 2008 +0100 + + Separate omap24xx specific code from arm1136 + + Move omap24xx code to cpu/arm1136/omap24xx, rename include/asm-arm/arch-arm1136 to cpu/arm1136/omap24xx. + + Signed-off-by: Sascha Hauer + Signed-off-by: Guennadi Liakhovetski + +commit 8c16cb0d3b971f46fbe77c072664c0f2dcd4471d +Author: Peter Pearse +Date: Sun Mar 30 11:23:05 2008 +0100 + + Add pmdra into MAKEALL + + Signed-off-by: Peter Pearse + +commit a574a73852a527779234e73e17e7597fd8128882 +Author: Pieter Voorthuijsen <[pieter.voorthuijsen@Prodrive.nl]> +Date: Sun Mar 30 11:21:58 2008 +0100 + + Adds support for the Prodrive PMDRA board, based on a DM6441 + + Signed-off-by: Pieter Voorthuijsen + +commit 1377b5583a48021d983e1fd565f7d40c89e84d63 +Author: Pieter Voorthuijsen <[pieter.voorthuijsen@Prodrive.nl]> +Date: Sun Mar 30 11:11:34 2008 +0100 + + Removes all board specific code from the arch. part for DM644x (DaVinci) boards + + Signed-off-by: Pieter Voorthuijsen + +commit 1704dc20917b4f71e373e2c888497ee666d40380 +Author: Dirk Behme +Date: Sun Mar 30 11:09:01 2008 +0100 + + - Remove *_masked() functions as noted by Wolfgang + - Adapt register naming to recent TI spec (sprue26, March 2007) + - Fix reset_timer() handling + - As reported by Pieter [1] the overflow fix introduced a + delay of factor 16 (e.g 2 seconds became 32). While the + overflow fix is basically okay, it missed to divide udelay by + 16, too. Fix this. + [1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/38179 + - Remove software division of timer count value (DIV(x) + macro) and do it in hardware (TIM_CLK_DIV). + Many thanks to Troy Kisky + and Pieter Voorthuijsen for + the hints & testing! + + Signed-off-by: Dirk Behme + + Acked-by: Pieter Voorthuijsen + +commit ac3315c26e143c31680750c9c13f027efbcc887e +Author: Andre Schwarz +Date: Thu Mar 6 16:45:44 2008 +0100 + + new PHY @ e1000 - 2nd try + + Add 82541ER device with latest integrated IGP2 PHY. + Introduced CONFIG_E1000_FALLBACK_MAC for NIC bring-up with empty eeprom. + + Signed-off-by: Andre Schwarz + Signed-off-by: Ben Warren + +commit c2b7da552293b50c9c9e46ed71267b02c2de9ea8 +Author: Daniel Hellstrom +Date: Fri Mar 28 20:22:53 2008 +0100 + + SPARC/LEON3: Added GRETH Ethernet 10/100/1000 driver. + + GRETH is an Ethernet 10/100 or 10/100/1000 MAC with out without + a debug link (EDCL). The GRETH core is documented in GRIP.pdf + available at www.gaisler.com. + + If the GRETH has GigaBit support (GBIT, Scatter gather, checksum + offloading etc.) can be determined by a bit in the control register. + The GBIT MAC is supported by operating in GRTEH 10/100 legacy mode. + + Signed-off-by: Daniel Hellstrom + Signed-off-by: Ben Warren + +commit 233a8bcd94997f3f345833a3b82e836222f2a206 +Author: Tsi-Chung Liew +Date: Mon Mar 17 17:08:22 2008 -0500 + + Add CONFIG_MII_INIT in cmd_mii.c + + Provide common configuration in do_mii() to execute mii_init() + for all cpu architectures + + Signed-off-by: TsiChung Liew + Signed-off-by: Ben Warren + +commit f605479de2deb11e834f31dfdb0af107c86aced6 +Author: Tsi-Chung Liew +Date: Mon Mar 17 17:08:16 2008 -0500 + + ColdFire: Fix FEC transmit issue for MCF5275 + + Signed-off-by: TsiChung Liew + Signed-off-by: Ben Warren + +commit d9a2f416d6ac6058cd7845033ae4dc32ef1c0746 +Author: Aras Vaichas +Date: Wed Mar 26 09:43:57 2008 +1100 + + DHCP request fix for Windows Server 2003 + + Added option CONFIG_BOOTP_DHCP_REQUEST_DELAY. This provides an optional + delay before sending "DHCP Request" in net/bootp.c. Required to overcome + interoperability problems with Windows Server 200x DHCP server when U-Boot + client responds too fast for server to handle. + + Signed-off-by: Aras Vaichas + Signed-off-by: Ben Warren + +commit 97bf85d784fbed485e652eb907589ad0d5cb7262 +Author: Daniel Hellstrom +Date: Fri Mar 28 20:40:19 2008 +0100 + + MTD/CFI: flash_read64 is defined a weak function (for SPARC) + + SPARC has implemented __raw_readq, it reads 64-bit from any 32-bit address. + SPARC CPUs implement flash_read64 which calls __raw_readq. + + For current SPARC architectures (LEON2 and LEON3) each read from the + FLASH must lead to a cache miss. This is because FLASH can not be set + non-cacheable since program code resides there, and alternatively disabling + cache is poor from performance view, or doing a cache flush between each + read is even poorer. + + Forcing a cache miss on a SPARC is done by a special instruction "lda" - + load alternative space, the alternative space number (ASI) is processor + implementation spcific and can be found by including . + + Signed-off-by: Daniel Hellstrom + +commit 70431e8a7393b6b793f77957f95b999fc9a269b8 +Author: Joakim Tjernlund +Date: Fri Mar 28 15:41:25 2008 +0100 + + Make MPC83xx one step closer to full relocation. + + Remove a few absolute references to CFG_MONITOR_BASE for ppc/mpc83xx + and use GOT relative reference. + + Signed-off-by: Joakim Tjernlund + Signed-off-by: Kim Phillips + +commit 5b2793a3f3de34d439232b05acc8af67a028fd35 +Author: Michael Barkowski +Date: Thu Mar 27 14:34:43 2008 -0400 + + mpc8323erdb: fix EEPROM page size and get MAC from EEPROM + + This patch fixes eeprom page size so that you can now write more than + 64 bytes at a time. + + It also makes the board take MAC addresses, if found, from EEPROM. + + User should place up to 4 addresses at offset 0x7f00, for + eth{,1,2,3}addr. Any unused addresses should be zero. This group of + four six-byte values should have it's CRC at the end. crc32 and + eeprom commands can be used to accomplish this. + + If CRC fails, MAC addresses come from the environment. If CRC + succeeds, the environment is overwritten at startup. + + Signed-off-by: Michael Barkowski + Signed-off-by: Kim Phillips + +commit 8f325cff31f6e745e6540014b131b9a97f61944c +Author: Michael Barkowski +Date: Fri Mar 28 15:15:38 2008 -0400 + + mpc8323erdb: define CONFIG_PCI_SKIP_HOST_BRIDGE + + Commit 55774b512fdf63c0516d441cc5da7c54bbffb7f2 broke the onboard USB + controller on the PCI bus in Linux on the MPC8323ERDB. + + This fixes it by defining CONFIG_PCI_SKIP_HOST_BRIDGE in the board's + config file. + + Signed-off-by: Michael Barkowski + Signed-off-by: Kim Phillips + +commit e5c4ade4db1e16d3e5d4a7887f34e10e516ed3a9 +Author: Kim Phillips +Date: Fri Mar 28 10:19:07 2008 -0500 + + mpc83xx: cleanup System Part and Revision ID Register (SPRIDR) code + + in the spirit of commit 1ced121600b2060ab2ff9f0fddd9421fd70a0dc6, + 85xx's "Update SVR numbers to expand support", simplify SPRIDR processing + and processor ID display. Add REVID_{MAJ,MIN}OR macros to make + REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR + convenience macros. + + Signed-off-by: Kim Phillips + +commit 81fd52c6c8fd19f0b7856b98217ce37c46c521af +Author: Kim Phillips +Date: Fri Mar 28 10:18:53 2008 -0500 + + mpc83xx: display ddr frequency in board_add_ram_info banner + + Signed-off-by: Kim Phillips + +commit 35cf155c5ec1ceab2849fa5b6aa3d9a3e9e6f482 +Author: Kim Phillips +Date: Fri Mar 28 10:18:40 2008 -0500 + + mpc83xx: unreinvent mem_clk + + delete ddr_clk and use mem_clk instead. Rename other ddr_*_clk to + mem_*_clk for consistency's sake. + + Signed-off-by: Kim Phillips + +commit 730e792926ca3fe4dd1b734a3bf44e55afa6f536 +Author: Kim Phillips +Date: Fri Mar 28 14:31:23 2008 -0500 + + mpc83xx: enable the SATA interface on mpc8315 rdb and mpc837x rdb boards + + Signed-off-by: Kim Phillips + +commit 2eeb3e4fc54ef2f5d574dafd42c6ce93afa30393 +Author: Dave Liu +Date: Wed Mar 26 22:57:19 2008 +0800 + + mpc83xx: enable the SATA interface on mpc837xemds board + + Enable the first two SATA interfaces on MPC837xEMDS board, + The two SATA ports are on LYNX1. (SATA0/1 on J4/5) + + Signed-off-by: Dave Liu + Signed-off-by: Kim Phillips + +commit 6f8c85e8d1865730c158d9ef5a06c70c3a10600a +Author: Dave Liu +Date: Wed Mar 26 22:56:36 2008 +0800 + + mpc83xx: initialize serdes for MPC837xEMDS boards + + This patch is stolen from Anton Vorontsov's patch + for mpc837xerdb boards. + + The reference clk and xcorevdd voltage of serdes1/2 + is same between mpc837xemds and mpc837xerdb. + + 8377E: LYNX1- 2 SATA LYNX2- 2 PCIE + 8378E: LYNX1- 2 SGMII LYNX2- 2 PCIE + 8379E: LYNX1- 2 SATA LYNX2- 2 SATA + + Signed-off-by: Dave Liu + Signed-off-by: Kim Phillips + +commit cc8e839abc80887ae832767b5930d40edd6d7eb7 +Author: Stefan Roese +Date: Fri Mar 28 14:09:04 2008 +0100 + + ppc4xx: Canyonlands: Print SATA/PCIe configuration and board revision + + Canyonlands (460EX) shares the first PCIe interface with the SoC SATA + interface. This usage can be configured with the jumper J6. This patch + displays the current configuration upon bootup and changes the PCIe + init loop, to only initialize the availabel PCIe slots. + + Signed-off-by: Stefan Roese + +commit 90447ecbbac8572457b6d8903073ac3f120995ba +Author: Tor Krill +Date: Fri Mar 28 11:29:10 2008 +0100 + + MTD/CFI: Add support for 16bit legacy AMD flash + + Add entry for 512Kx16 AMD flash to jedec_table. + Read out 16bit device id if chipwidth is 16bit. + Fixed coding style after Stefans feedback + + Signed-off-by: Tor Krill + +commit 5e12e75d17c4b15a310a45cd78fe71b7698a8a8e +Author: Stefan Roese +Date: Fri Mar 28 11:02:53 2008 +0100 + + ppc: Small change to CFG_MEM_TOP_HIDE description + + Signed-off-by: Stefan Roese + +commit 280df59a8d62c6e74c281b1cb7e2052df4d6cb00 +Author: Nobuhiro Iwamatsu +Date: Thu Mar 27 15:44:12 2008 +0900 + + sh: Add support stat structure and stat.h + + Signed-off-by: Nobuhiro Iwamatsu + +commit 4be9eb789e72b845d6693cc36b70a0b3529b3f09 +Author: Mark Jonas +Date: Sat Mar 22 19:27:52 2008 +0100 + + sh: Removed warning when compiling drivers/serial/serial_sh.c. + + Signed-off-by: Mark Jonas + Signed-off-by: Nobuhiro Iwamatsu + +commit f309fa38929ffba71230c02330ffa42f4bba6333 +Author: Nobuhiro Iwamatsu +Date: Wed Mar 12 18:02:57 2008 +0900 + + sh: Remove disable_ctrlc function from R7780MP + + Signed-off-by: Nobuhiro Iwamatsu + +commit 6f4b266ff2a4fcc2bff985d6a217852469afddb3 +Author: Nobuhiro Iwamatsu +Date: Wed Mar 12 17:55:15 2008 +0900 + + sh: Add maintainer of R7780MP to MAINTAINER file + + Update MAINTAINER entry for R7780MP. And fix maintainer's name. + + Signed-off-by: Nobuhiro Iwamatsu + +commit f5e2466f7baa887a7df0c536333eea8231333497 +Author: Nobuhiro Iwamatsu +Date: Tue Mar 25 17:11:24 2008 +0900 + + sh: Add support Renesas Solutions R2D plus board + + R2D plus is SH reference board used with SH7751R. + This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface, + one PCI bus, VGA, and two Ethernet controller. + + Signed-off-by: Nobuhiro Iwamatsu + +commit e92c95180bb5bc5fd4051598a9d60beaba48988d +Author: Nobuhiro Iwamatsu +Date: Wed Mar 12 12:15:29 2008 +0900 + + sh: Add support SH4 cache control + + Add support SH4 cache control and flash_cache function + + Signed-off-by: Nobuhiro Iwamatsu + +commit 28e5efde4d925fcb34901d0030d0648de2da7e89 +Author: Nobuhiro Iwamatsu +Date: Mon Mar 24 01:53:01 2008 +0900 + + sh: Add support PCI host driver for SH7751/SH7751R + + Signed-off-by: Nobuhiro Iwamatsu + +commit ab8f4d40d069cd3cbe7563ddfe3e5f03b0c7c721 +Author: Nobuhiro Iwamatsu +Date: Mon Mar 24 02:11:26 2008 +0900 + + sh: Move SuperH PCI driver from cpu/sh4 to drivers/pci + + Signed-off-by: Nobuhiro Iwamatsu + +commit 566933278101c144d75361ea682678a326c1290d +Author: Nobuhiro Iwamatsu +Date: Wed Mar 12 12:10:28 2008 +0900 + + sh: Add support SuperH SH7751/SH7751R + + Signed-off-by: Nobuhiro Iwamatsu + +commit 3313e0e26224fc9a0c445124f3455058c696df84 +Author: Mark Jonas +Date: Mon Mar 10 11:37:10 2008 +0100 + + sh: Added support for SH7720 based board MPR2. + + Signed-off-by: Mark Jonas + Signed-off-by: Nobuhiro Iwamatsu + +commit 3ecff1d70ae93e628fe65b3fe1fc7c9c76cdf99f +Author: Nobuhiro Iwamatsu +Date: Thu Mar 6 14:05:53 2008 +0900 + + sh: Fix receive FIFO level register of SH4A + + Receive FIFO level register is different in SH4A. + Because register is different, cannot occasionally receive data. + + Signed-off-by: Nobuhiro Iwamatsu + +commit c133c1fb0b590662206b0eba70f4478ee0300a9a +Author: Yusuke Goda +Date: Tue Mar 11 12:55:12 2008 +0900 + + sh: Add support Renesas Solutions R7780MP + + Renesas Solutions R7780MP is a reference board on SH7780. + This board has serial, 10/100 base Ethernet deivice, CF slot + and VGA devices. This board can set extension board. + Extension board has 10/100/1000 base Ethernet device, PCI slot, + S-ATA, iDVR slot. + + Signed-off-by: Yusuke Goda + Signed-off-by: Nobuhiro Iwamatsu + +commit 1a2334a4eb6386d7cd35d9de5fa39af2c764ad28 +Author: Yusuke Goda +Date: Wed Mar 5 14:30:02 2008 +0900 + + sh: Add support PCI of SuperH and SH7780 + + This patch add support PCI of SuperH base code and SH7780 specific code. + + Signed-off-by: Yusuke Goda + Signed-off-by: Nobuhiro Iwamatsu + +commit b55523efff2ae11f0b9ae3cc405893c32eb78156 +Author: Yusuke Goda +Date: Wed Mar 5 14:23:26 2008 +0900 + + sh: Add support SH7780 + + SH7780 is CPU of Renesas Technology. + This CPU has + - CPU clock 400MHz + - PCI support + - DDR-SDRAM controller + - etc ... + + Signed-off-by: Yusuke Goda + Signed-off-by: Nobuhiro Iwamatsu + +commit c2042f5952a686c414031309b8f244513bf578f0 +Author: goda.yusuke +Date: Fri Jan 25 20:46:36 2008 +0900 + + sh: Add support Renesas Solutions Migo-R board + + Migo-R is a board based on SH7722 and has may devices. + In this patch, supported SCIF, NOR flash and Ethernet. + + Signed-off-by: Yusuke Goda + Signed-off-by: Nobuhiro Iwamatsu + +commit 74d1e66d22dac91388bc538b2fe19f735edc5b82 +Author: Bartlomiej Sieka +Date: Thu Mar 27 15:06:40 2008 +0100 + + Fix host tool build breakage, take two + + Revert commit 87c8431f and fix build breakage so that the build continues + to work on FC systems. + + Signed-off-by: Bartlomiej Sieka + +commit 7e4a0d25ed18f6437bdf59ebfa49bb0edc2f24e6 +Author: Stefan Roese +Date: Wed Mar 19 09:36:47 2008 +0100 + + ppc4xx: Enable ECC on LWMON5 + + Since all ECC related problems seem to be resolved on LWMON5, this patch + now enables ECC support. + + We have to write the ECC bytes by zeroing and flushing in smaller + steps, since the whole 256MByte takes too long for the external + watchdog. + + Signed-off-by: Stefan Roese + +commit 6433fa202a91a6594dd48f06807ac38ba27fa0bb +Author: Larry Johnson +Date: Mon Mar 17 11:10:35 2008 -0500 + + ppc4xx: Updates to Korat-specific code + + This patch contains updates for changes for the Korat PPC440EPx board. + These changes include: + + (1) Support for "permanent" and "upgradable" copies of U-Boot, as + described in the new "doc/README.korat" file; + + (2) a new memory map for the registers in the board's CPLD; + + (3) a revised format for manufacturer's data in serial EEPROM; and + + (4) changes to track updates to U-Boot for the Sequoia board. + + Signed-off-by: Larry Johnson + +commit f766cdf89b3a2a7634b8c5869f606150e332036c +Author: Markus Brunner +Date: Thu Mar 27 10:46:25 2008 +0100 + + ppc4xx: PPC405EP Set EMAC noise filter bits + + This bug was introduced with commit aee747f19b460a0e9da20ff21e90fdaac1cec359 + which enabled CFG_4xx_GPIO_TABLE for PPC405 and unintentionally + disabled the setting of the emac noise filter bits for PPC405EP when CFG_4xx_GPIO_TABLE is set. + + Signed-off-by: Markus Brunner + Signed-off-by: Stefan Roese + +commit f66e2c8b25c04b79e5fb385bc8989c2de7f63991 +Author: Mike Nuss +Date: Wed Feb 20 11:54:20 2008 -0500 + + ppc4xx: Reconfigure PLL for 667MHz processor for PPC440EPx + + On PPC440EPx without a bootstrap I2C EEPROM, the PLL can be reconfigured + after startup to change the speed of the clocks. This patch adds the + option CFG_PLL_RECONFIG. If this option is set to 667, the CPU + initialization code will reconfigure the PLL to run the system with a CPU + frequency of 667MHz and PLB frequency of 166MHz, without the need for an + external EEPROM. + + Signed-off-by: Mike Nuss + Acked-by: Stefan Roese + +commit 87c8431fe24d48121f053fe67cff4ccfe097d4d1 +Author: Haavard Skinnemoen +Date: Thu Mar 27 09:12:40 2008 +0100 + + new-image: Fix host tool build breakage + + Signed-off-by: Haavard Skinnemoen + +commit 6fb4b640562a10daff0dbe537638d511b5b48650 +Author: Stefan Roese +Date: Thu Mar 27 10:24:03 2008 +0100 + + ppc: Set CFG_MEM_TOP_HIDE to 0 if not already defined + + Signed-off-by: Stefan Roese + +commit 9462732a3ec551c11862450902cd8ee1bedea6d9 +Author: Stefan Roese +Date: Wed Mar 19 10:23:43 2008 +0100 + + ppc4xx: Add fdt support to Prodrive alpr + + Since this board will probably be ported to arch/powerpc in the + near future, we add device tree support now. This way we are + "ready" for arch/powerpc from now on. + + Signed-off-by: Stefan Roese + +commit 511e4f9e7f7b6719e4d91d7f0fc89412b13b5150 +Author: Pieter Voorthuijsen +Date: Mon Mar 17 09:27:56 2008 +0100 + + ppc4xx: Enable cache support on the ALPR board + + Signed-off-by: Pieter Voorthuijsen + +commit 14f73ca679f6fdb44cff0b7304d419db41a0ab69 +Author: Stefan Roese +Date: Wed Mar 26 10:14:11 2008 +0100 + + ppc: Add CFG_MEM_TOP_HIDE option to hide memory area that doesn't get "touched" + + If CFG_MEM_TOP_HIDE is defined in the board config header, this specified + memory area will get subtracted from the top (end) of ram and won't get + "touched" at all by U-Boot. By fixing up gd->ram_size the Linux kernel + should gets passed the now "corrected" memory size and won't touch it + either. This should work for arch/ppc and arch/powerpc. Only Linux board + ports in arch/powerpc with bootwrapper support, which recalculate the + memory size from the SDRAM controller setup, will have to get fixed + in Linux additionally. + + This patch enables this config option on some PPC440EPx boards as a workaround + for the CHIP 11 errata. Here the description from the AMCC documentation: + + CHIP_11: End of memory range area restricted access. + Category: 3 + + Overview: + The 440EPx DDR controller does not acknowledge any + transaction which is determined to be crossing over the + end-of-memory-range boundary, even if the starting address is + within valid memory space. Any such transaction from any PLB4 + master will result in a PLB time-out on PLB4 bus. + + Impact: + In case of such misaligned bursts, PLB4 masters will not + retrieve any data at all, just the available data up to the + end of memory, especially the 440 CPU. For example, if a CPU + instruction required an operand located in memory within the + last 7 words of memory, the DCU master would burst read 8 + words to update the data cache and cross over the + end-of-memory-range boundary. Such a DCU read would not be + answered by the DDR controller, resulting in a PLB4 time-out + and ultimately in a Machine Check interrupt. The data would + be inaccessible to the CPU. + + Workaround: + Forbid any application to access the last 256 bytes of DDR + memory. For example, make your operating system believe that + the last 256 bytes of DDR memory are absent. AMCC has a patch + that does this, available for Linux. + + This patch sets CFG_MEM_TOP_HIDE for the following 440EPx boards: + lwmon5, korat, sequoia + + The other remaining 440EPx board were intentionally not included + since it is not clear to me, if they use the end of ram for some + other purpose. This is unclear, since these boards have CONFIG_PRAM + defined and even comments like this: + + PMC440.h: + /* esd expects pram at end of physical memory. + * So no logbuffer at the moment. + */ + + It is strongly recommended to not use the last 256 bytes on those + boards too. Patches from the board maintainers are welcome. + + Signed-off-by: Stefan Roese + +commit c664bf8c3c9bb9e236891f0d8dfda883e86d159b +Author: Stefan Roese +Date: Thu Mar 27 10:09:05 2008 +0100 + + ppc4xx: Fix Canyonlands linker script (remove bogus ASSERT) + + Signed-off-by: Stefan Roese + +commit d56a3ce179688cde61073a3690e21703d68fafd7 +Author: Stefan Roese +Date: Tue Mar 25 17:51:13 2008 +0100 + + ppc4xx: Correctly pass phyiscal FLASH base address into dtb + + The routine ft_board_setup() configures the EBC NOR mappings for the + Linux physmap_of driver. Since on 460EX/GT we remap the FLASH from + 0x4.fc00.0000 to 0x4.cc00.0000 because of the max. 16MByte boot-CS + problem, we need to pass the corrected address here too. + + Signed-off-by: Stefan Roese + +commit 9ad31989de12ce5c67b07c4867ead47465655c4b +Author: Stefan Roese +Date: Wed Mar 19 16:35:12 2008 +0100 + + ppc4xx: Fix compilation warning in 4xx_enet.c + + Signed-off-by: Stefan Roese + +commit 4c9e855734c523900322a7c3cdd9099b4f51b51d +Author: Stefan Roese +Date: Wed Mar 19 16:20:49 2008 +0100 + + ppc4xx: Add AMCC Glacier 406GT eval board support + + This patch adds support for the AMCC Glacier 460GT eval board. + The main difference to the Canyonlands board are listed here: + + - 4 ethernet ports instead of 2 + - no SATA port + - no USB port + + Currently EMAC2+3 are not working. This will be fixed in a later + release. + + Signed-off-by: Stefan Roese + +commit d8bd643141af4710d7f1b69bbab6b760de0af0a1 +Author: Stefan Roese +Date: Thu Mar 27 08:47:26 2008 +0100 + + ppc4xx: Mask 'vec' with 0x1f in uic_interrupt() for bit set/clear + + Signed-off-by: Stefan Roese + +commit b9670dd85be6e0496ef2e231043c23cad9b1d903 +Author: Anatolij Gustschin +Date: Wed Mar 26 21:05:43 2008 +0100 + + Fix out of tree building issue + + Currently U-Boot building in some external directory + doesn't work. This patch tries to fix the problem. + + Signed-off-by: Anatolij Gustschin + +commit d4ee711d8a5c366ee3f857c26b927d12e66614ff +Author: Anatolij Gustschin +Date: Wed Mar 26 18:13:33 2008 +0100 + + README: update documentation (availability, links, etc.) + + Fix typo in README + + Signed-off-by: Anatolij Gustschin + +commit e813eae3bfeba9c0bda9d1bf9fc3d081f790972f +Author: Anatolij Gustschin +Date: Wed Mar 26 17:47:44 2008 +0100 + + Fix compilation error in cmd_usb.c + + This patch fixes compilation error + cmd_usb.c: In function 'do_usb': + cmd_usb.c:552: error: void value not ignored as it ought to be + + Signed-off-by: Anatolij Gustschin + +commit d8c82db482d6b535d12b419d6440b88bf7091c9b +Author: Timur Tabi +Date: Fri Mar 14 17:45:29 2008 -0500 + + Add support for setting the I2C bus speed in fsl_i2c.c + + Add support to the Freescale I2C driver (fsl_i2c.c) for setting and querying + the I2C bus speed. Current 8[356]xx boards define the CFG_I2C_SPEED macro, + but fsl_i2c.c ignores it and uses conservative value when programming the + I2C bus speed. + + Signed-off-by: Timur Tabi + Acked-by: Andy Fleming + +commit d049cc7f71c0d875e8f5099d1ed23666a82b8f8e +Author: Wolfgang Denk +Date: Thu Mar 27 00:03:57 2008 +0100 + + Coding style cleanup, update CHANGELOG + + Signed-off-by: Wolfgang Denk + commit fd0b1fe3c388a77e8fe00cdd930ca317a91198d4 Author: Dave Liu Date: Wed Mar 26 22:55:32 2008 +0800 @@ -100,6 +1762,202 @@ Date: Wed Mar 26 22:47:06 2008 +0800 Signed-off-by: Dave Liu +commit b9e749e95354f33eb5dc6653c6db7d502adb95fe +Author: Markus Klotzbuecher +Date: Wed Mar 26 18:26:43 2008 +0100 + + USB, Storage: fix a bug introduced in commit + f6b44e0e4d18fe507833a0f76d24a9aa72c123f1 that will cause usb_stor_info + to only print only information on one storage device, but not for + multiple. + + Signed-off-by: Markus Klotzbuecher + +commit 841e5edd1623f3fecb6bffc5c2f938ed7a947360 +Author: Anatolij Gustschin +Date: Wed Mar 26 17:47:44 2008 +0100 + + Fix compilation error in cmd_usb.c + + This patch fixes compilation error + cmd_usb.c: In function 'do_usb': + cmd_usb.c:552: error: void value not ignored as it ought to be + + Signed-off-by: Anatolij Gustschin + Signed-off-by: Markus Klotzbuecher + +commit dd6c910aadf27c822f17b87eae1a9bd0b2e3aa15 +Author: Kumar Gala +Date: Wed Mar 26 08:53:53 2008 -0500 + + 85xx: Add cpu_mp_lmb_reserve helper to reserve boot page + + Provide a board_lmb_reserve helper function to ensure we reserve + the page of memory we are using for the boot page translation code. + + Signed-off-by: Kumar Gala + +commit 79679d80021ab095e639e250ca472fe526da02e2 +Author: Kumar Gala +Date: Wed Mar 26 08:34:25 2008 -0500 + + 85xx: Update multicore boot mechanism to ePAPR v0.81 spec + + The following changes are needed to be inline with ePAPR v0.81: + + * r4, r5 and now always set to 0 on boot release + * r7 is used to pass the size of the initial map area (IMA) + * EPAPR_MAGIC value changed for book-e processors + * changes in the spin table layout + * spin table supports a 64-bit physical release address + + Signed-off-by: Kumar Gala + +commit 25eedb2c1958a13110c7de1fc809b624053cc69c +Author: Jon Loeliger +Date: Wed Mar 19 15:02:07 2008 -0500 + + FSL: Clean up board/freescale/common/Makefile + + Each file that can be built here now follows some + CONFIG_ option so that they are appropriately built + or not, as needed. And CONFIG_ defines were added + to various board config files to make sure that happens. + + The other board/freescale/*/Makefiles no longer need + to reach up and over into ../common to build their + individually needed files any more. + + Boards that are CDS specific were renamed with cds_ prefix. + + Signed-off-by: Jon Loeliger + +commit a5af4b358a7caa9c0aa374d4d894bf762ec37669 +Author: Kumar Gala +Date: Wed Feb 27 22:00:27 2008 -0600 + + 85xx: Fix merge duplication + + ft_fixup_cpu() got duplicated in some merge snafu. Remove the duplicate. + + Signed-off-by: Kumar Gala + +commit 5893b3d0a4084f87a06a5d3dc03db91206818941 +Author: James Yang +Date: Tue Feb 12 16:35:07 2008 -0600 + + 85xx: Expand CCSR space with more DDR controller registers. + + Signed-off-by: James Yang + Signed-off-by: Jon Loeliger + Signed-off-by: Kumar Gala + +commit a3e77fa5359b3f9f59e4e946b46d57a53057cc85 +Author: James Yang +Date: Fri Feb 8 18:05:08 2008 -0600 + + 85xx: Speed up get_ddr_freq() and get_bus_freq() + + get_ddr_freq() and get_bus_freq() used get_sys_info() each time they were + called. However, get_sys_info() recalculates extraneous information when + called each time. Have get_ddr_freq() and get_bus_freq() return memoized + values from global_data instead. + + Signed-off-by: James Yang + Signed-off-by: Kumar Gala + +commit e9ea679918fbc9a53fa2f2a904aac874ea736036 +Author: James Yang +Date: Fri Feb 8 16:46:27 2008 -0600 + + 85xx: Show DDR memory data rate in addition to the memory clock frequency. + + Show the DDR memory data rate in addition to the memory clock + frequency. For DDR/DDR2 memories the memory data rate is 2x the + memory clock. + + Signed-off-by: James Yang + Signed-off-by: Kumar Gala + +commit 591933ca6eabc440e6ed6967233aaf56fce464a3 +Author: James Yang +Date: Fri Feb 8 16:44:53 2008 -0600 + + 85xx: get_tbclk() speed up and rounding fix + + Speed up get_tbclk() by referencing pre-computed bus clock + frequency value from global data instead of sys_info_t. Fix + rounding of result to nearest; previously it was rounding + upwards. + + Signed-off-by: James Yang + Signed-off-by: Kumar Gala + +commit 1ced121600b2060ab2ff9f0fddd9421fd70a0dc6 +Author: Andy Fleming +Date: Wed Feb 6 01:19:40 2008 -0600 + + Update SVR numbers to expand support + + FSL has taken to using SVR[16:23] as an SOC sub-version field. This + is used to distinguish certain variants within an SOC family. To + account for this, we add the SVR_SOC_VER() macro, and update the SVR_* + constants to reflect the larger value. We also add SVR numbers for all + of the current variants. Finally, to make things neater, rather than + use an enormous switch statement to print out the CPU type, we create + and array of SVR/name pairs (using a macro), and print out the CPU name + that matches the SVR SOC version. + + Signed-off-by: Andy Fleming + +commit b83eef440cf3cef816172ccbb5897ccd8e403cf3 +Author: Andy Fleming +Date: Wed Feb 6 01:12:57 2008 -0600 + + Add the Freescale PCI device IDs + + Signed-off-by: Andy Fleming + +commit 7aff0c051ad0613171cf2b9941ee48675c62e7cd +Author: Kumar Gala +Date: Thu Feb 14 11:04:23 2008 -0600 + + 85xx: Added support for multicore boot mechanism + + Added the cpu command that provides a generic mechanism to get status, + reset, and release secondary cores in multicore processors. + + Added support for using the ePAPR defined spin-table mechanism on 85xx. + + Signed-off-by: Kumar Gala + Signed-off-by: Andy Fleming + +commit ec2b74ffd36f02c6123725e7c2533dd2deaf4b64 +Author: Kumar Gala +Date: Thu Jan 17 16:48:33 2008 -0600 + + 85xx: Added support for multicore boot mechanism + + Added the cpu command that provides a generic mechanism to get status, + reset, and release secondary cores in multicore processors. + + Added support for using the ePAPR defined spin-table mechanism on 85xx. + + Signed-off-by: Kumar Gala + +commit f69766e4b5d47ecd3aa58677a8da875694f364f2 +Author: Kumar Gala +Date: Wed Jan 30 14:55:14 2008 -0600 + + 85xx: Add the concept of CFG_CCSRBAR_PHYS + + When we go to 36-bit physical addresses we need to keep the concept of + the physical CCSRBAR address seperate from the virtual one. + + For the majority of boards CFG_CCSBAR_PHYS == CFG_CCSRBAR + + Signed-off-by: Kumar Gala + commit 5b5eb9ca5b778f763bcf332697b35cc1e747626e Author: Wolfgang Denk Date: Wed Mar 26 15:38:47 2008 +0100 diff --git a/board/MigoR/config.mk b/board/MigoR/config.mk index c68cb723df..2c5085a91f 100644 --- a/board/MigoR/config.mk +++ b/board/MigoR/config.mk @@ -29,4 +29,3 @@ # TEXT_BASE = 0x8FFC0000 - diff --git a/board/MigoR/lowlevel_init.S b/board/MigoR/lowlevel_init.S index 7fd771d693..2ec8e04b18 100644 --- a/board/MigoR/lowlevel_init.S +++ b/board/MigoR/lowlevel_init.S @@ -42,7 +42,6 @@ .align 2 lowlevel_init: - mov.l CCR_A, r1 ! Address of Cache Control Register mov.l CCR_D, r0 ! Instruction Cache Invalidate mov.l r0, @r1 @@ -100,7 +99,6 @@ lowlevel_init: mov.l r0, @r1 bsc_init: - mov.l CMNCR_A, r1 ! CMNCR address -> R1 mov.l CMNCR_D, r0 ! CMNCR data -> R0 mov.l r0, @r1 ! CMNCR set @@ -188,8 +186,6 @@ bsc_init: rts mov #0, r0 - - .align 4 CCR_A: .long CCR @@ -266,4 +262,3 @@ PSCR_D: .word 0x0000 RWTCSR_D_1: .word 0xA507 RWTCSR_D_2: .word 0xA504 ! 20080115 RWTCNT_D: .word 0x5A00 - diff --git a/board/MigoR/migo_r.c b/board/MigoR/migo_r.c index 53f4bb229f..b31f37d0f6 100644 --- a/board/MigoR/migo_r.c +++ b/board/MigoR/migo_r.c @@ -51,4 +51,3 @@ int dram_init (void) void led_set_state (unsigned short value) { } - diff --git a/board/MigoR/u-boot.lds b/board/MigoR/u-boot.lds index 1877b812fe..692bc62918 100644 --- a/board/MigoR/u-boot.lds +++ b/board/MigoR/u-boot.lds @@ -103,4 +103,3 @@ SECTIONS PROVIDE (_end = .); } - diff --git a/board/freescale/m5275evb/mii.c b/board/freescale/m5275evb/mii.c index bbc93f6d48..6c7ace9566 100644 --- a/board/freescale/m5275evb/mii.c +++ b/board/freescale/m5275evb/mii.c @@ -50,11 +50,11 @@ int fecpin_setclear(struct eth_device *dev, int setclear) } } else { if (info->iobase == CFG_FEC0_IOBASE) { - gpio->par_feci2c &= ~0x0F00; - gpio->par_fec0hl &= ~0xC0; + gpio->par_feci2c &= ~0x0F00; + gpio->par_fec0hl &= ~0xC0; } else { - gpio->par_feci2c &= ~0x00A0; - gpio->par_fec1hl &= ~0xC0; + gpio->par_feci2c &= ~0x00A0; + gpio->par_fec1hl &= ~0xC0; } } diff --git a/board/mpr2/mpr2.c b/board/mpr2/mpr2.c index 2ddb0c10c1..98557b400b 100644 --- a/board/mpr2/mpr2.c +++ b/board/mpr2/mpr2.c @@ -67,7 +67,7 @@ int board_init(void) /* set Pin Select Register D: Reserved, SIOF1_TxD, Reserved, SIOF1_MCLK, Reserved, SIOF1_SYNC, Reserved, SCIF1_SCK, Reserved */ __raw_writew(0x0000, PSELD); /* 0 00 00 00 00 00 00 00 0 */ - + /* OTH: (00) Other fuction * GPO: (01) General Purpose Output * GPI: (11) General Purpose Input @@ -159,4 +159,3 @@ int dram_init(void) printf("SDRAM: %dMB\n", CFG_SDRAM_SIZE / (1024 * 1024)); return 0; } - diff --git a/board/mpr2/u-boot.lds b/board/mpr2/u-boot.lds index 6fee7f2542..eda6b442ab 100644 --- a/board/mpr2/u-boot.lds +++ b/board/mpr2/u-boot.lds @@ -7,7 +7,7 @@ * * Copyright (C) 2008 * Mark Jonas - * + * * See file CREDITS for list of people who contributed to this * project. * diff --git a/common/cmd_ambapp.c b/common/cmd_ambapp.c index 738412b7fa..43427bb3c5 100644 --- a/common/cmd_ambapp.c +++ b/common/cmd_ambapp.c @@ -33,11 +33,11 @@ DECLARE_GLOBAL_DATA_PTR; /* We put these variables into .data section so that they are zero * when entering the AMBA Plug & Play routines (in cpu/cpu/ambapp.c) - * the first time. BSS is not garantueed to be zero since BSS + * the first time. BSS is not garantueed to be zero since BSS * hasn't been cleared the first times entering the CPU AMBA functions. * * The AMBA PnP routines call these functions if ambapp_???_print is set. - * + * */ int ambapp_apb_print __attribute__ ((section(".data"))) = 0; int ambapp_ahb_print __attribute__ ((section(".data"))) = 0; diff --git a/common/usb_storage.c b/common/usb_storage.c index d263b6c0d0..7c08f95775 100644 --- a/common/usb_storage.c +++ b/common/usb_storage.c @@ -199,7 +199,7 @@ int usb_stor_info(void) } return 0; } - + printf("No storage devices, perhaps not 'usb start'ed..?\n"); return 1; } diff --git a/cpu/leon2/start.S b/cpu/leon2/start.S index 937ea1ed77..60d3fadef4 100644 --- a/cpu/leon2/start.S +++ b/cpu/leon2/start.S @@ -118,7 +118,7 @@ _trap_table: TRAPI(13); ! 1d IRQ level 13 TRAPI(14); ! 1e IRQ level 14 TRAP(_nmi_trap); ! 1f IRQ level 15 / - ! NMI (non maskable interrupt) + ! NMI (non maskable interrupt) BAD_TRAP; ! 20 r_register_access_error BAD_TRAP; ! 21 instruction access error BAD_TRAP; ! 22 @@ -213,9 +213,9 @@ _hardreset: nop /* Init Cache */ - set (LEON2_PREGS+LEON_REG_CACHECTRL_OFFSET), %g1 - set 0x0081000f, %g2 - st %g2, [%g1] + set (LEON2_PREGS+LEON_REG_CACHECTRL_OFFSET), %g1 + set 0x0081000f, %g2 + st %g2, [%g1] mov %g0, %y clr %g1 @@ -584,7 +584,7 @@ trap_setup: or %t_wim, %g2, %g2 and %g2, 0xff, %g2 - save %g0, %g0, %g0 ! get in window to be saved + save %g0, %g0, %g0 ! get in window to be saved /* Set new %wim value */ wr %g2, 0x0, %wim diff --git a/cpu/leon3/start.S b/cpu/leon3/start.S index 807f7e8dae..2f1d099e37 100644 --- a/cpu/leon3/start.S +++ b/cpu/leon3/start.S @@ -359,8 +359,8 @@ prom_relocate_loop: nop nop nop - -/* If CACHE snooping is available in hardware the + +/* If CACHE snooping is available in hardware the * variable leon3_snooping_avail will be set to * 0x800000 else 0. */ diff --git a/cpu/mcf52x2/speed.c b/cpu/mcf52x2/speed.c index 85a5c4de38..5fafcd8c5f 100644 --- a/cpu/mcf52x2/speed.c +++ b/cpu/mcf52x2/speed.c @@ -67,11 +67,13 @@ int get_clocks (void) #if defined(CONFIG_M5275) volatile pll_t *pll = (volatile pll_t *)(MMAP_PLL); - /* Setup PLL */ - pll->syncr = 0x01080000; - while (!(pll->synsr & FMPLL_SYNSR_LOCK)); - pll->syncr = 0x01000000; - while (!(pll->synsr & FMPLL_SYNSR_LOCK)); + /* Setup PLL */ + pll->syncr = 0x01080000; + while (!(pll->synsr & FMPLL_SYNSR_LOCK) + ; + pll->syncr = 0x01000000; + while (!(pll->synsr & FMPLL_SYNSR_LOCK)) + ; #endif gd->cpu_clk = CFG_CLK; diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c index 4a7225202c..c53c226d28 100644 --- a/drivers/net/e1000.c +++ b/drivers/net/e1000.c @@ -21,7 +21,7 @@ tested on both gig copper and gig fiber boards You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 59 - Temple Place - Suite 330, Boston, MA 02111-1307, USA. + Temple Place - Suite 330, Boston, MA 02111-1307, USA. The full GNU General Public License is included in this distribution in the file called LICENSE. @@ -52,7 +52,7 @@ tested on both gig copper and gig fiber boards #undef virt_to_bus #define virt_to_bus(x) ((unsigned long)x) #define bus_to_phys(devno, a) pci_mem_to_phys(devno, a) -#define mdelay(n) udelay((n)*1000) +#define mdelay(n) udelay((n)*1000) #define E1000_DEFAULT_PBA 0x00000030 @@ -646,8 +646,8 @@ e1000_set_mac_type(struct e1000_hw *hw) hw->mac_type = e1000_82546; break; case E1000_DEV_ID_82541ER: - hw->mac_type = e1000_82541_rev_2; - break; + hw->mac_type = e1000_82541_rev_2; + break; default: /* Should never have loaded on this device */ return -E1000_ERR_MAC_TYPE; @@ -1061,12 +1061,12 @@ e1000_setup_fiber_link(struct eth_device *nic) * configure the two flow control enable bits in the CTRL register. * * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, but - * not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but we do - * not support receiving pause frames). - * 3: Both Rx and TX flow control (symmetric) are enabled. + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, but + * not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but we do + * not support receiving pause frames). + * 3: Both Rx and TX flow control (symmetric) are enabled. */ switch (hw->fc) { case e1000_fc_none: @@ -1229,7 +1229,7 @@ e1000_setup_copper_link(struct eth_device *nic) #if 0 /* Options: * disable_polarity_correction = 0 (default) - * Automatic Correction for Reversed Cable Polarity + * Automatic Correction for Reversed Cable Polarity * 0 - Disabled * 1 - Enabled */ @@ -1271,14 +1271,14 @@ e1000_setup_copper_link(struct eth_device *nic) /* Options: * autoneg = 1 (default) - * PHY will advertise value(s) parsed from - * autoneg_advertised and fc + * PHY will advertise value(s) parsed from + * autoneg_advertised and fc * autoneg = 0 - * PHY will be set to 10H, 10F, 100H, or 100F - * depending on value parsed from forced_speed_duplex. + * PHY will be set to 10H, 10F, 100H, or 100F + * depending on value parsed from forced_speed_duplex. */ - /* Is autoneg enabled? This is enabled by default or by software override. + /* Is autoneg enabled? This is enabled by default or by software override. * If so, call e1000_phy_setup_autoneg routine to parse the * autoneg_advertised and fc options. If autoneg is NOT enabled, then the * user should have provided a speed/duplex override. If so, then call @@ -1353,11 +1353,11 @@ e1000_setup_copper_link(struct eth_device *nic) if (phy_data & MII_SR_LINK_STATUS) { /* We have link, so we need to finish the config process: * 1) Set up the MAC to the current PHY speed/duplex - * if we are on 82543. If we - * are on newer silicon, we only need to configure - * collision distance in the Transmit Control Register. + * if we are on 82543. If we + * are on newer silicon, we only need to configure + * collision distance in the Transmit Control Register. * 2) Set up flow control on the MAC to that established with - * the link partner. + * the link partner. */ if (hw->mac_type >= e1000_82544) { e1000_config_collision_dist(hw); @@ -1418,7 +1418,7 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw) /* First we clear all the 10/100 mb speed bits in the Auto-Neg * Advertisement Register (Address 4) and the 1000 mb speed bits in - * the 1000Base-T Control Register (Address 9). + * the 1000Base-T Control Register (Address 9). */ mii_autoneg_adv_reg &= ~REG4_SPEED_MASK; mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK; @@ -1468,14 +1468,14 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw) * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. * * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames - * but we do not support receiving pause frames). - * 3: Both Rx and TX flow control (symmetric) are enabled. + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * but we do not support receiving pause frames). + * 3: Both Rx and TX flow control (symmetric) are enabled. * other: No software override. The flow control configuration - * in the EEPROM is used. + * in the EEPROM is used. */ switch (hw->fc) { case e1000_fc_none: /* 0 */ @@ -1630,12 +1630,12 @@ e1000_force_mac_fc(struct e1000_hw *hw) * according to the "hw->fc" parameter. * * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause - * frames but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames - * frames but we do not receive pause frames). - * 3: Both Rx and TX flow control (symmetric) is enabled. + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause + * frames but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * frames but we do not receive pause frames). + * 3: Both Rx and TX flow control (symmetric) is enabled. * other: No other values should be possible at this point. */ @@ -1752,14 +1752,14 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution *-------|---------|-------|---------|-------------------- - * 0 | 0 | DC | DC | e1000_fc_none - * 0 | 1 | 0 | DC | e1000_fc_none - * 0 | 1 | 1 | 0 | e1000_fc_none - * 0 | 1 | 1 | 1 | e1000_fc_tx_pause - * 1 | 0 | 0 | DC | e1000_fc_none - * 1 | DC | 1 | DC | e1000_fc_full - * 1 | 1 | 0 | 0 | e1000_fc_none - * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + * 0 | 0 | DC | DC | e1000_fc_none + * 0 | 1 | 0 | DC | e1000_fc_none + * 0 | 1 | 1 | 0 | e1000_fc_none + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + * 1 | 0 | 0 | DC | e1000_fc_none + * 1 | DC | 1 | DC | e1000_fc_full + * 1 | 1 | 0 | 0 | e1000_fc_none + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause * */ /* Are both PAUSE bits set to 1? If so, this implies @@ -1771,7 +1771,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result *-------|---------|-------|---------|-------------------- - * 1 | DC | 1 | DC | e1000_fc_full + * 1 | DC | 1 | DC | e1000_fc_full * */ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && @@ -1796,7 +1796,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result *-------|---------|-------|---------|-------------------- - * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause * */ else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && @@ -1813,7 +1813,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result *-------|---------|-------|---------|-------------------- - * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause * */ else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && @@ -1855,7 +1855,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw) ("Flow Control = RX PAUSE frames only.\r\n"); } - /* Now we need to do one last check... If we auto- + /* Now we need to do one last check... If we auto- * negotiated to HALF DUPLEX, flow control should not be * enabled per IEEE 802.3 spec. */ @@ -1919,7 +1919,7 @@ e1000_check_for_link(struct eth_device *nic) /* If we have a copper PHY then we only want to go out to the PHY * registers to see if Auto-Neg has completed and/or if our link - * status has changed. The get_link_status flag will be set if we + * status has changed. The get_link_status flag will be set if we * receive a Link Status Change interrupt or we have Rx Sequence * Errors. */ @@ -1976,7 +1976,7 @@ e1000_check_for_link(struct eth_device *nic) /* At this point we know that we are on copper and we have * auto-negotiated link. These are conditions for checking the link - * parter capability register. We use the link partner capability to + * parter capability register. We use the link partner capability to * determine if TBI Compatibility needs to be turned on or off. If * the link partner advertises any speed in addition to Gigabit, then * we assume that they are GMII-based, and TBI compatibility is not @@ -2494,34 +2494,33 @@ e1000_phy_reset(struct e1000_hw *hw) return 0; } -static int -e1000_set_phy_type(struct e1000_hw *hw) +static int e1000_set_phy_type (struct e1000_hw *hw) { - DEBUGFUNC(); + DEBUGFUNC (); - if(hw->mac_type == e1000_undefined) - return -E1000_ERR_PHY_TYPE; + if (hw->mac_type == e1000_undefined) + return -E1000_ERR_PHY_TYPE; - switch(hw->phy_id) { - case M88E1000_E_PHY_ID: - case M88E1000_I_PHY_ID: - case M88E1011_I_PHY_ID: - hw->phy_type = e1000_phy_m88; - break; - case IGP01E1000_I_PHY_ID: - if(hw->mac_type == e1000_82541 || - hw->mac_type == e1000_82541_rev_2) { - hw->phy_type = e1000_phy_igp; - break; - } - /* Fall Through */ - default: - /* Should never have loaded on this device */ - hw->phy_type = e1000_phy_undefined; - return -E1000_ERR_PHY_TYPE; - } + switch (hw->phy_id) { + case M88E1000_E_PHY_ID: + case M88E1000_I_PHY_ID: + case M88E1011_I_PHY_ID: + hw->phy_type = e1000_phy_m88; + break; + case IGP01E1000_I_PHY_ID: + if (hw->mac_type == e1000_82541 || + hw->mac_type == e1000_82541_rev_2) { + hw->phy_type = e1000_phy_igp; + break; + } + /* Fall Through */ + default: + /* Should never have loaded on this device */ + hw->phy_type = e1000_phy_undefined; + return -E1000_ERR_PHY_TYPE; + } - return E1000_SUCCESS; + return E1000_SUCCESS; } /****************************************************************************** @@ -2825,8 +2824,8 @@ e1000_configure_rx(struct e1000_hw *hw) #endif /* Set the interrupt throttling rate. Value is calculated * as DEFAULT_ITR = 1/(MAX_INTS_PER_SEC * 256ns) */ -#define MAX_INTS_PER_SEC 8000 -#define DEFAULT_ITR 1000000000/(MAX_INTS_PER_SEC * 256) +#define MAX_INTS_PER_SEC 8000 +#define DEFAULT_ITR 1000000000/(MAX_INTS_PER_SEC * 256) E1000_WRITE_REG(hw, ITR, DEFAULT_ITR); } diff --git a/include/ambapp.h b/include/ambapp.h index 7494e594d8..42c990c028 100644 --- a/include/ambapp.h +++ b/include/ambapp.h @@ -41,7 +41,7 @@ /* Max devices this software will support */ #define LEON3_AHB_MASTERS 16 #define LEON3_AHB_SLAVES 16 - /*#define LEON3_APB_MASTERS 1*//* Number of APB buses that has Plug&Play */ +/*#define LEON3_APB_MASTERS 1*/ /* Number of APB buses that has Plug&Play */ #define LEON3_APB_SLAVES 16 /* Total number of APB slaves per APB bus */ /* Vendor codes */ diff --git a/include/asm-ppc/immap_85xx.h b/include/asm-ppc/immap_85xx.h index 3506aec5ec..01cb2d74fa 100644 --- a/include/asm-ppc/immap_85xx.h +++ b/include/asm-ppc/immap_85xx.h @@ -57,7 +57,7 @@ typedef struct ccsr_local_ecm { uint lawbar7; /* 0xce8 - Local Access Window 7 Base Address Register */ char res19[4]; uint lawar7; /* 0xcf0 - Local Access Window 7 Attributes Register */ - char res20[780]; // XXX: LAW 8, LAW9 for 8572 + char res20[780]; /* XXX: LAW 8, LAW9 for 8572 */ uint eebacr; /* 0x1000 - ECM CCB Address Configuration Register */ char res21[12]; uint eebpcr; /* 0x1010 - ECM CCB Port Configuration Register */ diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index 544cc010db..aec325b470 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -18,9 +18,9 @@ #define MSR_SF (1<<63) #define MSR_ISF (1<<61) #endif /* CONFIG_PPC64BRIDGE */ -#define MSR_UCLE (1<<26) /* User-mode cache lock enable (e500) */ +#define MSR_UCLE (1<<26) /* User-mode cache lock enable (e500) */ #define MSR_VEC (1<<25) /* Enable AltiVec(74xx) */ -#define MSR_SPE (1<<25) /* Enable SPE(e500) */ +#define MSR_SPE (1<<25) /* Enable SPE(e500) */ #define MSR_POW (1<<18) /* Enable Power Management */ #define MSR_WE (1<<18) /* Wait State Enable */ #define MSR_TGPR (1<<17) /* TLB Update registers in use */ @@ -32,19 +32,19 @@ #define MSR_ME (1<<12) /* Machine Check Enable */ #define MSR_FE0 (1<<11) /* Floating Exception mode 0 */ #define MSR_SE (1<<10) /* Single Step */ -#define MSR_DWE (1<<10) /* Debug Wait Enable (4xx) */ -#define MSR_UBLE (1<<10) /* BTB lock enable (e500) */ +#define MSR_DWE (1<<10) /* Debug Wait Enable (4xx) */ +#define MSR_UBLE (1<<10) /* BTB lock enable (e500) */ #define MSR_BE (1<<9) /* Branch Trace */ #define MSR_DE (1<<9) /* Debug Exception Enable */ #define MSR_FE1 (1<<8) /* Floating Exception mode 1 */ #define MSR_IP (1<<6) /* Exception prefix 0x000/0xFFF */ #define MSR_IR (1<<5) /* Instruction Relocate */ -#define MSR_IS (1<<5) /* Book E Instruction space */ +#define MSR_IS (1<<5) /* Book E Instruction space */ #define MSR_DR (1<<4) /* Data Relocate */ -#define MSR_DS (1<<4) /* Book E Data space */ +#define MSR_DS (1<<4) /* Book E Data space */ #define MSR_PE (1<<3) /* Protection Enable */ #define MSR_PX (1<<2) /* Protection Exclusive Mode */ -#define MSR_PMM (1<<2) /* Performance monitor mark bit (e500) */ +#define MSR_PMM (1<<2) /* Performance monitor mark bit (e500) */ #define MSR_RI (1<<1) /* Recoverable Exception */ #define MSR_LE (1<<0) /* Little Endian */ @@ -54,7 +54,7 @@ #define MSR_ MSR_ME|MSR_RI #endif #ifndef CONFIG_E500 -#define MSR_KERNEL MSR_|MSR_IR|MSR_DR +#define MSR_KERNEL MSR_|MSR_IR|MSR_DR #else #define MSR_KERNEL MSR_ME #endif @@ -103,9 +103,9 @@ #define SPRN_DAC1 0x3F6 /* Data Address Compare 1 */ #define SPRN_DAC2 0x3F7 /* Data Address Compare 2 */ #else -#define SPRN_DAC1 0x13C /* Book E Data Address Compare 1 */ -#define SPRN_DAC2 0x13D /* Book E Data Address Compare 2 */ -#endif /* CONFIG_BOOKE */ +#define SPRN_DAC1 0x13C /* Book E Data Address Compare 1 */ +#define SPRN_DAC2 0x13D /* Book E Data Address Compare 2 */ +#endif /* CONFIG_BOOKE */ #define SPRN_DAR 0x013 /* Data Address Register */ #define SPRN_DBAT0L 0x219 /* Data BAT 0 Lower Register */ #define SPRN_DBAT0U 0x218 /* Data BAT 0 Upper Register */ @@ -115,14 +115,14 @@ #define SPRN_DBAT2U 0x21C /* Data BAT 2 Upper Register */ #define SPRN_DBAT3L 0x21F /* Data BAT 3 Lower Register */ #define SPRN_DBAT3U 0x21E /* Data BAT 3 Upper Register */ -#define SPRN_DBAT4L 0x239 /* Data BAT 4 Lower Register */ -#define SPRN_DBAT4U 0x238 /* Data BAT 4 Upper Register */ -#define SPRN_DBAT5L 0x23B /* Data BAT 5 Lower Register */ -#define SPRN_DBAT5U 0x23A /* Data BAT 5 Upper Register */ -#define SPRN_DBAT6L 0x23D /* Data BAT 6 Lower Register */ -#define SPRN_DBAT6U 0x23C /* Data BAT 6 Upper Register */ -#define SPRN_DBAT7L 0x23F /* Data BAT 7 Lower Register */ -#define SPRN_DBAT7U 0x23E /* Data BAT 7 Lower Register */ +#define SPRN_DBAT4L 0x239 /* Data BAT 4 Lower Register */ +#define SPRN_DBAT4U 0x238 /* Data BAT 4 Upper Register */ +#define SPRN_DBAT5L 0x23B /* Data BAT 5 Lower Register */ +#define SPRN_DBAT5U 0x23A /* Data BAT 5 Upper Register */ +#define SPRN_DBAT6L 0x23D /* Data BAT 6 Lower Register */ +#define SPRN_DBAT6U 0x23C /* Data BAT 6 Upper Register */ +#define SPRN_DBAT7L 0x23F /* Data BAT 7 Lower Register */ +#define SPRN_DBAT7U 0x23E /* Data BAT 7 Lower Register */ #define SPRN_DBCR 0x3F2 /* Debug Control Regsiter */ #define DBCR_EDM 0x80000000 #define DBCR_IDM 0x40000000 @@ -157,18 +157,18 @@ #define DBCR_JOI 0x00000002 /* JTAG Serial Outbound Int. Enable */ #define DBCR_JII 0x00000001 /* JTAG Serial Inbound Int. Enable */ #ifndef CONFIG_BOOKE -#define SPRN_DBCR0 0x3F2 /* Debug Control Register 0 */ +#define SPRN_DBCR0 0x3F2 /* Debug Control Register 0 */ #else -#define SPRN_DBCR0 0x134 /* Book E Debug Control Register 0 */ +#define SPRN_DBCR0 0x134 /* Book E Debug Control Register 0 */ #endif /* CONFIG_BOOKE */ #ifndef CONFIG_BOOKE #define SPRN_DBCR1 0x3BD /* Debug Control Register 1 */ #define SPRN_DBSR 0x3F0 /* Debug Status Register */ #else -#define SPRN_DBCR1 0x135 /* Book E Debug Control Register 1 */ -#define SPRN_DBSR 0x130 /* Book E Debug Status Register */ -#define DBSR_IC 0x08000000 /* Book E Instruction Completion */ -#define DBSR_TIE 0x01000000 /* Book E Trap Instruction Event */ +#define SPRN_DBCR1 0x135 /* Book E Debug Control Register 1 */ +#define SPRN_DBSR 0x130 /* Book E Debug Status Register */ +#define DBSR_IC 0x08000000 /* Book E Instruction Completion */ +#define DBSR_TIE 0x01000000 /* Book E Trap Instruction Event */ #endif /* CONFIG_BOOKE */ #define SPRN_DCCR 0x3FA /* Data Cache Cacheability Register */ #define DCCR_NOCACHE 0 /* Noncacheable */ @@ -180,7 +180,7 @@ #ifndef CONFIG_BOOKE #define SPRN_DEAR 0x3D5 /* Data Error Address Register */ #else -#define SPRN_DEAR 0x03D /* Book E Data Error Address Register */ +#define SPRN_DEAR 0x03D /* Book E Data Error Address Register */ #endif /* CONFIG_BOOKE */ #define SPRN_DEC 0x016 /* Decrement Register */ #define SPRN_DMISS 0x3D0 /* Data TLB Miss Register */ @@ -189,7 +189,7 @@ #ifndef CONFIG_BOOKE #define SPRN_ESR 0x3D4 /* Exception Syndrome Register */ #else -#define SPRN_ESR 0x03E /* Book E Exception Syndrome Register */ +#define SPRN_ESR 0x03E /* Book E Exception Syndrome Register */ #endif /* CONFIG_BOOKE */ #define ESR_IMCP 0x80000000 /* Instr. Machine Check - Protection */ #define ESR_IMCN 0x40000000 /* Instr. Machine Check - Non-config */ @@ -246,8 +246,8 @@ #define SPRN_IAC1 0x3F4 /* Instruction Address Compare 1 */ #define SPRN_IAC2 0x3F5 /* Instruction Address Compare 2 */ #else -#define SPRN_IAC1 0x138 /* Book E Instruction Address Compare 1 */ -#define SPRN_IAC2 0x139 /* Book E Instruction Address Compare 2 */ +#define SPRN_IAC1 0x138 /* Book E Instruction Address Compare 1 */ +#define SPRN_IAC2 0x139 /* Book E Instruction Address Compare 2 */ #endif /* CONFIG_BOOKE */ #define SPRN_IBAT0L 0x211 /* Instruction BAT 0 Lower Register */ #define SPRN_IBAT0U 0x210 /* Instruction BAT 0 Upper Register */ @@ -257,14 +257,14 @@ #define SPRN_IBAT2U 0x214 /* Instruction BAT 2 Upper Register */ #define SPRN_IBAT3L 0x217 /* Instruction BAT 3 Lower Register */ #define SPRN_IBAT3U 0x216 /* Instruction BAT 3 Upper Register */ -#define SPRN_IBAT4L 0x231 /* Instruction BAT 4 Lower Register */ -#define SPRN_IBAT4U 0x230 /* Instruction BAT 4 Upper Register */ -#define SPRN_IBAT5L 0x233 /* Instruction BAT 5 Lower Register */ -#define SPRN_IBAT5U 0x232 /* Instruction BAT 5 Upper Register */ -#define SPRN_IBAT6L 0x235 /* Instruction BAT 6 Lower Register */ -#define SPRN_IBAT6U 0x234 /* Instruction BAT 6 Upper Register */ -#define SPRN_IBAT7L 0x237 /* Instruction BAT 7 Lower Register */ -#define SPRN_IBAT7U 0x236 /* Instruction BAT 7 Upper Register */ +#define SPRN_IBAT4L 0x231 /* Instruction BAT 4 Lower Register */ +#define SPRN_IBAT4U 0x230 /* Instruction BAT 4 Upper Register */ +#define SPRN_IBAT5L 0x233 /* Instruction BAT 5 Lower Register */ +#define SPRN_IBAT5U 0x232 /* Instruction BAT 5 Upper Register */ +#define SPRN_IBAT6L 0x235 /* Instruction BAT 6 Lower Register */ +#define SPRN_IBAT6U 0x234 /* Instruction BAT 6 Upper Register */ +#define SPRN_IBAT7L 0x237 /* Instruction BAT 7 Lower Register */ +#define SPRN_IBAT7U 0x236 /* Instruction BAT 7 Upper Register */ #define SPRN_ICCR 0x3FB /* Instruction Cache Cacheability Register */ #define ICCR_NOCACHE 0 /* Noncacheable */ #define ICCR_CACHE 1 /* Cacheable */ @@ -273,10 +273,10 @@ #define SPRN_ICTC 0x3FB /* Instruction Cache Throttling Control Reg */ #define SPRN_IMISS 0x3D4 /* Instruction TLB Miss Register */ #define SPRN_IMMR 0x27E /* Internal Memory Map Register */ -#define SPRN_LDSTCR 0x3F8 /* Load/Store Control Register */ +#define SPRN_LDSTCR 0x3F8 /* Load/Store Control Register */ #define SPRN_L2CR 0x3F9 /* Level 2 Cache Control Regsiter */ #define SPRN_LR 0x008 /* Link Register */ -#define SPRN_MBAR 0x137 /* System memory base address */ +#define SPRN_MBAR 0x137 /* System memory base address */ #define SPRN_MMCR0 0x3B8 /* Monitor Mode Control Register 0 */ #define SPRN_MMCR1 0x3BC /* Monitor Mode Control Register 1 */ #define SPRN_PBL1 0x3FC /* Protection Bound Lower 1 */ @@ -287,8 +287,8 @@ #define SPRN_PID 0x3B1 /* Process ID */ #define SPRN_PIR 0x3FF /* Processor Identification Register */ #else -#define SPRN_PID 0x030 /* Book E Process ID */ -#define SPRN_PIR 0x11E /* Book E Processor Identification Register */ +#define SPRN_PID 0x030 /* Book E Process ID */ +#define SPRN_PIR 0x11E /* Book E Processor Identification Register */ #endif /* CONFIG_BOOKE */ #define SPRN_PIT 0x3DB /* Programmable Interval Timer */ #define SPRN_PMC1 0x3B9 /* Performance Counter Register 1 */ @@ -331,7 +331,7 @@ #ifndef CONFIG_BOOKE #define SPRN_TCR 0x3DA /* Timer Control Register */ #else -#define SPRN_TCR 0x154 /* Book E Timer Control Register */ +#define SPRN_TCR 0x154 /* Book E Timer Control Register */ #endif /* CONFIG_BOOKE */ #define TCR_WP(x) (((x)&0x3)<<30) /* WDT Period */ #define WP_2_17 0 /* 2^17 clocks */ @@ -362,11 +362,11 @@ #define SPRN_THRM2 0x3FD /* Thermal Management Register 2 */ #define SPRN_THRM3 0x3FE /* Thermal Management Register 3 */ #define THRM3_E (1<<31) -#define SPRN_TLBMISS 0x3D4 /* 980 7450 TLB Miss Register */ +#define SPRN_TLBMISS 0x3D4 /* 980 7450 TLB Miss Register */ #ifndef CONFIG_BOOKE #define SPRN_TSR 0x3D8 /* Timer Status Register */ #else -#define SPRN_TSR 0x150 /* Book E Timer Status Register */ +#define SPRN_TSR 0x150 /* Book E Timer Status Register */ #endif /* CONFIG_BOOKE */ #define TSR_ENW 0x80000000 /* Enable Next Watchdog */ #define TSR_WIS 0x40000000 /* WDT Interrupt Status */ @@ -424,40 +424,40 @@ #define SPRN_IVOR15 0x19f /* Interrupt Vector Offset Register 15 */ /* e500 definitions */ -#define SPRN_L1CFG0 0x203 /* L1 Cache Configuration Register 0 */ -#define SPRN_L1CFG1 0x204 /* L1 Cache Configuration Register 1 */ -#define SPRN_L1CSR0 0x3f2 /* L1 Data Cache Control and Status Register 0 */ -#define L1CSR0_CPE 0x00010000 /* Data Cache Parity Enable */ -#define L1CSR0_DCFI 0x00000002 /* Data Cache Flash Invalidate */ -#define L1CSR0_DCE 0x00000001 /* Data Cache Enable */ -#define SPRN_L1CSR1 0x3f3 /* L1 Instruction Cache Control and Status Register 1 */ -#define L1CSR1_CPE 0x00010000 /* Instruction Cache Parity Enable */ -#define L1CSR1_ICFI 0x00000002 /* Instruction Cache Flash Invalidate */ -#define L1CSR1_ICE 0x00000001 /* Instruction Cache Enable */ +#define SPRN_L1CFG0 0x203 /* L1 Cache Configuration Register 0 */ +#define SPRN_L1CFG1 0x204 /* L1 Cache Configuration Register 1 */ +#define SPRN_L1CSR0 0x3f2 /* L1 Data Cache Control and Status Register 0 */ +#define L1CSR0_CPE 0x00010000 /* Data Cache Parity Enable */ +#define L1CSR0_DCFI 0x00000002 /* Data Cache Flash Invalidate */ +#define L1CSR0_DCE 0x00000001 /* Data Cache Enable */ +#define SPRN_L1CSR1 0x3f3 /* L1 Instruction Cache Control and Status Register 1 */ +#define L1CSR1_CPE 0x00010000 /* Instruction Cache Parity Enable */ +#define L1CSR1_ICFI 0x00000002 /* Instruction Cache Flash Invalidate */ +#define L1CSR1_ICE 0x00000001 /* Instruction Cache Enable */ #define SPRN_MMUCSR0 0x3f4 /* MMU control and status register 0 */ -#define SPRN_MAS0 0x270 /* MMU Assist Register 0 */ -#define SPRN_MAS1 0x271 /* MMU Assist Register 1 */ -#define SPRN_MAS2 0x272 /* MMU Assist Register 2 */ -#define SPRN_MAS3 0x273 /* MMU Assist Register 3 */ -#define SPRN_MAS4 0x274 /* MMU Assist Register 4 */ -#define SPRN_MAS5 0x275 /* MMU Assist Register 5 */ -#define SPRN_MAS6 0x276 /* MMU Assist Register 6 */ +#define SPRN_MAS0 0x270 /* MMU Assist Register 0 */ +#define SPRN_MAS1 0x271 /* MMU Assist Register 1 */ +#define SPRN_MAS2 0x272 /* MMU Assist Register 2 */ +#define SPRN_MAS3 0x273 /* MMU Assist Register 3 */ +#define SPRN_MAS4 0x274 /* MMU Assist Register 4 */ +#define SPRN_MAS5 0x275 /* MMU Assist Register 5 */ +#define SPRN_MAS6 0x276 /* MMU Assist Register 6 */ #define SPRN_MAS7 0x3B0 /* MMU Assist Register 7 */ -#define SPRN_IVOR32 0x210 /* Interrupt Vector Offset Register 32 */ -#define SPRN_IVOR33 0x211 /* Interrupt Vector Offset Register 33 */ -#define SPRN_IVOR34 0x212 /* Interrupt Vector Offset Register 34 */ -#define SPRN_IVOR35 0x213 /* Interrupt Vector Offset Register 35 */ -#define SPRN_SPEFSCR 0x200 /* SPE & Embedded FP Status & Control */ +#define SPRN_IVOR32 0x210 /* Interrupt Vector Offset Register 32 */ +#define SPRN_IVOR33 0x211 /* Interrupt Vector Offset Register 33 */ +#define SPRN_IVOR34 0x212 /* Interrupt Vector Offset Register 34 */ +#define SPRN_IVOR35 0x213 /* Interrupt Vector Offset Register 35 */ +#define SPRN_SPEFSCR 0x200 /* SPE & Embedded FP Status & Control */ -#define SPRN_MCSRR0 0x23a /* Machine Check Save and Restore Register 0 */ -#define SPRN_MCSRR1 0x23b /* Machine Check Save and Restore Register 1 */ +#define SPRN_MCSRR0 0x23a /* Machine Check Save and Restore Register 0 */ +#define SPRN_MCSRR1 0x23b /* Machine Check Save and Restore Register 1 */ #define SPRN_BUCSR 0x3f5 /* Branch Control and Status Register */ -#define SPRN_BBEAR 0x201 /* Branch Buffer Entry Address Register */ -#define SPRN_BBTAR 0x202 /* Branch Buffer Target Address Register */ -#define SPRN_PID1 0x279 /* Process ID Register 1 */ -#define SPRN_PID2 0x27a /* Process ID Register 2 */ +#define SPRN_BBEAR 0x201 /* Branch Buffer Entry Address Register */ +#define SPRN_BBTAR 0x202 /* Branch Buffer Target Address Register */ +#define SPRN_PID1 0x279 /* Process ID Register 1 */ +#define SPRN_PID2 0x27a /* Process ID Register 2 */ #define SPRN_MCSR 0x23c /* Machine Check Syndrome register */ #define SPRN_MCAR 0x23d /* Machine Check Address register */ #ifdef CONFIG_440 @@ -471,14 +471,13 @@ #define MCSR_DCFP 0x01000000 /* D-Cache Flush Parity Error */ #define MCSR_IMPE 0x00800000 /* Imprecise Machine Check Exception */ #endif -#define ESR_ST 0x00800000 /* Store Operation */ +#define ESR_ST 0x00800000 /* Store Operation */ #if defined(CONFIG_MPC86xx) #define SPRN_MSSCR0 0x3f6 #define SPRN_MSSSR0 0x3f7 #endif - /* Short-hand versions for a number of the above SPRNs */ #define CTR SPRN_CTR /* Counter Register */ @@ -494,14 +493,14 @@ #define DBAT2U SPRN_DBAT2U /* Data BAT 2 Upper Register */ #define DBAT3L SPRN_DBAT3L /* Data BAT 3 Lower Register */ #define DBAT3U SPRN_DBAT3U /* Data BAT 3 Upper Register */ -#define DBAT4L SPRN_DBAT4L /* Data BAT 4 Lower Register */ -#define DBAT4U SPRN_DBAT4U /* Data BAT 4 Upper Register */ -#define DBAT5L SPRN_DBAT5L /* Data BAT 5 Lower Register */ -#define DBAT5U SPRN_DBAT5U /* Data BAT 5 Upper Register */ -#define DBAT6L SPRN_DBAT6L /* Data BAT 6 Lower Register */ -#define DBAT6U SPRN_DBAT6U /* Data BAT 6 Upper Register */ -#define DBAT7L SPRN_DBAT7L /* Data BAT 7 Lower Register */ -#define DBAT7U SPRN_DBAT7U /* Data BAT 7 Upper Register */ +#define DBAT4L SPRN_DBAT4L /* Data BAT 4 Lower Register */ +#define DBAT4U SPRN_DBAT4U /* Data BAT 4 Upper Register */ +#define DBAT5L SPRN_DBAT5L /* Data BAT 5 Lower Register */ +#define DBAT5U SPRN_DBAT5U /* Data BAT 5 Upper Register */ +#define DBAT6L SPRN_DBAT6L /* Data BAT 6 Lower Register */ +#define DBAT6U SPRN_DBAT6U /* Data BAT 6 Upper Register */ +#define DBAT7L SPRN_DBAT7L /* Data BAT 7 Lower Register */ +#define DBAT7U SPRN_DBAT7U /* Data BAT 7 Upper Register */ #define DBCR0 SPRN_DBCR0 /* Debug Control Register 0 */ #define DBCR1 SPRN_DBCR1 /* Debug Control Register 1 */ #define DBSR SPRN_DBSR /* Debug Status Register */ @@ -537,10 +536,10 @@ #define ICMP SPRN_ICMP /* Instruction TLB Compare Register */ #define IMISS SPRN_IMISS /* Instruction TLB Miss Register */ #define IMMR SPRN_IMMR /* PPC 860/821 Internal Memory Map Register */ -#define LDSTCR SPRN_LDSTCR /* Load/Store Control Register */ +#define LDSTCR SPRN_LDSTCR /* Load/Store Control Register */ #define L2CR SPRN_L2CR /* PPC 750 L2 control register */ #define LR SPRN_LR -#define MBAR SPRN_MBAR /* System memory base address */ +#define MBAR SPRN_MBAR /* System memory base address */ #if defined(CONFIG_MPC86xx) #define MSSCR0 SPRN_MSSCR0 #endif @@ -555,14 +554,14 @@ #define SPR1 SPRN_SPRG1 #define SPR2 SPRN_SPRG2 #define SPR3 SPRN_SPRG3 -#define SPRG0 SPRN_SPRG0 -#define SPRG1 SPRN_SPRG1 -#define SPRG2 SPRN_SPRG2 -#define SPRG3 SPRN_SPRG3 -#define SPRG4 SPRN_SPRG4 -#define SPRG5 SPRN_SPRG5 -#define SPRG6 SPRN_SPRG6 -#define SPRG7 SPRN_SPRG7 +#define SPRG0 SPRN_SPRG0 +#define SPRG1 SPRN_SPRG1 +#define SPRG2 SPRN_SPRG2 +#define SPRG3 SPRN_SPRG3 +#define SPRG4 SPRN_SPRG4 +#define SPRG5 SPRN_SPRG5 +#define SPRG6 SPRN_SPRG6 +#define SPRG7 SPRN_SPRG7 #define SRR0 SPRN_SRR0 /* Save and Restore Register 0 */ #define SRR1 SPRN_SRR1 /* Save and Restore Register 1 */ #define SRR2 SPRN_SRR2 /* Save and Restore Register 2 */ @@ -662,25 +661,25 @@ #define DCRN_DMACC0 0x0C4 /* DMA Chained Count Register 0 */ #define DCRN_DMACC1 0x0CC /* DMA Chained Count Register 1 */ #define DCRN_DMACC2 0x0D4 /* DMA Chained Count Register 2 */ -#define DCRN_DMACC3 0x0DC /* DMA Chained Count Register 3 */ -#define DCRN_DMACR0 0x0C0 /* DMA Channel Control Register 0 */ -#define DCRN_DMACR1 0x0C8 /* DMA Channel Control Register 1 */ -#define DCRN_DMACR2 0x0D0 /* DMA Channel Control Register 2 */ -#define DCRN_DMACR3 0x0D8 /* DMA Channel Control Register 3 */ -#define DCRN_DMACT0 0x0C1 /* DMA Count Register 0 */ -#define DCRN_DMACT1 0x0C9 /* DMA Count Register 1 */ -#define DCRN_DMACT2 0x0D1 /* DMA Count Register 2 */ -#define DCRN_DMACT3 0x0D9 /* DMA Count Register 3 */ -#define DCRN_DMADA0 0x0C2 /* DMA Destination Address Register 0 */ -#define DCRN_DMADA1 0x0CA /* DMA Destination Address Register 1 */ -#define DCRN_DMADA2 0x0D2 /* DMA Destination Address Register 2 */ -#define DCRN_DMADA3 0x0DA /* DMA Destination Address Register 3 */ -#define DCRN_DMASA0 0x0C3 /* DMA Source Address Register 0 */ -#define DCRN_DMASA1 0x0CB /* DMA Source Address Register 1 */ -#define DCRN_DMASA2 0x0D3 /* DMA Source Address Register 2 */ -#define DCRN_DMASA3 0x0DB /* DMA Source Address Register 3 */ -#define DCRN_DMASR 0x0E0 /* DMA Status Register */ -#define DCRN_EXIER 0x042 /* External Interrupt Enable Register */ +#define DCRN_DMACC3 0x0DC /* DMA Chained Count Register 3 */ +#define DCRN_DMACR0 0x0C0 /* DMA Channel Control Register 0 */ +#define DCRN_DMACR1 0x0C8 /* DMA Channel Control Register 1 */ +#define DCRN_DMACR2 0x0D0 /* DMA Channel Control Register 2 */ +#define DCRN_DMACR3 0x0D8 /* DMA Channel Control Register 3 */ +#define DCRN_DMACT0 0x0C1 /* DMA Count Register 0 */ +#define DCRN_DMACT1 0x0C9 /* DMA Count Register 1 */ +#define DCRN_DMACT2 0x0D1 /* DMA Count Register 2 */ +#define DCRN_DMACT3 0x0D9 /* DMA Count Register 3 */ +#define DCRN_DMADA0 0x0C2 /* DMA Destination Address Register 0 */ +#define DCRN_DMADA1 0x0CA /* DMA Destination Address Register 1 */ +#define DCRN_DMADA2 0x0D2 /* DMA Destination Address Register 2 */ +#define DCRN_DMADA3 0x0DA /* DMA Destination Address Register 3 */ +#define DCRN_DMASA0 0x0C3 /* DMA Source Address Register 0 */ +#define DCRN_DMASA1 0x0CB /* DMA Source Address Register 1 */ +#define DCRN_DMASA2 0x0D3 /* DMA Source Address Register 2 */ +#define DCRN_DMASA3 0x0DB /* DMA Source Address Register 3 */ +#define DCRN_DMASR 0x0E0 /* DMA Status Register */ +#define DCRN_EXIER 0x042 /* External Interrupt Enable Register */ #define EXIER_CIE 0x80000000 /* Critical Interrupt Enable */ #define EXIER_SRIE 0x08000000 /* Serial Port Rx Int. Enable */ #define EXIER_STIE 0x04000000 /* Serial Port Tx Int. Enable */ @@ -695,8 +694,8 @@ #define EXIER_E2IE 0x00000004 /* External Interrupt 2 Enable */ #define EXIER_E3IE 0x00000002 /* External Interrupt 3 Enable */ #define EXIER_E4IE 0x00000001 /* External Interrupt 4 Enable */ -#define DCRN_EXISR 0x040 /* External Interrupt Status Register */ -#define DCRN_IOCR 0x0A0 /* Input/Output Configuration Register */ +#define DCRN_EXISR 0x040 /* External Interrupt Status Register */ +#define DCRN_IOCR 0x0A0 /* Input/Output Configuration Register */ #define IOCR_E0TE 0x80000000 #define IOCR_E0LP 0x40000000 #define IOCR_E1TE 0x20000000 @@ -729,14 +728,13 @@ #define SVR_VER(svr) (((svr) >> 16) & 0xFFFF) /* Version field */ #define SVR_REV(svr) (((svr) >> 0) & 0xFFFF) /* Revision field */ -#define SVR_CID(svr) (((svr) >> 28) & 0x0F) /* Company or manufacturer ID */ -#define SVR_SOCOP(svr) (((svr) >> 22) & 0x3F) /* SOC integration options */ -#define SVR_SID(svr) (((svr) >> 16) & 0x3F) /* SOC ID */ -#define SVR_PROC(svr) (((svr) >> 12) & 0x0F) /* Process revision field */ -#define SVR_MFG(svr) (((svr) >> 8) & 0x0F) /* Manufacturing revision */ -#define SVR_MJREV(svr) (((svr) >> 4) & 0x0F) /* Major SOC design revision indicator */ -#define SVR_MNREV(svr) (((svr) >> 0) & 0x0F) /* Minor SOC design revision indicator */ - +#define SVR_CID(svr) (((svr) >> 28) & 0x0F) /* Company or manufacturer ID */ +#define SVR_SOCOP(svr) (((svr) >> 22) & 0x3F) /* SOC integration options */ +#define SVR_SID(svr) (((svr) >> 16) & 0x3F) /* SOC ID */ +#define SVR_PROC(svr) (((svr) >> 12) & 0x0F) /* Process revision field */ +#define SVR_MFG(svr) (((svr) >> 8) & 0x0F) /* Manufacturing revision */ +#define SVR_MJREV(svr) (((svr) >> 4) & 0x0F) /* Major SOC design revision indicator */ +#define SVR_MNREV(svr) (((svr) >> 0) & 0x0F) /* Minor SOC design revision indicator */ /* Processor Version Register */ @@ -785,10 +783,10 @@ #define PVR_440EP_RC 0x422218D4 /* 440EP rev C and 440GR rev B have same PVR */ #define PVR_440GR_RA 0x422218D3 /* 440EP rev B and 440GR rev A have same PVR */ #define PVR_440GR_RB 0x422218D4 /* 440EP rev C and 440GR rev B have same PVR */ -#define PVR_440EPX1_RA 0x216218D0 /* 440EPX rev A with Security / Kasumi */ -#define PVR_440EPX2_RA 0x216218D4 /* 440EPX rev A without Security / Kasumi */ -#define PVR_440GRX1_RA 0x216218D0 /* 440GRX rev A with Security / Kasumi */ -#define PVR_440GRX2_RA 0x216218D4 /* 440GRX rev A without Security / Kasumi */ +#define PVR_440EPX1_RA 0x216218D0 /* 440EPX rev A with Security / Kasumi */ +#define PVR_440EPX2_RA 0x216218D4 /* 440EPX rev A without Security / Kasumi */ +#define PVR_440GRX1_RA 0x216218D0 /* 440GRX rev A with Security / Kasumi */ +#define PVR_440GRX2_RA 0x216218D4 /* 440GRX rev A without Security / Kasumi */ #define PVR_440GX_RA 0x51B21850 #define PVR_440GX_RB 0x51B21851 #define PVR_440GX_RC 0x51B21892 @@ -802,9 +800,9 @@ #define PVR_440SPe_RA 0x53521890 /* 440SPe rev A without RAID 6 support */ #define PVR_440SPe_6_RB 0x53421891 /* 440SPe rev B with RAID 6 support enabled */ #define PVR_440SPe_RB 0x53521891 /* 440SPe rev B without RAID 6 support */ -#define PVR_460EX_SE_RA 0x130218A2 /* 460EX rev A with Security Engine */ +#define PVR_460EX_SE_RA 0x130218A2 /* 460EX rev A with Security Engine */ #define PVR_460EX_RA 0x130218A3 /* 460EX rev A without Security Engine */ -#define PVR_460GT_SE_RA 0x130218A0 /* 460GT rev A with Security Engine */ +#define PVR_460GT_SE_RA 0x130218A0 /* 460GT rev A with Security Engine */ #define PVR_460GT_RA 0x130218A1 /* 460GT rev A without Security Engine */ #define PVR_601 0x00010000 #define PVR_602 0x00050000 @@ -820,9 +818,9 @@ #define PVR_750 PVR_740 #define PVR_740P 0x10080000 #define PVR_750P PVR_740P -#define PVR_7400 0x000C0000 -#define PVR_7410 0x800C0000 -#define PVR_7450 0x80000000 +#define PVR_7400 0x000C0000 +#define PVR_7410 0x800C0000 +#define PVR_7450 0x80000000 #define PVR_85xx 0x80200000 #define PVR_85xx_REV1 (PVR_85xx | 0x0010) @@ -848,10 +846,10 @@ * PowerQUICC II family processors report different PVR values depending * on silicon process (HiP3, HiP4, HiP7, etc.) */ -#define PVR_8260 PVR_8240 -#define PVR_8260_HIP3 0x00810101 -#define PVR_8260_HIP4 0x80811014 -#define PVR_8260_HIP7 0x80822011 +#define PVR_8260 PVR_8240 +#define PVR_8260_HIP3 0x00810101 +#define PVR_8260_HIP4 0x80811014 +#define PVR_8260_HIP7 0x80822011 #define PVR_8260_HIP7R1 0x80822013 #define PVR_8260_HIP7RA 0x80822014 @@ -861,7 +859,6 @@ #define PVR_5200 0x80822011 #define PVR_5200B 0x80822014 - /* * System Version Register */ @@ -882,7 +879,6 @@ /* Some parts define SVR[0:23] as the SOC version */ #define SVR_SOC_VER(svr) (((svr) >> 8) & 0xFFFFFF) /* SOC Version fields */ - /* * SVR_SOC_VER() Version Values */ @@ -915,8 +911,6 @@ #define SVR_8641 0x809000 #define SVR_8641D 0x809001 - - /* I am just adding a single entry for 8260 boards. I think we may be * able to combine mbx, fads, rpxlite, bseip, and classic into a single * generic 8xx as well. The boards containing these processors are either @@ -944,7 +938,6 @@ #define _MACH_tqm8xxL 0x00010000 /* TQM8xxL */ #define _MACH_hidden_dragon 0x00020000 /* Motorola Hidden Dragon eval board */ - /* see residual.h for these */ #define _PREP_Motorola 0x01 /* motorola prep */ #define _PREP_Firm 0x02 /* firmworks prep */ @@ -1071,7 +1064,7 @@ struct thread_struct { struct pt_regs *regs; /* Pointer to saved register state */ mm_segment_t fs; /* for get_fs() validation */ void *pgdir; /* root of page-table tree */ - signed long last_syscall; + signed long last_syscall; double fpr[32]; /* Complete floating point set */ unsigned long fpscr_pad; /* fpr ... fpscr must be contiguous */ unsigned long fpscr; /* Floating point status */ @@ -1096,7 +1089,7 @@ struct thread_struct { /* * Note: the vm_start and vm_end fields here should *not* - * be in kernel space. (Could vm_end == vm_start perhaps?) + * be in kernel space. (Could vm_end == vm_start perhaps?) */ #define INIT_MMAP { &init_mm, 0, 0x1000, NULL, \ PAGE_SHARED, VM_READ | VM_WRITE | VM_EXEC, \ @@ -1126,7 +1119,7 @@ unsigned long get_wchan(struct task_struct *p); #define alloc_task_struct() \ ((struct task_struct *) __get_free_pages(GFP_KERNEL,1)) #define free_task_struct(p) free_pages((unsigned long)(p),1) -#define get_task_struct(tsk) atomic_inc(&mem_map[MAP_NR(tsk)].count) +#define get_task_struct(tsk) atomic_inc(&mem_map[MAP_NR(tsk)].count) /* in process.c - for early bootup debug -- Cort */ int ll_printk(const char *, ...); diff --git a/include/asm-sh/cache.h b/include/asm-sh/cache.h index 67474c7b44..25b409b6b0 100644 --- a/include/asm-sh/cache.h +++ b/include/asm-sh/cache.h @@ -7,28 +7,26 @@ struct __large_struct { unsigned long buf[100]; }; #define __m(x) (*(struct __large_struct *)(x)) -void dcache_wback_range(u32 start, u32 end) +void dcache_wback_range (u32 start, u32 end) { - u32 v; + u32 v; - start &= ~(L1_CACHE_BYTES-1); - for (v = start; v < end; v+=L1_CACHE_BYTES) { - asm volatile("ocbwb %0" - : /* no output */ - : "m" (__m(v))); - } + start &= ~(L1_CACHE_BYTES - 1); + for (v = start; v < end; v += L1_CACHE_BYTES) { + asm volatile ("ocbwb %0": /* no output */ + :"m" (__m (v))); + } } -void dcache_invalid_range(u32 start, u32 end) +void dcache_invalid_range (u32 start, u32 end) { - u32 v; + u32 v; - start &= ~(L1_CACHE_BYTES-1); - for (v = start; v < end; v+=L1_CACHE_BYTES) { - asm volatile("ocbi %0" - : /* no output */ - : "m" (__m(v))); - } + start &= ~(L1_CACHE_BYTES - 1); + for (v = start; v < end; v += L1_CACHE_BYTES) { + asm volatile ("ocbi %0": /* no output */ + :"m" (__m (v))); + } } #endif /* CONFIG_SH4 || CONFIG_SH4A */ diff --git a/include/asm-sparc/leon3.h b/include/asm-sparc/leon3.h index 84d0e2ed27..b90d35b198 100644 --- a/include/asm-sparc/leon3.h +++ b/include/asm-sparc/leon3.h @@ -28,10 +28,9 @@ #error Include LEON3 header file only if LEON3 processor #endif -/* Not much to define, most is Plug and Play and GRLIB dependent - * not LEON3 dependent. See for GRLIB timers, interrupt +/* Not much to define, most is Plug and Play and GRLIB dependent + * not LEON3 dependent. See for GRLIB timers, interrupt * ctrl, memory controllers etc. */ - #endif diff --git a/include/configs/grsim_leon2.h b/include/configs/grsim_leon2.h index 47f13d0bc1..2ad5b95a17 100644 --- a/include/configs/grsim_leon2.h +++ b/include/configs/grsim_leon2.h @@ -313,8 +313,8 @@ /*** LEON2 UART 1 ***/ #define CFG_LEON2_UART1_SCALER \ - ((((CONFIG_SYS_CLK_FREQ*10)/(CONFIG_BAUDRATE*8))-5)/10) - + ((((CONFIG_SYS_CLK_FREQ*10)/(CONFIG_BAUDRATE*8))-5)/10) + /* UART1 Define to 1 or 0 */ #define LEON2_UART1_LOOPBACK_ENABLE 0 #define LEON2_UART1_FLOWCTRL_ENABLE 0 @@ -324,7 +324,7 @@ /*** LEON2 UART 2 ***/ #define CFG_LEON2_UART2_SCALER \ - ((((CONFIG_SYS_CLK_FREQ*10)/(CONFIG_BAUDRATE*8))-5)/10) + ((((CONFIG_SYS_CLK_FREQ*10)/(CONFIG_BAUDRATE*8))-5)/10) /* UART2 Define to 1 or 0 */ #define LEON2_UART2_LOOPBACK_ENABLE 0 diff --git a/include/pci_ids.h b/include/pci_ids.h index 593c074793..5481fff625 100644 --- a/include/pci_ids.h +++ b/include/pci_ids.h @@ -2073,4 +2073,3 @@ #define PCI_DEVICE_ID_MPC8641 0x7010 #define PCI_DEVICE_ID_MPC8641D 0x7011 #define PCI_DEVICE_ID_MPC8610 0x7018 - diff --git a/net/bootp.c b/net/bootp.c index 0eeef57842..3c0614c5cf 100644 --- a/net/bootp.c +++ b/net/bootp.c @@ -163,21 +163,21 @@ static void BootpVendorFieldProcess (u8 * ext) switch (*ext) { /* Fixed length fields */ - case 1: /* Subnet mask */ + case 1: /* Subnet mask */ if (NetOurSubnetMask == 0) NetCopyIP (&NetOurSubnetMask, (IPaddr_t *) (ext + 2)); break; - case 2: /* Time offset - Not yet supported */ + case 2: /* Time offset - Not yet supported */ break; /* Variable length fields */ - case 3: /* Gateways list */ + case 3: /* Gateways list */ if (NetOurGatewayIP == 0) { NetCopyIP (&NetOurGatewayIP, (IPaddr_t *) (ext + 2)); } break; - case 4: /* Time server - Not yet supported */ + case 4: /* Time server - Not yet supported */ break; - case 5: /* IEN-116 name server - Not yet supported */ + case 5: /* IEN-116 name server - Not yet supported */ break; case 6: if (NetOurDNSIP == 0) { @@ -189,43 +189,43 @@ static void BootpVendorFieldProcess (u8 * ext) } #endif break; - case 7: /* Log server - Not yet supported */ + case 7: /* Log server - Not yet supported */ break; - case 8: /* Cookie/Quote server - Not yet supported */ + case 8: /* Cookie/Quote server - Not yet supported */ break; - case 9: /* LPR server - Not yet supported */ + case 9: /* LPR server - Not yet supported */ break; - case 10: /* Impress server - Not yet supported */ + case 10: /* Impress server - Not yet supported */ break; - case 11: /* RPL server - Not yet supported */ + case 11: /* RPL server - Not yet supported */ break; - case 12: /* Host name */ + case 12: /* Host name */ if (NetOurHostName[0] == 0) { size = truncate_sz ("Host Name", sizeof (NetOurHostName), size); memcpy (&NetOurHostName, ext + 2, size); NetOurHostName[size] = 0; } break; - case 13: /* Boot file size */ + case 13: /* Boot file size */ if (size == 2) NetBootFileSize = ntohs (*(ushort *) (ext + 2)); else if (size == 4) NetBootFileSize = ntohl (*(ulong *) (ext + 2)); break; - case 14: /* Merit dump file - Not yet supported */ + case 14: /* Merit dump file - Not yet supported */ break; - case 15: /* Domain name - Not yet supported */ + case 15: /* Domain name - Not yet supported */ break; - case 16: /* Swap server - Not yet supported */ + case 16: /* Swap server - Not yet supported */ break; - case 17: /* Root path */ + case 17: /* Root path */ if (NetOurRootPath[0] == 0) { size = truncate_sz ("Root Path", sizeof (NetOurRootPath), size); memcpy (&NetOurRootPath, ext + 2, size); NetOurRootPath[size] = 0; } break; - case 18: /* Extension path - Not yet supported */ + case 18: /* Extension path - Not yet supported */ /* * This can be used to send the information of the * vendor area in another file that the client can @@ -233,7 +233,7 @@ static void BootpVendorFieldProcess (u8 * ext) */ break; /* IP host layer fields */ - case 40: /* NIS Domain name */ + case 40: /* NIS Domain name */ if (NetOurNISDomain[0] == 0) { size = truncate_sz ("NIS Domain Name", sizeof (NetOurNISDomain), size); memcpy (&NetOurNISDomain, ext + 2, size); @@ -241,7 +241,7 @@ static void BootpVendorFieldProcess (u8 * ext) } break; /* Application layer fields */ - case 43: /* Vendor specific info - Not yet supported */ + case 43: /* Vendor specific info - Not yet supported */ /* * Binary information to exchange specific * product information. @@ -879,7 +879,7 @@ static void DhcpSendRequestPkt(Bootp_t *bp_offer) iplen = BOOTP_HDR_SIZE - sizeof(bp->bp_vend) + extlen; NetSetIP(iphdr, 0xFFFFFFFFL, PORT_BOOTPS, PORT_BOOTPC, iplen); - debug ("Transmitting DHCPREQUEST packet: len = %d\n", pktlen); + debug ("Transmitting DHCPREQUEST packet: len = %d\n", pktlen); #ifdef CONFIG_BOOTP_DHCP_REQUEST_DELAY udelay(CONFIG_BOOTP_DHCP_REQUEST_DELAY); #endif /* CONFIG_BOOTP_DHCP_REQUEST_DELAY */