- CFG_RX_ETH_BUFFER added.

This commit is contained in:
stroese 2003-06-05 15:39:44 +00:00
parent c602883592
commit 53cf9435cc
16 changed files with 54 additions and 36 deletions

10
README
View File

@ -690,7 +690,7 @@ The following options need to be configured:
- NETWORK Support (PCI):
CONFIG_E1000
Support for Intel 8254x gigabit chips.
CONFIG_EEPRO100
Support for Intel 82557/82559/82559ER chips.
Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
@ -1442,6 +1442,14 @@ Configuration Settings:
Define if the flash driver uses extra elements in the
common flash structure for storing flash geometry
- CFG_RX_ETH_BUFFER:
Defines the number of ethernet receive buffers. On some
ethernet controllers it is recommended to set this value
to 8 or even higher (EEPRO100 or 405 EMAC), since all
buffers can be full shortly after enabling the interface
on high ethernet traffic.
Defaults to 4 if not defined.
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
following configurations:

View File

@ -125,6 +125,10 @@
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* NAND-FLASH stuff
*-----------------------------------------------------------------------

View File

@ -144,7 +144,7 @@
/*
* NS16550 Configuration
*/
#define CFG_NS16550
#define CFG_NS16550
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
@ -171,7 +171,7 @@
* Memory configuration using SPD information stored on the SODIMMs
* not yet supported.
*/
#define CFG_SDRAM_SIZE 64 /* SDRAM size -- 64 or 128 MB supported */
/* Bit-field values for MCCR1.
@ -186,7 +186,7 @@
#else
# error "SDRAM size not supported"
#endif
#define CFG_BANK1_ROW 0
#define CFG_BANK1_ROW 0
#define CFG_BANK2_ROW 0
#define CFG_BANK3_ROW 0
#define CFG_BANK4_ROW 0
@ -361,7 +361,7 @@
/* IRQ_ENA_2 bit definitions */
#define I_ENA_2_IEAB 0x80 /* ABORT IRQ enable */
#define I_ENA_2_IEK1 0x40 /* KEY1 IRQ enable */
#define I_ENA_2_IEK2 0x20 /* KEY2 IRQ enable */
#define I_ENA_2_IEK2 0x20 /* KEY2 IRQ enable */
#define I_ENA_2_IERT 0x10 /* RTC IRQ enable */
#define I_ENA_2_IESM 0x08 /* LM81 IRQ enable */
#define I_ENA_2_IEDG 0x04 /* DEGENERATING IRQ enable */
@ -371,9 +371,9 @@
/* IRQ_STAT_2 bit definitions */
#define I_STAT_2_ABO 0x80 /* ABORT IRQ status */
#define I_STAT_2_KY1 0x40 /* KEY1 IRQ status */
#define I_STAT_2_KY2 0x20 /* KEY2 IRQ status */
#define I_STAT_2_KY2 0x20 /* KEY2 IRQ status */
#define I_STAT_2_RTC 0x10 /* RTC IRQ status */
#define I_STAT_2_SMN 0x08 /* LM81 IRQ status */
#define I_STAT_2_SMN 0x08 /* LM81 IRQ status */
#define I_STAT_2_DEG 0x04 /* DEGENERATING IRQ status */
#define I_STAT_2_SIO2 0x02 /* ST16552/B IRQ status */
#define I_STAT_2_SIO1 0x01 /* ST16552/A IRQ status */
@ -421,14 +421,14 @@
#define DISP_UDC_ADR *((volatile uchar*)(DISPLAY_BASE + 0x00)) /* UDC Address Reg. */
#define DISP_CWORD *((volatile uchar*)(DISPLAY_BASE + 0x10)) /* Control Word Reg. */
#define DISP_DIG0 *((volatile uchar*)(DISP_CHR_RAM + 0x00)) /* Digit 0 address */
#define DISP_DIG1 *((volatile uchar*)(DISP_CHR_RAM + 0x01)) /* Digit 0 address */
#define DISP_DIG0 *((volatile uchar*)(DISP_CHR_RAM + 0x00)) /* Digit 0 address */
#define DISP_DIG1 *((volatile uchar*)(DISP_CHR_RAM + 0x01)) /* Digit 0 address */
#define DISP_DIG2 *((volatile uchar*)(DISP_CHR_RAM + 0x02)) /* Digit 0 address */
#define DISP_DIG3 *((volatile uchar*)(DISP_CHR_RAM + 0x03)) /* Digit 0 address */
#define DISP_DIG4 *((volatile uchar*)(DISP_CHR_RAM + 0x04)) /* Digit 0 address */
#define DISP_DIG3 *((volatile uchar*)(DISP_CHR_RAM + 0x03)) /* Digit 0 address */
#define DISP_DIG4 *((volatile uchar*)(DISP_CHR_RAM + 0x04)) /* Digit 0 address */
#define DISP_DIG5 *((volatile uchar*)(DISP_CHR_RAM + 0x05)) /* Digit 0 address */
#define DISP_DIG6 *((volatile uchar*)(DISP_CHR_RAM + 0x06)) /* Digit 0 address */
#define DISP_DIG7 *((volatile uchar*)(DISP_CHR_RAM + 0x07)) /* Digit 0 address */
#define DISP_DIG6 *((volatile uchar*)(DISP_CHR_RAM + 0x06)) /* Digit 0 address */
#define DISP_DIG7 *((volatile uchar*)(DISP_CHR_RAM + 0x07)) /* Digit 0 address */
/*-----------------------------------------------------------------------
@ -441,6 +441,7 @@
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define PCI_ENET0_IOADDR 0x00104000
#define PCI_ENET0_MEMADDR 0x82000000

View File

@ -146,6 +146,8 @@
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------

View File

@ -55,15 +55,7 @@
#endif
#undef CONFIG_BOOTARGS
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
"bootm ffc00000 ffca0000"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
"bootm ffc00000"
#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
#define CONFIG_BOOTCOMMAND "bootm 100000" /* default boot command */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
@ -73,12 +65,7 @@
#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
#if 0 /* test-only */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_VENDOREX)
#else
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT)
#endif
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
@ -147,6 +134,8 @@
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
@ -202,7 +191,7 @@
#define CFG_FLASH_BASE 0xFFFC0000
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
/*
* For booting Linux, the board info and command line data
@ -360,7 +349,7 @@
#define CFG_FPGA_STATUS_TS_IRQ 0x1000
#define CFG_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
#define CFG_FPGA_MAX_SIZE 64*1024 /* 64kByte is enough for XC2S15 */
#define CFG_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S30 */
/* FPGA program pin configuration */
#define CFG_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */

View File

@ -304,6 +304,7 @@
#define CFG_ETH_IOBASE 0x00104000
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define PCI_ENET0_IOADDR 0x00104000
#define PCI_ENET0_MEMADDR 0x80000000
#endif /* __CONFIG_H */

View File

@ -333,6 +333,7 @@
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_EEPRO100_SROM_WRITE
#endif /* __CONFIG_H */

View File

@ -94,6 +94,7 @@
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100 /* Ethernet Express PRO 100 */
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define PCI_ENET0_IOADDR 0x80000000
#define PCI_ENET0_MEMADDR 0x80000000

View File

@ -261,6 +261,7 @@
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_TULIP
#endif /* __CONFIG_H */

View File

@ -263,6 +263,7 @@
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_TULIP

View File

@ -316,6 +316,7 @@
#ifdef CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#endif
/*

View File

@ -128,6 +128,10 @@
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------

View File

@ -82,6 +82,7 @@
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define PCI_ENET0_IOADDR 0x80000000
#define PCI_ENET0_MEMADDR 0x80000000

View File

@ -81,6 +81,7 @@
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NATSEMI
#define CONFIG_NS8382X

View File

@ -36,7 +36,7 @@
#define CONFIG_X86 1 /* This is a X86 CPU */
#define CONFIG_SC520 1 /* Include support for AMD SC520 */
#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
#define CFG_SDRAM_PRECHARGE_DELAY 6 /* 6T */
#define CFG_SDRAM_REFRESH_RATE 78 /* 7.8uS (choices are 7.8, 15.6, 31.2 or 62.5uS) */
#define CFG_SDRAM_RAS_CAS_DELAY 3 /* 3T */
@ -71,7 +71,7 @@
#define CONFIG_BOOTDELAY 15
#define CONFIG_BOOTARGS "root=/dev/mtdblock1 console=ttyS0,9600 mtdparts=phys:7936k(root),256k(uboot) "
#define CONFIG_BOOTCOMMAND "setenv bootargs root=/dev/nfs ip=autoconf console=ttyS0,9600 mtdparts=phys:7808k(root),128k(env),256k(uboot); bootp; bootm"
#define CONFIG_BOOTCOMMAND "setenv bootargs root=/dev/nfs ip=autoconf console=ttyS0,9600 mtdparts=phys:7808k(root),128k(env),256k(uboot); bootp; bootm"
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
@ -123,7 +123,7 @@
#define CONFIG_SPI_EEPROM /* SPI EEPROMs such as AT25010 or AT25640 */
#define CONFIG_MW_EEPROM /* MicroWire EEPROMS such as AT93LC46 */
#define CONFIG_DS1722 /* Dallas DS1722 SPI Temperature probe */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
@ -131,7 +131,7 @@
#if 0
/* Environment in flash */
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_IS_IN_FLASH 1
# define CFG_ENV_ADDR (0x387a0000) /* Addr of Environment Sector */
# define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector (or 0x10000) */
# define CFG_ENV_OFFSET 0
@ -143,7 +143,7 @@
# define CONFIG_SPI
# define CONFIG_SPI_X 1
# define CFG_ENV_SIZE 0x2000 /* Total Size of Environment EEPROM */
# define CFG_ENV_OFFSET 0x1c00
# define CFG_ENV_OFFSET 0x1c00
#endif
@ -155,6 +155,7 @@
*/
#define CONFIG_NET_MULTI /* Multi ethernet cards support */
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
/************************************************************
* IDE/ATA stuff
@ -204,8 +205,8 @@
#define CONFIG_PCI_SCAN_SHOW
#define CFG_FIRST_PCI_IRQ 9
#define CFG_SECOND_PCI_IRQ 10
#define CFG_THIRD_PCI_IRQ 11
#define CFG_SECOND_PCI_IRQ 10
#define CFG_THIRD_PCI_IRQ 11
#define CFG_FORTH_PCI_IRQ 12

View File

@ -125,6 +125,7 @@ protect on $(u-boot_startaddr) $(u-boot_endaddr)"
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_NET_MULTI
#define CONFIG_EEPRO100
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_EEPRO100_SROM_WRITE
#define PCI_ENET0_IOADDR 0xF0000000