From 7054cfda6501d67b6796fb1b140655fe2b91aed5 Mon Sep 17 00:00:00 2001 From: Albert Aribaud <[albert.aribaud@free.fr]> Date: Thu, 16 Sep 2010 20:30:30 +0530 Subject: [PATCH 1/6] mvsata_ide: adjust port init sequence mvsata_ide_initialize_port(): adjust init sequence (SStatus should be checked only after all writes to SControl) and return success/failure to ide_preinit(). Also, as some tests showed init durations in the hundreds of us, raise the time-out to 01 ms to be on the safe side. Signed-off-by: Albert Aribaud --- drivers/block/mvsata_ide.c | 42 ++++++++++++++++++++++++++++++-------- 1 file changed, 33 insertions(+), 9 deletions(-) diff --git a/drivers/block/mvsata_ide.c b/drivers/block/mvsata_ide.c index 077b2789bb..3d6993ac2a 100644 --- a/drivers/block/mvsata_ide.c +++ b/drivers/block/mvsata_ide.c @@ -90,6 +90,18 @@ struct mvsata_port_registers { #define MVSATA_SSTATUS_DET_MASK 0x0000000F #define MVSATA_SSTATUS_DET_DEVCOMM 0x00000003 +/* + * Status codes to return to client callers. Currently, callers ignore + * exact value and only care for zero or nonzero, so no need to make this + * public, it is only #define'd for clarity. + * If/when standard negative codes are implemented in U-boot, then these + * #defines should be moved to, or replaced by ones from, the common list + * of status codes. + */ + +#define MVSATA_STATUS_OK 0 +#define MVSATA_STATUS_TIMEOUT -1 + /* * Initialize one MVSATAHC port: set SControl's IPM to "always active" * and DET to "reset", then wait for SStatus's DET to become "device and @@ -97,23 +109,30 @@ struct mvsata_port_registers { * DET back to "no action". */ -static void mvsata_ide_initialize_port(struct mvsata_port_registers *port) +static int mvsata_ide_initialize_port(struct mvsata_port_registers *port) { u32 control; u32 status; - u32 tout = 50; /* wait at most 50 us for SATA reset to complete */ + u32 timeleft = 10000; /* wait at most 10 ms for SATA reset to complete */ + /* Set control IPM to 3 (no low power) and DET to 1 (initialize) */ control = readl(&port->scontrol); control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_INIT; writel(control, &port->scontrol); - while (--tout) { + /* Toggle control DET back to 0 (normal operation) */ + control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE; + writel(control, &port->scontrol); + /* wait for status DET to become 3 (device and communication OK) */ + while (--timeleft) { status = readl(&port->sstatus) & MVSATA_SSTATUS_DET_MASK; if (status == MVSATA_SSTATUS_DET_DEVCOMM) break; udelay(1); } - control = (control & ~MVSATA_SCONTROL_MASK) | MVSATA_PORT_USE; - writel(control, &port->scontrol); + /* return success or time-out error depending on time left */ + if (!timeleft) + return MVSATA_STATUS_TIMEOUT; + return MVSATA_STATUS_OK; } /* @@ -123,18 +142,23 @@ static void mvsata_ide_initialize_port(struct mvsata_port_registers *port) int ide_preinit(void) { + int status; /* Enable ATA port 0 (could be SATA port 0 or 1) if declared */ #if defined(CONFIG_SYS_ATA_IDE0_OFFSET) - mvsata_ide_initialize_port( + status = mvsata_ide_initialize_port( (struct mvsata_port_registers *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE0_OFFSET)); + if (status) + return status; #endif /* Enable ATA port 1 (could be SATA port 0 or 1) if declared */ #if defined(CONFIG_SYS_ATA_IDE1_OFFSET) - mvsata_ide_initialize_port( + status = mvsata_ide_initialize_port( (struct mvsata_port_registers *) (CONFIG_SYS_ATA_BASE_ADDR + CONFIG_SYS_ATA_IDE1_OFFSET)); + if (status) + return status; #endif - /* return 0 as we always succeed */ - return 0; + /* return success if all ports initializations succeeded */ + return MVSATA_STATUS_OK; } From 35883cca8a7f3e2ef0bcbe14d52ef9e9b2b1ab81 Mon Sep 17 00:00:00 2001 From: Prafulla Wadaskar <[prafulla@marvell.com]> Date: Mon, 20 Sep 2010 17:19:42 +0530 Subject: [PATCH 2/6] Kirkwood: print_cpuinfo fixed for valid devid revid Earlier Device Identification register was used to detect the type for SoC, considering 88F6282 support to be added, It is not possible to detect the same using current algorithm. With this patch, device ID is being read using PCIE devid register, also valid chip revision ID will also be read and displayed Signed-off-by: Prafulla Wadaskar --- arch/arm/cpu/arm926ejs/kirkwood/cpu.c | 40 +++++++++++++++--------- arch/arm/include/asm/arch-kirkwood/cpu.h | 2 ++ 2 files changed, 28 insertions(+), 14 deletions(-) diff --git a/arch/arm/cpu/arm926ejs/kirkwood/cpu.c b/arch/arm/cpu/arm926ejs/kirkwood/cpu.c index 82c978bd93..b4a4c0428f 100644 --- a/arch/arm/cpu/arm926ejs/kirkwood/cpu.c +++ b/arch/arm/cpu/arm926ejs/kirkwood/cpu.c @@ -54,10 +54,11 @@ unsigned char get_random_hex(void) u8 outbuf[BUFLEN]; /* - * in case of 88F6281/88F6192 A0, + * in case of 88F6281/88F6282/88F6192 A0, * Bit7 need to reset to generate random values in KW_REG_UNDOC_0x1470 - * Soc reg offsets KW_REG_UNDOC_0x1470 and KW_REG_UNDOC_0x1478 are reserved regs and - * Does not have names at this moment (no errata available) + * Soc reg offsets KW_REG_UNDOC_0x1470 and KW_REG_UNDOC_0x1478 are + * reserved regs and does not have names at this moment + * (no errata available) */ writel(readl(KW_REG_UNDOC_0x1478) & ~(1 << 7), KW_REG_UNDOC_0x1478); for (i = 0; i < BUFLEN; i++) { @@ -271,20 +272,31 @@ static void kw_sysrst_check(void) #if defined(CONFIG_DISPLAY_CPUINFO) int print_cpuinfo(void) { - char *name = "Unknown"; + char *rev; + u16 devid = (readl(KW_REG_PCIE_DEVID) >> 16) & 0xffff; + u8 revid = readl(KW_REG_PCIE_REVID) & 0xff; - switch (readl(KW_REG_DEVICE_ID) & 0x03) { - case 1: - name = "88F6192_A0"; - break; - case 2: - name = "88F6281_A0"; - break; - default: - printf("SoC: Unsupported Kirkwood\n"); + if ((readl(KW_REG_DEVICE_ID) & 0x03) > 2) { + printf("Error.. %s:Unsupported Kirkwood SoC 88F%04x\n", __FUNCTION__, devid); return -1; } - printf("SoC: Kirkwood %s\n", name); + + switch (revid) { + case 0: + rev = "Z0"; + break; + case 2: + rev = "A0"; + break; + case 3: + rev = "A1"; + break; + default: + rev = "??"; + break; + } + + printf("SoC: Kirkwood 88F%04x_%s\n", devid, rev); return 0; } #endif /* CONFIG_DISPLAY_CPUINFO */ diff --git a/arch/arm/include/asm/arch-kirkwood/cpu.h b/arch/arm/include/asm/arch-kirkwood/cpu.h index b3022a3780..d28c51a9b6 100644 --- a/arch/arm/include/asm/arch-kirkwood/cpu.h +++ b/arch/arm/include/asm/arch-kirkwood/cpu.h @@ -35,6 +35,8 @@ #define KWGBE_PORT_SERIAL_CONTROL1_REG(_x) \ ((_x ? KW_EGIGA0_BASE : KW_EGIGA1_BASE) + 0x44c) +#define KW_REG_PCIE_DEVID (KW_REG_PCIE_BASE + 0x00) +#define KW_REG_PCIE_REVID (KW_REG_PCIE_BASE + 0x08) #define KW_REG_DEVICE_ID (KW_MPP_BASE + 0x34) #define KW_REG_SYSRST_CNT (KW_MPP_BASE + 0x50) #define SYSRST_CNT_1SEC_VAL (25*1000000) From 3b467ec4442b0d26e1f037a51cc2cbf75f37e932 Mon Sep 17 00:00:00 2001 From: Albert Aribaud <[albert.aribaud@free.fr]> Date: Thu, 7 Oct 2010 20:19:53 +0530 Subject: [PATCH 3/6] orion5x: optimize window size computation Signed-off-by: Chris Moore Signed-off-by: Albert Aribaud --- arch/arm/cpu/arm926ejs/orion5x/cpu.c | 32 ++++++++++++++++++---------- 1 file changed, 21 insertions(+), 11 deletions(-) diff --git a/arch/arm/cpu/arm926ejs/orion5x/cpu.c b/arch/arm/cpu/arm926ejs/orion5x/cpu.c index c36d7bfef8..1894b52fbf 100644 --- a/arch/arm/cpu/arm926ejs/orion5x/cpu.c +++ b/arch/arm/cpu/arm926ejs/orion5x/cpu.c @@ -48,24 +48,34 @@ void reset_cpu(unsigned long ignored) } /* - * Window Size + * Compute Window Size field value from size expressed in bytes * Used with the Base register to set the address window size and location. * Must be programmed from LSB to MSB as sequence of ones followed by * sequence of zeros. The number of ones specifies the size of the window in - * 64 KByte granularity (e.g., a value of 0x00FF specifies 256 = 16 MByte). - * NOTE: A value of 0x0 specifies 64-KByte size. + * 64 KiB granularity (e.g., a value of 0x00FF specifies 256 = 16 MiB). + * NOTES: + * 1) A sizeval equal to 0x0 specifies 4 GiB. + * 2) A return value of 0x0 specifies 64 KiB. */ unsigned int orion5x_winctrl_calcsize(unsigned int sizeval) { - int i; - unsigned int j = 0; - u32 val = sizeval >> 1; + /* + * Calculate the number of 64 KiB blocks needed minus one (rounding up). + * For sizeval > 0 this is equivalent to: + * sizeval = (u32) ceil((double) sizeval / 65536.0) - 1 + */ + sizeval = (sizeval - 1) >> 16; - for (i = 0; val >= 0x10000; i++) { - j |= (1 << i); - val = val >> 1; - } - return 0x0000ffff & j; + /* + * Propagate 'one' bits to the right by 'oring' them. + * We need only treat bits 15-0. + */ + sizeval |= sizeval >> 1; /* 'Or' bit 15 onto bit 14 */ + sizeval |= sizeval >> 2; /* 'Or' bits 15-14 onto bits 13-12 */ + sizeval |= sizeval >> 4; /* 'Or' bits 15-12 onto bits 11-8 */ + sizeval |= sizeval >> 8; /* 'Or' bits 15-8 onto bits 7-0*/ + + return sizeval; } /* From 6edf0f121f7c681ef32bf02c2c71feb8fd8e304d Mon Sep 17 00:00:00 2001 From: Prafulla Wadaskar Date: Thu, 30 Sep 2010 19:33:19 +0530 Subject: [PATCH 4/6] Kirkwood: dram_init is moved to dram.c For all Kirkwood boards so far dram_init function is duplicated dram_init function is moved to dram.c and relevant code from all board specific files removed If any board needs specific dram init handling than standard one, then, a macro CONFIG_SYS_BOARD_DRAM_INIT should be defined in board config header file and the dram_init function can be put in board specific source file For ex. keymile boards Signed-off-by: Prafulla Wadaskar --- arch/arm/cpu/arm926ejs/kirkwood/dram.c | 38 +++++++++++++++++++ board/Marvell/guruplug/guruplug.c | 11 ------ .../Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c | 11 ------ board/Marvell/openrd_base/openrd_base.c | 11 ------ board/Marvell/rd6281a/rd6281a.c | 11 ------ board/Marvell/sheevaplug/sheevaplug.c | 11 ------ include/configs/keymile-common.h | 1 + 7 files changed, 39 insertions(+), 55 deletions(-) diff --git a/arch/arm/cpu/arm926ejs/kirkwood/dram.c b/arch/arm/cpu/arm926ejs/kirkwood/dram.c index 8f2a18af6b..7439c87f68 100644 --- a/arch/arm/cpu/arm926ejs/kirkwood/dram.c +++ b/arch/arm/cpu/arm926ejs/kirkwood/dram.c @@ -23,8 +23,11 @@ */ #include +#include #include +DECLARE_GLOBAL_DATA_PTR; + #define KW_REG_CPUCS_WIN_BAR(x) (KW_REGISTER(0x1500) + (x * 0x08)) #define KW_REG_CPUCS_WIN_SZ(x) (KW_REGISTER(0x1504) + (x * 0x08)) /* @@ -56,3 +59,38 @@ u32 kw_sdram_bs(enum memory_bank bank) result += 0x01000000; return result; } + +#ifndef CONFIG_SYS_BOARD_DRAM_INIT +int dram_init(void) +{ + int i; + + gd->ram_size = 0; + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + gd->bd->bi_dram[i].start = kw_sdram_bar(i); + gd->bd->bi_dram[i].size = kw_sdram_bs(i); + /* + * It is assumed that all memory banks are consecutive + * and without gaps. + * If the gap is found, ram_size will be reported for + * consecutive memory only + */ + if (gd->bd->bi_dram[i].start != gd->ram_size) + break; + + gd->ram_size += gd->bd->bi_dram[i].size; + + } + return 0; +} + +/* + * If this function is not defined here, + * board.c alters dram bank zero configuration defined above. + */ +void dram_init_banksize(void) +{ + dram_init(); +} +#endif /* CONFIG_SYS_BOARD_DRAM_INIT */ + diff --git a/board/Marvell/guruplug/guruplug.c b/board/Marvell/guruplug/guruplug.c index c028a53bcb..4df4e9b260 100644 --- a/board/Marvell/guruplug/guruplug.c +++ b/board/Marvell/guruplug/guruplug.c @@ -108,17 +108,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - #ifdef CONFIG_RESET_PHY_R void mv_phy_88e1121_init(char *name) { diff --git a/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c b/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c index c959bf879e..93d1400be4 100644 --- a/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c +++ b/board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c @@ -110,17 +110,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - #ifdef CONFIG_MV88E61XX_SWITCH void reset_phy(void) { diff --git a/board/Marvell/openrd_base/openrd_base.c b/board/Marvell/openrd_base/openrd_base.c index c00a08aeab..d006b2ddf7 100644 --- a/board/Marvell/openrd_base/openrd_base.c +++ b/board/Marvell/openrd_base/openrd_base.c @@ -113,17 +113,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - #ifdef CONFIG_RESET_PHY_R /* Configure and enable MV88E1116 PHY */ void reset_phy(void) diff --git a/board/Marvell/rd6281a/rd6281a.c b/board/Marvell/rd6281a/rd6281a.c index 8713a3cf9b..0d76146b65 100644 --- a/board/Marvell/rd6281a/rd6281a.c +++ b/board/Marvell/rd6281a/rd6281a.c @@ -109,17 +109,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - void mv_phy_88e1116_init(char *name) { u16 reg; diff --git a/board/Marvell/sheevaplug/sheevaplug.c b/board/Marvell/sheevaplug/sheevaplug.c index 547126af8f..173a7b809d 100644 --- a/board/Marvell/sheevaplug/sheevaplug.c +++ b/board/Marvell/sheevaplug/sheevaplug.c @@ -108,17 +108,6 @@ int board_init(void) return 0; } -int dram_init(void) -{ - int i; - - for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { - gd->bd->bi_dram[i].start = kw_sdram_bar(i); - gd->bd->bi_dram[i].size = kw_sdram_bs(i); - } - return 0; -} - #ifdef CONFIG_RESET_PHY_R /* Configure and enable MV88E1116 PHY */ void reset_phy(void) diff --git a/include/configs/keymile-common.h b/include/configs/keymile-common.h index 6c14ca00c5..62d21f6286 100644 --- a/include/configs/keymile-common.h +++ b/include/configs/keymile-common.h @@ -85,6 +85,7 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_BOARD_DRAM_INIT /* Used board specific dram_init */ /* * How to get access to the slot ID. Put this here to make it easy From 44f1ec6c5e9c4ed833abe7ce4c266e4e6266493c Mon Sep 17 00:00:00 2001 From: Prafulla Wadaskar Date: Thu, 30 Sep 2010 22:53:43 +0530 Subject: [PATCH 5/6] kirkwood: added common config file mv-common.h It is observed that, in most of the board configs the code is being duplicated, also for any common change all board files needs update This issue was under discussion from long on mailing list and we converge on introducing common config file. With this patch- 1. Total Kirkwood specific configuration code is reduced by 210 lines 2. All common configuration can be shared by multiple boards 3. Easy to manage common updates like ARM relocation changes mv-common.h file is added to include/configs/ It contains all common configuration supported for all Kirkwood boards The respective board configs are updated for its usage Build tested for guruplug, mv88f6281gtw_ge, openrd_base, rd6281a and sheevaplug Binary execution tested for sheevaplug Todo: 1. Other custom Kirkwood boards to be synced 2. The support to be extended for Orion5X based boards Signed-off-by: Prafulla Wadaskar --- include/configs/guruplug.h | 103 ++------------ include/configs/mv-common.h | 225 ++++++++++++++++++++++++++++++ include/configs/mv88f6281gtw_ge.h | 120 ++-------------- include/configs/openrd_base.h | 146 ++----------------- include/configs/rd6281a.h | 101 ++------------ include/configs/sheevaplug.h | 104 +------------- 6 files changed, 266 insertions(+), 533 deletions(-) create mode 100644 include/configs/mv-common.h diff --git a/include/configs/guruplug.h b/include/configs/guruplug.h index eb3fa57d67..2c2682cfad 100644 --- a/include/configs/guruplug.h +++ b/include/configs/guruplug.h @@ -33,58 +33,12 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_GURUPLUG /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ @@ -96,18 +50,13 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -142,56 +91,20 @@ "x_bootargs=console=ttyS0,115200\0" \ "x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0" -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */ -#define CONFIG_SYS_MEMTEST_END 0x1fffffff /*(_512M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_CMD_MII -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ #define CONFIG_PHY_BASE_ADR 0 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv88e1121 PHY */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI + * SATA Driver configuration */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #define CONFIG_SYS_ALT_MEMTEST diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h new file mode 100644 index 0000000000..e78d29f832 --- /dev/null +++ b/include/configs/mv-common.h @@ -0,0 +1,225 @@ +/* + * (C) Copyright 2010 + * Marvell Semiconductor + * Written-by: Prafulla Wadaskar + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301 USA + */ + +/* + * This file contains Marvell Board Specific common defincations. + * This file should be included in board config header file. + * + * It supports common definations for Kirkwood platform + * TBD: support for Orion5X platforms + */ + +#ifndef _MV_COMMON_H +#define _MV_COMMON_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_MARVELL 1 +#define CONFIG_ARM926EJS 1 /* Basic Architecture */ + +#if defined(CONFIG_KIRKWOOD) +#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ +#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ +#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ +#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ + +#define CONFIG_I2C_MVTWSI_BASE KW_TWSI_BASE +#define MV_UART0_BASE KW_UART0_BASE +#define MV_SATA_BASE KW_SATA_BASE +#define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET +#define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET + +#else +#error "Unsupported SoC" +#endif + +/* + * CLKs configurations + */ +#define CONFIG_SYS_HZ 1000 + +/* + * NS16550 Configuration + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK +#define CONFIG_SYS_NS16550_COM1 MV_UART0_BASE + +/* + * Serial Port configuration + * The following definitions let you select what serial you want to use + * for your console driver. + */ + +#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ + 115200,230400, 460800, 921600 } +/* auto boot */ +#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ +#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ + +#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ + +/* + * NAND configuration + */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_KIRKWOOD +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */ +#define NAND_ALLOW_ERASE_ALL 1 +#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ +#endif + +/* + * SPI Flash configuration + */ +#ifdef CONFIG_CMD_SF +#define CONFIG_SPI_FLASH 1 +#define CONFIG_HARD_SPI 1 +#define CONFIG_KIRKWOOD_SPI 1 +#define CONFIG_SPI_FLASH_MACRONIX 1 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */ +#endif + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */ +/* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +/* + * Other required minimal configurations + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ +#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ +#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ +#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ +#define CONFIG_NR_DRAM_BANKS 4 +#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ +#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ +#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ +#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ +#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ + +/* + * Ethernet Driver configuration + */ +#ifdef CONFIG_CMD_NET +#define CONFIG_CMD_MII +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_NET_MULTI /* specify more that one ports available */ +#define CONFIG_MII /* expose smi ove miiphy interface */ +#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ +#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ +#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ +#endif /* CONFIG_CMD_NET */ + +/* + * USB/EHCI + */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI /* Enable EHCI USB support */ +#define CONFIG_USB_EHCI_KIRKWOOD +#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION +#define CONFIG_SUPPORT_VFAT +#endif /* CONFIG_CMD_USB */ + +/* + * IDE Support on SATA ports + */ +#ifdef CONFIG_CMD_IDE +#define __io +#define CONFIG_CMD_EXT2 +#define CONFIG_MVSATA_IDE +#define CONFIG_IDE_PREINIT +#define CONFIG_MVSATA_IDE_USE_PORT1 +/* Needs byte-swapping for ATA data register */ +#define CONFIG_IDE_SWAP_IO +/* Data, registers and alternate blocks are at the same offset */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) +#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) +/* Each 8-bit ATA register is aligned to a 4-bytes address */ +#define CONFIG_SYS_ATA_STRIDE 4 +/* Controller supports 48-bits LBA addressing */ +#define CONFIG_LBA48 +/* CONFIG_CMD_IDE requires some #defines for ATA registers */ +#define CONFIG_SYS_IDE_MAXBUS 2 +#define CONFIG_SYS_IDE_MAXDEVICE 2 +/* ATA registers base is at SATA controller base */ +#define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE +#endif /* CONFIG_CMD_IDE */ + +/* + * I2C related stuff + */ +#ifdef CONFIG_CMD_I2C +#define CONFIG_I2C_MVTWSI +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_SYS_I2C_SPEED 100000 +#endif + +/* + * File system + */ +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_RBTREE +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_LZO + +#endif /* _MV_COMMON_H */ diff --git a/include/configs/mv88f6281gtw_ge.h b/include/configs/mv88f6281gtw_ge.h index 9ef03a68b7..d3238295f2 100644 --- a/include/configs/mv88f6281gtw_ge.h +++ b/include/configs/mv88f6281gtw_ge.h @@ -33,66 +33,19 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_MV88F6281GTW_GE /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ #include -#define CONFIG_CMD_AUTOSCRIPT #define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING #define CONFIG_CMD_ENV #define CONFIG_CMD_FAT #define CONFIG_CMD_PING @@ -100,17 +53,18 @@ #define CONFIG_CMD_USB /* - * Flash configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_SF -#define CONFIG_SPI_FLASH 1 -#define CONFIG_HARD_SPI 1 -#define CONFIG_KIRKWOOD_SPI 1 -#define CONFIG_SPI_FLASH_MACRONIX 1 -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */ -#endif +#include "mv-common.h" + +/* Unwanted stuffs from mv-common.h */ +#undef CONFIG_CMD_EXT2 +#undef CONFIG_CMD_JFFS2 +#undef CONFIG_CMD_FAT +#undef CONFIG_CMD_UBI +#undef CONFIG_CMD_UBIFS +#undef CONFIG_RBTREE /* * Environment variables configurations @@ -141,60 +95,12 @@ "x_bootcmd_usb=usb start\0" \ "x_bootargs_root=root=/dev/mtdblock3 ro rootfstype=squashfs\0" -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PING -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ +#define CONFIG_MV88E61XX_SWITCH /* Enable mv88e61xx switch driver */ #endif /* CONFIG_CMD_NET */ -/* - * Marvell 88Exxxx Switch configurations - */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init phy/swtich */ -#define CONFIG_MV88E61XX_SWITCH /* Enable mv88e61xx switch driver */ - -/* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ - #endif /* _CONFIG_MV88F6281GTW_GE_H */ diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h index 846dfcd484..cfdd09cda0 100644 --- a/include/configs/openrd_base.h +++ b/include/configs/openrd_base.h @@ -38,59 +38,12 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_OPENRD_BASE /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ -#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ @@ -106,15 +59,10 @@ #define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -153,98 +101,20 @@ "mtdids="MTDIDS_DEFAULT"\0" \ "mtdparts="MTDPARTS_DEFAULT"\0" -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_AUTO_COMPLETE -#define CONFIG_CMDLINE_EDITING -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0x8 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI + * SATA Driver configuration */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ - -/* - * IDe Support on SATA port0 - */ -#ifdef CONFIG_CMD_IDE -#define __io -#define CONFIG_CMD_EXT2 -#define CONFIG_MVSATA_IDE -#define CONFIG_IDE_PREINIT -#define CONFIG_MVSATA_IDE_USE_PORT1 -/* Needs byte-swapping for ATA data register */ -#define CONFIG_IDE_SWAP_IO -/* Data, registers and alternate blocks are at the same offset */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) -#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) -#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) -/* Each 8-bit ATA register is aligned to a 4-bytes address */ -#define CONFIG_SYS_ATA_STRIDE 4 -/* Controller supports 48-bits LBA addressing */ -#define CONFIG_LBA48 -/* CONFIG_CMD_IDE requires some #defines for ATA registers */ -#define CONFIG_SYS_IDE_MAXBUS 2 -#define CONFIG_SYS_IDE_MAXDEVICE 2 -/* ATA registers base is at SATA controller base */ -#define CONFIG_SYS_ATA_BASE_ADDR KW_SATA_BASE -/* ATA bus 0 is Kirkwood port 0 on openrd */ -#define CONFIG_SYS_ATA_IDE0_OFFSET KW_SATA_PORT0_OFFSET -/* ATA bus 1 is Kirkwood port 1 on openrd */ -#define CONFIG_SYS_ATA_IDE1_OFFSET KW_SATA_PORT1_OFFSET -#endif /* CONFIG_CMD_IDE */ - -/* - * File system - */ -#define CONFIG_CMD_FAT -#define CONFIG_CMD_UBI -#define CONFIG_CMD_UBIFS -#define CONFIG_RBTREE -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_MTD_PARTITIONS -#define CONFIG_CMD_MTDPARTS -#define CONFIG_LZO +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #endif /* _CONFIG_OPENRD_BASE_H */ diff --git a/include/configs/rd6281a.h b/include/configs/rd6281a.h index 585730111f..60f957996c 100644 --- a/include/configs/rd6281a.h +++ b/include/configs/rd6281a.h @@ -33,58 +33,12 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_RD6281A /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ @@ -97,17 +51,13 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB +#define CONFIG_CMD_IDE /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -142,57 +92,24 @@ "x_bootcmd_usb=usb start\0" \ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0" -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ #define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */ #define CONFIG_MV88E61XX_MULTICHIP_ADRMODE #define CONFIG_DIS_AUTO_NEG_SPEED_GMII /*Disable Auto speed negociation */ #define CONFIG_PHY_SPEED _1000BASET /*Force PHYspeed to 1GBPs */ #define CONFIG_PHY_BASE_ADR 0x0A -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init switch and PHY */ #define CONFIG_MV88E61XX_SWITCH /* Enable MV88E61XX switch driver */ #endif /* CONFIG_CMD_NET */ /* - * USB/EHCI + * SATA Driver configuration */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ +#ifdef CONFIG_MVSATA_IDE +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET +#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET +#endif /*CONFIG_MVSATA_IDE*/ #endif /* _CONFIG_RD6281A_H */ diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h index c5de86eb03..83dd8ff08f 100644 --- a/include/configs/sheevaplug.h +++ b/include/configs/sheevaplug.h @@ -33,82 +33,28 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_MARVELL 1 -#define CONFIG_ARM926EJS 1 /* Basic Architecture */ #define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ #define CONFIG_KIRKWOOD 1 /* SOC Family Name */ #define CONFIG_KW88F6281 1 /* SOC Name */ #define CONFIG_MACH_SHEEVAPLUG /* Machine type */ - -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ - -/* - * CLKs configurations - */ -#define CONFIG_SYS_HZ 1000 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ - 115200,230400, 460800, 921600 } -/* auto boot */ -#define CONFIG_BOOTDELAY 3 /* default enable autoboot */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ -#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ - -#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ /* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ #include -#define CONFIG_CMD_AUTOSCRIPT #define CONFIG_CMD_DHCP #define CONFIG_CMD_ENV #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB - /* - * NAND configuration + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define NAND_MAX_CHIPS 1 -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif +#include "mv-common.h" /* * Environment variables configurations @@ -143,58 +89,14 @@ "x_bootcmd_usb=usb start\0" \ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0" -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1 MiB for malloc() */ -/* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 - -/* - * Other required minimal configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_AUTO_COMPLETE -#define CONFIG_CMDLINE_EDITING -#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */ -#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */ -#define CONFIG_NR_DRAM_BANKS 4 -#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ -#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* specify more that one ports available */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ #endif /* CONFIG_CMD_NET */ -/* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI /* Enable EHCI USB support */ -#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */ -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION -#define CONFIG_SUPPORT_VFAT -#endif /* CONFIG_CMD_USB */ - /* * File system */ From d30b5706d8502df4c00dfa9ebd054a19fed6d496 Mon Sep 17 00:00:00 2001 From: Prafulla Wadaskar Date: Thu, 30 Sep 2010 22:57:02 +0530 Subject: [PATCH 6/6] Kirkwood: Changes specific to ARM relocation support All Kirkwood based boards are supported for this new implementation ref: docs/README.arm-relocation Signed-off-by: Prafulla Wadaskar --- include/configs/mv-common.h | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h index e78d29f832..bdcebd3b5d 100644 --- a/include/configs/mv-common.h +++ b/include/configs/mv-common.h @@ -55,6 +55,11 @@ #error "Unsupported SoC" #endif +/* additions for new ARM relocation support */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +/* Kirkwood has 2k of Security SRAM, use it for SP */ +#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000 + /* * CLKs configurations */