diff --git a/README b/README index ba9be2be57..a5c3e8dcf7 100644 --- a/README +++ b/README @@ -1928,11 +1928,114 @@ CBFS (Coreboot Filesystem) support on those systems that support this (optional) feature, like the TQM8xxL modules. -- I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C +- I2C Support: CONFIG_SYS_I2C - These enable I2C serial bus commands. Defining either of - (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will - include the appropriate I2C driver for the selected CPU. + This enable the NEW i2c subsystem, and will allow you to use + i2c commands at the u-boot command line (as long as you set + CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c + based realtime clock chips or other i2c devices. See + common/cmd_i2c.c for a description of the command line + interface. + + ported i2c driver to the new framework: + - drivers/i2c/soft_i2c.c: + - activate first bus with CONFIG_SYS_I2C_SOFT define + CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE + for defining speed and slave address + - activate second bus with I2C_SOFT_DECLARATIONS2 define + CONFIG_SYS_I2C_SOFT_SPEED_2 and CONFIG_SYS_I2C_SOFT_SLAVE_2 + for defining speed and slave address + - activate third bus with I2C_SOFT_DECLARATIONS3 define + CONFIG_SYS_I2C_SOFT_SPEED_3 and CONFIG_SYS_I2C_SOFT_SLAVE_3 + for defining speed and slave address + - activate fourth bus with I2C_SOFT_DECLARATIONS4 define + CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4 + for defining speed and slave address + + - drivers/i2c/fsl_i2c.c: + - activate i2c driver with CONFIG_SYS_I2C_FSL + define CONFIG_SYS_FSL_I2C_OFFSET for setting the register + offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and + CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first + bus. + - If your board supports a second fsl i2c bus, define + CONFIG_SYS_FSL_I2C2_OFFSET for the register offset + CONFIG_SYS_FSL_I2C2_SPEED for the speed and + CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the + second bus. + + - drivers/i2c/tegra_i2c.c: + - activate this driver with CONFIG_SYS_I2C_TEGRA + - This driver adds 4 i2c buses with a fix speed from + 100000 and the slave addr 0! + + - drivers/i2c/ppc4xx_i2c.c + - activate this driver with CONFIG_SYS_I2C_PPC4XX + - CONFIG_SYS_I2C_PPC4XX_CH0 activate hardware channel 0 + - CONFIG_SYS_I2C_PPC4XX_CH1 activate hardware channel 1 + + additional defines: + + CONFIG_SYS_NUM_I2C_BUSES + Hold the number of i2c busses you want to use. If you + don't use/have i2c muxes on your i2c bus, this + is equal to CONFIG_SYS_NUM_I2C_ADAPTERS, and you can + omit this define. + + CONFIG_SYS_I2C_DIRECT_BUS + define this, if you don't use i2c muxes on your hardware. + if CONFIG_SYS_I2C_MAX_HOPS is not defined or == 0 you can + omit this define. + + CONFIG_SYS_I2C_MAX_HOPS + define how many muxes are maximal consecutively connected + on one i2c bus. If you not use i2c muxes, omit this + define. + + CONFIG_SYS_I2C_BUSES + hold a list of busses you want to use, only used if + CONFIG_SYS_I2C_DIRECT_BUS is not defined, for example + a board with CONFIG_SYS_I2C_MAX_HOPS = 1 and + CONFIG_SYS_NUM_I2C_BUSES = 9: + + CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP}}, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1}}}, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2}}}, \ + {0, {{I2C_MUX_PCA9547, 0x70, 3}}}, \ + {0, {{I2C_MUX_PCA9547, 0x70, 4}}}, \ + {0, {{I2C_MUX_PCA9547, 0x70, 5}}}, \ + {1, {I2C_NULL_HOP}}, \ + {1, {{I2C_MUX_PCA9544, 0x72, 1}}}, \ + {1, {{I2C_MUX_PCA9544, 0x72, 2}}}, \ + } + + which defines + bus 0 on adapter 0 without a mux + bus 1 on adapter 0 with a PCA9547 on address 0x70 port 1 + bus 2 on adapter 0 with a PCA9547 on address 0x70 port 2 + bus 3 on adapter 0 with a PCA9547 on address 0x70 port 3 + bus 4 on adapter 0 with a PCA9547 on address 0x70 port 4 + bus 5 on adapter 0 with a PCA9547 on address 0x70 port 5 + bus 6 on adapter 1 without a mux + bus 7 on adapter 1 with a PCA9544 on address 0x72 port 1 + bus 8 on adapter 1 with a PCA9544 on address 0x72 port 2 + + If you do not have i2c muxes on your board, omit this define. + +- Legacy I2C Support: CONFIG_HARD_I2C + + NOTE: It is intended to move drivers to CONFIG_SYS_I2C which + provides the following compelling advantages: + + - more than one i2c adapter is usable + - approved multibus support + - better i2c mux support + + ** Please consider updating your I2C driver now. ** + + These enable legacy I2C serial bus commands. Defining + CONFIG_HARD_I2C will include the appropriate I2C driver + for the selected CPU. This will allow you to use i2c commands at the u-boot command line (as long as you set CONFIG_CMD_I2C in @@ -1942,12 +2045,8 @@ CBFS (Coreboot Filesystem) support CONFIG_HARD_I2C selects a hardware I2C controller. - CONFIG_SOFT_I2C configures u-boot to use a software (aka - bit-banging) driver instead of CPM or similar hardware - support for I2C. - There are several other quantities that must also be - defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C. + defined when you define CONFIG_HARD_I2C. In both cases you will need to define CONFIG_SYS_I2C_SPEED to be the frequency (in Hz) at which you wish your i2c bus @@ -1969,7 +2068,7 @@ CBFS (Coreboot Filesystem) support That's all that's required for CONFIG_HARD_I2C. - If you use the software i2c interface (CONFIG_SOFT_I2C) + If you use the software i2c interface (CONFIG_SYS_I2C_SOFT) then the following macros need to be defined (examples are from include/configs/lwmon.h): @@ -2120,58 +2219,6 @@ CBFS (Coreboot Filesystem) support If not defined, then U-Boot uses predefined value for specified DTT device. - CONFIG_FSL_I2C - - Define this option if you want to use Freescale's I2C driver in - drivers/i2c/fsl_i2c.c. - - CONFIG_I2C_MUX - - Define this option if you have I2C devices reached over 1 .. n - I2C Muxes like the pca9544a. This option addes a new I2C - Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a - new I2C Bus to the existing I2C Busses. If you select the - new Bus with "i2c dev", u-bbot sends first the commandos for - the muxes to activate this new "bus". - - CONFIG_I2C_MULTI_BUS must be also defined, to use this - feature! - - Example: - Adding a new I2C Bus reached over 2 pca9544a muxes - The First mux with address 70 and channel 6 - The Second mux with address 71 and channel 4 - - => i2c bus pca9544a:70:6:pca9544a:71:4 - - Use the "i2c bus" command without parameter, to get a list - of I2C Busses with muxes: - - => i2c bus - Busses reached over muxes: - Bus ID: 2 - reached over Mux(es): - pca9544a@70 ch: 4 - Bus ID: 3 - reached over Mux(es): - pca9544a@70 ch: 6 - pca9544a@71 ch: 4 - => - - If you now switch to the new I2C Bus 3 with "i2c dev 3" - u-boot first sends the command to the mux@70 to enable - channel 6, and then the command to the mux@71 to enable - the channel 4. - - After that, you can use the "normal" i2c commands as - usual to communicate with your I2C devices behind - the 2 muxes. - - This option is actually implemented for the bitbanging - algorithm in common/soft_i2c.c and for the Hardware I2C - Bus on the MPC8260. But it should be not so difficult - to add this option to other architectures. - CONFIG_SOFT_I2C_READ_REPEATED_START defining this will force the i2c_read() function in @@ -3588,7 +3635,7 @@ to save the current settings. I2C muxes, you can define here, how to reach this EEPROM. For example: - #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0" + #define CONFIG_I2C_ENV_EEPROM_BUS 1 EEPROM which holds the environment, is reached over a pca9547 i2c mux with address 0x70, channel 3. diff --git a/arch/arm/cpu/armv7/vf610/generic.c b/arch/arm/cpu/armv7/vf610/generic.c index 48dd60aa69..a26d63ebe0 100644 --- a/arch/arm/cpu/armv7/vf610/generic.c +++ b/arch/arm/cpu/armv7/vf610/generic.c @@ -191,6 +191,11 @@ u32 get_fec_clk(void) return freq; } +static u32 get_i2c_clk(void) +{ + return get_ipg_clk(); +} + unsigned int mxc_get_clock(enum mxc_clock clk) { switch (clk) { @@ -206,6 +211,8 @@ unsigned int mxc_get_clock(enum mxc_clock clk) return get_sdhc_clk(); case MXC_FEC_CLK: return get_fec_clk(); + case MXC_I2C_CLK: + return get_i2c_clk(); default: break; } diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h index 78d144184a..197703b838 100644 --- a/arch/arm/include/asm/arch-kirkwood/config.h +++ b/arch/arm/include/asm/arch-kirkwood/config.h @@ -128,7 +128,7 @@ * I2C related stuff */ #ifdef CONFIG_CMD_I2C -#ifndef CONFIG_SOFT_I2C +#ifndef CONFIG_SYS_I2C_SOFT #define CONFIG_I2C_MVTWSI #endif #define CONFIG_SYS_I2C_SLAVE 0x0 diff --git a/arch/arm/include/asm/arch-vf610/clock.h b/arch/arm/include/asm/arch-vf610/clock.h index 9b2e2b06dd..535adadd79 100644 --- a/arch/arm/include/asm/arch-vf610/clock.h +++ b/arch/arm/include/asm/arch-vf610/clock.h @@ -16,6 +16,7 @@ enum mxc_clock { MXC_UART_CLK, MXC_ESDHC_CLK, MXC_FEC_CLK, + MXC_I2C_CLK, }; void enable_ocotp_clk(unsigned char enable); diff --git a/arch/arm/include/asm/arch-vf610/crm_regs.h b/arch/arm/include/asm/arch-vf610/crm_regs.h index 8532ead237..85f1fda9f5 100644 --- a/arch/arm/include/asm/arch-vf610/crm_regs.h +++ b/arch/arm/include/asm/arch-vf610/crm_regs.h @@ -177,6 +177,7 @@ struct anadig_reg { #define CCM_CCGR4_WKUP_CTRL_MASK (0x3 << 20) #define CCM_CCGR4_CCM_CTRL_MASK (0x3 << 22) #define CCM_CCGR4_GPC_CTRL_MASK (0x3 << 24) +#define CCM_CCGR4_I2C0_CTRL_MASK (0x3 << 12) #define CCM_CCGR6_OCOTP_CTRL_MASK (0x3 << 10) #define CCM_CCGR6_DDRMC_CTRL_MASK (0x3 << 28) #define CCM_CCGR7_SDHC1_CTRL_MASK (0x3 << 4) diff --git a/arch/arm/include/asm/arch-vf610/imx-regs.h b/arch/arm/include/asm/arch-vf610/imx-regs.h index 9e42be9756..b8c877f939 100644 --- a/arch/arm/include/asm/arch-vf610/imx-regs.h +++ b/arch/arm/include/asm/arch-vf610/imx-regs.h @@ -90,6 +90,7 @@ #define CONFIG_IOMUX_SHARE_CONF_REG #define FEC_QUIRK_ENET_MAC +#define I2C_QUIRK_REG /* MSCM interrupt rounter */ #define MSCM_IRSPRC_CP0_EN 1 diff --git a/arch/arm/include/asm/arch-vf610/iomux-vf610.h b/arch/arm/include/asm/arch-vf610/iomux-vf610.h index 385a23effe..4a39eb0d60 100644 --- a/arch/arm/include/asm/arch-vf610/iomux-vf610.h +++ b/arch/arm/include/asm/arch-vf610/iomux-vf610.h @@ -17,6 +17,8 @@ #define VF610_ENET_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_50ohm | \ PAD_CTL_OBE_IBE_ENABLE) #define VF610_DDR_PAD_CTRL PAD_CTL_DSE_25ohm +#define VF610_I2C_PAD_CTRL (PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_50ohm | \ + PAD_CTL_SPEED_HIGH | PAD_CTL_OBE_IBE_ENABLE) enum { VF610_PAD_PTA6__RMII0_CLKIN = IOMUX_PAD(0x0000, 0x0000, 2, __NA_, 0, VF610_ENET_PAD_CTRL), @@ -37,6 +39,8 @@ enum { VF610_PAD_PTA27__ESDHC1_DAT1 = IOMUX_PAD(0x0044, 0x0044, 5, __NA_, 0, VF610_SDHC_PAD_CTRL), VF610_PAD_PTA28__ESDHC1_DAT2 = IOMUX_PAD(0x0048, 0x0048, 5, __NA_, 0, VF610_SDHC_PAD_CTRL), VF610_PAD_PTA29__ESDHC1_DAT3 = IOMUX_PAD(0x004c, 0x004c, 5, __NA_, 0, VF610_SDHC_PAD_CTRL), + VF610_PAD_PTB14__I2C0_SCL = IOMUX_PAD(0x0090, 0x0090, 2, 0x033c, 1, VF610_I2C_PAD_CTRL), + VF610_PAD_PTB15__I2C0_SDA = IOMUX_PAD(0x0094, 0x0094, 2, 0x0340, 1, VF610_I2C_PAD_CTRL), VF610_PAD_DDR_A15__DDR_A_15 = IOMUX_PAD(0x0220, 0x0220, 0, __NA_, 0, VF610_DDR_PAD_CTRL), VF610_PAD_DDR_A14__DDR_A_14 = IOMUX_PAD(0x0224, 0x0224, 0, __NA_, 0, VF610_DDR_PAD_CTRL), VF610_PAD_DDR_A13__DDR_A_13 = IOMUX_PAD(0x0228, 0x0228, 0, __NA_, 0, VF610_DDR_PAD_CTRL), diff --git a/arch/arm/lib/board.c b/arch/arm/lib/board.c index 7c1b021488..9c72a5353f 100644 --- a/arch/arm/lib/board.c +++ b/arch/arm/lib/board.c @@ -53,7 +53,7 @@ extern void dataflash_print_info(void); #endif #if defined(CONFIG_HARD_I2C) || \ - defined(CONFIG_SOFT_I2C) + defined(CONFIG_SYS_I2C) #include #endif @@ -149,11 +149,15 @@ static int display_dram_config(void) return (0); } -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) static int init_func_i2c(void) { puts("I2C: "); +#ifdef CONFIG_SYS_I2C + i2c_init_all(); +#else i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#endif puts("ready\n"); return (0); } @@ -252,7 +256,7 @@ init_fnc_t *init_sequence[] = { #if defined(CONFIG_DISPLAY_BOARDINFO) checkboard, /* display board info */ #endif -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) init_func_i2c, #endif dram_init, /* configure available RAM banks */ diff --git a/arch/blackfin/lib/board.c b/arch/blackfin/lib/board.c index f1d55470e8..10223bdb79 100644 --- a/arch/blackfin/lib/board.c +++ b/arch/blackfin/lib/board.c @@ -37,6 +37,10 @@ int post_flag; #endif +#if defined(CONFIG_SYS_I2C) +#include +#endif + DECLARE_GLOBAL_DATA_PTR; __attribute__((always_inline)) @@ -387,6 +391,9 @@ void board_init_r(gd_t * id, ulong dest_addr) mmc_initialize(bd); #endif +#if defined(CONFIG_SYS_I2C) + i2c_reloc_fixup(); +#endif /* relocate environment function pointers etc. */ env_relocate(); diff --git a/arch/m68k/cpu/mcf5227x/cpu_init.c b/arch/m68k/cpu/mcf5227x/cpu_init.c index 7e8f832fed..91b5fadc88 100644 --- a/arch/m68k/cpu/mcf5227x/cpu_init.c +++ b/arch/m68k/cpu/mcf5227x/cpu_init.c @@ -89,7 +89,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL out_8(&gpio->par_i2c, GPIO_PAR_I2C_SCL_SCL | GPIO_PAR_I2C_SDA_SDA); #endif diff --git a/arch/m68k/cpu/mcf5227x/speed.c b/arch/m68k/cpu/mcf5227x/speed.c index 08e49906f5..44de4a6701 100644 --- a/arch/m68k/cpu/mcf5227x/speed.c +++ b/arch/m68k/cpu/mcf5227x/speed.c @@ -118,7 +118,7 @@ int get_clocks(void) gd->bus_clk = gd->arch.flb_clk; } -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/cpu/mcf523x/cpu_init.c b/arch/m68k/cpu/mcf523x/cpu_init.c index 494c5495a5..5a789540fc 100644 --- a/arch/m68k/cpu/mcf523x/cpu_init.c +++ b/arch/m68k/cpu/mcf523x/cpu_init.c @@ -99,7 +99,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr7, CONFIG_SYS_CS7_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL CONFIG_SYS_I2C_PINMUX_REG &= CONFIG_SYS_I2C_PINMUX_CLR; CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET; #endif diff --git a/arch/m68k/cpu/mcf523x/speed.c b/arch/m68k/cpu/mcf523x/speed.c index 5abd77149f..a4aa05b3fa 100644 --- a/arch/m68k/cpu/mcf523x/speed.c +++ b/arch/m68k/cpu/mcf523x/speed.c @@ -31,7 +31,7 @@ int get_clocks(void) gd->bus_clk = CONFIG_SYS_CLK; gd->cpu_clk = (gd->bus_clk * 2); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/cpu/mcf52x2/cpu_init.c b/arch/m68k/cpu/mcf52x2/cpu_init.c index dc703695d8..0882c3b8e5 100644 --- a/arch/m68k/cpu/mcf52x2/cpu_init.c +++ b/arch/m68k/cpu/mcf52x2/cpu_init.c @@ -212,7 +212,7 @@ void cpu_init_f(void) /* FlexBus Chipselect */ init_fbcs(); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL CONFIG_SYS_I2C_PINMUX_REG = CONFIG_SYS_I2C_PINMUX_REG & CONFIG_SYS_I2C_PINMUX_CLR; CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET; @@ -482,7 +482,7 @@ void cpu_init_f(void) init_fbcs(); #endif /* #ifndef CONFIG_MONITOR_IS_IN_RAM */ -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL CONFIG_SYS_I2C_PINMUX_REG &= CONFIG_SYS_I2C_PINMUX_CLR; CONFIG_SYS_I2C_PINMUX_REG |= CONFIG_SYS_I2C_PINMUX_SET; #endif diff --git a/arch/m68k/cpu/mcf52x2/speed.c b/arch/m68k/cpu/mcf52x2/speed.c index d0f9762d0b..c5961d45ec 100644 --- a/arch/m68k/cpu/mcf52x2/speed.c +++ b/arch/m68k/cpu/mcf52x2/speed.c @@ -74,9 +74,9 @@ int get_clocks (void) gd->bus_clk = gd->cpu_clk; #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; -#ifdef CONFIG_SYS_I2C2_OFFSET +#ifdef CONFIG_SYS_I2C2_FSL_OFFSET gd->arch.i2c2_clk = gd->bus_clk; #endif #endif diff --git a/arch/m68k/cpu/mcf532x/cpu_init.c b/arch/m68k/cpu/mcf532x/cpu_init.c index f7101fd6d2..db7ded4782 100644 --- a/arch/m68k/cpu/mcf532x/cpu_init.c +++ b/arch/m68k/cpu/mcf532x/cpu_init.c @@ -82,7 +82,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL out_8(&gpio->par_feci2c, GPIO_PAR_FECI2C_SDA_SDA | GPIO_PAR_FECI2C_SCL_SCL); #endif @@ -276,7 +276,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL out_8(&gpio->par_feci2c, GPIO_PAR_FECI2C_SCL_SCL | GPIO_PAR_FECI2C_SDA_SDA); #endif diff --git a/arch/m68k/cpu/mcf532x/speed.c b/arch/m68k/cpu/mcf532x/speed.c index b412abe7d1..a440bbb3b6 100644 --- a/arch/m68k/cpu/mcf532x/speed.c +++ b/arch/m68k/cpu/mcf532x/speed.c @@ -254,7 +254,7 @@ int get_clocks(void) gd->bus_clk = clock_pll(CONFIG_SYS_CLK / 1000, 0) * 1000; gd->cpu_clk = (gd->bus_clk * 3); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/cpu/mcf5445x/cpu_init.c b/arch/m68k/cpu/mcf5445x/cpu_init.c index 955968c0db..9c324dc968 100644 --- a/arch/m68k/cpu/mcf5445x/cpu_init.c +++ b/arch/m68k/cpu/mcf5445x/cpu_init.c @@ -196,7 +196,7 @@ void cpu_init_f(void) GPIO_PAR_FBCTL_OE | GPIO_PAR_FBCTL_TA_TA | GPIO_PAR_FBCTL_RW_RW | GPIO_PAR_FBCTL_TS_TS); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_FSL_I2C out_be16(&gpio->par_feci2c, GPIO_PAR_FECI2C_SCL_SCL | GPIO_PAR_FECI2C_SDA_SDA); #endif diff --git a/arch/m68k/cpu/mcf5445x/speed.c b/arch/m68k/cpu/mcf5445x/speed.c index 594716b6ca..07a9b359b5 100644 --- a/arch/m68k/cpu/mcf5445x/speed.c +++ b/arch/m68k/cpu/mcf5445x/speed.c @@ -257,7 +257,7 @@ void setup_5445x_clocks(void) #endif } -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif } @@ -273,7 +273,7 @@ int get_clocks(void) setup_5445x_clocks(); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_FSL_I2C gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/cpu/mcf547x_8x/cpu_init.c b/arch/m68k/cpu/mcf547x_8x/cpu_init.c index a9e3b4392f..c3df831f14 100644 --- a/arch/m68k/cpu/mcf547x_8x/cpu_init.c +++ b/arch/m68k/cpu/mcf547x_8x/cpu_init.c @@ -79,7 +79,7 @@ void cpu_init_f(void) out_be32(&fbcs->csmr5, CONFIG_SYS_CS5_MASK); #endif -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL out_be16(&gpio->par_feci2cirq, GPIO_PAR_FECI2CIRQ_SCL | GPIO_PAR_FECI2CIRQ_SDA); #endif diff --git a/arch/m68k/cpu/mcf547x_8x/speed.c b/arch/m68k/cpu/mcf547x_8x/speed.c index f516b10a13..2bc4c44247 100644 --- a/arch/m68k/cpu/mcf547x_8x/speed.c +++ b/arch/m68k/cpu/mcf547x_8x/speed.c @@ -24,7 +24,7 @@ int get_clocks(void) gd->bus_clk = CONFIG_SYS_CLK; gd->cpu_clk = (gd->bus_clk * 2); -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL gd->arch.i2c1_clk = gd->bus_clk; #endif diff --git a/arch/m68k/include/asm/global_data.h b/arch/m68k/include/asm/global_data.h index 0903644cdd..b55c91e613 100644 --- a/arch/m68k/include/asm/global_data.h +++ b/arch/m68k/include/asm/global_data.h @@ -10,7 +10,7 @@ /* Architecture-specific global data */ struct arch_global_data { -#ifdef CONFIG_FSL_I2C +#ifdef CONFIG_SYS_I2C_FSL unsigned long i2c1_clk; unsigned long i2c2_clk; #endif diff --git a/arch/m68k/lib/board.c b/arch/m68k/lib/board.c index 020dc2456e..e75b6a98dd 100644 --- a/arch/m68k/lib/board.c +++ b/arch/m68k/lib/board.c @@ -40,7 +40,7 @@ #include #if defined(CONFIG_HARD_I2C) || \ - defined(CONFIG_SOFT_I2C) + defined(CONFIG_SYS_I2C) #include #endif @@ -126,11 +126,15 @@ static int init_func_ram (void) /***********************************************************************/ -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) static int init_func_i2c (void) { puts ("I2C: "); +#ifdef CONFIG_SYS_I2C + i2c_init_all(); +#else i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#endif puts ("ready\n"); return (0); } @@ -162,7 +166,7 @@ init_fnc_t *init_sequence[] = { display_options, checkcpu, checkboard, -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) init_func_i2c, #endif #if defined(CONFIG_HARD_SPI) @@ -485,6 +489,11 @@ void board_init_r (gd_t *id, ulong dest_addr) spi_init_r (); #endif +#if defined(CONFIG_SYS_I2C) + /* Adjust I2C subsystem pointers after relocation */ + i2c_reloc_fixup(); +#endif + /* relocate environment function pointers etc. */ env_relocate (); diff --git a/arch/nds32/lib/board.c b/arch/nds32/lib/board.c index 7a25522b4a..2d4c6231a3 100644 --- a/arch/nds32/lib/board.c +++ b/arch/nds32/lib/board.c @@ -24,6 +24,10 @@ DECLARE_GLOBAL_DATA_PTR; +#if defined(CONFIG_SYS_I2C) +#include +#endif + ulong monitor_flash_len; /* @@ -157,7 +161,7 @@ init_fnc_t *init_sequence[] = { #if defined(CONFIG_DISPLAY_BOARDINFO) checkboard, /* display board info */ #endif -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) init_func_i2c, #endif dram_init, /* configure available RAM banks */ @@ -331,6 +335,10 @@ void board_init_r(gd_t *id, ulong dest_addr) mmc_initialize(gd->bd); #endif +#if defined(CONFIG_SYS_I2C_ADAPTERS) + i2c_reloc_fixup(); +#endif + /* initialize environment */ env_relocate(); diff --git a/arch/powerpc/cpu/mpc8260/i2c.c b/arch/powerpc/cpu/mpc8260/i2c.c index fc8d2ef82c..8658ebdadd 100644 --- a/arch/powerpc/cpu/mpc8260/i2c.c +++ b/arch/powerpc/cpu/mpc8260/i2c.c @@ -730,23 +730,9 @@ unsigned int i2c_get_bus_num(void) int i2c_set_bus_num(unsigned int bus) { -#if defined(CONFIG_I2C_MUX) - if (bus < CONFIG_SYS_MAX_I2C_BUS) { - i2c_bus_num = bus; - } else { - int ret; - - ret = i2x_mux_select_mux(bus); - if (ret == 0) - i2c_bus_num = bus; - else - return ret; - } -#else if (bus >= CONFIG_SYS_MAX_I2C_BUS) return -1; i2c_bus_num = bus; -#endif return 0; } diff --git a/arch/powerpc/cpu/mpc8xx/video.c b/arch/powerpc/cpu/mpc8xx/video.c index 8d790b4e88..02cd0debc2 100644 --- a/arch/powerpc/cpu/mpc8xx/video.c +++ b/arch/powerpc/cpu/mpc8xx/video.c @@ -793,7 +793,11 @@ static void video_encoder_init (void) /* Initialize the I2C */ debug ("[VIDEO ENCODER] Initializing I2C bus...\n"); +#ifdef CONFIG_SYS_I2C + i2c_init_all(); +#else i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#endif #ifdef CONFIG_FADS /* Reset ADV7176 chip */ diff --git a/arch/powerpc/cpu/ppc4xx/40x_spd_sdram.c b/arch/powerpc/cpu/ppc4xx/40x_spd_sdram.c index 55a58f6b18..4417646f83 100644 --- a/arch/powerpc/cpu/ppc4xx/40x_spd_sdram.c +++ b/arch/powerpc/cpu/ppc4xx/40x_spd_sdram.c @@ -36,10 +36,6 @@ /* * Set default values */ -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 50000 -#endif - #define ONE_BILLION 1000000000 #define SDRAM0_CFG_DCE 0x80000000 @@ -142,7 +138,7 @@ long int spd_sdram(int(read_spd)(uint addr)) * Make sure I2C controller is initialized * before continuing. */ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); } /* Make shure we are using SDRAM */ diff --git a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr.c b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr.c index 9d23e7653f..52340f209d 100644 --- a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr.c +++ b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr.c @@ -46,10 +46,6 @@ /* * Set default values */ -#ifndef CONFIG_SYS_I2C_SPEED -#define CONFIG_SYS_I2C_SPEED 50000 -#endif - #define ONE_BILLION 1000000000 /* @@ -152,7 +148,7 @@ long int spd_sdram(void) { * Make sure I2C controller is initialized * before continuing. */ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); /* * Read the SPD information using I2C interface. Check to see if the diff --git a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c index d30f442eb3..fe928db039 100644 --- a/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c +++ b/arch/powerpc/cpu/ppc4xx/44x_spd_ddr2.c @@ -442,8 +442,7 @@ phys_size_t initdram(int board_type) */ /* switch to correct I2C bus */ - I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); /*------------------------------------------------------------------ * Clear out the serial presence detect buffers. diff --git a/arch/powerpc/cpu/ppc4xx/cmd_chip_config.c b/arch/powerpc/cpu/ppc4xx/cmd_chip_config.c index b777d73295..4e9a40d585 100644 --- a/arch/powerpc/cpu/ppc4xx/cmd_chip_config.c +++ b/arch/powerpc/cpu/ppc4xx/cmd_chip_config.c @@ -39,7 +39,7 @@ static int do_chip_config(cmd_tbl_t *cmdtp, int flag, int argc, char * const arg * First switch to correct I2C bus. This is I2C bus 0 * for all currently available 4xx derivats. */ - I2C_SET_BUS(0); + i2c_set_bus_num(0); #ifdef CONFIG_CMD_EEPROM ret = eeprom_read(CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR, diff --git a/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c b/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c index 55278b19bf..916451a2b0 100644 --- a/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c +++ b/arch/powerpc/cpu/ppc4xx/denali_spd_ddr2.c @@ -1024,8 +1024,7 @@ phys_size_t initdram(int board_type) * before continuing. */ /* switch to correct I2C bus */ - I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); /*------------------------------------------------------------------ * Clear out the serial presence detect buffers. diff --git a/arch/powerpc/include/asm/ppc4xx-i2c.h b/arch/powerpc/include/asm/ppc4xx-i2c.h index bbf7f35589..09189cf19b 100644 --- a/arch/powerpc/include/asm/ppc4xx-i2c.h +++ b/arch/powerpc/include/asm/ppc4xx-i2c.h @@ -18,24 +18,6 @@ #define IIC_TIMEOUT 1 /* 1 second */ -#if defined(CONFIG_I2C_MULTI_BUS) -#define I2C_BUS_OFFS (i2c_bus_num * 0x100) -#else -#define I2C_BUS_OFFS (0x000) -#endif /* CONFIG_I2C_MULTI_BUS */ - -#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) -#define I2C_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700 + I2C_BUS_OFFS) -#elif defined(CONFIG_440) || defined(CONFIG_405EX) -/* all remaining 440 variants */ -#define I2C_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x00000400 + I2C_BUS_OFFS) -#else -/* all 405 variants */ -#define I2C_BASE_ADDR (0xEF600500 + I2C_BUS_OFFS) -#endif - struct ppc4xx_i2c { u8 mdbuf; u8 res1; diff --git a/arch/powerpc/lib/board.c b/arch/powerpc/lib/board.c index bef3f76f0c..a101e03601 100644 --- a/arch/powerpc/lib/board.c +++ b/arch/powerpc/lib/board.c @@ -82,8 +82,7 @@ extern void sc3_read_eeprom(void); #if defined(CONFIG_CMD_DOC) void doc_init(void); #endif -#if defined(CONFIG_HARD_I2C) || \ - defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) #include #endif #include @@ -198,11 +197,15 @@ static int init_func_ram(void) /***********************************************************************/ -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) static int init_func_i2c(void) { puts("I2C: "); +#ifdef CONFIG_SYS_I2C + i2c_init_all(); +#else i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#endif puts("ready\n"); return 0; } @@ -291,7 +294,7 @@ static init_fnc_t *init_sequence[] = { misc_init_f, #endif INIT_FUNC_WATCHDOG_RESET -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) init_func_i2c, #endif #if defined(CONFIG_HARD_SPI) diff --git a/board/BuS/eb_cpux9k2/cpux9k2.c b/board/BuS/eb_cpux9k2/cpux9k2.c index 9fd8e7acd1..5e4778e978 100644 --- a/board/BuS/eb_cpux9k2/cpux9k2.c +++ b/board/BuS/eb_cpux9k2/cpux9k2.c @@ -272,7 +272,7 @@ int drv_video_init(void) } #endif -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT void i2c_init_board(void) { diff --git a/board/BuS/vl_ma2sc/vl_ma2sc.c b/board/BuS/vl_ma2sc/vl_ma2sc.c index 2dba146f10..e2ae6fde6c 100644 --- a/board/BuS/vl_ma2sc/vl_ma2sc.c +++ b/board/BuS/vl_ma2sc/vl_ma2sc.c @@ -307,7 +307,7 @@ int board_eth_init(bd_t *bis) return rc; } -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT void i2c_init_board(void) { u32 pin; diff --git a/board/atc/atc.c b/board/atc/atc.c index ee395d92bd..0038561b10 100644 --- a/board/atc/atc.c +++ b/board/atc/atc.c @@ -154,7 +154,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */ /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */ /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ #else diff --git a/board/bluewater/snapper9260/snapper9260.c b/board/bluewater/snapper9260/snapper9260.c index be03553384..8a6919dbb1 100644 --- a/board/bluewater/snapper9260/snapper9260.c +++ b/board/bluewater/snapper9260/snapper9260.c @@ -132,7 +132,7 @@ int board_init(void) /* Initialise peripherals */ at91_seriald_hw_init(); - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); nand_hw_init(); macb_hw_init(); diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c index 58f5a36f81..e391dfc9e1 100644 --- a/board/cm5200/cm5200.c +++ b/board/cm5200/cm5200.c @@ -309,7 +309,7 @@ int board_early_init_r(void) #ifdef CONFIG_MISC_INIT_R int misc_init_r(void) { -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) uchar buf[6]; char str[18]; char hostname[MODULE_NAME_MAXLEN]; @@ -332,7 +332,7 @@ int misc_init_r(void) " device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM, CONFIG_MAC_OFFSET); } -#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) */ +#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */ if (!getenv("ethaddr")) printf(LOG_PREFIX "MAC address not set, networking is not " "operational\n"); diff --git a/board/cpu86/cpu86.c b/board/cpu86/cpu86.c index a1f25ba71e..929291052f 100644 --- a/board/cpu86/cpu86.c +++ b/board/cpu86/cpu86.c @@ -145,7 +145,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */ /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */ /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ #else diff --git a/board/cpu87/cpu87.c b/board/cpu87/cpu87.c index b6293073f6..01f90d2ebb 100644 --- a/board/cpu87/cpu87.c +++ b/board/cpu87/cpu87.c @@ -147,7 +147,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */ /* PD17 */ { 0, 0, 0, 0, 0, 0 }, /* PD17 */ /* PD16 */ { 0, 0, 0, 0, 0, 0 }, /* PD16 */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ #else diff --git a/board/csb272/csb272.c b/board/csb272/csb272.c index bfc47e0b4e..43a1aa0521 100644 --- a/board/csb272/csb272.c +++ b/board/csb272/csb272.c @@ -35,7 +35,7 @@ uchar pll_fs6377_regs[16] = { */ int pll_init(void) { - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); return i2c_write(CONFIG_SYS_I2C_PLL_ADDR, 0, 1, (uchar *) pll_fs6377_regs, sizeof(pll_fs6377_regs)); diff --git a/board/emk/top9000/top9000.c b/board/emk/top9000/top9000.c index 083e5e8df6..6e2ffddb0a 100644 --- a/board/emk/top9000/top9000.c +++ b/board/emk/top9000/top9000.c @@ -229,7 +229,7 @@ int board_eth_init(bd_t *bis) * However i2c_get_bus_num() cannot be called before * relocation. */ -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT void iic_init(void) { /* ports are now initialized in board_early_init_f() */ @@ -237,7 +237,7 @@ void iic_init(void) int iic_read(void) { - switch ((gd->flags & GD_FLG_RELOC) ? i2c_get_bus_num() : 0) { + switch (I2C_ADAP_HWNR) { case 0: return at91_get_pio_value(I2C0_PORT, SDA0_PIN); case 1: @@ -248,7 +248,7 @@ int iic_read(void) void iic_sda(int bit) { - switch ((gd->flags & GD_FLG_RELOC) ? i2c_get_bus_num() : 0) { + switch (I2C_ADAP_HWNR) { case 0: at91_set_pio_value(I2C0_PORT, SDA0_PIN, bit); break; @@ -260,7 +260,7 @@ void iic_sda(int bit) void iic_scl(int bit) { - switch ((gd->flags & GD_FLG_RELOC) ? i2c_get_bus_num() : 0) { + switch (I2C_ADAP_HWNR) { case 0: at91_set_pio_value(I2C0_PORT, SCL0_PIN, bit); break; diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c index dc35be4e2e..b168b247bd 100644 --- a/board/esd/du440/du440.c +++ b/board/esd/du440/du440.c @@ -372,7 +372,6 @@ int last_stage_init(void) return 0; } -#if defined(CONFIG_I2C_MULTI_BUS) /* * read field strength from I2C ADC */ @@ -487,7 +486,6 @@ U_BOOT_CMD( "Initialize USB hub", "" ); -#endif /* CONFIG_I2C_MULTI_BUS */ #define CONFIG_SYS_BOOT_EEPROM_PAGE_WRITE_BITS 3 int boot_eeprom_write (unsigned dev_addr, diff --git a/board/esd/vme8349/vme8349.c b/board/esd/vme8349/vme8349.c index e9a25786cd..01365dcbd3 100644 --- a/board/esd/vme8349/vme8349.c +++ b/board/esd/vme8349/vme8349.c @@ -169,11 +169,11 @@ static spd_eeprom_t default_spd_eeprom = { int vme8349_read_spd(uchar chip, uint addr, int alen, uchar *buffer, int len) { - int old_bus = I2C_GET_BUS(); + int old_bus = i2c_get_bus_num(); unsigned int l, sum; int valid = 0; - I2C_SET_BUS(0); + i2c_set_bus_num(0); if (i2c_read(chip, addr, alen, buffer, len) == 0) if (memcmp(&buffer[64], &default_spd_eeprom.mid[0], 8) == 0) { @@ -198,7 +198,7 @@ int vme8349_read_spd(uchar chip, uint addr, int alen, uchar *buffer, int len) buffer[63] = sum; } - I2C_SET_BUS(old_bus); + i2c_set_bus_num(old_bus); return 0; } diff --git a/board/eukrea/cpuat91/cpuat91.c b/board/eukrea/cpuat91/cpuat91.c index f649dd0406..ec0ce0b205 100644 --- a/board/eukrea/cpuat91/cpuat91.c +++ b/board/eukrea/cpuat91/cpuat91.c @@ -57,7 +57,7 @@ int board_eth_init(bd_t *bis) } #endif -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT void i2c_init_board(void) { u32 pin; diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README index b6e955bcad..3178d49d0a 100644 --- a/board/freescale/m52277evb/README +++ b/board/freescale/m52277evb/README @@ -82,9 +82,9 @@ CONFIG_CMD_DATE -- enable to use date feature in u-boot CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support -CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README index 64a3d42f0c..84fc1ecfb1 100644 --- a/board/freescale/m53017evb/README +++ b/board/freescale/m53017evb/README @@ -90,9 +90,9 @@ MCFFEC_TOUT_LOOP -- set FEC timeout loop CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support -CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README index 419d4d6d1e..52eac7b2ff 100644 --- a/board/freescale/m5373evb/README +++ b/board/freescale/m5373evb/README @@ -89,9 +89,9 @@ MCFFEC_TOUT_LOOP -- set FEC timeout loop CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support -CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README index 2bc6ce4bf3..c70c4c5c25 100644 --- a/board/freescale/m54455evb/README +++ b/board/freescale/m54455evb/README @@ -112,9 +112,9 @@ _IO_BASE -- define for IO base address CONFIG_MCFTMR -- define to use DMA timer CONFIG_MCFPIT -- define to use PIT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_FSL_I2C -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support -CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README index d3aec20e4f..ce497c0d2a 100644 --- a/board/freescale/m547xevb/README +++ b/board/freescale/m547xevb/README @@ -97,9 +97,9 @@ CONFIG_DOS_PARTITION -- enable DOS read/write CONFIG_SLTTMR -- define to use SLT timer -CONFIG_FSL_I2C -- define to use FSL common I2C driver +CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver CONFIG_HARD_I2C -- define for I2C hardware support -CONFIG_SOFT_I2C -- define for I2C bit-banged +CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged CONFIG_SYS_I2C_SPEED -- define for I2C speed CONFIG_SYS_I2C_SLAVE -- define for I2C slave address CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset diff --git a/board/freescale/mpc8349itx/mpc8349itx.c b/board/freescale/mpc8349itx/mpc8349itx.c index 510ef0453c..803d722806 100644 --- a/board/freescale/mpc8349itx/mpc8349itx.c +++ b/board/freescale/mpc8349itx/mpc8349itx.c @@ -247,8 +247,7 @@ int misc_init_r(void) { int rc = 0; -#ifdef CONFIG_HARD_I2C - +#if defined(CONFIG_SYS_I2C) unsigned int orig_bus = i2c_get_bus_num(); u8 i2c_data; diff --git a/board/freescale/mpc8349itx/pci.c b/board/freescale/mpc8349itx/pci.c index 64259776c7..afc9df0923 100644 --- a/board/freescale/mpc8349itx/pci.c +++ b/board/freescale/mpc8349itx/pci.c @@ -71,7 +71,7 @@ void pci_init_board(void) #endif u8 reg8; -#ifdef CONFIG_HARD_I2C +#if defined(CONFIG_SYS_I2C) i2c_set_bus_num(1); /* Read the PCI_M66EN jumper setting */ if ((i2c_read(CONFIG_SYS_I2C_8574_ADDR2, 0, 0, ®8, sizeof(reg8)) == 0) || diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c index d8b1e41e39..50553dacd9 100644 --- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c +++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c @@ -232,7 +232,7 @@ int checkboard(void) in_8(&cpld_data->pcba_rev) & 0x0F); /* Initialize i2c early for rom_loc and flash bank information */ - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); if (i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 0, 1, &in, 1) < 0 || i2c_read(CONFIG_SYS_I2C_PCA9557_ADDR, 1, 1, &out, 1) < 0 || diff --git a/board/freescale/vf610twr/vf610twr.c b/board/freescale/vf610twr/vf610twr.c index 7c6cb5be56..699ea7f010 100644 --- a/board/freescale/vf610twr/vf610twr.c +++ b/board/freescale/vf610twr/vf610twr.c @@ -14,6 +14,7 @@ #include #include #include +#include DECLARE_GLOBAL_DATA_PTR; @@ -267,6 +268,16 @@ static void setup_iomux_enet(void) imx_iomux_v3_setup_multiple_pads(enet0_pads, ARRAY_SIZE(enet0_pads)); } +static void setup_iomux_i2c(void) +{ + static const iomux_v3_cfg_t i2c0_pads[] = { + VF610_PAD_PTB14__I2C0_SCL, + VF610_PAD_PTB15__I2C0_SDA, + }; + + imx_iomux_v3_setup_multiple_pads(i2c0_pads, ARRAY_SIZE(i2c0_pads)); +} + #ifdef CONFIG_FSL_ESDHC struct fsl_esdhc_cfg esdhc_cfg[1] = { {ESDHC1_BASE_ADDR}, @@ -315,7 +326,7 @@ static void clock_init(void) CCM_CCGR3_ANADIG_CTRL_MASK); clrsetbits_le32(&ccm->ccgr4, CCM_REG_CTRL_MASK, CCM_CCGR4_WKUP_CTRL_MASK | CCM_CCGR4_CCM_CTRL_MASK | - CCM_CCGR4_GPC_CTRL_MASK); + CCM_CCGR4_GPC_CTRL_MASK | CCM_CCGR4_I2C0_CTRL_MASK); clrsetbits_le32(&ccm->ccgr6, CCM_REG_CTRL_MASK, CCM_CCGR6_OCOTP_CTRL_MASK | CCM_CCGR6_DDRMC_CTRL_MASK); clrsetbits_le32(&ccm->ccgr7, CCM_REG_CTRL_MASK, @@ -374,6 +385,7 @@ int board_early_init_f(void) setup_iomux_uart(); setup_iomux_enet(); + setup_iomux_i2c(); return 0; } diff --git a/board/ids8247/ids8247.c b/board/ids8247/ids8247.c index a51af03d5d..de6b8fbd9b 100644 --- a/board/ids8247/ids8247.c +++ b/board/ids8247/ids8247.c @@ -35,7 +35,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PA27 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 RXDV */ /* PA26 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 RXER */ /* PA25 */ { 0, 0, 0, 0, 1, 0 }, /* 8247_P0 */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PA24 */ { 1, 0, 0, 0, 1, 1 }, /* I2C_SDA2 */ /* PA23 */ { 1, 0, 0, 1, 1, 1 }, /* I2C_SCL2 */ #else /* normal I/O port pins */ diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c index 47c4450e3d..aabd3a85b7 100644 --- a/board/keymile/common/ivm.c +++ b/board/keymile/common/ivm.c @@ -298,29 +298,14 @@ int ivm_analyze_eeprom(unsigned char *buf, int len) int ivm_read_eeprom(void) { -#if defined(CONFIG_I2C_MUX) - I2C_MUX_DEVICE *dev = NULL; -#endif uchar i2c_buffer[CONFIG_SYS_IVM_EEPROM_MAX_LEN]; - uchar *buf; - unsigned long dev_addr = CONFIG_SYS_IVM_EEPROM_ADR; int ret; -#if defined(CONFIG_I2C_MUX) - /* First init the Bus, select the Bus */ - buf = (unsigned char *) getenv("EEprom_ivm"); - if (buf != NULL) - dev = i2c_mux_ident_muxstring(buf); - if (dev == NULL) { - printf("Error couldnt add Bus for IVM\n"); - return -1; - } - i2c_set_bus_num(dev->busid); -#endif + i2c_set_bus_num(CONFIG_KM_IVM_BUS); /* add deblocking here */ i2c_make_abort(); - ret = i2c_read(dev_addr, 0, 1, i2c_buffer, + ret = i2c_read(CONFIG_SYS_IVM_EEPROM_ADR, 0, 1, i2c_buffer, CONFIG_SYS_IVM_EEPROM_MAX_LEN); if (ret != 0) { printf("Error reading EEprom\n"); diff --git a/board/keymile/km83xx/km83xx.c b/board/keymile/km83xx/km83xx.c index b5ea7ae95b..cd861c9f12 100644 --- a/board/keymile/km83xx/km83xx.c +++ b/board/keymile/km83xx/km83xx.c @@ -92,19 +92,6 @@ const qe_iop_conf_t qe_iop_conf_tab[] = { {0, 0, 0, 0, QE_IOP_TAB_END}, }; -static int board_init_i2c_busses(void) -{ - I2C_MUX_DEVICE *dev = NULL; - uchar *dtt_bus = (uchar *)"pca9547:70:a"; - - /* Set up the Bus for the DTTs */ - dev = i2c_mux_ident_muxstring(dtt_bus); - if (dev == NULL) - printf("Error couldn't add Bus for DTT\n"); - - return 0; -} - #if defined(CONFIG_SUVD3) const uint upma_table[] = { 0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */ @@ -203,8 +190,6 @@ int board_early_init_r(void) int misc_init_r(void) { - /* add board specific i2c busses */ - board_init_i2c_busses(); return 0; } diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c index e76acc0dac..481876b2ed 100644 --- a/board/keymile/km_arm/km_arm.c +++ b/board/keymile/km_arm/km_arm.c @@ -47,7 +47,7 @@ static const u32 kwmpp_config[] = { MPP5_NF_IO7, MPP6_SYSRST_OUTn, MPP7_PEX_RST_OUTn, -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) MPP8_GPIO, /* SDA */ MPP9_GPIO, /* SCL */ #endif @@ -218,7 +218,7 @@ int misc_init_r(void) int board_early_init_f(void) { -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) u32 tmp; /* set the 2 bitbang i2c pins as output gpios */ @@ -244,7 +244,7 @@ int board_init(void) kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1); kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1); -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* * Reinit the GPIO for I2C Bitbang driver so that the now * available gpio framework is consistent. The calls to @@ -424,7 +424,7 @@ int hush_init_var(void) } #endif -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) void set_sda(int state) { I2C_ACTIVE; diff --git a/board/lwmon/lwmon.c b/board/lwmon/lwmon.c index fb7e54d523..225b1ef258 100644 --- a/board/lwmon/lwmon.c +++ b/board/lwmon/lwmon.c @@ -464,7 +464,7 @@ static void kbd_init (void) uchar val, errcd; int i; - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); gd->arch.kbd_status = 0; diff --git a/board/lwmon/pcmcia.c b/board/lwmon/pcmcia.c index acbb9d54d2..b9894cf011 100644 --- a/board/lwmon/pcmcia.c +++ b/board/lwmon/pcmcia.c @@ -104,7 +104,7 @@ int pcmcia_hardware_enable(int slot) /* switch VCC on */ val |= MAX1604_OP_SUS | MAX1604_VCCBON; - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1); udelay(500000); @@ -193,7 +193,7 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp) */ debug ("PCMCIA power OFF\n"); val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ; - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1); val = 0; diff --git a/board/lwmon5/kbd.c b/board/lwmon5/kbd.c index f3562b749b..97962daf93 100644 --- a/board/lwmon5/kbd.c +++ b/board/lwmon5/kbd.c @@ -98,7 +98,7 @@ static void kbd_init (void) uchar val, errcd; int i; - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); gd->arch.kbd_status = 0; diff --git a/board/mpl/pip405/pip405.c b/board/mpl/pip405/pip405.c index f39bb3572c..7c7690ff55 100644 --- a/board/mpl/pip405/pip405.c +++ b/board/mpl/pip405/pip405.c @@ -192,7 +192,7 @@ int board_early_init_f (void) #endif /* Read Serial Presence Detect Information */ - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); for (i = 0; i < 128; i++) datain[i] = 127; i2c_read(SPD_EEPROM_ADDRESS,0,1,datain,128); diff --git a/board/nvidia/common/board.c b/board/nvidia/common/board.c index 5f72c02572..126e56e97a 100644 --- a/board/nvidia/common/board.c +++ b/board/nvidia/common/board.c @@ -135,7 +135,7 @@ int board_init(void) power_det_init(); -#ifdef CONFIG_TEGRA_I2C +#ifdef CONFIG_SYS_I2C_TEGRA #ifndef CONFIG_SYS_I2C_INIT_BOARD #error "You must define CONFIG_SYS_I2C_INIT_BOARD to use i2c on Nvidia boards" #endif @@ -149,7 +149,7 @@ int board_init(void) debug("Memory controller init failed: %d\n", err); # endif # endif /* CONFIG_TEGRA_PMU */ -#endif /* CONFIG_TEGRA_I2C */ +#endif /* CONFIG_SYS_I2C_TEGRA */ #ifdef CONFIG_USB_EHCI_TEGRA pin_mux_usb(); diff --git a/board/pm826/pm826.c b/board/pm826/pm826.c index 109b20dec0..93bb1b4615 100644 --- a/board/pm826/pm826.c +++ b/board/pm826/pm826.c @@ -153,7 +153,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */ /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* PD17 */ /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* PD16 */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ #else diff --git a/board/pm828/pm828.c b/board/pm828/pm828.c index 26c3683ded..f446543fed 100644 --- a/board/pm828/pm828.c +++ b/board/pm828/pm828.c @@ -153,7 +153,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */ /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* PD17 */ /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* PD16 */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ #else diff --git a/board/sacsng/ioconfig.h b/board/sacsng/ioconfig.h index be1ce7c835..ac8f152e1f 100644 --- a/board/sacsng/ioconfig.h +++ b/board/sacsng/ioconfig.h @@ -187,7 +187,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD17 */ { CONF, SPEC, 1, DOUT, ACTV, 0 }, /* SPI_MOSI */ /* PD16 */ { CONF, SPEC, 1, DIN, ACTV, 0 }, /* SPI_MISO */ #endif -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PD15 */ { CONF, GPIO, 0, DOUT, OPEN, 1 }, /* I2C_SDA */ /* PD14 */ { CONF, GPIO, 0, DOUT, ACTV, 1 }, /* I2C_SCL */ #else diff --git a/board/sandburst/common/ppc440gx_i2c.c b/board/sandburst/common/ppc440gx_i2c.c deleted file mode 100644 index 1d7f17c39a..0000000000 --- a/board/sandburst/common/ppc440gx_i2c.c +++ /dev/null @@ -1,494 +0,0 @@ -/* - * Copyright (C) 2005 Sandburst Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Ported from arch/powerpc/cpu/ppc4xx/i2c.c by AS HARNOIS by - * Travis B. Sawyer - * Sandburst Corporation. - */ -#include -#include -#include -#include -#include -#include "ppc440gx_i2c.h" -#include - -#ifdef CONFIG_I2C_BUS1 - -#define IIC_OK 0 -#define IIC_NOK 1 -#define IIC_NOK_LA 2 /* Lost arbitration */ -#define IIC_NOK_ICT 3 /* Incomplete transfer */ -#define IIC_NOK_XFRA 4 /* Transfer aborted */ -#define IIC_NOK_DATA 5 /* No data in buffer */ -#define IIC_NOK_TOUT 6 /* Transfer timeout */ - -#define IIC_TIMEOUT 1 /* 1 second */ -#if defined(CONFIG_SYS_I2C_NOPROBES) -static uchar i2c_no_probes[] = CONFIG_SYS_I2C_NOPROBES; -#endif - -static struct ppc4xx_i2c *i2c = (struct ppc4xx_i2c *)I2C_REGISTERS_BUS1_BASE_ADDRESS; - -static void _i2c_bus1_reset (void) -{ - int i, status; - - /* Reset status register */ - /* write 1 in SCMP and IRQA to clear these fields */ - out_8 (IIC_STS1, 0x0A); - - /* write 1 in IRQP IRQD LA ICT XFRA to clear these fields */ - out_8 (IIC_EXTSTS1, 0x8F); - __asm__ volatile ("eieio"); - - /* - * Get current state, reset bus - * only if no transfers are pending. - */ - i = 10; - do { - /* Get status */ - status = in_8 (IIC_STS1); - udelay (500); /* 500us */ - i--; - } while ((status & IIC_STS_PT) && (i > 0)); - /* Soft reset controller */ - status = in_8 (IIC_XTCNTLSS1); - out_8 (IIC_XTCNTLSS1, (status | IIC_XTCNTLSS_SRST)); - __asm__ volatile ("eieio"); - - /* make sure where in initial state, data hi, clock hi */ - out_8 (IIC_DIRECTCNTL1, 0xC); - for (i = 0; i < 10; i++) { - if ((in_8 (IIC_DIRECTCNTL1) & 0x3) != 0x3) { - /* clock until we get to known state */ - out_8 (IIC_DIRECTCNTL1, 0x8); /* clock lo */ - udelay (100); /* 100us */ - out_8 (IIC_DIRECTCNTL1, 0xC); /* clock hi */ - udelay (100); /* 100us */ - } else { - break; - } - } - /* send start condition */ - out_8 (IIC_DIRECTCNTL1, 0x4); - udelay (1000); /* 1ms */ - /* send stop condition */ - out_8 (IIC_DIRECTCNTL1, 0xC); - udelay (1000); /* 1ms */ - /* Unreset controller */ - out_8 (IIC_XTCNTLSS1, (status & ~IIC_XTCNTLSS_SRST)); - udelay (1000); /* 1ms */ -} - -void i2c1_init (int speed, int slaveadd) -{ - sys_info_t sysInfo; - unsigned long freqOPB; - int val, divisor; - -#ifdef CONFIG_SYS_I2C_INIT_BOARD - /* call board specific i2c bus reset routine before accessing the */ - /* environment, which might be in a chip on that bus. For details */ - /* about this problem see doc/I2C_Edge_Conditions. */ - i2c_init_board(); -#endif - - /* Handle possible failed I2C state */ - /* FIXME: put this into i2c_init_board()? */ - _i2c_bus1_reset (); - - /* clear lo master address */ - out_8 (IIC_LMADR1, 0); - - /* clear hi master address */ - out_8 (IIC_HMADR1, 0); - - /* clear lo slave address */ - out_8 (IIC_LSADR1, 0); - - /* clear hi slave address */ - out_8 (IIC_HSADR1, 0); - - /* Clock divide Register */ - /* get OPB frequency */ - get_sys_info (&sysInfo); - freqOPB = sysInfo.freqPLB / sysInfo.pllOpbDiv; - /* set divisor according to freqOPB */ - divisor = (freqOPB - 1) / 10000000; - if (divisor == 0) - divisor = 1; - out_8 (IIC_CLKDIV1, divisor); - - /* no interrupts */ - out_8 (IIC_INTRMSK1, 0); - - /* clear transfer count */ - out_8 (IIC_XFRCNT1, 0); - - /* clear extended control & stat */ - /* write 1 in SRC SRS SWC SWS to clear these fields */ - out_8 (IIC_XTCNTLSS1, 0xF0); - - /* Mode Control Register - Flush Slave/Master data buffer */ - out_8 (IIC_MDCNTL1, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB); - __asm__ volatile ("eieio"); - - - val = in_8(IIC_MDCNTL1); - __asm__ volatile ("eieio"); - - /* Ignore General Call, slave transfers are ignored, - disable interrupts, exit unknown bus state, enable hold - SCL - 100kHz normaly or FastMode for 400kHz and above - */ - - val |= IIC_MDCNTL_EUBS|IIC_MDCNTL_HSCL; - if( speed >= 400000 ){ - val |= IIC_MDCNTL_FSM; - } - out_8 (IIC_MDCNTL1, val); - - /* clear control reg */ - out_8 (IIC_CNTL1, 0x00); - __asm__ volatile ("eieio"); - -} - -/* - This code tries to use the features of the 405GP i2c - controller. It will transfer up to 4 bytes in one pass - on the loop. It only does out_8(lbz) to the buffer when it - is possible to do out16(lhz) transfers. - - cmd_type is 0 for write 1 for read. - - addr_len can take any value from 0-255, it is only limited - by the char, we could make it larger if needed. If it is - 0 we skip the address write cycle. - - Typical case is a Write of an addr followd by a Read. The - IBM FAQ does not cover this. On the last byte of the write - we don't set the creg CHT bit, and on the first bytes of the - read we set the RPST bit. - - It does not support address only transfers, there must be - a data part. If you want to write the address yourself, put - it in the data pointer. - - It does not support transfer to/from address 0. - - It does not check XFRCNT. -*/ -static -int i2c_transfer1(unsigned char cmd_type, - unsigned char chip, - unsigned char addr[], - unsigned char addr_len, - unsigned char data[], - unsigned short data_len ) -{ - unsigned char* ptr; - int reading; - int tran,cnt; - int result; - int status; - int i; - uchar creg; - - if( data == 0 || data_len == 0 ){ - /*Don't support data transfer of no length or to address 0*/ - printf( "i2c_transfer: bad call\n" ); - return IIC_NOK; - } - if( addr && addr_len ){ - ptr = addr; - cnt = addr_len; - reading = 0; - }else{ - ptr = data; - cnt = data_len; - reading = cmd_type; - } - - /*Clear Stop Complete Bit*/ - out_8(IIC_STS1,IIC_STS_SCMP); - /* Check init */ - i=10; - do { - /* Get status */ - status = in_8(IIC_STS1); - __asm__ volatile("eieio"); - i--; - } while ((status & IIC_STS_PT) && (i>0)); - - if (status & IIC_STS_PT) { - result = IIC_NOK_TOUT; - return(result); - } - /*flush the Master/Slave Databuffers*/ - out_8(IIC_MDCNTL1, ((in_8(IIC_MDCNTL1))|IIC_MDCNTL_FMDB|IIC_MDCNTL_FSDB)); - /*need to wait 4 OPB clocks? code below should take that long*/ - - /* 7-bit adressing */ - out_8(IIC_HMADR1,0); - out_8(IIC_LMADR1, chip); - __asm__ volatile("eieio"); - - tran = 0; - result = IIC_OK; - creg = 0; - - while ( tran != cnt && (result == IIC_OK)) { - int bc,j; - - /* Control register = - Normal transfer, 7-bits adressing, Transfer up to bc bytes, Normal start, - Transfer is a sequence of transfers - */ - creg |= IIC_CNTL_PT; - - bc = (cnt - tran) > 4 ? 4 : - cnt - tran; - creg |= (bc-1)<<4; - /* if the real cmd type is write continue trans*/ - if ( (!cmd_type && (ptr == addr)) || ((tran+bc) != cnt) ) - creg |= IIC_CNTL_CHT; - - if (reading) - creg |= IIC_CNTL_READ; - else { - for(j=0; j0)); - - if (status & IIC_STS_ERR) { - result = IIC_NOK; - status = in_8 (IIC_EXTSTS1); - /* Lost arbitration? */ - if (status & IIC_EXTSTS_LA) - result = IIC_NOK_LA; - /* Incomplete transfer? */ - if (status & IIC_EXTSTS_ICT) - result = IIC_NOK_ICT; - /* Transfer aborted? */ - if (status & IIC_EXTSTS_XFRA) - result = IIC_NOK_XFRA; - } else if ( status & IIC_STS_PT) { - result = IIC_NOK_TOUT; - } - /* Command is reading => get buffer */ - if ((reading) && (result == IIC_OK)) { - /* Are there data in buffer */ - if (status & IIC_STS_MDBS) { - /* - even if we have data we have to wait 4OPB clocks - for it to hit the front of the FIFO, after that - we can just read. We should check XFCNT here and - if the FIFO is full there is no need to wait. - */ - udelay (1); - for(j=0;jed (i.e. there was a chip at that address which - * drove the data line low). - */ - return(i2c_transfer1 (1, chip << 1, 0,0, buf, 1) != 0); -} - - -int i2c_read1 (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - uchar xaddr[4]; - int ret; - - if ( alen > 4 ) { - printf ("I2C read: addr len %d not supported\n", alen); - return 1; - } - - if ( alen > 0 ) { - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - } - - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of - * address and the extra bits end up in the "chip address" - * bit slots. This makes a 24WC08 (1Kbyte) chip look like - * four 256 byte chips. - * - * Note that we consider the length of the address field to - * still be one byte because the extra address bits are - * hidden in the chip address. - */ - if( alen > 0 ) - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - if( (ret = i2c_transfer1( 1, chip<<1, &xaddr[4-alen], alen, buffer, len )) != 0) { - printf( "I2c read: failed %d\n", ret); - return 1; - } - return 0; -} - -int i2c_write1 (uchar chip, uint addr, int alen, uchar * buffer, int len) -{ - uchar xaddr[4]; - - if ( alen > 4 ) { - printf ("I2C write: addr len %d not supported\n", alen); - return 1; - - } - if ( alen > 0 ) { - xaddr[0] = (addr >> 24) & 0xFF; - xaddr[1] = (addr >> 16) & 0xFF; - xaddr[2] = (addr >> 8) & 0xFF; - xaddr[3] = addr & 0xFF; - } - -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW - /* - * EEPROM chips that implement "address overflow" are ones - * like Catalyst 24WC04/08/16 which has 9/10/11 bits of - * address and the extra bits end up in the "chip address" - * bit slots. This makes a 24WC08 (1Kbyte) chip look like - * four 256 byte chips. - * - * Note that we consider the length of the address field to - * still be one byte because the extra address bits are - * hidden in the chip address. - */ - if( alen > 0 ) - chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); -#endif - - return (i2c_transfer1( 0, chip<<1, &xaddr[4-alen], alen, buffer, len ) != 0); -} - -/*----------------------------------------------------------------------- - * Read a register - */ -uchar i2c_reg_read1(uchar i2c_addr, uchar reg) -{ - uchar buf; - - i2c_read1(i2c_addr, reg, 1, &buf, (uchar)1); - - return(buf); -} - -/*----------------------------------------------------------------------- - * Write a register - */ -void i2c_reg_write1(uchar i2c_addr, uchar reg, uchar val) -{ - i2c_write1(i2c_addr, reg, 1, &val, 1); -} - - -int do_i2c1_probe(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - int j; -#if defined(CONFIG_SYS_I2C_NOPROBES) - int k, skip; -#endif - - puts ("Valid chip addresses:"); - for(j = 0; j < 128; j++) { -#if defined(CONFIG_SYS_I2C_NOPROBES) - skip = 0; - for (k = 0; k < sizeof(i2c_no_probes); k++){ - if (j == i2c_no_probes[k]){ - skip = 1; - break; - } - } - if (skip) - continue; -#endif - if(i2c_probe1(j) == 0) { - printf(" %02X", j); - } - } - putc ('\n'); - -#if defined(CONFIG_SYS_I2C_NOPROBES) - puts ("Excluded chip addresses:"); - for( k = 0; k < sizeof(i2c_no_probes); k++ ) - printf(" %02X", i2c_no_probes[k] ); - putc ('\n'); -#endif - - return 0; -} - -U_BOOT_CMD( - iprobe1, 1, 1, do_i2c1_probe, - "probe to discover valid I2C chip addresses", - "" -); - -#endif /* CONFIG_I2C_BUS1 */ diff --git a/board/sandburst/common/ppc440gx_i2c.h b/board/sandburst/common/ppc440gx_i2c.h deleted file mode 100644 index b1179bcc4a..0000000000 --- a/board/sandburst/common/ppc440gx_i2c.h +++ /dev/null @@ -1,44 +0,0 @@ -/* - * Copyright (C) 2005 Sandburst Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Ported from i2c driver for ppc4xx by AS HARNOIS by - * Travis B. Sawyer - * Sandburst Corporation - */ -#include -#include -#include -#include - -#ifdef CONFIG_HARD_I2C - -#define I2C_BUS1_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x00000500) -#define I2C_REGISTERS_BUS1_BASE_ADDRESS I2C_BUS1_BASE_ADDR -#define IIC_MDBUF1 (&i2c->mdbuf) -#define IIC_SDBUF1 (&i2c->sdbuf) -#define IIC_LMADR1 (&i2c->lmadr) -#define IIC_HMADR1 (&i2c->hmadr) -#define IIC_CNTL1 (&i2c->cntl) -#define IIC_MDCNTL1 (&i2c->mdcntl) -#define IIC_STS1 (&i2c->sts) -#define IIC_EXTSTS1 (&i2c->extsts) -#define IIC_LSADR1 (&i2c->lsadr) -#define IIC_HSADR1 (&i2c->hsadr) -#define IIC_CLKDIV1 (&i2c->clkdiv) -#define IIC_INTRMSK1 (&i2c->intrmsk) -#define IIC_XFRCNT1 (&i2c->xfrcnt) -#define IIC_XTCNTLSS1 (&i2c->xtcntlss) -#define IIC_DIRECTCNTL1 (&i2c->directcntl) - -void i2c1_init (int speed, int slaveadd); -int i2c_probe1 (uchar chip); -int i2c_read1 (uchar chip, uint addr, int alen, uchar * buffer, int len); -int i2c_write1 (uchar chip, uint addr, int alen, uchar * buffer, int len); -uchar i2c_reg_read1(uchar i2c_addr, uchar reg); -void i2c_reg_write1(uchar i2c_addr, uchar reg, uchar val); - -#endif /* CONFIG_HARD_I2C */ diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c index 12334dfdd1..b579812ccf 100644 --- a/board/sandburst/common/sb_common.c +++ b/board/sandburst/common/sb_common.c @@ -10,7 +10,6 @@ #include #include #include -#include "ppc440gx_i2c.h" #include "sb_common.h" DECLARE_GLOBAL_DATA_PTR; @@ -68,7 +67,7 @@ unsigned short sbcommon_get_serial_number(void) /* Get the board serial number from eeprom */ /* Initialize I2C */ - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); /* Read 256 bytes in EEPROM */ i2c_read (0x50, 0, 1, buff, 0x100); @@ -94,85 +93,87 @@ void sbcommon_fans(void) * Attempt to turn on 2 of the fans... * Need to go through the bridge */ + i2c_set_bus_num(1); puts ("FANS: "); /* select fan4 through the bridge */ - i2c_reg_write1(0x73, /* addr */ - 0x00, /* reg */ - 0x08); /* val = bus 4 */ + i2c_reg_write(0x73, /* addr */ + 0x00, /* reg */ + 0x08); /* val = bus 4 */ /* Turn on FAN 4 */ - i2c_reg_write1(0x2e, - 1, - 0x80); + i2c_reg_write(0x2e, + 1, + 0x80); - i2c_reg_write1(0x2e, - 0, - 0x19); + i2c_reg_write(0x2e, + 0, + 0x19); /* Deselect bus 4 on the bridge */ - i2c_reg_write1(0x73, - 0x00, - 0x00); + i2c_reg_write(0x73, + 0x00, + 0x00); /* select fan3 through the bridge */ - i2c_reg_write1(0x73, /* addr */ - 0x00, /* reg */ - 0x04); /* val = bus 3 */ + i2c_reg_write(0x73, /* addr */ + 0x00, /* reg */ + 0x04); /* val = bus 3 */ /* Turn on FAN 3 */ - i2c_reg_write1(0x2e, - 1, - 0x80); + i2c_reg_write(0x2e, + 1, + 0x80); - i2c_reg_write1(0x2e, - 0, - 0x19); + i2c_reg_write(0x2e, + 0, + 0x19); /* Deselect bus 3 on the bridge */ - i2c_reg_write1(0x73, - 0x00, - 0x00); + i2c_reg_write(0x73, + 0x00, + 0x00); /* select fan2 through the bridge */ - i2c_reg_write1(0x73, /* addr */ - 0x00, /* reg */ - 0x02); /* val = bus 4 */ + i2c_reg_write(0x73, /* addr */ + 0x00, /* reg */ + 0x02); /* val = bus 4 */ /* Turn on FAN 2 */ - i2c_reg_write1(0x2e, - 1, - 0x80); + i2c_reg_write(0x2e, + 1, + 0x80); - i2c_reg_write1(0x2e, - 0, - 0x19); + i2c_reg_write(0x2e, + 0, + 0x19); /* Deselect bus 2 on the bridge */ - i2c_reg_write1(0x73, - 0x00, - 0x00); + i2c_reg_write(0x73, + 0x00, + 0x00); /* select fan1 through the bridge */ - i2c_reg_write1(0x73, /* addr */ - 0x00, /* reg */ - 0x01); /* val = bus 0 */ + i2c_reg_write(0x73, /* addr */ + 0x00, /* reg */ + 0x01); /* val = bus 0 */ /* Turn on FAN 1 */ - i2c_reg_write1(0x2e, - 1, - 0x80); + i2c_reg_write(0x2e, + 1, + 0x80); - i2c_reg_write1(0x2e, - 0, - 0x19); + i2c_reg_write(0x2e, + 0, + 0x19); /* Deselect bus 1 on the bridge */ - i2c_reg_write1(0x73, - 0x00, - 0x00); + i2c_reg_write(0x73, + 0x00, + 0x00); puts ("on\n"); + i2c_set_bus_num(0); return; @@ -303,7 +304,7 @@ void board_get_enetaddr(int macaddr_idx, uchar *enet) if (0 == macaddr_idx) { /* Initialize I2C */ - i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + i2c_set_bus_num(0); /* Read 256 bytes in EEPROM */ i2c_read (0x50, 0, 1, buff, 0x100); diff --git a/board/sandburst/common/sb_common.h b/board/sandburst/common/sb_common.h index c86061c414..8716eacd84 100644 --- a/board/sandburst/common/sb_common.h +++ b/board/sandburst/common/sb_common.h @@ -12,7 +12,6 @@ #include #include #include -#include "ppc440gx_i2c.h" /* * GPIO Settings diff --git a/board/sandburst/karef/Makefile b/board/sandburst/karef/Makefile index 9cceb47806..af758f947e 100644 --- a/board/sandburst/karef/Makefile +++ b/board/sandburst/karef/Makefile @@ -24,8 +24,7 @@ CFLAGS += -DBUILDUSER='"$(BUILDUSER)"' LIB = $(obj)lib$(BOARD).o -COBJS = $(BOARD).o ../common/flash.o ../common/ppc440gx_i2c.o \ - ../common/sb_common.o +COBJS = $(BOARD).o ../common/flash.o ../common/sb_common.o SOBJS = init.o diff --git a/board/sandburst/karef/karef.c b/board/sandburst/karef/karef.c index 93681c1871..683d68b933 100644 --- a/board/sandburst/karef/karef.c +++ b/board/sandburst/karef/karef.c @@ -16,7 +16,6 @@ #include #include #include "../common/sb_common.h" -#include "../common/ppc440gx_i2c.h" #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) || \ defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) #include @@ -322,11 +321,6 @@ int checkboard (void) ************************************************************************/ int misc_init_f (void) { - /* Turn on i2c bus 1 */ - puts ("I2C1: "); - i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - puts ("ready\n"); - /* Turn on fans 3 & 4 */ sbcommon_fans(); diff --git a/board/sandburst/metrobox/Makefile b/board/sandburst/metrobox/Makefile index 4dbd6ed314..163f2b98da 100644 --- a/board/sandburst/metrobox/Makefile +++ b/board/sandburst/metrobox/Makefile @@ -23,8 +23,7 @@ CFLAGS += -DBUILDUSER='"$(BUILDUSER)"' LIB = $(obj)lib$(BOARD).o -COBJS = $(BOARD).o ../common/flash.o ../common/ppc440gx_i2c.o \ - ../common/sb_common.o +COBJS = $(BOARD).o ../common/flash.o ../common/sb_common.o SOBJS = init.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) diff --git a/board/sandburst/metrobox/metrobox.c b/board/sandburst/metrobox/metrobox.c index 8d5079619e..5bc7f2f433 100644 --- a/board/sandburst/metrobox/metrobox.c +++ b/board/sandburst/metrobox/metrobox.c @@ -14,7 +14,6 @@ #include #include #include -#include "../common/ppc440gx_i2c.h" #include "../common/sb_common.h" #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) || \ defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3) @@ -289,11 +288,6 @@ int checkboard (void) ************************************************************************/ int misc_init_f (void) { - /* Turn on i2c bus 1 */ - puts ("I2C1: "); - i2c1_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - puts ("ready\n"); - /* Turn on fans */ sbcommon_fans(); diff --git a/board/tqc/tqm8260/tqm8260.c b/board/tqc/tqm8260/tqm8260.c index 669e99ddde..c361f188f7 100644 --- a/board/tqc/tqm8260/tqm8260.c +++ b/board/tqc/tqm8260/tqm8260.c @@ -144,7 +144,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ #else diff --git a/board/tqc/tqm8272/tqm8272.c b/board/tqc/tqm8272/tqm8272.c index b9dd4fa6b7..334fd6d74b 100644 --- a/board/tqc/tqm8272/tqm8272.c +++ b/board/tqc/tqm8272/tqm8272.c @@ -164,7 +164,7 @@ const iop_conf_t iop_conf_tab[4][32] = { /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ #else diff --git a/board/tqc/tqm8272/tqm8272.h b/board/tqc/tqm8272/tqm8272.h index fbdbff68de..2205d51b06 100644 --- a/board/tqc/tqm8272/tqm8272.h +++ b/board/tqc/tqm8272/tqm8272.h @@ -34,4 +34,4 @@ typedef struct{ static HWIB_INFO hwinf = {0, 0, 1, 0, 1, 0, 0, 0, 0, 8272, 0 ,0, 0, 0, 0, 0, 0, 0}; -#endif +#endif /* __CONFIG_H */ diff --git a/common/board_f.c b/common/board_f.c index 3f8766bd72..0ada1afe16 100644 --- a/common/board_f.c +++ b/common/board_f.c @@ -245,7 +245,7 @@ void __dram_init_banksize(void) void dram_init_banksize(void) __attribute__((weak, alias("__dram_init_banksize"))); -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) static int init_func_i2c(void) { puts("I2C: "); @@ -903,7 +903,7 @@ static init_fnc_t init_sequence_f[] = { misc_init_f, #endif INIT_FUNC_WATCHDOG_RESET -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) init_func_i2c, #endif #if defined(CONFIG_HARD_SPI) diff --git a/common/cmd_date.c b/common/cmd_date.c index f0e66862ff..e3491662bc 100644 --- a/common/cmd_date.c +++ b/common/cmd_date.c @@ -34,8 +34,13 @@ static int do_date(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) int old_bus; /* switch to correct I2C bus */ +#ifdef CONFIG_SYS_I2C + old_bus = i2c_get_bus_num(); + i2c_set_bus_num(CONFIG_SYS_RTC_BUS_NUM); +#else old_bus = I2C_GET_BUS(); I2C_SET_BUS(CONFIG_SYS_RTC_BUS_NUM); +#endif switch (argc) { case 2: /* set date & time */ @@ -81,7 +86,11 @@ static int do_date(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) } /* switch back to original I2C bus */ +#ifdef CONFIG_SYS_I2C + i2c_set_bus_num(old_bus); +#else I2C_SET_BUS(old_bus); +#endif return rcode; } diff --git a/common/cmd_dtt.c b/common/cmd_dtt.c index dc57744f89..7257f10fb1 100644 --- a/common/cmd_dtt.c +++ b/common/cmd_dtt.c @@ -57,8 +57,13 @@ int dtt_i2c(void) /* Force a compilation error, if there are more then 32 sensors */ BUILD_BUG_ON(sizeof(sensors) > 32); /* switch to correct I2C bus */ +#ifdef CONFIG_SYS_I2C + old_bus = i2c_get_bus_num(); + i2c_set_bus_num(CONFIG_SYS_DTT_BUS_NUM); +#else old_bus = I2C_GET_BUS(); I2C_SET_BUS(CONFIG_SYS_DTT_BUS_NUM); +#endif _initialize_dtt(); @@ -70,7 +75,11 @@ int dtt_i2c(void) printf("DTT%d: %i C\n", i + 1, dtt_get_temp(sensors[i])); /* switch back to original I2C bus */ +#ifdef CONFIG_SYS_I2C + i2c_set_bus_num(old_bus); +#else I2C_SET_BUS(old_bus); +#endif #endif return 0; diff --git a/common/cmd_eeprom.c b/common/cmd_eeprom.c index 1397636351..ef694d8f87 100644 --- a/common/cmd_eeprom.c +++ b/common/cmd_eeprom.c @@ -389,8 +389,7 @@ void eeprom_init (void) #if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C) spi_init_f (); #endif -#if defined(CONFIG_HARD_I2C) || \ - defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); #endif } diff --git a/common/cmd_i2c.c b/common/cmd_i2c.c index 1703ab41ac..29f5181baf 100644 --- a/common/cmd_i2c.c +++ b/common/cmd_i2c.c @@ -1,4 +1,9 @@ /* + * (C) Copyright 2009 + * Sergey Kubushyn, himself, ksi@koi8.net + * + * Changes for unified multibus/multiadapter I2C support. + * * (C) Copyright 2001 * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com. * @@ -69,6 +74,8 @@ #include #include +DECLARE_GLOBAL_DATA_PTR; + /* Display values from last command. * Memory modify remembered values are different from display memory. */ @@ -87,7 +94,7 @@ static uint i2c_mm_last_alen; * pairs. The following macros take care of this */ #if defined(CONFIG_SYS_I2C_NOPROBES) -#if defined(CONFIG_I2C_MULTI_BUS) +#if defined(CONFIG_SYS_I2C) || defined(CONFIG_I2C_MULTI_BUS) static struct { uchar bus; @@ -103,17 +110,7 @@ static uchar i2c_no_probes[] = CONFIG_SYS_I2C_NOPROBES; #define COMPARE_BUS(b,i) ((b) == 0) /* Make compiler happy */ #define COMPARE_ADDR(a,i) (i2c_no_probes[(i)] == (a)) #define NO_PROBE_ADDR(i) i2c_no_probes[(i)] -#endif /* CONFIG_MULTI_BUS */ - -#define NUM_ELEMENTS_NOPROBE (sizeof(i2c_no_probes)/sizeof(i2c_no_probes[0])) -#endif - -#if defined(CONFIG_I2C_MUX) -static I2C_MUX_DEVICE *i2c_mux_devices = NULL; -static int i2c_mux_busid = CONFIG_SYS_MAX_I2C_BUS; - -DECLARE_GLOBAL_DATA_PTR; - +#endif /* defined(CONFIG_SYS_I2C) */ #endif #define DISP_LINE_LEN 16 @@ -128,7 +125,6 @@ DECLARE_GLOBAL_DATA_PTR; __weak void i2c_init_board(void) { - return; } /* TODO: Implement architecture-specific get/set functions */ @@ -145,6 +141,11 @@ void i2c_init_board(void) * * Returns I2C bus speed in Hz. */ +#if !defined(CONFIG_SYS_I2C) +/* + * TODO: Implement architecture-specific get/set functions + * Should go away, if we switched completely to new multibus support + */ __weak unsigned int i2c_get_bus_speed(void) { @@ -172,6 +173,7 @@ int i2c_set_bus_speed(unsigned int speed) return 0; } +#endif /** * get_alen() - Small parser helper function to get address length @@ -684,7 +686,7 @@ static int do_i2c_probe (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv int found = 0; #if defined(CONFIG_SYS_I2C_NOPROBES) int k, skip; - uchar bus = GET_BUS_NUM; + unsigned int bus = GET_BUS_NUM; #endif /* NOPROBES */ if (argc == 2) @@ -697,7 +699,7 @@ static int do_i2c_probe (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv #if defined(CONFIG_SYS_I2C_NOPROBES) skip = 0; - for (k=0; k < NUM_ELEMENTS_NOPROBE; k++) { + for (k = 0; k < ARRAY_SIZE(i2c_no_probes); k++) { if (COMPARE_BUS(bus, k) && COMPARE_ADDR(j, k)) { skip = 1; break; @@ -715,7 +717,7 @@ static int do_i2c_probe (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv #if defined(CONFIG_SYS_I2C_NOPROBES) puts ("Excluded chip addresses:"); - for (k=0; k < NUM_ELEMENTS_NOPROBE; k++) { + for (k = 0; k < ARRAY_SIZE(i2c_no_probes); k++) { if (COMPARE_BUS(bus,k)) printf(" %02X", NO_PROBE_ADDR(k)); } @@ -1357,9 +1359,8 @@ int do_edid(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) } #endif /* CONFIG_I2C_EDID */ -#if defined(CONFIG_I2C_MUX) /** - * do_i2c_add_bus() - Handle the "i2c bus" command-line command + * do_i2c_show_bus() - Handle the "i2c bus" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count @@ -1367,35 +1368,55 @@ int do_edid(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) * * Returns zero always. */ -static int do_i2c_add_bus(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) +#if defined(CONFIG_SYS_I2C) +int do_i2c_show_bus(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { - int ret=0; + int i; +#ifndef CONFIG_SYS_I2C_DIRECT_BUS + int j; +#endif if (argc == 1) { /* show all busses */ - I2C_MUX *mux; - I2C_MUX_DEVICE *device = i2c_mux_devices; - - printf ("Busses reached over muxes:\n"); - while (device != NULL) { - printf ("Bus ID: %x\n", device->busid); - printf (" reached over Mux(es):\n"); - mux = device->mux; - while (mux != NULL) { - printf (" %s@%x ch: %x\n", mux->name, mux->chip, mux->channel); - mux = mux->next; + for (i = 0; i < CONFIG_SYS_NUM_I2C_BUSES; i++) { + printf("Bus %d:\t%s", i, I2C_ADAP_NR(i)->name); +#ifndef CONFIG_SYS_I2C_DIRECT_BUS + for (j = 0; j < CONFIG_SYS_I2C_MAX_HOPS; j++) { + if (i2c_bus[i].next_hop[j].chip == 0) + break; + printf("->%s@0x%2x:%d", + i2c_bus[i].next_hop[j].mux.name, + i2c_bus[i].next_hop[j].chip, + i2c_bus[i].next_hop[j].channel); } - device = device->next; +#endif + printf("\n"); } } else { - (void)i2c_mux_ident_muxstring ((uchar *)argv[1]); - ret = 0; + /* show specific bus */ + i = simple_strtoul(argv[1], NULL, 10); + if (i >= CONFIG_SYS_NUM_I2C_BUSES) { + printf("Invalid bus %d\n", i); + return -1; + } + printf("Bus %d:\t%s", i, I2C_ADAP_NR(i)->name); +#ifndef CONFIG_SYS_I2C_DIRECT_BUS + for (j = 0; j < CONFIG_SYS_I2C_MAX_HOPS; j++) { + if (i2c_bus[i].next_hop[j].chip == 0) + break; + printf("->%s@0x%2x:%d", + i2c_bus[i].next_hop[j].mux.name, + i2c_bus[i].next_hop[j].chip, + i2c_bus[i].next_hop[j].channel); + } +#endif + printf("\n"); } - return ret; -} -#endif /* CONFIG_I2C_MUX */ -#if defined(CONFIG_I2C_MULTI_BUS) + return 0; +} +#endif + /** * do_i2c_bus_num() - Handle the "i2c dev" command-line command * @cmdtp: Command data struct pointer @@ -1406,23 +1427,29 @@ static int do_i2c_add_bus(cmd_tbl_t * cmdtp, int flag, int argc, char * const ar * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. */ -static int do_i2c_bus_num(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) +#if defined(CONFIG_SYS_I2C) || defined(CONFIG_I2C_MULTI_BUS) +int do_i2c_bus_num(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { - int bus_idx, ret=0; + int ret = 0; + unsigned int bus_no; if (argc == 1) /* querying current setting */ printf("Current bus is %d\n", i2c_get_bus_num()); else { - bus_idx = simple_strtoul(argv[1], NULL, 10); - printf("Setting bus to %d\n", bus_idx); - ret = i2c_set_bus_num(bus_idx); + bus_no = simple_strtoul(argv[1], NULL, 10); + if (bus_no >= CONFIG_SYS_NUM_I2C_BUSES) { + printf("Invalid bus %d\n", bus_no); + return -1; + } + printf("Setting bus to %d\n", bus_no); + ret = i2c_set_bus_num(bus_no); if (ret) printf("Failure changing bus number (%d)\n", ret); } return ret; } -#endif /* CONFIG_I2C_MULTI_BUS */ +#endif /* defined(CONFIG_SYS_I2C) */ /** * do_i2c_bus_speed() - Handle the "i2c speed" command-line command @@ -1492,16 +1519,21 @@ static int do_i2c_nm(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) */ static int do_i2c_reset(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) { +#if defined(CONFIG_SYS_I2C) + i2c_init(I2C_ADAP->speed, I2C_ADAP->slaveaddr); +#else i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); +#endif return 0; } static cmd_tbl_t cmd_i2c_sub[] = { -#if defined(CONFIG_I2C_MUX) - U_BOOT_CMD_MKENT(bus, 1, 1, do_i2c_add_bus, "", ""), -#endif /* CONFIG_I2C_MUX */ +#if defined(CONFIG_SYS_I2C) + U_BOOT_CMD_MKENT(bus, 1, 1, do_i2c_show_bus, "", ""), +#endif U_BOOT_CMD_MKENT(crc32, 3, 1, do_i2c_crc, "", ""), -#if defined(CONFIG_I2C_MULTI_BUS) +#if defined(CONFIG_SYS_I2C) || \ + defined(CONFIG_I2C_MULTI_BUS) U_BOOT_CMD_MKENT(dev, 1, 1, do_i2c_bus_num, "", ""), #endif /* CONFIG_I2C_MULTI_BUS */ #if defined(CONFIG_I2C_EDID) @@ -1560,11 +1592,12 @@ static int do_i2c(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) /***************************************************/ #ifdef CONFIG_SYS_LONGHELP static char i2c_help_text[] = -#if defined(CONFIG_I2C_MUX) - "bus [muxtype:muxaddr:muxchannel] - add a new bus reached over muxes\ni2c " -#endif /* CONFIG_I2C_MUX */ +#if defined(CONFIG_SYS_I2C) + "bus [muxtype:muxaddr:muxchannel] - show I2C bus info\n" +#endif "crc32 chip address[.0, .1, .2] count - compute CRC32 checksum\n" -#if defined(CONFIG_I2C_MULTI_BUS) +#if defined(CONFIG_SYS_I2C) || \ + defined(CONFIG_I2C_MULTI_BUS) "i2c dev [dev] - show or set current I2C bus\n" #endif /* CONFIG_I2C_MULTI_BUS */ #if defined(CONFIG_I2C_EDID) @@ -1590,225 +1623,3 @@ U_BOOT_CMD( "I2C sub-system", i2c_help_text ); - -#if defined(CONFIG_I2C_MUX) -static int i2c_mux_add_device(I2C_MUX_DEVICE *dev) -{ - I2C_MUX_DEVICE *devtmp = i2c_mux_devices; - - if (i2c_mux_devices == NULL) { - i2c_mux_devices = dev; - return 0; - } - while (devtmp->next != NULL) - devtmp = devtmp->next; - - devtmp->next = dev; - return 0; -} - -I2C_MUX_DEVICE *i2c_mux_search_device(int id) -{ - I2C_MUX_DEVICE *device = i2c_mux_devices; - - while (device != NULL) { - if (device->busid == id) - return device; - device = device->next; - } - return NULL; -} - -/* searches in the buf from *pos the next ':'. - * returns: - * 0 if found (with *pos = where) - * < 0 if an error occured - * > 0 if the end of buf is reached - */ -static int i2c_mux_search_next (int *pos, uchar *buf, int len) -{ - while ((buf[*pos] != ':') && (*pos < len)) { - *pos += 1; - } - if (*pos >= len) - return 1; - if (buf[*pos] != ':') - return -1; - return 0; -} - -static int i2c_mux_get_busid (void) -{ - int tmp = i2c_mux_busid; - - i2c_mux_busid ++; - return tmp; -} - -/* Analyses a Muxstring and immediately sends the - commands to the muxes. Runs from flash. - */ -int i2c_mux_ident_muxstring_f (uchar *buf) -{ - int pos = 0; - int oldpos; - int ret = 0; - int len = strlen((char *)buf); - int chip; - uchar channel; - int was = 0; - - while (ret == 0) { - oldpos = pos; - /* search name */ - ret = i2c_mux_search_next(&pos, buf, len); - if (ret != 0) - printf ("ERROR\n"); - /* search address */ - pos ++; - oldpos = pos; - ret = i2c_mux_search_next(&pos, buf, len); - if (ret != 0) - printf ("ERROR\n"); - buf[pos] = 0; - chip = simple_strtoul((char *)&buf[oldpos], NULL, 16); - buf[pos] = ':'; - /* search channel */ - pos ++; - oldpos = pos; - ret = i2c_mux_search_next(&pos, buf, len); - if (ret < 0) - printf ("ERROR\n"); - was = 0; - if (buf[pos] != 0) { - buf[pos] = 0; - was = 1; - } - channel = simple_strtoul((char *)&buf[oldpos], NULL, 16); - if (was) - buf[pos] = ':'; - if (i2c_write(chip, 0, 0, &channel, 1) != 0) { - printf ("Error setting Mux: chip:%x channel: \ - %x\n", chip, channel); - return -1; - } - pos ++; - oldpos = pos; - - } - i2c_init_board(); - - return 0; -} - -/* Analyses a Muxstring and if this String is correct - * adds a new I2C Bus. - */ -I2C_MUX_DEVICE *i2c_mux_ident_muxstring (uchar *buf) -{ - I2C_MUX_DEVICE *device; - I2C_MUX *mux; - int pos = 0; - int oldpos; - int ret = 0; - int len = strlen((char *)buf); - int was = 0; - - device = (I2C_MUX_DEVICE *)malloc (sizeof(I2C_MUX_DEVICE)); - device->mux = NULL; - device->busid = i2c_mux_get_busid (); - device->next = NULL; - while (ret == 0) { - mux = (I2C_MUX *)malloc (sizeof(I2C_MUX)); - mux->next = NULL; - /* search name of mux */ - oldpos = pos; - ret = i2c_mux_search_next(&pos, buf, len); - if (ret != 0) - printf ("%s no name.\n", __FUNCTION__); - mux->name = (char *)malloc (pos - oldpos + 1); - memcpy (mux->name, &buf[oldpos], pos - oldpos); - mux->name[pos - oldpos] = 0; - /* search address */ - pos ++; - oldpos = pos; - ret = i2c_mux_search_next(&pos, buf, len); - if (ret != 0) - printf ("%s no mux address.\n", __FUNCTION__); - buf[pos] = 0; - mux->chip = simple_strtoul((char *)&buf[oldpos], NULL, 16); - buf[pos] = ':'; - /* search channel */ - pos ++; - oldpos = pos; - ret = i2c_mux_search_next(&pos, buf, len); - if (ret < 0) - printf ("%s no mux channel.\n", __FUNCTION__); - was = 0; - if (buf[pos] != 0) { - buf[pos] = 0; - was = 1; - } - mux->channel = simple_strtoul((char *)&buf[oldpos], NULL, 16); - if (was) - buf[pos] = ':'; - if (device->mux == NULL) - device->mux = mux; - else { - I2C_MUX *muxtmp = device->mux; - while (muxtmp->next != NULL) { - muxtmp = muxtmp->next; - } - muxtmp->next = mux; - } - pos ++; - oldpos = pos; - } - if (ret > 0) { - /* Add Device */ - i2c_mux_add_device (device); - return device; - } - - return NULL; -} - -int i2x_mux_select_mux(int bus) -{ - I2C_MUX_DEVICE *dev; - I2C_MUX *mux; - - if ((gd->flags & GD_FLG_RELOC) != GD_FLG_RELOC) { - /* select Default Mux Bus */ -#if defined(CONFIG_SYS_I2C_IVM_BUS) - i2c_mux_ident_muxstring_f ((uchar *)CONFIG_SYS_I2C_IVM_BUS); -#else - { - unsigned char *buf; - buf = (unsigned char *) getenv("EEprom_ivm"); - if (buf != NULL) - i2c_mux_ident_muxstring_f (buf); - } -#endif - return 0; - } - dev = i2c_mux_search_device(bus); - if (dev == NULL) - return -1; - - mux = dev->mux; - while (mux != NULL) { - /* do deblocking on each level of mux, before mux config */ - i2c_init_board(); - if (i2c_write(mux->chip, 0, 0, &mux->channel, 1) != 0) { - printf ("Error setting Mux: chip:%x channel: \ - %x\n", mux->chip, mux->channel); - return -1; - } - mux = mux->next; - } - /* do deblocking on each level of mux and after mux config */ - i2c_init_board(); - return 0; -} -#endif /* CONFIG_I2C_MUX */ diff --git a/common/env_eeprom.c b/common/env_eeprom.c index f5882bcfcf..149370f834 100644 --- a/common/env_eeprom.c +++ b/common/env_eeprom.c @@ -33,24 +33,8 @@ static int eeprom_bus_read(unsigned dev_addr, unsigned offset, #if defined(CONFIG_I2C_ENV_EEPROM_BUS) int old_bus = i2c_get_bus_num(); - if (gd->flags & GD_FLG_RELOC) { - if (env_eeprom_bus == -1) { - I2C_MUX_DEVICE *dev = NULL; - dev = i2c_mux_ident_muxstring( - (uchar *)CONFIG_I2C_ENV_EEPROM_BUS); - if (dev != NULL) - env_eeprom_bus = dev->busid; - else - printf("error adding env eeprom bus.\n"); - } - if (old_bus != env_eeprom_bus) { - i2c_set_bus_num(env_eeprom_bus); - old_bus = env_eeprom_bus; - } - } else { - rcode = i2c_mux_ident_muxstring_f( - (uchar *)CONFIG_I2C_ENV_EEPROM_BUS); - } + if (old_bus != CONFIG_I2C_ENV_EEPROM_BUS) + i2c_set_bus_num(CONFIG_I2C_ENV_EEPROM_BUS); #endif rcode = eeprom_read(dev_addr, offset, buffer, cnt); @@ -59,6 +43,7 @@ static int eeprom_bus_read(unsigned dev_addr, unsigned offset, if (old_bus != env_eeprom_bus) i2c_set_bus_num(old_bus); #endif + return rcode; } @@ -69,9 +54,12 @@ static int eeprom_bus_write(unsigned dev_addr, unsigned offset, #if defined(CONFIG_I2C_ENV_EEPROM_BUS) int old_bus = i2c_get_bus_num(); - rcode = i2c_mux_ident_muxstring_f((uchar *)CONFIG_I2C_ENV_EEPROM_BUS); + if (old_bus != CONFIG_I2C_ENV_EEPROM_BUS) + i2c_set_bus_num(CONFIG_I2C_ENV_EEPROM_BUS); #endif + rcode = eeprom_write(dev_addr, offset, buffer, cnt); + #if defined(CONFIG_I2C_ENV_EEPROM_BUS) i2c_set_bus_num(old_bus); #endif diff --git a/common/stdio.c b/common/stdio.c index 4ea8c0cedf..721e9a1444 100644 --- a/common/stdio.c +++ b/common/stdio.c @@ -1,4 +1,8 @@ /* + * Copyright (C) 2009 Sergey Kubushyn + * + * Changes for multibus/multiadapter I2C support. + * * (C) Copyright 2000 * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it * @@ -14,7 +18,8 @@ #ifdef CONFIG_LOGBUFFER #include #endif -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) + +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C) #include #endif @@ -194,9 +199,13 @@ int stdio_init (void) #ifdef CONFIG_ARM_DCC drv_arm_dcc_init (); #endif -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#ifdef CONFIG_SYS_I2C + i2c_init_all(); +#else +#if defined(CONFIG_HARD_I2C) i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); #endif +#endif #ifdef CONFIG_LCD drv_lcd_init (); #endif diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index 4ffbfdde3c..37ccbd1423 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -12,7 +12,6 @@ LIB := $(obj)libi2c.o COBJS-$(CONFIG_BFIN_TWI_I2C) += bfin-twi_i2c.o COBJS-$(CONFIG_DRIVER_DAVINCI_I2C) += davinci_i2c.o COBJS-$(CONFIG_DW_I2C) += designware_i2c.o -COBJS-$(CONFIG_FSL_I2C) += fsl_i2c.o COBJS-$(CONFIG_I2C_MVTWSI) += mvtwsi.o COBJS-$(CONFIG_I2C_MV) += mv_i2c.o COBJS-$(CONFIG_I2C_MXC) += mxc_i2c.o @@ -21,15 +20,18 @@ COBJS-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o COBJS-$(CONFIG_DRIVER_OMAP24XX_I2C) += omap24xx_i2c.o COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += omap24xx_i2c.o COBJS-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o -COBJS-$(CONFIG_PPC4XX_I2C) += ppc4xx_i2c.o COBJS-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o COBJS-$(CONFIG_S3C44B0_I2C) += s3c44b0_i2c.o -COBJS-$(CONFIG_SOFT_I2C) += soft_i2c.o -COBJS-$(CONFIG_TEGRA_I2C) += tegra_i2c.o COBJS-$(CONFIG_TSI108_I2C) += tsi108_i2c.o COBJS-$(CONFIG_U8500_I2C) += u8500_i2c.o COBJS-$(CONFIG_SH_I2C) += sh_i2c.o COBJS-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o +COBJS-$(CONFIG_SYS_I2C) += i2c_core.o +COBJS-$(CONFIG_SYS_I2C_FSL) += fsl_i2c.o +COBJS-$(CONFIG_SYS_I2C_FTI2C010) += fti2c010.o +COBJS-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o +COBJS-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o +COBJS-$(CONFIG_SYS_I2C_TEGRA) += tegra_i2c.o COBJS-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o COBJS := $(COBJS-y) diff --git a/drivers/i2c/fsl_i2c.c b/drivers/i2c/fsl_i2c.c index 5d7e010319..38455e1c66 100644 --- a/drivers/i2c/fsl_i2c.c +++ b/drivers/i2c/fsl_i2c.c @@ -1,6 +1,9 @@ /* * Copyright 2006,2009 Freescale Semiconductor, Inc. * + * 2012, Heiko Schocher, DENX Software Engineering, hs@denx.de. + * Changes for multibus/multiadapter I2C support. + * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * Version 2 as published by the Free Software Foundation. @@ -17,12 +20,8 @@ */ #include - -#ifdef CONFIG_HARD_I2C - #include #include /* Functional interface */ - #include #include /* HW definitions */ @@ -47,25 +46,10 @@ DECLARE_GLOBAL_DATA_PTR; -/* Initialize the bus pointer to whatever one the SPD EEPROM is on. - * Default is bus 0. This is necessary because the DDR initialization - * runs from ROM, and we can't switch buses because we can't modify - * the global variables. - */ -#ifndef CONFIG_SYS_SPD_BUS_NUM -#define CONFIG_SYS_SPD_BUS_NUM 0 -#endif -static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = CONFIG_SYS_SPD_BUS_NUM; -#if defined(CONFIG_I2C_MUX) -static unsigned int i2c_bus_num_mux __attribute__ ((section ("data"))) = 0; -#endif - -static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SPEED}; - static const struct fsl_i2c *i2c_dev[2] = { - (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET), -#ifdef CONFIG_SYS_I2C2_OFFSET - (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET) + (struct fsl_i2c *)(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_I2C_OFFSET), +#ifdef CONFIG_SYS_FSL_I2C2_OFFSET + (struct fsl_i2c *)(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_I2C2_OFFSET) #endif }; @@ -222,12 +206,9 @@ static unsigned int get_i2c_clock(int bus) return gd->arch.i2c1_clk; /* I2C1 clock */ } -void -i2c_init(int speed, int slaveadd) +static void fsl_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) { const struct fsl_i2c *dev; - unsigned int temp; - int bus_num, i; #ifdef CONFIG_SYS_I2C_INIT_BOARD /* Call board specific i2c bus reset routine before accessing the @@ -236,23 +217,14 @@ i2c_init(int speed, int slaveadd) */ i2c_init_board(); #endif -#ifdef CONFIG_SYS_I2C2_OFFSET - bus_num = 2; -#else - bus_num = 1; -#endif - for (i = 0; i < bus_num; i++) { - dev = i2c_dev[i]; + dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; - writeb(0, &dev->cr); /* stop I2C controller */ - udelay(5); /* let it shutdown in peace */ - temp = set_i2c_bus_speed(dev, get_i2c_clock(i), speed); - if (gd->flags & GD_FLG_RELOC) - i2c_bus_speed[i] = temp; - writeb(slaveadd << 1, &dev->adr);/* write slave address */ - writeb(0x0, &dev->sr); /* clear status register */ - writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ - } + writeb(0, &dev->cr); /* stop I2C controller */ + udelay(5); /* let it shutdown in peace */ + set_i2c_bus_speed(dev, get_i2c_clock(adap->hwadapnr), speed); + writeb(slaveadd << 1, &dev->adr);/* write slave address */ + writeb(0x0, &dev->sr); /* clear status register */ + writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ #ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT /* Call board specific i2c bus reset routine AFTER the bus has been @@ -265,12 +237,13 @@ i2c_init(int speed, int slaveadd) } static int -i2c_wait4bus(void) +i2c_wait4bus(struct i2c_adapter *adap) { + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; unsigned long long timeval = get_ticks(); const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT); - while (readb(&i2c_dev[i2c_bus_num]->sr) & I2C_SR_MBB) { + while (readb(&dev->sr) & I2C_SR_MBB) { if ((get_ticks() - timeval) > timeout) return -1; } @@ -279,20 +252,21 @@ i2c_wait4bus(void) } static __inline__ int -i2c_wait(int write) +i2c_wait(struct i2c_adapter *adap, int write) { u32 csr; unsigned long long timeval = get_ticks(); const unsigned long long timeout = usec2ticks(CONFIG_I2C_TIMEOUT); + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; do { - csr = readb(&i2c_dev[i2c_bus_num]->sr); + csr = readb(&dev->sr); if (!(csr & I2C_SR_MIF)) continue; /* Read again to allow register to stabilise */ - csr = readb(&i2c_dev[i2c_bus_num]->sr); + csr = readb(&dev->sr); - writeb(0x0, &i2c_dev[i2c_bus_num]->sr); + writeb(0x0, &dev->sr); if (csr & I2C_SR_MAL) { debug("i2c_wait: MAL\n"); @@ -317,29 +291,32 @@ i2c_wait(int write) } static __inline__ int -i2c_write_addr (u8 dev, u8 dir, int rsta) +i2c_write_addr(struct i2c_adapter *adap, u8 dev, u8 dir, int rsta) { + struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; + writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX | (rsta ? I2C_CR_RSTA : 0), - &i2c_dev[i2c_bus_num]->cr); + &device->cr); - writeb((dev << 1) | dir, &i2c_dev[i2c_bus_num]->dr); + writeb((dev << 1) | dir, &device->dr); - if (i2c_wait(I2C_WRITE_BIT) < 0) + if (i2c_wait(adap, I2C_WRITE_BIT) < 0) return 0; return 1; } static __inline__ int -__i2c_write(u8 *data, int length) +__i2c_write(struct i2c_adapter *adap, u8 *data, int length) { + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; int i; for (i = 0; i < length; i++) { - writeb(data[i], &i2c_dev[i2c_bus_num]->dr); + writeb(data[i], &dev->dr); - if (i2c_wait(I2C_WRITE_BIT) < 0) + if (i2c_wait(adap, I2C_WRITE_BIT) < 0) break; } @@ -347,57 +324,60 @@ __i2c_write(u8 *data, int length) } static __inline__ int -__i2c_read(u8 *data, int length) +__i2c_read(struct i2c_adapter *adap, u8 *data, int length) { + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; int i; writeb(I2C_CR_MEN | I2C_CR_MSTA | ((length == 1) ? I2C_CR_TXAK : 0), - &i2c_dev[i2c_bus_num]->cr); + &dev->cr); /* dummy read */ - readb(&i2c_dev[i2c_bus_num]->dr); + readb(&dev->dr); for (i = 0; i < length; i++) { - if (i2c_wait(I2C_READ_BIT) < 0) + if (i2c_wait(adap, I2C_READ_BIT) < 0) break; /* Generate ack on last next to last byte */ if (i == length - 2) writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_TXAK, - &i2c_dev[i2c_bus_num]->cr); + &dev->cr); /* Do not generate stop on last byte */ if (i == length - 1) writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX, - &i2c_dev[i2c_bus_num]->cr); + &dev->cr); - data[i] = readb(&i2c_dev[i2c_bus_num]->dr); + data[i] = readb(&dev->dr); } return i; } -int -i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) +static int +fsl_i2c_read(struct i2c_adapter *adap, u8 dev, uint addr, int alen, u8 *data, + int length) { + struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; int i = -1; /* signal error */ u8 *a = (u8*)&addr; - if (i2c_wait4bus() < 0) + if (i2c_wait4bus(adap) < 0) return -1; if ((!length || alen > 0) - && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0 - && __i2c_write(&a[4 - alen], alen) == alen) + && i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0 + && __i2c_write(adap, &a[4 - alen], alen) == alen) i = 0; /* No error so far */ if (length && - i2c_write_addr(dev, I2C_READ_BIT, alen ? 1 : 0) != 0) - i = __i2c_read(data, length); + i2c_write_addr(adap, dev, I2C_READ_BIT, alen ? 1 : 0) != 0) + i = __i2c_read(adap, data, length); - writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); + writeb(I2C_CR_MEN, &device->cr); - if (i2c_wait4bus()) /* Wait until STOP */ + if (i2c_wait4bus(adap)) /* Wait until STOP */ debug("i2c_read: wait4bus timed out\n"); if (i == length) @@ -406,20 +386,22 @@ i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) return -1; } -int -i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) +static int +fsl_i2c_write(struct i2c_adapter *adap, u8 dev, uint addr, int alen, + u8 *data, int length) { + struct fsl_i2c *device = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; int i = -1; /* signal error */ u8 *a = (u8*)&addr; - if (i2c_wait4bus() >= 0 - && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0 - && __i2c_write(&a[4 - alen], alen) == alen) { - i = __i2c_write(data, length); + if (i2c_wait4bus(adap) >= 0 && + i2c_write_addr(adap, dev, I2C_WRITE_BIT, 0) != 0 && + __i2c_write(adap, &a[4 - alen], alen) == alen) { + i = __i2c_write(adap, data, length); } - writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); - if (i2c_wait4bus()) /* Wait until STOP */ + writeb(I2C_CR_MEN, &device->cr); + if (i2c_wait4bus(adap)) /* Wait until STOP */ debug("i2c_write: wait4bus timed out\n"); if (i == length) @@ -428,72 +410,42 @@ i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) return -1; } -int -i2c_probe(uchar chip) +static int +fsl_i2c_probe(struct i2c_adapter *adap, uchar chip) { + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; /* For unknow reason the controller will ACK when * probing for a slave with the same address, so skip * it. */ - if (chip == (readb(&i2c_dev[i2c_bus_num]->adr) >> 1)) + if (chip == (readb(&dev->adr) >> 1)) return -1; - return i2c_read(chip, 0, 0, NULL, 0); + return fsl_i2c_read(adap, chip, 0, 0, NULL, 0); } -int i2c_set_bus_num(unsigned int bus) +static unsigned int fsl_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) { -#if defined(CONFIG_I2C_MUX) - if (bus < CONFIG_SYS_MAX_I2C_BUS) { - i2c_bus_num = bus; - } else { - int ret; + struct fsl_i2c *dev = (struct fsl_i2c *)i2c_dev[adap->hwadapnr]; - ret = i2x_mux_select_mux(bus); - if (ret) - return ret; - i2c_bus_num = 0; - } - i2c_bus_num_mux = bus; -#else -#ifdef CONFIG_SYS_I2C2_OFFSET - if (bus > 1) { -#else - if (bus > 0) { -#endif - return -1; - } - - i2c_bus_num = bus; -#endif - return 0; -} - -int i2c_set_bus_speed(unsigned int speed) -{ - unsigned int i2c_clk = (i2c_bus_num == 1) - ? gd->arch.i2c2_clk : gd->arch.i2c1_clk; - - writeb(0, &i2c_dev[i2c_bus_num]->cr); /* stop controller */ - i2c_bus_speed[i2c_bus_num] = - set_i2c_bus_speed(i2c_dev[i2c_bus_num], i2c_clk, speed); - writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); /* start controller */ + writeb(0, &dev->cr); /* stop controller */ + set_i2c_bus_speed(dev, get_i2c_clock(adap->hwadapnr), speed); + writeb(I2C_CR_MEN, &dev->cr); /* start controller */ return 0; } -unsigned int i2c_get_bus_num(void) -{ -#if defined(CONFIG_I2C_MUX) - return i2c_bus_num_mux; -#else - return i2c_bus_num; +/* + * Register fsl i2c adapters + */ +U_BOOT_I2C_ADAP_COMPLETE(fsl_0, fsl_i2c_init, fsl_i2c_probe, fsl_i2c_read, + fsl_i2c_write, fsl_i2c_set_bus_speed, + CONFIG_SYS_FSL_I2C_SPEED, CONFIG_SYS_FSL_I2C_SLAVE, + 0) +#ifdef CONFIG_SYS_FSL_I2C2_OFFSET +U_BOOT_I2C_ADAP_COMPLETE(fsl_1, fsl_i2c_init, fsl_i2c_probe, fsl_i2c_read, + fsl_i2c_write, fsl_i2c_set_bus_speed, + CONFIG_SYS_FSL_I2C2_SPEED, CONFIG_SYS_FSL_I2C2_SLAVE, + 1) #endif -} - -unsigned int i2c_get_bus_speed(void) -{ - return i2c_bus_speed[i2c_bus_num]; -} - -#endif /* CONFIG_HARD_I2C */ diff --git a/drivers/i2c/fti2c010.c b/drivers/i2c/fti2c010.c new file mode 100644 index 0000000000..24c4bb53fa --- /dev/null +++ b/drivers/i2c/fti2c010.c @@ -0,0 +1,369 @@ +/* + * Faraday I2C Controller + * + * (C) Copyright 2010 Faraday Technology + * Dante Su + * + * This file is released under the terms of GPL v2 and any later version. + * See the file COPYING in the root directory of the source tree for details. + */ + +#include +#include +#include + +#include "fti2c010.h" + +#ifndef CONFIG_HARD_I2C +#error "fti2c010: CONFIG_HARD_I2C is not defined" +#endif + +#ifndef CONFIG_SYS_I2C_SPEED +#define CONFIG_SYS_I2C_SPEED 50000 +#endif + +#ifndef CONFIG_FTI2C010_FREQ +#define CONFIG_FTI2C010_FREQ clk_get_rate("I2C") +#endif + +/* command timeout */ +#define CFG_CMD_TIMEOUT 10 /* ms */ + +/* 7-bit chip address + 1-bit read/write */ +#define I2C_RD(chip) ((((chip) << 1) & 0xff) | 1) +#define I2C_WR(chip) (((chip) << 1) & 0xff) + +struct fti2c010_chip { + void __iomem *regs; + uint bus; + uint speed; +}; + +static struct fti2c010_chip chip_list[] = { + { + .bus = 0, + .regs = (void __iomem *)CONFIG_FTI2C010_BASE, + }, +#ifdef CONFIG_I2C_MULTI_BUS +# ifdef CONFIG_FTI2C010_BASE1 + { + .bus = 1, + .regs = (void __iomem *)CONFIG_FTI2C010_BASE1, + }, +# endif +# ifdef CONFIG_FTI2C010_BASE2 + { + .bus = 2, + .regs = (void __iomem *)CONFIG_FTI2C010_BASE2, + }, +# endif +# ifdef CONFIG_FTI2C010_BASE3 + { + .bus = 3, + .regs = (void __iomem *)CONFIG_FTI2C010_BASE3, + }, +# endif +#endif /* #ifdef CONFIG_I2C_MULTI_BUS */ +}; + +static struct fti2c010_chip *curr = chip_list; + +static int fti2c010_wait(uint32_t mask) +{ + int ret = -1; + uint32_t stat, ts; + struct fti2c010_regs *regs = curr->regs; + + for (ts = get_timer(0); get_timer(ts) < CFG_CMD_TIMEOUT; ) { + stat = readl(®s->sr); + if ((stat & mask) == mask) { + ret = 0; + break; + } + } + + return ret; +} + +/* + * u-boot I2C API + */ + +/* + * Initialization, must be called once on start up, may be called + * repeatedly to change the speed and slave addresses. + */ +void i2c_init(int speed, int slaveaddr) +{ + if (speed || !curr->speed) + i2c_set_bus_speed(speed); + + /* if slave mode disabled */ + if (!slaveaddr) + return; + + /* + * TODO: + * Implement slave mode, but is it really necessary? + */ +} + +/* + * Probe the given I2C chip address. Returns 0 if a chip responded, + * not 0 on failure. + */ +int i2c_probe(uchar chip) +{ + int ret; + struct fti2c010_regs *regs = curr->regs; + + i2c_init(0, 0); + + /* 1. Select slave device (7bits Address + 1bit R/W) */ + writel(I2C_WR(chip), ®s->dr); + writel(CR_ENABLE | CR_TBEN | CR_START, ®s->cr); + ret = fti2c010_wait(SR_DT); + if (ret) + return ret; + + /* 2. Select device register */ + writel(0, ®s->dr); + writel(CR_ENABLE | CR_TBEN, ®s->cr); + ret = fti2c010_wait(SR_DT); + + return ret; +} + +/* + * Read/Write interface: + * chip: I2C chip address, range 0..127 + * addr: Memory (register) address within the chip + * alen: Number of bytes to use for addr (typically 1, 2 for larger + * memories, 0 for register type devices with only one + * register) + * buffer: Where to read/write the data + * len: How many bytes to read/write + * + * Returns: 0 on success, not 0 on failure + */ +int i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len) +{ + int ret, pos; + uchar paddr[4]; + struct fti2c010_regs *regs = curr->regs; + + i2c_init(0, 0); + + paddr[0] = (addr >> 0) & 0xFF; + paddr[1] = (addr >> 8) & 0xFF; + paddr[2] = (addr >> 16) & 0xFF; + paddr[3] = (addr >> 24) & 0xFF; + + /* + * Phase A. Set register address + */ + + /* A.1 Select slave device (7bits Address + 1bit R/W) */ + writel(I2C_WR(chip), ®s->dr); + writel(CR_ENABLE | CR_TBEN | CR_START, ®s->cr); + ret = fti2c010_wait(SR_DT); + if (ret) + return ret; + + /* A.2 Select device register */ + for (pos = 0; pos < alen; ++pos) { + uint32_t ctrl = CR_ENABLE | CR_TBEN; + + writel(paddr[pos], ®s->dr); + writel(ctrl, ®s->cr); + ret = fti2c010_wait(SR_DT); + if (ret) + return ret; + } + + /* + * Phase B. Get register data + */ + + /* B.1 Select slave device (7bits Address + 1bit R/W) */ + writel(I2C_RD(chip), ®s->dr); + writel(CR_ENABLE | CR_TBEN | CR_START, ®s->cr); + ret = fti2c010_wait(SR_DT); + if (ret) + return ret; + + /* B.2 Get register data */ + for (pos = 0; pos < len; ++pos) { + uint32_t ctrl = CR_ENABLE | CR_TBEN; + uint32_t stat = SR_DR; + + if (pos == len - 1) { + ctrl |= CR_NAK | CR_STOP; + stat |= SR_ACK; + } + writel(ctrl, ®s->cr); + ret = fti2c010_wait(stat); + if (ret) + break; + buf[pos] = (uchar)(readl(®s->dr) & 0xFF); + } + + return ret; +} + +/* + * Read/Write interface: + * chip: I2C chip address, range 0..127 + * addr: Memory (register) address within the chip + * alen: Number of bytes to use for addr (typically 1, 2 for larger + * memories, 0 for register type devices with only one + * register) + * buffer: Where to read/write the data + * len: How many bytes to read/write + * + * Returns: 0 on success, not 0 on failure + */ +int i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len) +{ + int ret, pos; + uchar paddr[4]; + struct fti2c010_regs *regs = curr->regs; + + i2c_init(0, 0); + + paddr[0] = (addr >> 0) & 0xFF; + paddr[1] = (addr >> 8) & 0xFF; + paddr[2] = (addr >> 16) & 0xFF; + paddr[3] = (addr >> 24) & 0xFF; + + /* + * Phase A. Set register address + * + * A.1 Select slave device (7bits Address + 1bit R/W) + */ + writel(I2C_WR(chip), ®s->dr); + writel(CR_ENABLE | CR_TBEN | CR_START, ®s->cr); + ret = fti2c010_wait(SR_DT); + if (ret) + return ret; + + /* A.2 Select device register */ + for (pos = 0; pos < alen; ++pos) { + uint32_t ctrl = CR_ENABLE | CR_TBEN; + + writel(paddr[pos], ®s->dr); + writel(ctrl, ®s->cr); + ret = fti2c010_wait(SR_DT); + if (ret) + return ret; + } + + /* + * Phase B. Set register data + */ + for (pos = 0; pos < len; ++pos) { + uint32_t ctrl = CR_ENABLE | CR_TBEN; + + if (pos == len - 1) + ctrl |= CR_STOP; + writel(buf[pos], ®s->dr); + writel(ctrl, ®s->cr); + ret = fti2c010_wait(SR_DT); + if (ret) + break; + } + + return ret; +} + +/* + * Functions for setting the current I2C bus and its speed + */ +#ifdef CONFIG_I2C_MULTI_BUS + +/* + * i2c_set_bus_num: + * + * Change the active I2C bus. Subsequent read/write calls will + * go to this one. + * + * bus - bus index, zero based + * + * Returns: 0 on success, not 0 on failure + */ +int i2c_set_bus_num(uint bus) +{ + if (bus >= ARRAY_SIZE(chip_list)) + return -1; + curr = chip_list + bus; + i2c_init(0, 0); + return 0; +} + +/* + * i2c_get_bus_num: + * + * Returns index of currently active I2C bus. Zero-based. + */ + +uint i2c_get_bus_num(void) +{ + return curr->bus; +} + +#endif /* #ifdef CONFIG_I2C_MULTI_BUS */ + +/* + * i2c_set_bus_speed: + * + * Change the speed of the active I2C bus + * + * speed - bus speed in Hz + * + * Returns: 0 on success, not 0 on failure + */ +int i2c_set_bus_speed(uint speed) +{ + struct fti2c010_regs *regs = curr->regs; + uint clk = CONFIG_FTI2C010_FREQ; + uint gsr = 0, tsr = 32; + uint spd, div; + + if (!speed) + speed = CONFIG_SYS_I2C_SPEED; + + for (div = 0; div < 0x3ffff; ++div) { + /* SCLout = PCLK/(2*(COUNT + 2) + GSR) */ + spd = clk / (2 * (div + 2) + gsr); + if (spd <= speed) + break; + } + + if (curr->speed == spd) + return 0; + + writel(CR_I2CRST, ®s->cr); + mdelay(100); + if (readl(®s->cr) & CR_I2CRST) { + printf("fti2c010: reset timeout\n"); + return -1; + } + + curr->speed = spd; + + writel(TGSR_GSR(gsr) | TGSR_TSR(tsr), ®s->tgsr); + writel(CDR_DIV(div), ®s->cdr); + + return 0; +} + +/* + * i2c_get_bus_speed: + * + * Returns speed of currently active I2C bus in Hz + */ + +uint i2c_get_bus_speed(void) +{ + return curr->speed; +} diff --git a/drivers/i2c/fti2c010.h b/drivers/i2c/fti2c010.h new file mode 100644 index 0000000000..18aec2c976 --- /dev/null +++ b/drivers/i2c/fti2c010.h @@ -0,0 +1,81 @@ +/* + * Faraday I2C Controller + * + * (C) Copyright 2010 Faraday Technology + * Dante Su + * + * This file is released under the terms of GPL v2 and any later version. + * See the file COPYING in the root directory of the source tree for details. + */ + +#ifndef __FTI2C010_H +#define __FTI2C010_H + +/* + * FTI2C010 registers + */ +struct fti2c010_regs { + uint32_t cr; /* 0x00: control register */ + uint32_t sr; /* 0x04: status register */ + uint32_t cdr; /* 0x08: clock division register */ + uint32_t dr; /* 0x0c: data register */ + uint32_t sar; /* 0x10: slave address register */ + uint32_t tgsr;/* 0x14: time & glitch suppression register */ + uint32_t bmr; /* 0x18: bus monitor register */ + uint32_t rsvd[5]; + uint32_t revr;/* 0x30: revision register */ +}; + +/* + * control register + */ +#define CR_ALIRQ 0x2000 /* arbitration lost interrupt (master) */ +#define CR_SAMIRQ 0x1000 /* slave address match interrupt (slave) */ +#define CR_STOPIRQ 0x800 /* stop condition interrupt (slave) */ +#define CR_NAKRIRQ 0x400 /* NACK response interrupt (master) */ +#define CR_DRIRQ 0x200 /* rx interrupt (both) */ +#define CR_DTIRQ 0x100 /* tx interrupt (both) */ +#define CR_TBEN 0x80 /* tx enable (both) */ +#define CR_NAK 0x40 /* NACK (both) */ +#define CR_STOP 0x20 /* stop (master) */ +#define CR_START 0x10 /* start (master) */ +#define CR_GCEN 0x8 /* general call support (slave) */ +#define CR_SCLEN 0x4 /* enable clock out (master) */ +#define CR_I2CEN 0x2 /* enable I2C (both) */ +#define CR_I2CRST 0x1 /* reset I2C (both) */ +#define CR_ENABLE \ + (CR_ALIRQ | CR_NAKRIRQ | CR_DRIRQ | CR_DTIRQ | CR_SCLEN | CR_I2CEN) + +/* + * status register + */ +#define SR_CLRAL 0x400 /* clear arbitration lost */ +#define SR_CLRGC 0x200 /* clear general call */ +#define SR_CLRSAM 0x100 /* clear slave address match */ +#define SR_CLRSTOP 0x80 /* clear stop */ +#define SR_CLRNAKR 0x40 /* clear NACK respond */ +#define SR_DR 0x20 /* rx ready */ +#define SR_DT 0x10 /* tx done */ +#define SR_BB 0x8 /* bus busy */ +#define SR_BUSY 0x4 /* chip busy */ +#define SR_ACK 0x2 /* ACK/NACK received */ +#define SR_RW 0x1 /* set when master-rx or slave-tx mode */ + +/* + * clock division register + */ +#define CDR_DIV(n) ((n) & 0x3ffff) + +/* + * time & glitch suppression register + */ +#define TGSR_GSR(n) (((n) & 0x7) << 10) +#define TGSR_TSR(n) ((n) & 0x3ff) + +/* + * bus monitor register + */ +#define BMR_SCL 0x2 /* SCL is pull-up */ +#define BMR_SDA 0x1 /* SDA is pull-up */ + +#endif /* __FTI2C010_H */ diff --git a/drivers/i2c/i2c_core.c b/drivers/i2c/i2c_core.c new file mode 100644 index 0000000000..3c01893c9c --- /dev/null +++ b/drivers/i2c/i2c_core.c @@ -0,0 +1,414 @@ +/* + * Copyright (C) 2009 Sergey Kubushyn + * + * (C) Copyright 2012 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * Multibus/multiadapter I2C core functions (wrappers) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include +#include + +struct i2c_adapter *i2c_get_adapter(int index) +{ + struct i2c_adapter *i2c_adap_p = ll_entry_start(struct i2c_adapter, + i2c); + int max = ll_entry_count(struct i2c_adapter, i2c); + int i; + + if (index >= max) { + printf("Error, wrong i2c adapter %d max %d possible\n", + index, max); + return i2c_adap_p; + } + if (index == 0) + return i2c_adap_p; + + for (i = 0; i < index; i++) + i2c_adap_p++; + + return i2c_adap_p; +} + +#if !defined(CONFIG_SYS_I2C_DIRECT_BUS) +struct i2c_bus_hose i2c_bus[CONFIG_SYS_NUM_I2C_BUSES] = + CONFIG_SYS_I2C_BUSES; +#endif + +DECLARE_GLOBAL_DATA_PTR; + +void i2c_reloc_fixup(void) +{ +#if defined(CONFIG_NEEDS_MANUAL_RELOC) + struct i2c_adapter *i2c_adap_p = ll_entry_start(struct i2c_adapter, + i2c); + struct i2c_adapter *tmp = i2c_adap_p; + int max = ll_entry_count(struct i2c_adapter, i2c); + int i; + unsigned long addr; + + if (gd->reloc_off == 0) + return; + + for (i = 0; i < max; i++) { + /* adapter itself */ + addr = (unsigned long)i2c_adap_p; + addr += gd->reloc_off; + i2c_adap_p = (struct i2c_adapter *)addr; + /* i2c_init() */ + addr = (unsigned long)i2c_adap_p->init; + addr += gd->reloc_off; + i2c_adap_p->init = (void (*)(int, int))addr; + /* i2c_probe() */ + addr = (unsigned long)i2c_adap_p->probe; + addr += gd->reloc_off; + i2c_adap_p->probe = (int (*)(uint8_t))addr; + /* i2c_read() */ + addr = (unsigned long)i2c_adap_p->read; + addr += gd->reloc_off; + i2c_adap_p->read = (int (*)(uint8_t, uint, int, uint8_t *, + int))addr; + /* i2c_write() */ + addr = (unsigned long)i2c_adap_p->write; + addr += gd->reloc_off; + i2c_adap_p->write = (int (*)(uint8_t, uint, int, uint8_t *, + int))addr; + /* i2c_set_bus_speed() */ + addr = (unsigned long)i2c_adap_p->set_bus_speed; + addr += gd->reloc_off; + i2c_adap_p->set_bus_speed = (uint (*)(uint))addr; + /* name */ + addr = (unsigned long)i2c_adap_p->name; + addr += gd->reloc_off; + i2c_adap_p->name = (char *)addr; + tmp++; + i2c_adap_p = tmp; + } +#endif +} + +#ifndef CONFIG_SYS_I2C_DIRECT_BUS +/* + * i2c_mux_set() + * ------------- + * + * This turns on the given channel on I2C multiplexer chip connected to + * a given I2C adapter directly or via other multiplexers. In the latter + * case the entire multiplexer chain must be initialized first starting + * with the one connected directly to the adapter. When disabling a chain + * muxes must be programmed in reverse order, starting with the one + * farthest from the adapter. + * + * mux_id is the multiplexer chip type from defined in i2c.h. So far only + * NXP (Philips) PCA954x multiplexers are supported. Switches are NOT + * supported (anybody uses them?) + */ + +static int i2c_mux_set(struct i2c_adapter *adap, int mux_id, int chip, + int channel) +{ + uint8_t buf; + int ret; + + /* channel < 0 - turn off the mux */ + if (channel < 0) { + buf = 0; + ret = adap->write(adap, chip, 0, 0, &buf, 1); + if (ret) + printf("%s: Could not turn off the mux.\n", __func__); + return ret; + } + + switch (mux_id) { + case I2C_MUX_PCA9540_ID: + case I2C_MUX_PCA9542_ID: + if (channel > 1) + return -1; + buf = (uint8_t)((channel & 0x01) | (1 << 2)); + break; + case I2C_MUX_PCA9544_ID: + if (channel > 3) + return -1; + buf = (uint8_t)((channel & 0x03) | (1 << 2)); + break; + case I2C_MUX_PCA9547_ID: + if (channel > 7) + return -1; + buf = (uint8_t)((channel & 0x07) | (1 << 3)); + break; + default: + printf("%s: wrong mux id: %d\n", __func__, mux_id); + return -1; + } + + ret = adap->write(adap, chip, 0, 0, &buf, 1); + if (ret) + printf("%s: could not set mux: id: %d chip: %x channel: %d\n", + __func__, mux_id, chip, channel); + return ret; +} + +static int i2c_mux_set_all(void) +{ + struct i2c_bus_hose *i2c_bus_tmp = &i2c_bus[I2C_BUS]; + int i; + + /* Connect requested bus if behind muxes */ + if (i2c_bus_tmp->next_hop[0].chip != 0) { + /* Set all muxes along the path to that bus */ + for (i = 0; i < CONFIG_SYS_I2C_MAX_HOPS; i++) { + int ret; + + if (i2c_bus_tmp->next_hop[i].chip == 0) + break; + + ret = i2c_mux_set(I2C_ADAP, + i2c_bus_tmp->next_hop[i].mux.id, + i2c_bus_tmp->next_hop[i].chip, + i2c_bus_tmp->next_hop[i].channel); + if (ret != 0) + return ret; + } + } + return 0; +} + +static int i2c_mux_disconnet_all(void) +{ + struct i2c_bus_hose *i2c_bus_tmp = &i2c_bus[I2C_BUS]; + int i; + uint8_t buf; + + if (I2C_ADAP->init_done == 0) + return 0; + + /* Disconnect current bus (turn off muxes if any) */ + if ((i2c_bus_tmp->next_hop[0].chip != 0) && + (I2C_ADAP->init_done != 0)) { + i = CONFIG_SYS_I2C_MAX_HOPS; + do { + uint8_t chip; + int ret; + + chip = i2c_bus_tmp->next_hop[--i].chip; + if (chip == 0) + continue; + + ret = I2C_ADAP->write(I2C_ADAP, chip, 0, 0, &buf, 1); + if (ret != 0) { + printf("i2c: mux diconnect error\n"); + return ret; + } + } while (i > 0); + } + + return 0; +} +#endif + +/* + * i2c_init_bus(): + * --------------- + * + * Initializes one bus. Will initialize the parent adapter. No current bus + * changes, no mux (if any) setup. + */ +static void i2c_init_bus(unsigned int bus_no, int speed, int slaveaddr) +{ + if (bus_no >= CONFIG_SYS_NUM_I2C_BUSES) + return; + + I2C_ADAP->init(I2C_ADAP, speed, slaveaddr); + + if (gd->flags & GD_FLG_RELOC) { + I2C_ADAP->init_done = 1; + I2C_ADAP->speed = speed; + I2C_ADAP->slaveaddr = slaveaddr; + } +} + +/* implement possible board specific board init */ +static void __def_i2c_init_board(void) +{ +} +void i2c_init_board(void) + __attribute__((weak, alias("__def_i2c_init_board"))); + +/* + * i2c_init_all(): + * + * not longer needed, will deleted. Actual init the SPD_BUS + * for compatibility. + * i2c_adap[] must be initialized beforehead with function pointers and + * data, including speed and slaveaddr. + */ +void i2c_init_all(void) +{ + i2c_init_board(); + i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); + return; +} + +/* + * i2c_get_bus_num(): + * ------------------ + * + * Returns index of currently active I2C bus. Zero-based. + */ +unsigned int i2c_get_bus_num(void) +{ + return gd->cur_i2c_bus; +} + +/* + * i2c_set_bus_num(): + * ------------------ + * + * Change the active I2C bus. Subsequent read/write calls will + * go to this one. Sets all of the muxes in a proper condition + * if that bus is behind muxes. + * If previously selected bus is behind the muxes turns off all the + * muxes along the path to that bus. + * + * bus - bus index, zero based + * + * Returns: 0 on success, not 0 on failure + */ +int i2c_set_bus_num(unsigned int bus) +{ + int max = ll_entry_count(struct i2c_adapter, i2c); + + if (I2C_ADAPTER(bus) >= max) { + printf("Error, wrong i2c adapter %d max %d possible\n", + I2C_ADAPTER(bus), max); + return -2; + } +#ifndef CONFIG_SYS_I2C_DIRECT_BUS + if (bus >= CONFIG_SYS_NUM_I2C_BUSES) + return -1; +#endif + + if ((bus == I2C_BUS) && (I2C_ADAP->init_done > 0)) + return 0; + +#ifndef CONFIG_SYS_I2C_DIRECT_BUS + i2c_mux_disconnet_all(); +#endif + + gd->cur_i2c_bus = bus; + if (I2C_ADAP->init_done == 0) + i2c_init_bus(bus, I2C_ADAP->speed, I2C_ADAP->slaveaddr); + +#ifndef CONFIG_SYS_I2C_DIRECT_BUS + i2c_mux_set_all(); +#endif + return 0; +} + +/* + * Probe the given I2C chip address. Returns 0 if a chip responded, + * not 0 on failure. + */ +int i2c_probe(uint8_t chip) +{ + return I2C_ADAP->probe(I2C_ADAP, chip); +} + +/* + * Read/Write interface: + * chip: I2C chip address, range 0..127 + * addr: Memory (register) address within the chip + * alen: Number of bytes to use for addr (typically 1, 2 for larger + * memories, 0 for register type devices with only one + * register) + * buffer: Where to read/write the data + * len: How many bytes to read/write + * + * Returns: 0 on success, not 0 on failure + */ +int i2c_read(uint8_t chip, unsigned int addr, int alen, + uint8_t *buffer, int len) +{ + return I2C_ADAP->read(I2C_ADAP, chip, addr, alen, buffer, len); +} + +int i2c_write(uint8_t chip, unsigned int addr, int alen, + uint8_t *buffer, int len) +{ + return I2C_ADAP->write(I2C_ADAP, chip, addr, alen, buffer, len); +} + +unsigned int i2c_set_bus_speed(unsigned int speed) +{ + unsigned int ret; + + if (I2C_ADAP->set_bus_speed == NULL) + return 0; + ret = I2C_ADAP->set_bus_speed(I2C_ADAP, speed); + if (gd->flags & GD_FLG_RELOC) + I2C_ADAP->speed = ret; + + return ret; +} + +unsigned int i2c_get_bus_speed(void) +{ + struct i2c_adapter *cur = I2C_ADAP; + return cur->speed; +} + +uint8_t i2c_reg_read(uint8_t addr, uint8_t reg) +{ + uint8_t buf; + +#ifdef CONFIG_8xx + /* MPC8xx needs this. Maybe one day we can get rid of it. */ + /* maybe it is now the time for it ... */ + i2c_set_bus_num(i2c_get_bus_num()); +#endif + i2c_read(addr, reg, 1, &buf, 1); + +#ifdef DEBUG + printf("%s: bus=%d addr=0x%02x, reg=0x%02x, val=0x%02x\n", + __func__, i2c_get_bus_num(), addr, reg, buf); +#endif + + return buf; +} + +void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val) +{ +#ifdef CONFIG_8xx + /* MPC8xx needs this. Maybe one day we can get rid of it. */ + /* maybe it is now the time for it ... */ + i2c_set_bus_num(i2c_get_bus_num()); +#endif + +#ifdef DEBUG + printf("%s: bus=%d addr=0x%02x, reg=0x%02x, val=0x%02x\n", + __func__, i2c_get_bus_num(), addr, reg, val); +#endif + + i2c_write(addr, reg, 1, &val, 1); +} + +void __i2c_init(int speed, int slaveaddr) +{ + i2c_init_bus(i2c_get_bus_num(), speed, slaveaddr); +} +void i2c_init(int speed, int slaveaddr) + __attribute__((weak, alias("__i2c_init"))); diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c index 3eadbac0cd..06ba4e39f1 100644 --- a/drivers/i2c/mxc_i2c.c +++ b/drivers/i2c/mxc_i2c.c @@ -22,6 +22,15 @@ #include #include +#ifdef I2C_QUIRK_REG +struct mxc_i2c_regs { + uint8_t iadr; + uint8_t ifdr; + uint8_t i2cr; + uint8_t i2sr; + uint8_t i2dr; +}; +#else struct mxc_i2c_regs { uint32_t iadr; uint32_t ifdr; @@ -29,8 +38,8 @@ struct mxc_i2c_regs { uint32_t i2sr; uint32_t i2dr; }; +#endif -#define I2CR_IEN (1 << 7) #define I2CR_IIEN (1 << 6) #define I2CR_MSTA (1 << 5) #define I2CR_MTX (1 << 4) @@ -43,10 +52,39 @@ struct mxc_i2c_regs { #define I2SR_IIF (1 << 1) #define I2SR_RX_NO_AK (1 << 0) +#ifdef I2C_QUIRK_REG +#define I2CR_IEN (0 << 7) +#define I2CR_IDIS (1 << 7) +#define I2SR_IIF_CLEAR (1 << 1) +#else +#define I2CR_IEN (1 << 7) +#define I2CR_IDIS (0 << 7) +#define I2SR_IIF_CLEAR (0 << 1) +#endif + #if defined(CONFIG_HARD_I2C) && !defined(CONFIG_SYS_I2C_BASE) #error "define CONFIG_SYS_I2C_BASE to use the mxc_i2c driver" #endif +#ifdef I2C_QUIRK_REG +static u16 i2c_clk_div[60][2] = { + { 20, 0x00 }, { 22, 0x01 }, { 24, 0x02 }, { 26, 0x03 }, + { 28, 0x04 }, { 30, 0x05 }, { 32, 0x09 }, { 34, 0x06 }, + { 36, 0x0A }, { 40, 0x07 }, { 44, 0x0C }, { 48, 0x0D }, + { 52, 0x43 }, { 56, 0x0E }, { 60, 0x45 }, { 64, 0x12 }, + { 68, 0x0F }, { 72, 0x13 }, { 80, 0x14 }, { 88, 0x15 }, + { 96, 0x19 }, { 104, 0x16 }, { 112, 0x1A }, { 128, 0x17 }, + { 136, 0x4F }, { 144, 0x1C }, { 160, 0x1D }, { 176, 0x55 }, + { 192, 0x1E }, { 208, 0x56 }, { 224, 0x22 }, { 228, 0x24 }, + { 240, 0x1F }, { 256, 0x23 }, { 288, 0x5C }, { 320, 0x25 }, + { 384, 0x26 }, { 448, 0x2A }, { 480, 0x27 }, { 512, 0x2B }, + { 576, 0x2C }, { 640, 0x2D }, { 768, 0x31 }, { 896, 0x32 }, + { 960, 0x2F }, { 1024, 0x33 }, { 1152, 0x34 }, { 1280, 0x35 }, + { 1536, 0x36 }, { 1792, 0x3A }, { 1920, 0x37 }, { 2048, 0x3B }, + { 2304, 0x3C }, { 2560, 0x3D }, { 3072, 0x3E }, { 3584, 0x7A }, + { 3840, 0x3F }, { 4096, 0x7B }, { 5120, 0x7D }, { 6144, 0x7E }, +}; +#else static u16 i2c_clk_div[50][2] = { { 22, 0x20 }, { 24, 0x21 }, { 26, 0x22 }, { 28, 0x23 }, { 30, 0x00 }, { 32, 0x24 }, { 36, 0x25 }, { 40, 0x26 }, @@ -62,6 +100,7 @@ static u16 i2c_clk_div[50][2] = { { 1920, 0x1B }, { 2048, 0x3F }, { 2304, 0x1C }, { 2560, 0x1D }, { 3072, 0x1E }, { 3840, 0x1F } }; +#endif /* * Calculate and set proper clock divider @@ -109,7 +148,7 @@ static int bus_i2c_set_bus_speed(void *base, int speed) writeb(idx, &i2c_regs->ifdr); /* Reset module */ - writeb(0, &i2c_regs->i2cr); + writeb(I2CR_IDIS, &i2c_regs->i2cr); writeb(0, &i2c_regs->i2sr); return 0; } @@ -141,7 +180,11 @@ static int wait_for_sr_state(struct mxc_i2c_regs *i2c_regs, unsigned state) for (;;) { sr = readb(&i2c_regs->i2sr); if (sr & I2SR_IAL) { +#ifdef I2C_QUIRK_REG + writeb(sr | I2SR_IAL, &i2c_regs->i2sr); +#else writeb(sr & ~I2SR_IAL, &i2c_regs->i2sr); +#endif printf("%s: Arbitration lost sr=%x cr=%x state=%x\n", __func__, sr, readb(&i2c_regs->i2cr), state); return -ERESTART; @@ -162,7 +205,7 @@ static int tx_byte(struct mxc_i2c_regs *i2c_regs, u8 byte) { int ret; - writeb(0, &i2c_regs->i2sr); + writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); writeb(byte, &i2c_regs->i2dr); ret = wait_for_sr_state(i2c_regs, ST_IIF); if (ret < 0) @@ -198,14 +241,18 @@ static int i2c_init_transfer_(struct mxc_i2c_regs *i2c_regs, int ret; /* Enable I2C controller */ +#ifdef I2C_QUIRK_REG + if (readb(&i2c_regs->i2cr) & I2CR_IDIS) { +#else if (!(readb(&i2c_regs->i2cr) & I2CR_IEN)) { +#endif writeb(I2CR_IEN, &i2c_regs->i2cr); /* Wait for controller to be stable */ udelay(50); } if (readb(&i2c_regs->iadr) == (chip << 1)) writeb((chip << 1) ^ 2, &i2c_regs->iadr); - writeb(0, &i2c_regs->i2sr); + writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); ret = wait_for_sr_state(i2c_regs, ST_BUS_IDLE); if (ret < 0) return ret; @@ -253,7 +300,8 @@ static int i2c_init_transfer(struct mxc_i2c_regs *i2c_regs, printf("%s: failed for chip 0x%x retry=%d\n", __func__, chip, retry); if (ret != -ERESTART) - writeb(0, &i2c_regs->i2cr); /* Disable controller */ + /* Disable controller */ + writeb(I2CR_IDIS, &i2c_regs->i2cr); udelay(100); if (i2c_idle_bus(i2c_regs) < 0) break; @@ -293,7 +341,7 @@ int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf, if (len == 1) temp |= I2CR_TX_NO_AK; writeb(temp, &i2c_regs->i2cr); - writeb(0, &i2c_regs->i2sr); + writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); readb(&i2c_regs->i2dr); /* dummy read to clear ICF */ /* read data */ @@ -315,7 +363,7 @@ int bus_i2c_read(void *base, uchar chip, uint addr, int alen, uchar *buf, temp |= I2CR_TX_NO_AK; writeb(temp, &i2c_regs->i2cr); } - writeb(0, &i2c_regs->i2sr); + writeb(I2SR_IIF_CLEAR, &i2c_regs->i2sr); buf[i] = readb(&i2c_regs->i2dr); } i2c_imx_stop(i2c_regs); diff --git a/drivers/i2c/ppc4xx_i2c.c b/drivers/i2c/ppc4xx_i2c.c index 52929ebc4e..e7a15ba644 100644 --- a/drivers/i2c/ppc4xx_i2c.c +++ b/drivers/i2c/ppc4xx_i2c.c @@ -16,27 +16,29 @@ #include #include -#ifdef CONFIG_HARD_I2C - DECLARE_GLOBAL_DATA_PTR; -#if defined(CONFIG_I2C_MULTI_BUS) -/* - * Initialize the bus pointer to whatever one the SPD EEPROM is on. - * Default is bus 0. This is necessary because the DDR initialization - * runs from ROM, and we can't switch buses because we can't modify - * the global variables. - */ -#ifndef CONFIG_SYS_SPD_BUS_NUM -#define CONFIG_SYS_SPD_BUS_NUM 0 -#endif -static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = - CONFIG_SYS_SPD_BUS_NUM; -#endif /* CONFIG_I2C_MULTI_BUS */ - -static void _i2c_bus_reset(void) +static inline struct ppc4xx_i2c *ppc4xx_get_i2c(int hwadapnr) { - struct ppc4xx_i2c *i2c = (struct ppc4xx_i2c *)I2C_BASE_ADDR; + unsigned long base; + +#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ + defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT) + base = CONFIG_SYS_PERIPHERAL_BASE + 0x00000700 + (hwadapnr * 0x100); +#elif defined(CONFIG_440) || defined(CONFIG_405EX) +/* all remaining 440 variants */ + base = CONFIG_SYS_PERIPHERAL_BASE + 0x00000400 + (hwadapnr * 0x100); +#else +/* all 405 variants */ + base = 0xEF600500 + (hwadapnr * 0x100); +#endif + return (struct ppc4xx_i2c *)base; +} + +static void _i2c_bus_reset(struct i2c_adapter *adap) +{ + struct ppc4xx_i2c *i2c = ppc4xx_get_i2c(adap->hwadapnr); int i; u8 dc; @@ -75,11 +77,10 @@ static void _i2c_bus_reset(void) out_8(&i2c->xtcntlss, 0); } -void i2c_init(int speed, int slaveaddr) +static void ppc4xx_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) { - struct ppc4xx_i2c *i2c; + struct ppc4xx_i2c *i2c = ppc4xx_get_i2c(adap->hwadapnr); int val, divisor; - int bus; #ifdef CONFIG_SYS_I2C_INIT_BOARD /* @@ -90,67 +91,57 @@ void i2c_init(int speed, int slaveaddr) i2c_init_board(); #endif - for (bus = 0; bus < CONFIG_SYS_MAX_I2C_BUS; bus++) { - I2C_SET_BUS(bus); + /* Handle possible failed I2C state */ + /* FIXME: put this into i2c_init_board()? */ + _i2c_bus_reset(adap); - /* Set i2c pointer after calling I2C_SET_BUS() */ - i2c = (struct ppc4xx_i2c *)I2C_BASE_ADDR; + /* clear lo master address */ + out_8(&i2c->lmadr, 0); - /* Handle possible failed I2C state */ - /* FIXME: put this into i2c_init_board()? */ - _i2c_bus_reset(); + /* clear hi master address */ + out_8(&i2c->hmadr, 0); - /* clear lo master address */ - out_8(&i2c->lmadr, 0); + /* clear lo slave address */ + out_8(&i2c->lsadr, 0); - /* clear hi master address */ - out_8(&i2c->hmadr, 0); + /* clear hi slave address */ + out_8(&i2c->hsadr, 0); - /* clear lo slave address */ - out_8(&i2c->lsadr, 0); + /* Clock divide Register */ + /* set divisor according to freq_opb */ + divisor = (get_OPB_freq() - 1) / 10000000; + if (divisor == 0) + divisor = 1; + out_8(&i2c->clkdiv, divisor); - /* clear hi slave address */ - out_8(&i2c->hsadr, 0); + /* no interrupts */ + out_8(&i2c->intrmsk, 0); - /* Clock divide Register */ - /* set divisor according to freq_opb */ - divisor = (get_OPB_freq() - 1) / 10000000; - if (divisor == 0) - divisor = 1; - out_8(&i2c->clkdiv, divisor); + /* clear transfer count */ + out_8(&i2c->xfrcnt, 0); - /* no interrupts */ - out_8(&i2c->intrmsk, 0); + /* clear extended control & stat */ + /* write 1 in SRC SRS SWC SWS to clear these fields */ + out_8(&i2c->xtcntlss, 0xF0); - /* clear transfer count */ - out_8(&i2c->xfrcnt, 0); + /* Mode Control Register + Flush Slave/Master data buffer */ + out_8(&i2c->mdcntl, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB); - /* clear extended control & stat */ - /* write 1 in SRC SRS SWC SWS to clear these fields */ - out_8(&i2c->xtcntlss, 0xF0); + val = in_8(&i2c->mdcntl); - /* Mode Control Register - Flush Slave/Master data buffer */ - out_8(&i2c->mdcntl, IIC_MDCNTL_FSDB | IIC_MDCNTL_FMDB); + /* Ignore General Call, slave transfers are ignored, + * disable interrupts, exit unknown bus state, enable hold + * SCL 100kHz normaly or FastMode for 400kHz and above + */ - val = in_8(&i2c->mdcntl); + val |= IIC_MDCNTL_EUBS | IIC_MDCNTL_HSCL; + if (speed >= 400000) + val |= IIC_MDCNTL_FSM; + out_8(&i2c->mdcntl, val); - /* Ignore General Call, slave transfers are ignored, - * disable interrupts, exit unknown bus state, enable hold - * SCL 100kHz normaly or FastMode for 400kHz and above - */ - - val |= IIC_MDCNTL_EUBS | IIC_MDCNTL_HSCL; - if (speed >= 400000) - val |= IIC_MDCNTL_FSM; - out_8(&i2c->mdcntl, val); - - /* clear control reg */ - out_8(&i2c->cntl, 0x00); - } - - /* set to SPD bus as default bus upon powerup */ - I2C_SET_BUS(CONFIG_SYS_SPD_BUS_NUM); + /* clear control reg */ + out_8(&i2c->cntl, 0x00); } /* @@ -178,14 +169,15 @@ void i2c_init(int speed, int slaveaddr) * * It does not check XFRCNT. */ -static int i2c_transfer(unsigned char cmd_type, +static int _i2c_transfer(struct i2c_adapter *adap, + unsigned char cmd_type, unsigned char chip, unsigned char addr[], unsigned char addr_len, unsigned char data[], unsigned short data_len) { - struct ppc4xx_i2c *i2c = (struct ppc4xx_i2c *)I2C_BASE_ADDR; + struct ppc4xx_i2c *i2c = ppc4xx_get_i2c(adap->hwadapnr); u8 *ptr; int reading; int tran, cnt; @@ -329,7 +321,7 @@ static int i2c_transfer(unsigned char cmd_type, return result; } -int i2c_probe(uchar chip) +static int ppc4xx_i2c_probe(struct i2c_adapter *adap, uchar chip) { uchar buf[1]; @@ -340,11 +332,11 @@ int i2c_probe(uchar chip) * address was ed (i.e. there was a chip at that address which * drove the data line low). */ - return (i2c_transfer(1, chip << 1, 0, 0, buf, 1) != 0); + return (_i2c_transfer(adap, 1, chip << 1, 0, 0, buf, 1) != 0); } -static int ppc4xx_i2c_transfer(uchar chip, uint addr, int alen, uchar *buffer, - int len, int read) +static int ppc4xx_i2c_transfer(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len, int read) { uchar xaddr[4]; int ret; @@ -378,43 +370,50 @@ static int ppc4xx_i2c_transfer(uchar chip, uint addr, int alen, uchar *buffer, chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); #endif - if ((ret = i2c_transfer(read, chip << 1, &xaddr[4 - alen], alen, - buffer, len)) != 0) { + ret = _i2c_transfer(adap, read, chip << 1, &xaddr[4 - alen], alen, + buffer, len); + if (ret) { printf("I2C %s: failed %d\n", read ? "read" : "write", ret); - return 1; } return 0; } -int i2c_read(uchar chip, uint addr, int alen, uchar * buffer, int len) +static int ppc4xx_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { - return ppc4xx_i2c_transfer(chip, addr, alen, buffer, len, 1); + return ppc4xx_i2c_transfer(adap, chip, addr, alen, buffer, len, 1); } -int i2c_write(uchar chip, uint addr, int alen, uchar * buffer, int len) +static int ppc4xx_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { - return ppc4xx_i2c_transfer(chip, addr, alen, buffer, len, 0); + return ppc4xx_i2c_transfer(adap, chip, addr, alen, buffer, len, 0); } -#if defined(CONFIG_I2C_MULTI_BUS) -/* - * Functions for multiple I2C bus handling - */ -unsigned int i2c_get_bus_num(void) +static unsigned int ppc4xx_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) { - return i2c_bus_num; -} - -int i2c_set_bus_num(unsigned int bus) -{ - if (bus >= CONFIG_SYS_MAX_I2C_BUS) + if (speed != adap->speed) return -1; - - i2c_bus_num = bus; - - return 0; + return speed; } -#endif /* CONFIG_I2C_MULTI_BUS */ -#endif /* CONFIG_HARD_I2C */ + +/* + * Register ppc4xx i2c adapters + */ +#ifdef CONFIG_SYS_I2C_PPC4XX_CH0 +U_BOOT_I2C_ADAP_COMPLETE(ppc4xx_0, ppc4xx_i2c_init, ppc4xx_i2c_probe, + ppc4xx_i2c_read, ppc4xx_i2c_write, + ppc4xx_i2c_set_bus_speed, + CONFIG_SYS_I2C_PPC4XX_SPEED_0, + CONFIG_SYS_I2C_PPC4XX_SLAVE_0, 0) +#endif +#ifdef CONFIG_SYS_I2C_PPC4XX_CH1 +U_BOOT_I2C_ADAP_COMPLETE(ppc4xx_1, ppc4xx_i2c_init, ppc4xx_i2c_probe, + ppc4xx_i2c_read, ppc4xx_i2c_write, + ppc4xx_i2c_set_bus_speed, + CONFIG_SYS_I2C_PPC4XX_SPEED_1, + CONFIG_SYS_I2C_PPC4XX_SLAVE_1, 1) +#endif diff --git a/drivers/i2c/soft_i2c.c b/drivers/i2c/soft_i2c.c index 0a1423016e..a2baec0ace 100644 --- a/drivers/i2c/soft_i2c.c +++ b/drivers/i2c/soft_i2c.c @@ -1,4 +1,8 @@ /* + * (C) Copyright 2009 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * Changes for multibus/multiadapter I2C support. + * * (C) Copyright 2001, 2002 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. * @@ -87,14 +91,30 @@ /* #define DEBUG_I2C */ -#ifdef DEBUG_I2C DECLARE_GLOBAL_DATA_PTR; + +#ifndef I2C_SOFT_DECLARATIONS +# if defined(CONFIG_MPC8260) +# define I2C_SOFT_DECLARATIONS volatile ioport_t *iop = \ + ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT); +# elif defined(CONFIG_8xx) +# define I2C_SOFT_DECLARATIONS volatile immap_t *immr = \ + (immap_t *)CONFIG_SYS_IMMR; +# else +# define I2C_SOFT_DECLARATIONS +# endif +#endif + +#if !defined(CONFIG_SYS_SOFT_I2C_SPEED) +#define CONFIG_SYS_SOFT_I2C_SPEED CONFIG_SYS_I2C_SPEED +#endif +#if !defined(CONFIG_SYS_SOFT_I2C_SLAVE) +#define CONFIG_SYS_SOFT_I2C_SLAVE CONFIG_SYS_I2C_SLAVE #endif /*----------------------------------------------------------------------- * Definitions */ - #define RETRIES 0 #define I2C_ACK 0 /* PD_SDA level to ack a byte */ @@ -109,10 +129,6 @@ DECLARE_GLOBAL_DATA_PTR; #define PRINTD(fmt,args...) #endif -#if defined(CONFIG_I2C_MULTI_BUS) -static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = 0; -#endif /* CONFIG_I2C_MULTI_BUS */ - /*----------------------------------------------------------------------- * Local functions */ @@ -251,39 +267,6 @@ static int write_byte(uchar data) return(nack); /* not a nack is an ack */ } -#if defined(CONFIG_I2C_MULTI_BUS) -/* - * Functions for multiple I2C bus handling - */ -unsigned int i2c_get_bus_num(void) -{ - return i2c_bus_num; -} - -int i2c_set_bus_num(unsigned int bus) -{ -#if defined(CONFIG_I2C_MUX) - if (bus < CONFIG_SYS_MAX_I2C_BUS) { - i2c_bus_num = bus; - } else { - int ret; - - ret = i2x_mux_select_mux(bus); - i2c_init_board(); - if (ret == 0) - i2c_bus_num = bus; - else - return ret; - } -#else - if (bus >= CONFIG_SYS_MAX_I2C_BUS) - return -1; - i2c_bus_num = bus; -#endif - return 0; -} -#endif - /*----------------------------------------------------------------------- * if ack == I2C_ACK, ACK the byte so can continue reading, else * send I2C_NOACK to end the read. @@ -314,14 +297,10 @@ static uchar read_byte(int ack) return(data); } -/*=====================================================================*/ -/* Public Functions */ -/*=====================================================================*/ - /*----------------------------------------------------------------------- * Initialization */ -void i2c_init (int speed, int slaveaddr) +static void soft_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) { #if defined(CONFIG_SYS_I2C_INIT_BOARD) /* call board specific i2c bus reset routine before accessing the */ @@ -344,7 +323,7 @@ void i2c_init (int speed, int slaveaddr) * completion of EEPROM writes since the chip stops responding until * the write completes (typically 10mSec). */ -int i2c_probe(uchar addr) +static int soft_i2c_probe(struct i2c_adapter *adap, uint8_t addr) { int rc; @@ -362,7 +341,8 @@ int i2c_probe(uchar addr) /*----------------------------------------------------------------------- * Read bytes */ -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int soft_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { int shift; PRINTD("i2c_read: chip %02X addr %02X alen %d buffer %p len %d\n", @@ -436,7 +416,8 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) /*----------------------------------------------------------------------- * Write bytes */ -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int soft_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { int shift, failures = 0; @@ -466,3 +447,32 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) send_stop(); return(failures); } + +/* + * Register soft i2c adapters + */ +U_BOOT_I2C_ADAP_COMPLETE(soft0, soft_i2c_init, soft_i2c_probe, + soft_i2c_read, soft_i2c_write, NULL, + CONFIG_SYS_I2C_SOFT_SPEED, CONFIG_SYS_I2C_SOFT_SLAVE, + 0) +#if defined(I2C_SOFT_DECLARATIONS2) +U_BOOT_I2C_ADAP_COMPLETE(soft1, soft_i2c_init, soft_i2c_probe, + soft_i2c_read, soft_i2c_write, NULL, + CONFIG_SYS_I2C_SOFT_SPEED_2, + CONFIG_SYS_I2C_SOFT_SLAVE_2, + 1) +#endif +#if defined(I2C_SOFT_DECLARATIONS3) +U_BOOT_I2C_ADAP_COMPLETE(soft2, soft_i2c_init, soft_i2c_probe, + soft_i2c_read, soft_i2c_write, NULL, + CONFIG_SYS_I2C_SOFT_SPEED_3, + CONFIG_SYS_I2C_SOFT_SLAVE_3, + 2) +#endif +#if defined(I2C_SOFT_DECLARATIONS4) +U_BOOT_I2C_ADAP_COMPLETE(soft3, soft_i2c_init, soft_i2c_probe, + soft_i2c_read, soft_i2c_write, NULL, + CONFIG_SYS_I2C_SOFT_SPEED_4, + CONFIG_SYS_I2C_SOFT_SLAVE_4, + 3) +#endif diff --git a/drivers/i2c/tegra_i2c.c b/drivers/i2c/tegra_i2c.c index e96d5d5d09..9ac3969a07 100644 --- a/drivers/i2c/tegra_i2c.c +++ b/drivers/i2c/tegra_i2c.c @@ -19,8 +19,6 @@ DECLARE_GLOBAL_DATA_PTR; -static unsigned int i2c_bus_num; - /* Information about i2c controller */ struct i2c_bus { int id; @@ -268,7 +266,8 @@ exit: return error; } -static int tegra_i2c_write_data(u32 addr, u8 *data, u32 len) +static int tegra_i2c_write_data(struct i2c_bus *bus, u32 addr, u8 *data, + u32 len) { int error; struct i2c_trans_info trans_info; @@ -279,14 +278,15 @@ static int tegra_i2c_write_data(u32 addr, u8 *data, u32 len) trans_info.num_bytes = len; trans_info.is_10bit_address = 0; - error = send_recv_packets(&i2c_controllers[i2c_bus_num], &trans_info); + error = send_recv_packets(bus, &trans_info); if (error) debug("tegra_i2c_write_data: Error (%d) !!!\n", error); return error; } -static int tegra_i2c_read_data(u32 addr, u8 *data, u32 len) +static int tegra_i2c_read_data(struct i2c_bus *bus, u32 addr, u8 *data, + u32 len) { int error; struct i2c_trans_info trans_info; @@ -297,7 +297,7 @@ static int tegra_i2c_read_data(u32 addr, u8 *data, u32 len) trans_info.num_bytes = len; trans_info.is_10bit_address = 0; - error = send_recv_packets(&i2c_controllers[i2c_bus_num], &trans_info); + error = send_recv_packets(bus, &trans_info); if (error) debug("tegra_i2c_read_data: Error (%d) !!!\n", error); @@ -308,18 +308,35 @@ static int tegra_i2c_read_data(u32 addr, u8 *data, u32 len) #error "Please enable device tree support to use this driver" #endif -unsigned int i2c_get_bus_speed(void) +/** + * Check that a bus number is valid and return a pointer to it + * + * @param bus_num Bus number to check / return + * @return pointer to bus, if valid, else NULL + */ +static struct i2c_bus *tegra_i2c_get_bus(struct i2c_adapter *adap) { - return i2c_controllers[i2c_bus_num].speed; + struct i2c_bus *bus; + + bus = &i2c_controllers[adap->hwadapnr]; + if (!bus->inited) { + debug("%s: Bus %u not available\n", __func__, adap->hwadapnr); + return NULL; + } + + return bus; } -int i2c_set_bus_speed(unsigned int speed) +static unsigned int tegra_i2c_set_bus_speed(struct i2c_adapter *adap, + unsigned int speed) { - struct i2c_bus *i2c_bus; + struct i2c_bus *bus; - i2c_bus = &i2c_controllers[i2c_bus_num]; - i2c_bus->speed = speed; - i2c_init_controller(i2c_bus); + bus = tegra_i2c_get_bus(adap); + if (!bus) + return 0; + bus->speed = speed; + i2c_init_controller(bus); return 0; } @@ -434,7 +451,7 @@ void i2c_init_board(void) return; } -void i2c_init(int speed, int slaveaddr) +static void tegra_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) { /* This will override the speed selected in the fdt for that port */ debug("i2c_init(speed=%u, slaveaddr=0x%x)\n", speed, slaveaddr); @@ -442,7 +459,7 @@ void i2c_init(int speed, int slaveaddr) } /* i2c write version without the register address */ -int i2c_write_data(uchar chip, uchar *buffer, int len) +int i2c_write_data(struct i2c_bus *bus, uchar chip, uchar *buffer, int len) { int rc; @@ -454,7 +471,7 @@ int i2c_write_data(uchar chip, uchar *buffer, int len) debug("\n"); /* Shift 7-bit address over for lower-level i2c functions */ - rc = tegra_i2c_write_data(chip << 1, buffer, len); + rc = tegra_i2c_write_data(bus, chip << 1, buffer, len); if (rc) debug("i2c_write_data(): rc=%d\n", rc); @@ -462,13 +479,13 @@ int i2c_write_data(uchar chip, uchar *buffer, int len) } /* i2c read version without the register address */ -int i2c_read_data(uchar chip, uchar *buffer, int len) +int i2c_read_data(struct i2c_bus *bus, uchar chip, uchar *buffer, int len) { int rc; debug("inside i2c_read_data():\n"); /* Shift 7-bit address over for lower-level i2c functions */ - rc = tegra_i2c_read_data(chip << 1, buffer, len); + rc = tegra_i2c_read_data(bus, chip << 1, buffer, len); if (rc) { debug("i2c_read_data(): rc=%d\n", rc); return rc; @@ -484,14 +501,18 @@ int i2c_read_data(uchar chip, uchar *buffer, int len) } /* Probe to see if a chip is present. */ -int i2c_probe(uchar chip) +static int tegra_i2c_probe(struct i2c_adapter *adap, uchar chip) { + struct i2c_bus *bus; int rc; uchar reg; debug("i2c_probe: addr=0x%x\n", chip); + bus = tegra_i2c_get_bus(adap); + if (!bus) + return 1; reg = 0; - rc = i2c_write_data(chip, ®, 1); + rc = i2c_write_data(bus, chip, ®, 1); if (rc) { debug("Error probing 0x%x.\n", chip); return 1; @@ -506,13 +527,18 @@ static int i2c_addr_ok(const uint addr, const int alen) } /* Read bytes */ -int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int tegra_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { + struct i2c_bus *bus; uint offset; int i; debug("i2c_read: chip=0x%x, addr=0x%x, len=0x%x\n", chip, addr, len); + bus = tegra_i2c_get_bus(adap); + if (!bus) + return 1; if (!i2c_addr_ok(addr, alen)) { debug("i2c_read: Bad address %x.%d.\n", addr, alen); return 1; @@ -524,13 +550,13 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) data[alen - i - 1] = (addr + offset) >> (8 * i); } - if (i2c_write_data(chip, data, alen)) { + if (i2c_write_data(bus, chip, data, alen)) { debug("i2c_read: error sending (0x%x)\n", addr); return 1; } } - if (i2c_read_data(chip, buffer + offset, 1)) { + if (i2c_read_data(bus, chip, buffer + offset, 1)) { debug("i2c_read: error reading (0x%x)\n", addr); return 1; } @@ -540,13 +566,18 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len) } /* Write bytes */ -int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) +static int tegra_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, + int alen, uchar *buffer, int len) { + struct i2c_bus *bus; uint offset; int i; debug("i2c_write: chip=0x%x, addr=0x%x, len=0x%x\n", chip, addr, len); + bus = tegra_i2c_get_bus(adap); + if (!bus) + return 1; if (!i2c_addr_ok(addr, alen)) { debug("i2c_write: Bad address %x.%d.\n", addr, alen); return 1; @@ -556,7 +587,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) for (i = 0; i < alen; i++) data[alen - i - 1] = (addr + offset) >> (8 * i); data[alen] = buffer[offset]; - if (i2c_write_data(chip, data, alen + 1)) { + if (i2c_write_data(bus, chip, data, alen + 1)) { debug("i2c_write: error sending (0x%x)\n", addr); return 1; } @@ -565,30 +596,11 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) return 0; } -#if defined(CONFIG_I2C_MULTI_BUS) -/* - * Functions for multiple I2C bus handling - */ -unsigned int i2c_get_bus_num(void) -{ - return i2c_bus_num; -} - -int i2c_set_bus_num(unsigned int bus) -{ - if (bus >= TEGRA_I2C_NUM_CONTROLLERS || !i2c_controllers[bus].inited) - return -1; - i2c_bus_num = bus; - - return 0; -} -#endif - int tegra_i2c_get_dvc_bus_num(void) { int i; - for (i = 0; i < CONFIG_SYS_MAX_I2C_BUS; i++) { + for (i = 0; i < TEGRA_I2C_NUM_CONTROLLERS; i++) { struct i2c_bus *bus = &i2c_controllers[i]; if (bus->inited && bus->is_dvc) @@ -597,3 +609,19 @@ int tegra_i2c_get_dvc_bus_num(void) return -1; } + +/* + * Register soft i2c adapters + */ +U_BOOT_I2C_ADAP_COMPLETE(tegra0, tegra_i2c_init, tegra_i2c_probe, + tegra_i2c_read, tegra_i2c_write, + tegra_i2c_set_bus_speed, 100000, 0, 0) +U_BOOT_I2C_ADAP_COMPLETE(tegra1, tegra_i2c_init, tegra_i2c_probe, + tegra_i2c_read, tegra_i2c_write, + tegra_i2c_set_bus_speed, 100000, 0, 1) +U_BOOT_I2C_ADAP_COMPLETE(tegra2, tegra_i2c_init, tegra_i2c_probe, + tegra_i2c_read, tegra_i2c_write, + tegra_i2c_set_bus_speed, 100000, 0, 2) +U_BOOT_I2C_ADAP_COMPLETE(tegra3, tegra_i2c_init, tegra_i2c_probe, + tegra_i2c_read, tegra_i2c_write, + tegra_i2c_set_bus_speed, 100000, 0, 3) diff --git a/include/asm-generic/global_data.h b/include/asm-generic/global_data.h index 77260a8d20..77e06fb4fe 100644 --- a/include/asm-generic/global_data.h +++ b/include/asm-generic/global_data.h @@ -68,6 +68,9 @@ typedef struct global_data { char env_buf[32]; /* buffer for getenv() before reloc. */ #ifdef CONFIG_TRACE void *trace_buff; /* The trace buffer */ +#endif +#if defined(CONFIG_SYS_I2C) + int cur_i2c_bus; /* current used i2c bus */ #endif struct arch_global_data arch; /* architecture-specific data */ } gd_t; diff --git a/include/configs/A3000.h b/include/configs/A3000.h index 6c204db0ab..90a21768e9 100644 --- a/include/configs/A3000.h +++ b/include/configs/A3000.h @@ -70,8 +70,8 @@ * PCI stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_HARD_I2C 1 /* To enable I2C support */ +#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F diff --git a/include/configs/APC405.h b/include/configs/APC405.h index 82245c4586..37bcac32c7 100644 --- a/include/configs/APC405.h +++ b/include/configs/APC405.h @@ -290,10 +290,11 @@ /* * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h index 233bc68ab8..54de966741 100644 --- a/include/configs/ASH405.h +++ b/include/configs/ASH405.h @@ -231,10 +231,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h index ad1bd7eb77..09043435b4 100644 --- a/include/configs/B4860QDS.h +++ b/include/configs/B4860QDS.h @@ -443,14 +443,14 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed in Hz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x118000 -#define CONFIG_SYS_I2C2_OFFSET 0x119000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ +#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 /* * RTC configuration diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h index b6a879058e..948394eddd 100644 --- a/include/configs/BSC9131RDB.h +++ b/include/configs/BSC9131RDB.h @@ -259,13 +259,11 @@ extern unsigned long get_sdram_size(void); #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 /* I2C EEPROM */ #define CONFIG_CMD_EEPROM diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h index e8e2c6f24d..1ab6891585 100644 --- a/include/configs/BSC9132QDS.h +++ b/include/configs/BSC9132QDS.h @@ -435,15 +435,14 @@ combinations. this should be removed later #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400800 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400800 /* I2C speed and slave address*/ +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400800 /* I2C speed and slave address*/ +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C EEPROM */ #define CONFIG_ID_EEPROM diff --git a/include/configs/CANBT.h b/include/configs/CANBT.h index 66e3790782..40471b78a1 100644 --- a/include/configs/CANBT.h +++ b/include/configs/CANBT.h @@ -164,13 +164,14 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC08) for environment */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h index d6fca13a9f..3906863f05 100644 --- a/include/configs/CATcenter.h +++ b/include/configs/CATcenter.h @@ -389,10 +389,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h index e7609a75eb..323eac3fb4 100644 --- a/include/configs/CMS700.h +++ b/include/configs/CMS700.h @@ -210,10 +210,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/CPCI2DP.h b/include/configs/CPCI2DP.h index 0f98274418..bd9fd6ee7b 100644 --- a/include/configs/CPCI2DP.h +++ b/include/configs/CPCI2DP.h @@ -195,10 +195,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h index c6fa22a639..94ef16e06c 100644 --- a/include/configs/CPCI405.h +++ b/include/configs/CPCI405.h @@ -244,10 +244,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC08) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index f43660ebe5..8383c19359 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -271,10 +271,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index dbf0662b54..ec9f5aec4a 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -247,10 +247,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC32) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h index e5a962ae23..ba926abdc0 100644 --- a/include/configs/CPCI405DT.h +++ b/include/configs/CPCI405DT.h @@ -266,10 +266,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/CPCIISER4.h b/include/configs/CPCIISER4.h index 2a89efe190..dc4df29455 100644 --- a/include/configs/CPCIISER4.h +++ b/include/configs/CPCIISER4.h @@ -180,10 +180,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC08) for environment */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/CPU86.h b/include/configs/CPU86.h index b11262690f..a85a418fb1 100644 --- a/include/configs/CPU86.h +++ b/include/configs/CPU86.h @@ -113,10 +113,11 @@ /*----------------------------------------------------------------------- * I2C/EEPROM/RTC configuration */ -#define CONFIG_SOFT_I2C /* Software I2C support enabled */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -# define CONFIG_SYS_I2C_SPEED 50000 -# define CONFIG_SYS_I2C_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ diff --git a/include/configs/CPU87.h b/include/configs/CPU87.h index bbd0022f74..7bbcb77af7 100644 --- a/include/configs/CPU87.h +++ b/include/configs/CPU87.h @@ -117,10 +117,11 @@ /*----------------------------------------------------------------------- * I2C/EEPROM/RTC configuration */ -#define CONFIG_SOFT_I2C /* Software I2C support enabled */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -# define CONFIG_SYS_I2C_SPEED 50000 -# define CONFIG_SYS_I2C_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ diff --git a/include/configs/CRAYL1.h b/include/configs/CRAYL1.h index a19b431882..fa3efabea4 100644 --- a/include/configs/CRAYL1.h +++ b/include/configs/CRAYL1.h @@ -60,11 +60,12 @@ #define CONFIG_SERVERIP 10.0.0.1 #define CONFIG_ETHADDR 00:40:a6:80:14:5 */ -#define CONFIG_HARD_I2C 1 /* hardware support for i2c */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 #define CONFIG_SDRAM_BANK0 1 -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_IDENT_STRING "Cray L1" diff --git a/include/configs/DP405.h b/include/configs/DP405.h index 9254796cfb..872a2b4408 100644 --- a/include/configs/DP405.h +++ b/include/configs/DP405.h @@ -162,10 +162,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/DU405.h b/include/configs/DU405.h index b6825d5ad2..5b9e0d2f41 100644 --- a/include/configs/DU405.h +++ b/include/configs/DU405.h @@ -181,10 +181,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC08) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/DU440.h b/include/configs/DU440.h index 9b338535d9..08271132dc 100644 --- a/include/configs/DU440.h +++ b/include/configs/DU440.h @@ -157,19 +157,20 @@ /* * I2C */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_I2C_MULTI_BUS 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_PPC4XX_CH1 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F #define CONFIG_SYS_SPD_BUS_NUM 0 #define IIC1_MCP3021_ADDR 0x4d #define IIC1_USB2507_ADDR 0x2c -#ifdef CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_NOPROBES {{1, IIC1_USB2507_ADDR}} -#endif +#define CONFIG_SYS_I2C_NOPROBES { {1, IIC1_USB2507_ADDR} } + #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 diff --git a/include/configs/G2000.h b/include/configs/G2000.h index 1edd6df7c3..5a74abcd41 100644 --- a/include/configs/G2000.h +++ b/include/configs/G2000.h @@ -282,10 +282,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */ /* CAT24WC08/16... */ diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h index 2962c915aa..06c0e50c96 100644 --- a/include/configs/GEN860T.h +++ b/include/configs/GEN860T.h @@ -142,26 +142,33 @@ /* * Enable I2C and select the hardware/software driver */ -#define CONFIG_HARD_I2C 1 /* CPM based I2C */ -#undef CONFIG_SOFT_I2C /* Bit-banged I2C */ +#define CONFIG_HARD_I2C 1 /* CPM based I2C */ +#undef CONFIG_SYS_I2C_SOFT /* Bit-banged I2C */ #ifdef CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 /* clock speed in Hz */ -#define CONFIG_SYS_I2C_SLAVE 0xFE /* I2C slave address */ +#define CONFIG_SYS_I2C_SPEED 100000 /* clock speed in Hz */ +#define CONFIG_SYS_I2C_SLAVE 0xFE /* I2C slave address */ #endif -#ifdef CONFIG_SOFT_I2C -#define PB_SCL 0x00000020 /* PB 26 */ -#define PB_SDA 0x00000010 /* PB 27 */ -#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) -#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) -#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) -#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) -#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ - else immr->im_cpm.cp_pbdat &= ~PB_SDA -#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ - else immr->im_cpm.cp_pbdat &= ~PB_SCL -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#ifdef CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if (bit) \ + immr->im_cpm.cp_pbdat |= PB_SDA; \ + else \ + immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if (bit) \ + immr->im_cpm.cp_pbdat |= PB_SCL; \ + else \ + immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ #endif /* diff --git a/include/configs/HH405.h b/include/configs/HH405.h index 943d6ddd98..d20ca77870 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -318,14 +318,15 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 #if 0 /* test-only */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #else -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 #endif -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */ #define CONFIG_SYS_EEPROM_WREN 1 diff --git a/include/configs/HIDDEN_DRAGON.h b/include/configs/HIDDEN_DRAGON.h index c1d3f10525..ddeccb0868 100644 --- a/include/configs/HIDDEN_DRAGON.h +++ b/include/configs/HIDDEN_DRAGON.h @@ -153,12 +153,15 @@ * configuration items that the driver uses to drive the port pins. */ #define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT #error "Soft I2C is not configured properly. Please review!" +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE #define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ #define I2C_ACTIVE (iop->pdir |= 0x00010000) #define I2C_TRISTATE (iop->pdir &= ~0x00010000) @@ -168,7 +171,7 @@ #define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ else iop->pdat &= ~0x00020000 #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ +#endif /* CONFIG_SYS_I2C_SOFT */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h index 30effc3d72..cf796bf2d9 100644 --- a/include/configs/HUB405.h +++ b/include/configs/HUB405.h @@ -230,10 +230,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/HWW1U1A.h b/include/configs/HWW1U1A.h index 8c217562a1..5aaa9767e9 100644 --- a/include/configs/HWW1U1A.h +++ b/include/configs/HWW1U1A.h @@ -202,16 +202,16 @@ /* -------------------------------------------------------------------- */ /* Generic FreeScale hardware I2C support */ -#define CONFIG_HARD_I2C -#define CONFIG_FSL_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } #define CONFIG_CMD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 - -/* I2C bus configuration */ -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F /* DDR2 SO-RDIMM SPD EEPROM is at I2C0-0x51 */ #define CONFIG_SYS_SPD_BUS_NUM 0 diff --git a/include/configs/ICU862.h b/include/configs/ICU862.h index 48a05d52ff..40d0d7cab9 100644 --- a/include/configs/ICU862.h +++ b/include/configs/ICU862.h @@ -90,12 +90,10 @@ #define CONFIG_DOS_PARTITION /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -# define CONFIG_SYS_I2C_SPEED 50000 -# define CONFIG_SYS_I2C_SLAVE 0xFE -# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -117,6 +115,9 @@ #define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ + /* * Command line configuration. diff --git a/include/configs/IDS8247.h b/include/configs/IDS8247.h index c7409debe1..590abc30df 100644 --- a/include/configs/IDS8247.h +++ b/include/configs/IDS8247.h @@ -57,11 +57,10 @@ #define CONFIG_MISC_INIT_R 1 /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 400000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F /* * Software (bit-bang) I2C driver configuration */ diff --git a/include/configs/IP860.h b/include/configs/IP860.h index 1247181b54..c852ca998b 100644 --- a/include/configs/IP860.h +++ b/include/configs/IP860.h @@ -46,8 +46,10 @@ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -64,9 +66,6 @@ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -# define CONFIG_SYS_I2C_SPEED 50000 -# define CONFIG_SYS_I2C_SLAVE 0xFE # define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */ # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ diff --git a/include/configs/IPHASE4539.h b/include/configs/IPHASE4539.h index bcc007c4d2..cbc8b5bbc1 100644 --- a/include/configs/IPHASE4539.h +++ b/include/configs/IPHASE4539.h @@ -94,15 +94,13 @@ * If the software driver is chosen, there are some additional * configuration items that the driver uses to drive the port pins. */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 400000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F /* * Software (bit-bang) I2C driver configuration */ -#ifdef CONFIG_SOFT_I2C #define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ #define I2C_ACTIVE (iop->pdir |= 0x00010000) #define I2C_TRISTATE (iop->pdir &= ~0x00010000) @@ -112,7 +110,6 @@ #define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ else iop->pdat &= ~0x00020000 #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ /* diff --git a/include/configs/JSE.h b/include/configs/JSE.h index c855c7f02f..6439d99bf8 100644 --- a/include/configs/JSE.h +++ b/include/configs/JSE.h @@ -194,11 +194,11 @@ #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /*----------------------------------------------------------------------- diff --git a/include/configs/KAREF.h b/include/configs/KAREF.h index d7377a8e91..2cbb6eeb9c 100644 --- a/include/configs/KAREF.h +++ b/include/configs/KAREF.h @@ -117,14 +117,15 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C hardware support */ -#undef CONFIG_SOFT_I2C /* I2C !bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed 400kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_I2C_BUS1 1 /* Include i2c bus 1 supp */ - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_PPC4XX_CH1 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 /* I2C speed 400kHz */ +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F +#define CONFIG_SYS_I2C_NOPROBES { { 0, 0x69} } /* Don't probe these addrs */ /*----------------------------------------------------------------------- * Environment diff --git a/include/configs/KUP4K.h b/include/configs/KUP4K.h index 68451baf75..ef51e35df6 100644 --- a/include/configs/KUP4K.h +++ b/include/configs/KUP4K.h @@ -90,13 +90,11 @@ /* * enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C /* * Software (bit-bang) I2C driver configuration */ @@ -112,7 +110,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ /*----------------------------------------------------------------------- * I2C Configuration diff --git a/include/configs/KUP4X.h b/include/configs/KUP4X.h index 8af1269a45..6da07e7d06 100644 --- a/include/configs/KUP4X.h +++ b/include/configs/KUP4X.h @@ -98,13 +98,13 @@ /* * enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE +#ifdef CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -#ifdef CONFIG_SOFT_I2C /* * Software (bit-bang) I2C driver configuration */ @@ -120,7 +120,7 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ +#endif /* CONFIG_SYS_I2C_SOFT */ /*----------------------------------------------------------------------- diff --git a/include/configs/M5208EVBE.h b/include/configs/M5208EVBE.h index df9ba5ea3c..fe901ce6c2 100644 --- a/include/configs/M5208EVBE.h +++ b/include/configs/M5208EVBE.h @@ -66,12 +66,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ diff --git a/include/configs/M52277EVB.h b/include/configs/M52277EVB.h index 4acac6c442..1d10f7f2a0 100644 --- a/include/configs/M52277EVB.h +++ b/include/configs/M52277EVB.h @@ -129,12 +129,11 @@ #undef CONFIG_MCFPIT /* I2c */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* DSPI and Serial Flash */ diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h index 1b80f82934..aaaaa41a15 100644 --- a/include/configs/M5235EVB.h +++ b/include/configs/M5235EVB.h @@ -83,12 +83,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_i2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_SYS_I2C_PINMUX_REG (gpio->par_qspi) #define CONFIG_SYS_I2C_PINMUX_CLR ~(GPIO_PAR_FECI2C_SCL_MASK | GPIO_PAR_FECI2C_SDA_MASK) diff --git a/include/configs/M5253DEMO.h b/include/configs/M5253DEMO.h index bf37fdf14b..83122cf59f 100644 --- a/include/configs/M5253DEMO.h +++ b/include/configs/M5253DEMO.h @@ -97,11 +97,11 @@ TABILITY or FITNESS FO04-2007 Freescale Semiconductor, Inc. #define CONFIG_HOSTNAME M5253DEMO /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00000280 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000280 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_SYS_I2C_PINMUX_REG (*(u32 *) (CONFIG_SYS_MBAR+0x19C)) #define CONFIG_SYS_I2C_PINMUX_CLR (0xFFFFE7FF) diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h index fa43231c49..a77cb24975 100644 --- a/include/configs/M5271EVB.h +++ b/include/configs/M5271EVB.h @@ -93,12 +93,11 @@ #endif /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */ diff --git a/include/configs/M5275EVB.h b/include/configs/M5275EVB.h index 2b99ee9f1c..bacee0a8fa 100644 --- a/include/configs/M5275EVB.h +++ b/include/configs/M5275EVB.h @@ -93,12 +93,11 @@ #endif /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_SYS_I2C_PINMUX_REG (gpio_reg->par_feci2c) #define CONFIG_SYS_I2C_PINMUX_CLR (0xFFF0) diff --git a/include/configs/M53017EVB.h b/include/configs/M53017EVB.h index a98ded2570..0ced196489 100644 --- a/include/configs/M53017EVB.h +++ b/include/configs/M53017EVB.h @@ -85,12 +85,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h index d5d3bc48cd..86b06f4f16 100644 --- a/include/configs/M5329EVB.h +++ b/include/configs/M5329EVB.h @@ -79,12 +79,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ diff --git a/include/configs/M5373EVB.h b/include/configs/M5373EVB.h index 8657382c8e..cca76097dc 100644 --- a/include/configs/M5373EVB.h +++ b/include/configs/M5373EVB.h @@ -79,12 +79,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR #define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h index aa95de2a67..bc264276d4 100644 --- a/include/configs/M54418TWR.h +++ b/include/configs/M54418TWR.h @@ -197,9 +197,9 @@ #undef CONFIG_MCFPIT /* I2c */ -#undef CONFIG_FSL_I2C +#undef CONFIG_SYS_FSL_I2C #undef CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SPEED 80000 #define CONFIG_SYS_I2C_SLAVE 0x7F diff --git a/include/configs/M54451EVB.h b/include/configs/M54451EVB.h index 720e888f6f..72ad8366fb 100644 --- a/include/configs/M54451EVB.h +++ b/include/configs/M54451EVB.h @@ -140,12 +140,11 @@ #undef CONFIG_MCFPIT /* I2c */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* DSPI and Serial Flash */ diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h index 03dafd5440..3dc87d6f61 100644 --- a/include/configs/M54455EVB.h +++ b/include/configs/M54455EVB.h @@ -173,12 +173,11 @@ #undef CONFIG_MCFPIT /* I2c */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSLI2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* DSPI and Serial Flash */ diff --git a/include/configs/M5475EVB.h b/include/configs/M5475EVB.h index b5bf1c7f99..dc38219c1d 100644 --- a/include/configs/M5475EVB.h +++ b/include/configs/M5475EVB.h @@ -104,12 +104,11 @@ #endif /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00008F00 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* PCI */ diff --git a/include/configs/M5485EVB.h b/include/configs/M5485EVB.h index 3924936a5a..0307f19ad2 100644 --- a/include/configs/M5485EVB.h +++ b/include/configs/M5485EVB.h @@ -101,12 +101,11 @@ #endif /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x00008F00 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00008F00 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* PCI */ diff --git a/include/configs/MERGERBOX.h b/include/configs/MERGERBOX.h index 6119159e4a..ad9c77e1c8 100644 --- a/include/configs/MERGERBOX.h +++ b/include/configs/MERGERBOX.h @@ -211,13 +211,14 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 120000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * General PCI diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h index b98a4c481e..1e50032414 100644 --- a/include/configs/METROBOX.h +++ b/include/configs/METROBOX.h @@ -179,14 +179,15 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C hardware support */ -#undef CONFIG_SOFT_I2C /* I2C !bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed 400kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_I2C_BUS1 1 /* Include i2c bus 1 supp */ - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_PPC4XX_CH1 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 /* I2C speed 400kHz */ +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F +#define CONFIG_SYS_I2C_NOPROBES { { 0, 0x69} } /* Don't probe these addrs */ /*----------------------------------------------------------------------- * Environment diff --git a/include/configs/MHPC.h b/include/configs/MHPC.h index 65efe78f33..75eef20e58 100644 --- a/include/configs/MHPC.h +++ b/include/configs/MHPC.h @@ -57,8 +57,10 @@ #undef CONFIG_UCODE_PATCH /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -75,8 +77,6 @@ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0xFE #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C04 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h index 9185e77ad1..c535dbeaae 100644 --- a/include/configs/MIP405.h +++ b/include/configs/MIP405.h @@ -82,10 +82,11 @@ * The Atmel EEPROM uses 16Bit addressing. ***************************************************************/ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 50000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 /* EEPROM 24C128/256 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h index 09961a4eb8..d315729b8b 100644 --- a/include/configs/MPC8308RDB.h +++ b/include/configs/MPC8308RDB.h @@ -334,14 +334,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * SPI on header J8 diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 6740182045..6c6ce58fb8 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -387,14 +387,15 @@ #define CONFIG_SYS_HUSH_PARSER /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * General PCI diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h index 882ae73e05..fef19d4b5f 100644 --- a/include/configs/MPC8315ERDB.h +++ b/include/configs/MPC8315ERDB.h @@ -331,13 +331,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave addr */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Board info - revision and where boot from diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index ac4c253968..d5db65df11 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -233,13 +233,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Config on-board EEPROM diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index fa8e75250a..32e05af8ab 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -313,13 +313,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Config on-board RTC diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 9ec2f71921..432db72daa 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -338,15 +338,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* SPI */ #define CONFIG_MPC8XXX_SPI diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index f9949a8000..c3a577f40a 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -74,7 +74,7 @@ #define CONFIG_PCI #define CONFIG_RTC_DS1337 -#define CONFIG_HARD_I2C +#define CONFIG_SYS_I2C #define CONFIG_TSEC_ENET /* TSEC Ethernet support */ /* @@ -82,12 +82,15 @@ */ /* I2C */ -#ifdef CONFIG_HARD_I2C +#ifdef CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 #define CONFIG_SYS_SPD_BUS_NUM 1 /* The I2C bus for SPD */ #define CONFIG_SYS_RTC_BUS_NUM 1 /* The I2C bus for RTC */ @@ -99,9 +102,6 @@ #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* I2C1, DS1339 RTC*/ #define SPD_EEPROM_ADDRESS 0x51 /* I2C1, DDR */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - /* Don't probe these addresses: */ #define CONFIG_SYS_I2C_NOPROBES { {1, CONFIG_SYS_I2C_8574_ADDR1}, \ {1, CONFIG_SYS_I2C_8574_ADDR2}, \ @@ -115,8 +115,6 @@ #define I2C_8574_PCI66 0x20 /* 0=33MHz PCI, 1=66MHz PCI */ #define I2C_8574_FLASHSIDE 0x40 /* 0=Reset vector from U4, 1=from U7*/ -#undef CONFIG_SOFT_I2C - #endif /* Compact Flash */ @@ -183,7 +181,7 @@ #define CONFIG_VERY_BIG_RAM #define CONFIG_MAX_MEM_MAPPED ((phys_size_t)256 << 20) -#ifdef CONFIG_HARD_I2C +#ifdef CONFIG_SYS_I2C #define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ #endif @@ -529,7 +527,7 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CONFIG_CMD_PCI #endif -#ifdef CONFIG_HARD_I2C +#ifdef CONFIG_SYS_I2C #define CONFIG_CMD_I2C #endif diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index dfd2a50c6d..7c4f3ef8f1 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -410,14 +410,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x52} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* * Config on-board RTC diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h index 2c194087a4..1973447a23 100644 --- a/include/configs/MPC8360ERDK.h +++ b/include/configs/MPC8360ERDK.h @@ -284,15 +284,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } /* * General PCI diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index ab61d214d3..51688a76bf 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -328,14 +328,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Config on-board RTC diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index 1529a090ed..a5fe220b14 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -354,14 +354,12 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } /* * Config on-board RTC diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h index 5349857ebb..8ff2c3a4fa 100644 --- a/include/configs/MPC8536DS.h +++ b/include/configs/MPC8536DS.h @@ -418,15 +418,15 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } /* * I2C2 EEPROM diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index c80b6b2fdb..acd37a01aa 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -244,13 +244,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* RapidIO MMU */ #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index da7a3cbb46..61775d2c28 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -267,13 +267,12 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* EEPROM */ #define CONFIG_ID_EEPROM diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index ef8bf97f62..2a5e5d4ed9 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -216,14 +216,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3100 /* * General PCI diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index 84bd3af1af..8deb241c39 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -342,13 +342,12 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* EEPROM */ #define CONFIG_ID_EEPROM diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index eb4e620d8b..1ec3797e7c 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -265,13 +265,12 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* EEPROM */ #define CONFIG_ID_EEPROM diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index d4a557b675..49f6a35332 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -238,13 +238,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* RapidIO MMU */ #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index 21ce7b9125..2d5e8c0b7b 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -250,16 +250,16 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * General PCI diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h index 7f7cd20d78..c35fd2bdbc 100644 --- a/include/configs/MPC8569MDS.h +++ b/include/configs/MPC8569MDS.h @@ -286,15 +286,15 @@ extern unsigned long get_clock_freq(void); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * I2C2 EEPROM diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index e9da736327..05d8870500 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -415,16 +415,16 @@ #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index f791e7682e..1553a746c8 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -252,13 +252,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * General PCI diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 89049d0f62..6ca6f6b807 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -282,13 +282,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * RapidIO MMU diff --git a/include/configs/MVBLM7.h b/include/configs/MVBLM7.h index bb5a4fc5e3..044a1bc2c8 100644 --- a/include/configs/MVBLM7.h +++ b/include/configs/MVBLM7.h @@ -28,7 +28,6 @@ #define CONFIG_PCI #define CONFIG_PCI_INDIRECT_BRIDGE #define CONFIG_PCI_SKIP_HOST_BRIDGE -#define CONFIG_HARD_I2C #define CONFIG_TSEC_ENET #define CONFIG_MPC8XXX_SPI #define CONFIG_HARD_SPI @@ -36,13 +35,14 @@ #define CONFIG_MISC_INIT_R /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 - -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 100000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * DDR Setup diff --git a/include/configs/OCRTC.h b/include/configs/OCRTC.h index be2ecf4640..c919613519 100644 --- a/include/configs/OCRTC.h +++ b/include/configs/OCRTC.h @@ -201,10 +201,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC08) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/ORSG.h b/include/configs/ORSG.h index fb0b89db9e..56d251cea5 100644 --- a/include/configs/ORSG.h +++ b/include/configs/ORSG.h @@ -197,10 +197,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC08) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h index 3fe4108219..ba3f7c2821 100644 --- a/include/configs/P1010RDB.h +++ b/include/configs/P1010RDB.h @@ -473,15 +473,15 @@ extern unsigned long get_sdram_size(void); #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C EEPROM */ #undef CONFIG_ID_EEPROM diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index 0391a96a54..d1ce9fdc8d 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -358,15 +358,15 @@ #define CONFIG_FIT_VERBOSE /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h index 6b7579baf0..cd6d20c729 100644 --- a/include/configs/P1023RDB.h +++ b/include/configs/P1023RDB.h @@ -188,13 +188,14 @@ extern unsigned long get_clock_freq(void); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h index 3ebec6b590..a8202c67fd 100644 --- a/include/configs/P1023RDS.h +++ b/include/configs/P1023RDS.h @@ -297,15 +297,15 @@ extern unsigned long get_clock_freq(void); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x51 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h index 447cd98daf..adaed564f7 100644 --- a/include/configs/P1_P2_RDB.h +++ b/include/configs/P1_P2_RDB.h @@ -351,16 +351,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } /* * I2C2 EEPROM diff --git a/include/configs/P2020COME.h b/include/configs/P2020COME.h index d1c9b24810..08d1c25914 100644 --- a/include/configs/P2020COME.h +++ b/include/configs/P2020COME.h @@ -209,16 +209,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_FIT_VERBOSE 1 /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address*/ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * I2C2 EEPROM diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h index 9df116e26b..b5078cdb52 100644 --- a/include/configs/P2020DS.h +++ b/include/configs/P2020DS.h @@ -371,15 +371,16 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } /* * I2C2 EEPROM diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index 43387d7492..9814ca2012 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -351,14 +351,14 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x118000 -#define CONFIG_SYS_I2C2_OFFSET 0x118100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * RapidIO diff --git a/include/configs/PCI405.h b/include/configs/PCI405.h index 626a5463b6..a71a5219cf 100644 --- a/include/configs/PCI405.h +++ b/include/configs/PCI405.h @@ -193,10 +193,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h index 036fec8cd8..2251ca6116 100644 --- a/include/configs/PIP405.h +++ b/include/configs/PIP405.h @@ -71,10 +71,11 @@ * EEPROM of the SDRAM * The Atmel EEPROM uses 16Bit addressing. ***************************************************************/ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 50000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h index 75c0926853..3c31cfb01a 100644 --- a/include/configs/PLU405.h +++ b/include/configs/PLU405.h @@ -265,10 +265,11 @@ /* * I2C EEPROM (24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24WC16 */ #define CONFIG_SYS_EEPROM_WREN 1 diff --git a/include/configs/PM826.h b/include/configs/PM826.h index 2c4aa2fd61..b466513ea3 100644 --- a/include/configs/PM826.h +++ b/include/configs/PM826.h @@ -41,10 +41,10 @@ "bootm" /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -# define CONFIG_SYS_I2C_SPEED 50000 -# define CONFIG_SYS_I2C_SLAVE 0xFE +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ diff --git a/include/configs/PM828.h b/include/configs/PM828.h index dbf980126b..cb68c41bab 100644 --- a/include/configs/PM828.h +++ b/include/configs/PM828.h @@ -41,10 +41,10 @@ "bootm" /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -# define CONFIG_SYS_I2C_SPEED 50000 -# define CONFIG_SYS_I2C_SLAVE 0xFE +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ diff --git a/include/configs/PMC405.h b/include/configs/PMC405.h index fbee0930d8..67a96d29d4 100644 --- a/include/configs/PMC405.h +++ b/include/configs/PMC405.h @@ -223,10 +223,11 @@ /* * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24W16 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/PMC405DE.h b/include/configs/PMC405DE.h index 22b1177ace..531e95612a 100644 --- a/include/configs/PMC405DE.h +++ b/include/configs/PMC405DE.h @@ -201,10 +201,11 @@ /* * I2C EEPROM (24W16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24W16 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h index 1b81861ac7..a54c099ce4 100644 --- a/include/configs/PMC440.h +++ b/include/configs/PMC440.h @@ -212,13 +212,14 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -#define CONFIG_I2C_MULTI_BUS 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_PPC4XX_CH1 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F #define CONFIG_SYS_I2C_MULTI_EEPROMS diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h index 1aaa8b0ae8..cd9eb4b10b 100644 --- a/include/configs/PPChameleonEVB.h +++ b/include/configs/PPChameleonEVB.h @@ -406,10 +406,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/R360MPI.h b/include/configs/R360MPI.h index 9ab524f4bf..efe699538c 100644 --- a/include/configs/R360MPI.h +++ b/include/configs/R360MPI.h @@ -81,10 +81,13 @@ #define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ #define CONFIG_HARD_I2C 1 /* To I2C with hardware support */ -#undef CONFIG_SORT_I2C /* To I2C with software support */ +#undef CONFIG_SYS_I2C_SOFT /* To I2C with software support */ #define CONFIG_SYS_I2C_SPEED 4700 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F +#if defined(CONFIG_SYS_I2C_SOFT) +#define CONFIG_SYS_SYS_I2C_SOFT_SPEED 4700 /* I2C speed and slave address */ +#define CONFIG_SYS_SYS_I2C_SOFT_SLAVE 0x7F /* * Software (bit-bang) I2C driver configuration */ @@ -100,6 +103,7 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(50) +#endif /* #define(CONFIG_SYS_I2C_SOFT) */ #define CONFIG_SYS_I2C_LCD_ADDR 0x8 /* LCD Control */ #define CONFIG_SYS_I2C_KEY_ADDR 0x9 /* Keyboard coprocessor */ diff --git a/include/configs/RPXClassic.h b/include/configs/RPXClassic.h index b0b0c91e4a..6ba8a02bcb 100644 --- a/include/configs/RPXClassic.h +++ b/include/configs/RPXClassic.h @@ -132,14 +132,16 @@ * I2C Configuration *----------------------------------------------------------------------------- */ -#define CONFIG_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0x34 +#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C_SLAVE 0x34 /* enable I2C and select the hardware/software driver */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ + +#if defined(CONFIG_SYS_I2C_SOFT) +#define CONFIG_SYS_I2C 1 /* * Software (bit-bang) I2C driver configuration */ @@ -154,8 +156,10 @@ #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -# define CONFIG_SYS_I2C_SPEED 50000 -# define CONFIG_SYS_I2C_SLAVE 0x34 +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x34 +#endif + # define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */ # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ diff --git a/include/configs/RPXlite.h b/include/configs/RPXlite.h index 28132566df..ada7e145c0 100644 --- a/include/configs/RPXlite.h +++ b/include/configs/RPXlite.h @@ -46,6 +46,36 @@ #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ #define CONFIG_BZIP2 /* Include support for bzip2 compressed images */ + +/* enable I2C and select the hardware/software driver */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 40000 /* 40 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE +/* Software (bit-bang) I2C driver configuration */ +#define PB_SCL 0x00000020 /* PB 26 */ +#define PB_SDA 0x00000010 /* PB 27 */ + +#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) +#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) +#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) +#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) +#define I2C_SDA(bit) if (bit) \ + immr->im_cpm.cp_pbdat |= PB_SDA; \ + else \ + immr->im_cpm.cp_pbdat &= ~PB_SDA +#define I2C_SCL(bit) if (bit) \ + immr->im_cpm.cp_pbdat |= PB_SCL; \ + else \ + immr->im_cpm.cp_pbdat &= ~PB_SCL +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +/* M41T11 Serial Access Timekeeper(R) SRAM */ +#define CONFIG_RTC_M41T11 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +/* play along with the linux driver */ +#define CONFIG_SYS_M41T11_BASE_YEAR 1900 + #undef CONFIG_WATCHDOG /* watchdog disabled */ /* diff --git a/include/configs/RRvision.h b/include/configs/RRvision.h index 61ada9573d..06273a2ae1 100644 --- a/include/configs/RRvision.h +++ b/include/configs/RRvision.h @@ -106,13 +106,10 @@ #endif /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C /* I2C bit-banged */ - -# define CONFIG_SYS_I2C_SPEED 50000 /* 50 kHz is supposed to work */ -# define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -128,7 +125,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(1) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ /* diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h index f5d6135870..3448ef35a8 100644 --- a/include/configs/SIMPC8313.h +++ b/include/configs/SIMPC8313.h @@ -229,14 +229,15 @@ #define CONFIG_SYS_HUSH_PARSER /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * General PCI diff --git a/include/configs/SXNI855T.h b/include/configs/SXNI855T.h index dfb1426751..e2b05de381 100644 --- a/include/configs/SXNI855T.h +++ b/include/configs/SXNI855T.h @@ -104,7 +104,10 @@ #define CONFIG_RTC_DS1306 /* Dallas 1306 real time clock */ -#define CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -121,8 +124,6 @@ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -# define CONFIG_SYS_I2C_SPEED 50000 -# define CONFIG_SYS_I2C_SLAVE 0xFE # define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Atmel 24C64 */ # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* two byte address */ diff --git a/include/configs/Sandpoint8240.h b/include/configs/Sandpoint8240.h index c5e0339268..ed8a32f7df 100644 --- a/include/configs/Sandpoint8240.h +++ b/include/configs/Sandpoint8240.h @@ -186,13 +186,16 @@ * If the software driver is chosen, there are some additional * configuration items that the driver uses to drive the port pins. */ -#define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_HARD_I2C 1 /* To enable I2C support */ +#undef CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT #error "Soft I2C is not configured properly. Please review!" +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE #define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ #define I2C_ACTIVE (iop->pdir |= 0x00010000) #define I2C_TRISTATE (iop->pdir &= ~0x00010000) @@ -202,7 +205,7 @@ #define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ else iop->pdat &= ~0x00020000 #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ +#endif /* CONFIG_SYS_I2C_SOFT */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */ diff --git a/include/configs/Sandpoint8245.h b/include/configs/Sandpoint8245.h index e1692dc0b2..97e8968243 100644 --- a/include/configs/Sandpoint8245.h +++ b/include/configs/Sandpoint8245.h @@ -156,13 +156,16 @@ * If the software driver is chosen, there are some additional * configuration items that the driver uses to drive the port pins. */ -#define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_HARD_I2C 1 /* To enable I2C support */ +#undef CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C_SPEED 400000 +#define CONFIG_SYS_I2C_SLAVE 0x7F -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT #error "Soft I2C is not configured properly. Please review!" +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE #define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ #define I2C_ACTIVE (iop->pdir |= 0x00010000) #define I2C_TRISTATE (iop->pdir &= ~0x00010000) @@ -172,7 +175,7 @@ #define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ else iop->pdat &= ~0x00020000 #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ +#endif /* CONFIG_SYS_I2C_SOFT */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/TASREG.h b/include/configs/TASREG.h index 494ed078f8..bce4176f9d 100644 --- a/include/configs/TASREG.h +++ b/include/configs/TASREG.h @@ -120,19 +120,11 @@ /*----------------------------------------------------------------------- * I2C */ -#define CONFIG_SOFT_I2C -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ - /* 32 byte page write mode using*/ - /* last 5 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 100000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F -#if defined (CONFIG_SOFT_I2C) #if 0 /* push-pull */ #define SDA 0x00800000 #define SCL 0x00000008 @@ -166,7 +158,17 @@ #define I2C_ACTIVE {DIR1|=SDA;} #define I2C_TRISTATE {DIR1&=~SDA;} #endif -#endif + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 +/* + * The Catalyst CAT24WC32 has 32 byte page write mode using + * last 5 bits of the address + */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in DPRAM) diff --git a/include/configs/TK885D.h b/include/configs/TK885D.h index 39c39ee8c9..7f2b842993 100644 --- a/include/configs/TK885D.h +++ b/include/configs/TK885D.h @@ -88,13 +88,10 @@ #undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -110,7 +107,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C?? */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* two byte address */ diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h index 3c7addbb54..00056a33d4 100644 --- a/include/configs/TOP5200.h +++ b/include/configs/TOP5200.h @@ -184,10 +184,13 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_MISC_INIT_R -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C with softwate support */ +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ -#if defined (CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) +# define CONFIG_SYS_I2C +# define CONFIG_SYS_I2C_SOFT_SPEED 100000 +# define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F +/**/ # define SDA0 0x40 # define SCL0 0x80 # define GPIOE0 *((volatile uchar*)(CONFIG_SYS_MBAR+0x0c00)) @@ -202,8 +205,7 @@ # define I2C_DELAY {udelay(5);} # define I2C_ACTIVE {DDR0|=SDA0;} # define I2C_TRISTATE {DDR0&=~SDA0;} -# define CONFIG_SYS_I2C_SPEED 100000 -# define CONFIG_SYS_I2C_SLAVE 0x7F + #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 #define CONFIG_SYS_I2C_FACT_ADDR 0x57 #endif diff --git a/include/configs/TOP860.h b/include/configs/TOP860.h index c2210503a0..5c5ce84ff1 100644 --- a/include/configs/TOP860.h +++ b/include/configs/TOP860.h @@ -143,7 +143,6 @@ * Environment handler * only the first 6k in EEPROM are available for user. Of that we use 256b */ -#define CONFIG_SOFT_I2C #define CONFIG_ENV_IS_IN_EEPROM 1 /* turn on EEPROM env feature */ #define CONFIG_ENV_OFFSET 0x1000 #define CONFIG_ENV_SIZE 0x0700 @@ -154,13 +153,15 @@ #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 #define CONFIG_SYS_EEPROM_SIZE 0x2000 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0xFE #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 #define CONFIG_ENV_OVERWRITE #define CONFIG_MISC_INIT_R -#if defined (CONFIG_SOFT_I2C) +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 100000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE +/**/ #define SDA 0x00010 #define SCL 0x00020 #define __I2C_DIR immr->im_cpm.cp_pbdir @@ -177,7 +178,6 @@ #define I2C_DELAY { udelay(5); } #define I2C_ACTIVE { __I2C_DIR |= SDA; } #define I2C_TRISTATE { __I2C_DIR &= ~SDA; } -#endif #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h index 006d53d345..1b02cbbca7 100644 --- a/include/configs/TQM8260.h +++ b/include/configs/TQM8260.h @@ -73,10 +73,10 @@ #define CONFIG_BOOTCOMMAND "run flash_self" /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 400000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F /* * Software (bit-bang) I2C driver configuration diff --git a/include/configs/TQM8272.h b/include/configs/TQM8272.h index c5b64b245a..3f586fbbc1 100644 --- a/include/configs/TQM8272.h +++ b/include/configs/TQM8272.h @@ -81,11 +81,10 @@ #if CONFIG_I2C /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 400000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F /* * Software (bit-bang) I2C driver configuration */ @@ -119,8 +118,9 @@ #define CONFIG_SYS_DTT_HYSTERESIS 3 #else +#undef CONFIG_SYS_I2C #undef CONFIG_HARD_I2C -#undef CONFIG_SOFT_I2C +#undef CONFIG_SYS_I2C_SOFT #endif /* diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index 8eb217c5d8..07b5acb977 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -171,12 +171,11 @@ /* * I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed: 400KHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 /* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h index a893316efc..37e3541d68 100644 --- a/include/configs/TQM855M.h +++ b/include/configs/TQM855M.h @@ -77,13 +77,10 @@ #undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -99,7 +96,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* two byte address */ diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h index f28aa16c02..9cf263cff6 100644 --- a/include/configs/TQM866M.h +++ b/include/configs/TQM866M.h @@ -91,13 +91,11 @@ #undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C /* * Software (bit-bang) I2C driver configuration */ @@ -113,7 +111,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C256 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* two byte address */ diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h index e6b1e35d54..1f52efcf5b 100644 --- a/include/configs/TQM885D.h +++ b/include/configs/TQM885D.h @@ -85,13 +85,10 @@ #undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -107,7 +104,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C?? */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* two byte address */ diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h index 6316fb566a..a1dad2b5bb 100644 --- a/include/configs/VOH405.h +++ b/include/configs/VOH405.h @@ -264,10 +264,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */ #define CONFIG_SYS_EEPROM_WREN 1 diff --git a/include/configs/VOM405.h b/include/configs/VOM405.h index f3bd423b46..5daf175863 100644 --- a/include/configs/VOM405.h +++ b/include/configs/VOM405.h @@ -189,10 +189,11 @@ /* * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/W7OLMC.h b/include/configs/W7OLMC.h index f388047ee5..51cfcf6e21 100644 --- a/include/configs/W7OLMC.h +++ b/include/configs/W7OLMC.h @@ -263,10 +263,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC08) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h index dba456108c..6769c0d806 100644 --- a/include/configs/W7OLMG.h +++ b/include/configs/W7OLMG.h @@ -270,10 +270,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (ATMEL 24C04N) */ -#define CONFIG_HARD_I2C 1 /* Hardware assisted I2C */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h index df4652153c..f38d90ee3f 100644 --- a/include/configs/WUH405.h +++ b/include/configs/WUH405.h @@ -228,10 +228,11 @@ /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC16) for environment */ -#define CONFIG_HARD_I2C /* I2c with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/acadia.h b/include/configs/acadia.h index 88c4aee153..f79706e1d2 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -190,7 +190,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/alpr.h b/include/configs/alpr.h index b9b4e9af99..5431b098c5 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -105,12 +105,12 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ /*----------------------------------------------------------------------- * I2C EEPROM (PCF8594C) diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h index 72f75aae66..580d079ed1 100644 --- a/include/configs/amcc-common.h +++ b/include/configs/amcc-common.h @@ -29,9 +29,10 @@ /* * I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* * Ethernet/EMAC/PHY diff --git a/include/configs/aria.h b/include/configs/aria.h index c9d090e000..68f25ea388 100644 --- a/include/configs/aria.h +++ b/include/configs/aria.h @@ -355,7 +355,6 @@ /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */ #define CONFIG_I2C_MULTI_BUS /* I2C speed and slave address */ diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h index 1124f0a29a..ed9400e4c0 100644 --- a/include/configs/astro_mcf5373l.h +++ b/include/configs/astro_mcf5373l.h @@ -100,12 +100,11 @@ #undef CONFIG_MCFPIT /* I2C */ -#define CONFIG_FSL_I2C -#define CONFIG_HARD_I2C /* I2C with hw support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 80000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 80000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR /* diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index e585efe4d3..5336f69103 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -206,7 +206,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/beaver.h b/include/configs/beaver.h index 628d5d3db1..801caca24f 100644 --- a/include/configs/beaver.h +++ b/include/configs/beaver.h @@ -41,12 +41,11 @@ #define CONFIG_BOARD_EARLY_INIT_F /* I2C */ -#define CONFIG_TEGRA_I2C +#define CONFIG_SYS_I2C_TEGRA #define CONFIG_SYS_I2C_INIT_BOARD -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_MAX_I2C_BUS TEGRA_I2C_NUM_CONTROLLERS #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C /* SD/MMC */ #define CONFIG_MMC diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h index c1a5ecda7e..beab1271a4 100644 --- a/include/configs/bf533-ezkit.h +++ b/include/configs/bf533-ezkit.h @@ -94,10 +94,15 @@ /* * I2C Settings */ -#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C_SOFT +#ifdef CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1 - +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#endif /* * Misc Settings diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h index e3344e9e85..7144c6319f 100644 --- a/include/configs/bf533-stamp.h +++ b/include/configs/bf533-stamp.h @@ -14,7 +14,6 @@ #define CONFIG_BFIN_CPU bf533-0.3 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS - /* * Clock Settings * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV @@ -38,7 +37,6 @@ /* Values can range from 1-15 */ #define CONFIG_SCLK_DIV 6 /* note: 1.2 boards can go faster */ - /* * Memory Settings */ @@ -74,6 +72,42 @@ /* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0 +/* + * Software (bit-bang) I2C driver configuration + */ +#define PF_SCL PF3 +#define PF_SDA PF2 +#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") +#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); \ + *pFIO_INEN &= ~PF_SDA; asm("ssync;") +#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); \ + *pFIO_INEN |= PF_SDA; asm("ssync;") +#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); \ + asm("ssync;") +#define I2C_SDA(bit) if (bit) { \ + *pFIO_FLAG_S = PF_SDA; \ + asm("ssync;"); \ + } \ + else { \ + *pFIO_FLAG_C = PF_SDA; \ + asm("ssync;"); \ + } +#define I2C_SCL(bit) if (bit) { \ + *pFIO_FLAG_S = PF_SCL; \ + asm("ssync;"); \ + } \ + else { \ + *pFIO_FLAG_C = PF_SCL; \ + asm("ssync;"); \ + } +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + + /* * Flash Settings */ @@ -84,7 +118,6 @@ #define CONFIG_SYS_MAX_FLASH_BANKS 1 #define CONFIG_SYS_MAX_FLASH_SECT 67 - /* * SPI Settings */ @@ -132,10 +165,15 @@ /* * I2C Settings */ -#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C_SOFT +#ifdef CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2 - +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0 +#endif /* * Compact Flash / IDE / ATA Settings diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h index 6ee1e4c869..404039ac23 100644 --- a/include/configs/bf561-ezkit.h +++ b/include/configs/bf561-ezkit.h @@ -88,10 +88,14 @@ /* * I2C Settings */ -#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C_SOFT +#ifdef CONFIG_SYS_I2C_SOFT #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1 - +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0 +#endif /* * Misc Settings diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h index e1a6fe3056..08ccce0b9a 100644 --- a/include/configs/bfin_adi_common.h +++ b/include/configs/bfin_adi_common.h @@ -71,7 +71,7 @@ # ifdef CONFIG_SPI_FLASH # define CONFIG_CMD_SF # endif -# if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +# if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) # define CONFIG_CMD_I2C # define CONFIG_SOFT_I2C_READ_REPEATED_START # endif @@ -299,7 +299,7 @@ /* * I2C Settings */ -#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) # ifndef CONFIG_SYS_I2C_SPEED # define CONFIG_SYS_I2C_SPEED 50000 # endif diff --git a/include/configs/blackstamp.h b/include/configs/blackstamp.h index 83ad659cdf..7d8227503a 100644 --- a/include/configs/blackstamp.h +++ b/include/configs/blackstamp.h @@ -40,7 +40,6 @@ #define SHARED_RESOURCES 1 /* Is I2C bit-banged? */ -#undef CONFIG_SOFT_I2 /* * Clock Settings @@ -115,7 +114,7 @@ # undef CONFIG_CMD_NET #endif -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT # define CONFIG_CMD_I2C #endif @@ -204,11 +203,11 @@ * Note these pins are arbitrarily chosen because we aren't using * them yet. You can (and probably should) change these values! */ -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8 -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0xFE +#define CONFIG_SYS_SOFT_I2C_SPEED 50000 +#define CONFIG_SYS_SOFT_I2C_SLAVE 0xFE #endif /* diff --git a/include/configs/blackvme.h b/include/configs/blackvme.h index 523c4e409a..cd37f9adb9 100644 --- a/include/configs/blackvme.h +++ b/include/configs/blackvme.h @@ -224,7 +224,7 @@ * Soft I2C settings (BF561 does not have hard I2C) * PF12,13 on SPI connector 0. */ -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT # define CONFIG_CMD_I2C # define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF12 # define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF13 diff --git a/include/configs/bluestone.h b/include/configs/bluestone.h index 5ea6f46bee..33e04963e6 100644 --- a/include/configs/bluestone.h +++ b/include/configs/bluestone.h @@ -109,7 +109,7 @@ /* * I2C */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h index b02f86207a..9301fccbdc 100644 --- a/include/configs/bubinga.h +++ b/include/configs/bubinga.h @@ -118,9 +118,9 @@ * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_NOPROBES { 0x69 } /* avoid i2c probe hangup (why?) */ +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* avoid i2c probe hangup (?) */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #if defined(CONFIG_CMD_EEPROM) diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index 4353a8cb2b..f6faeec06c 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -316,7 +316,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/cardhu.h b/include/configs/cardhu.h index 142d20b5c5..4abb03ea56 100644 --- a/include/configs/cardhu.h +++ b/include/configs/cardhu.h @@ -40,12 +40,13 @@ #define CONFIG_BOARD_EARLY_INIT_F /* I2C */ -#define CONFIG_TEGRA_I2C +#define CONFIG_SYS_I2C_TEGRA #define CONFIG_SYS_I2C_INIT_BOARD #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_MAX_I2C_BUS TEGRA_I2C_NUM_CONTROLLERS #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C /* SD/MMC */ #define CONFIG_MMC diff --git a/include/configs/controlcenterd.h b/include/configs/controlcenterd.h index cdd79f0769..c6aad01dba 100644 --- a/include/configs/controlcenterd.h +++ b/include/configs/controlcenterd.h @@ -192,15 +192,14 @@ /* * I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_CMD_I2C - -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* Probing DP501 I2C-Bridge will hang */ #define CONFIG_SYS_I2C_NOPROBES { {0, 0x30}, {0, 0x37}, {0, 0x3a}, \ {0, 0x3b}, {0, 0x50} } diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index a85680f103..c0591c5277 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -346,14 +346,14 @@ #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x118000 -#define CONFIG_SYS_I2C2_OFFSET 0x118100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 /* * RapidIO diff --git a/include/configs/cpuat91.h b/include/configs/cpuat91.h index 4a7c4fc288..c56fdd7517 100644 --- a/include/configs/cpuat91.h +++ b/include/configs/cpuat91.h @@ -76,7 +76,6 @@ #define CONFIG_USART_ID 0/* ignored in arm */ #undef CONFIG_HARD_I2C -#undef CONFIG_SOFT_I2C #define AT91_PIN_SDA (1<<25) #define AT91_PIN_SCL (1<<26) @@ -123,7 +122,7 @@ #undef CONFIG_CMD_NFS #undef CONFIG_CMD_DHCP -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_I2C #endif diff --git a/include/configs/csb272.h b/include/configs/csb272.h index 663b8cbd44..49a144fd33 100644 --- a/include/configs/csb272.h +++ b/include/configs/csb272.h @@ -159,10 +159,11 @@ * I2C configuration * */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* I2C slave address */ /* * MII PHY configuration diff --git a/include/configs/csb472.h b/include/configs/csb472.h index 6f7dc18567..7705a5dda8 100644 --- a/include/configs/csb472.h +++ b/include/configs/csb472.h @@ -158,10 +158,11 @@ * I2C configuration * */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* I2C slave address */ /* * MII PHY configuration diff --git a/include/configs/dalmore.h b/include/configs/dalmore.h index b6e01617c8..145e7ac926 100644 --- a/include/configs/dalmore.h +++ b/include/configs/dalmore.h @@ -43,12 +43,13 @@ #define CONFIG_BOARD_EARLY_INIT_F /* I2C */ -#define CONFIG_TEGRA_I2C +#define CONFIG_SYS_I2C_TEGRA #define CONFIG_SYS_I2C_INIT_BOARD #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_MAX_I2C_BUS TEGRA_I2C_NUM_CONTROLLERS #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C /* SD/MMC */ #define CONFIG_MMC diff --git a/include/configs/debris.h b/include/configs/debris.h index 660cceebd8..c9fb8d78cb 100644 --- a/include/configs/debris.h +++ b/include/configs/debris.h @@ -257,12 +257,15 @@ * configuration items that the driver uses to drive the port pins. */ #define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT #error "Soft I2C is not configured properly. Please review!" +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F #define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ #define I2C_ACTIVE (iop->pdir |= 0x00010000) #define I2C_TRISTATE (iop->pdir &= ~0x00010000) @@ -272,7 +275,7 @@ #define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ else iop->pdat &= ~0x00020000 #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ +#endif /* CONFIG_SYS_I2C_SOFT */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/dlvision-10g.h b/include/configs/dlvision-10g.h index 84af895781..17391cddc9 100644 --- a/include/configs/dlvision-10g.h +++ b/include/configs/dlvision-10g.h @@ -98,7 +98,7 @@ /* * I2C stuff */ -#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 /* Temp sensor/hwmon/dtt */ #define CONFIG_DTT_LM63 1 /* National LM63 */ diff --git a/include/configs/dlvision.h b/include/configs/dlvision.h index d5bf735581..27471284ac 100644 --- a/include/configs/dlvision.h +++ b/include/configs/dlvision.h @@ -91,7 +91,7 @@ /* * I2C stuff */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address*/ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 /* * FLASH organization diff --git a/include/configs/eXalion.h b/include/configs/eXalion.h index 6d9e2ad96a..c2d04a21c7 100644 --- a/include/configs/eXalion.h +++ b/include/configs/eXalion.h @@ -208,7 +208,7 @@ * configuration items that the driver uses to drive the port pins. */ #define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F diff --git a/include/configs/eb_cpu5282.h b/include/configs/eb_cpu5282.h index 84cf9d74fc..08ba883f4c 100644 --- a/include/configs/eb_cpu5282.h +++ b/include/configs/eb_cpu5282.h @@ -246,14 +246,14 @@ * I2C */ -#define CONFIG_HARD_I2C -#define CONFIG_FSL_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_FSL_I2C_OFFSET 0x00000300 #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0 +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0 #ifdef CONFIG_CMD_DATE #define CONFIG_RTC_DS1338 diff --git a/include/configs/eb_cpux9k2.h b/include/configs/eb_cpux9k2.h index a768ef3a32..247e37b6dd 100644 --- a/include/configs/eb_cpux9k2.h +++ b/include/configs/eb_cpux9k2.h @@ -207,11 +207,10 @@ * I2C-Bus */ -#define CONFIG_SYS_I2C_SPEED 50000 -#define CONFIG_SYS_I2C_SLAVE 0 /* not used */ - -#ifndef CONFIG_HARD_I2C -#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0 /* Software I2C driver configuration */ @@ -235,9 +234,7 @@ else \ writel(ATMEL_PMX_AA_TWCK, &pio->pioa.codr); -#define I2C_DELAY udelay(2500000/CONFIG_SYS_I2C_SPEED) - -#endif /* CONFIG_HARD_I2C */ +#define I2C_DELAY udelay(2500000/CONFIG_SYS_I2C_SOFT_SPEED) /* I2C-RTC */ diff --git a/include/configs/ebony.h b/include/configs/ebony.h index 800af72766..47014f9e30 100644 --- a/include/configs/ebony.h +++ b/include/configs/ebony.h @@ -122,7 +122,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h index 5fdc46aa2d..aba3392234 100644 --- a/include/configs/ep8260.h +++ b/include/configs/ep8260.h @@ -211,15 +211,18 @@ * If the software driver is chosen, there are some additional * configuration items that the driver uses to drive the port pins. */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ + #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SLAVE 0x7F /* This is for HARD, must go */ /* * Software (bit-bang) I2C driver configuration */ -#ifdef CONFIG_SOFT_I2C +#ifdef CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE #define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ #define I2C_ACTIVE (iop->pdir |= 0x00010000) #define I2C_TRISTATE (iop->pdir &= ~0x00010000) @@ -229,7 +232,7 @@ #define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ else iop->pdat &= ~0x00020000 #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ +#endif /* CONFIG_SYS_I2C_SOFT */ /* #define CONFIG_RTC_DS174x */ diff --git a/include/configs/ethernut5.h b/include/configs/ethernut5.h index 3cf27edcdc..adf14be365 100644 --- a/include/configs/ethernut5.h +++ b/include/configs/ethernut5.h @@ -194,10 +194,12 @@ /* I2C */ #define CONFIG_SYS_MAX_I2C_BUS 1 -#define CONFIG_SYS_I2C_SLAVE 0 -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 100000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0 + #define I2C_SOFT_DECLARATIONS #define GPIO_I2C_SCL AT91_PIO_PORTA, 24 diff --git a/include/configs/gdppc440etx.h b/include/configs/gdppc440etx.h index c95cb00e9e..cfb2a72716 100644 --- a/include/configs/gdppc440etx.h +++ b/include/configs/gdppc440etx.h @@ -129,7 +129,7 @@ /* * I2C */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed+slave address*/ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 /* * Default environment variables diff --git a/include/configs/ibf-dsp561.h b/include/configs/ibf-dsp561.h index 294af735d6..5291755121 100644 --- a/include/configs/ibf-dsp561.h +++ b/include/configs/ibf-dsp561.h @@ -105,11 +105,11 @@ /* * I2C Settings */ -#define CONFIG_SOFT_I2C 1 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1 - /* * Misc Settings */ diff --git a/include/configs/icon.h b/include/configs/icon.h index fd8d56fe46..eafcf5aeaf 100644 --- a/include/configs/icon.h +++ b/include/configs/icon.h @@ -104,9 +104,8 @@ /* * I2C */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_SPD_BUS_NUM 0 /* The I2C bus for SPD */ #define CONFIG_SYS_I2C_MULTI_EEPROMS diff --git a/include/configs/intip.h b/include/configs/intip.h index fed0c3c23c..d3d7a441b6 100644 --- a/include/configs/intip.h +++ b/include/configs/intip.h @@ -215,7 +215,7 @@ /* * I2C */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/io.h b/include/configs/io.h index af01ae25b3..33743e61ac 100644 --- a/include/configs/io.h +++ b/include/configs/io.h @@ -98,7 +98,7 @@ /* * I2C stuff */ -#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 /* Temp sensor/hwmon/dtt */ #define CONFIG_DTT_LM63 1 /* National LM63 */ diff --git a/include/configs/io64.h b/include/configs/io64.h index 274625dbd4..dcd1b82e25 100644 --- a/include/configs/io64.h +++ b/include/configs/io64.h @@ -324,7 +324,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_PCA9698 1 /* NXP PCA9698 */ diff --git a/include/configs/iocon.h b/include/configs/iocon.h index bae525026e..32d9050adb 100644 --- a/include/configs/iocon.h +++ b/include/configs/iocon.h @@ -94,11 +94,11 @@ /* * I2C stuff */ -#define CONFIG_SYS_I2C_SPEED 400000 - -/* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* * Software (bit-bang) I2C driver configuration diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 10871e8349..ca0df2d0ce 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -103,9 +103,8 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 -#define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_SPD_BUS_NUM 0 /* The I2C bus for SPD */ #define IIC0_BOOTPROM_ADDR 0x50 diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 613654c511..bd3bbb79a5 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -369,7 +369,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ diff --git a/include/configs/km/keymile-common.h b/include/configs/km/keymile-common.h index d0e4b3fd47..a82987d6a0 100644 --- a/include/configs/km/keymile-common.h +++ b/include/configs/km/keymile-common.h @@ -62,10 +62,7 @@ #define CONFIG_LOADS_ECHO #define CONFIG_SYS_LOADS_BAUD_CHANGE -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_MAX_I2C_BUS 1 #define CONFIG_SYS_I2C_INIT_BOARD -#define CONFIG_I2C_MUX /* Support the IVM EEprom */ #define CONFIG_SYS_IVM_EEPROM_ADR 0x50 diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h index 6b3a4cca30..0ff866a896 100644 --- a/include/configs/km/km83xx-common.h +++ b/include/configs/km/km83xx-common.h @@ -201,11 +201,23 @@ #endif /* CFG_SYS_RAMBOOT */ /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_NUM_I2C_BUSES 4 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 200000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 200000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ + {1, {I2C_NULL_HOP} } } + +#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 /* ON Semi's LM75 */ @@ -213,7 +225,7 @@ #define CONFIG_SYS_DTT_MAX_TEMP 70 #define CONFIG_SYS_DTT_LOW_TEMP -30 #define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) +#define CONFIG_SYS_DTT_BUS_NUM 1 #if defined(CONFIG_CMD_NAND) #define CONFIG_NAND_KMETER1 @@ -309,7 +321,6 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_KM_DEF_ENV \ CONFIG_KM_DEF_ARCH \ - "EEprom_ivm=pca9547:70:9\0" \ "newenv=" \ "prot off 0xF00C0000 +0x40000 && " \ "era 0xF00C0000 +0x40000\0" \ diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index 97bdeba15c..e0368cb894 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -42,7 +42,6 @@ #define CONFIG_CMD_NAND #define CONFIG_CMD_SF -#define CONFIG_SOFT_I2C /* I2C bit-banged */ /* SPI NOR Flash default params, used by sf commands */ #define CONFIG_SF_DEFAULT_SPEED 8100000 @@ -171,8 +170,23 @@ /* * I2C related stuff */ +#undef CONFIG_I2C_MVTWSI +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ + #define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */ -#if defined(CONFIG_SOFT_I2C) +#if defined(CONFIG_SYS_I2C_SOFT) + +#define CONFIG_SYS_NUM_I2C_BUSES 6 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \ + } + #ifndef __ASSEMBLY__ #include extern void __set_direction(unsigned pin, int high); @@ -195,6 +209,8 @@ int get_scl(void); #define I2C_DELAY udelay(1) #define I2C_SOFT_DECLARATIONS +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x0 +#define CONFIG_SYS_I2C_SOFT_SPEED 100000 #endif /* EEprom support 24C128, 24C256 valid for environment eeprom */ @@ -224,7 +240,7 @@ int get_scl(void); #define CONFIG_SYS_EEPROM_WREN #define CONFIG_ENV_OFFSET 0x0 /* no bracets! */ #define CONFIG_ENV_SIZE (0x2000 - CONFIG_ENV_OFFSET) -#define CONFIG_I2C_ENV_EEPROM_BUS KM_ENV_BUS "\0" +#define CONFIG_I2C_ENV_EEPROM_BUS KM_ENV_BUS #define CONFIG_ENV_OFFSET_REDUND 0x2000 /* no bracets! */ #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #endif @@ -263,7 +279,8 @@ int get_scl(void); #else #define CONFIG_KM_NEW_ENV \ "newenv=setenv addr 0x100000 && " \ - "i2c dev 1; mw.b ${addr} 0 4 && " \ + "i2c dev " __stringify(CONFIG_I2C_ENV_EEPROM_BUS) "; " \ + "mw.b ${addr} 0 4 && " \ "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \ " ${addr} " __stringify(CONFIG_ENV_OFFSET) " 4 && " \ "eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR) \ @@ -277,7 +294,6 @@ int get_scl(void); CONFIG_KM_DEF_ENV \ CONFIG_KM_NEW_ENV \ "arch=arm\0" \ - "EEprom_ivm=" KM_IVM_BUS "\0" \ "" #if defined(CONFIG_SYS_NO_FLASH) diff --git a/include/configs/km82xx.h b/include/configs/km82xx.h index b087cdb240..b23cb96274 100644 --- a/include/configs/km82xx.h +++ b/include/configs/km82xx.h @@ -196,7 +196,6 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_KM_BOARD_EXTRA_ENV \ CONFIG_KM_DEF_ENV \ - "EEprom_ivm=pca9544a:70:4 \0" \ "unlock=yes\0" \ "newenv=" \ "prot off 0xFE0C0000 +0x40000 && " \ @@ -226,10 +225,18 @@ #endif /* CONFIG_ENV_IS_IN_FLASH */ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_NUM_I2C_BUSES 3 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SPEED CONFIG_SYS_I2C_SOFT_SPEED +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F +#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9542, 0x70, 0} } }, \ + {0, {{I2C_MUX_PCA9542, 0x70, 1} } } } + +#define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ /* * Software (bit-bang) I2C driver configuration @@ -266,7 +273,7 @@ int get_scl(void); #define CONFIG_SYS_DTT_MAX_TEMP 70 #define CONFIG_SYS_DTT_LOW_TEMP -30 #define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) +#define CONFIG_SYS_DTT_BUS_NUM 2 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 diff --git a/include/configs/km_kirkwood.h b/include/configs/km_kirkwood.h index 68d1bf6c66..0e6073c642 100644 --- a/include/configs/km_kirkwood.h +++ b/include/configs/km_kirkwood.h @@ -26,18 +26,18 @@ #define CONFIG_IDENT_STRING "\nKeymile Kirkwood" #define CONFIG_HOSTNAME km_kirkwood #define CONFIG_KM_DISABLE_PCIE -#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/ +#define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ /* KM_KIRKWOOD_PCI */ #elif defined(CONFIG_KM_KIRKWOOD_PCI) #define CONFIG_IDENT_STRING "\nKeymile Kirkwood PCI" #define CONFIG_HOSTNAME km_kirkwood_pci -#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/ +#define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ #define CONFIG_KM_FPGA_CONFIG /* KM_NUSA */ #elif defined(CONFIG_KM_NUSA) -#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/ +#define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ #define CONFIG_IDENT_STRING "\nKeymile NUSA" #define CONFIG_HOSTNAME kmnusa #undef CONFIG_SYS_KWD_CONFIG @@ -53,7 +53,7 @@ #elif defined(CONFIG_KM_MGCOGE3UN) #define CONFIG_IDENT_STRING "\nKeymile COGE3UN" #define CONFIG_HOSTNAME mgcoge3un -#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/ +#define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ #undef CONFIG_SYS_KWD_CONFIG #define CONFIG_SYS_KWD_CONFIG \ $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-memphis.cfg @@ -65,7 +65,7 @@ /* KMCOGE5UN */ #elif defined(CONFIG_KM_COGE5UN) #define CONFIG_IDENT_STRING "\nKeymile COGE5UN" -#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/ +#define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ #undef CONFIG_SYS_KWD_CONFIG #define CONFIG_SYS_KWD_CONFIG \ $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage_256M8_1.cfg @@ -79,12 +79,12 @@ #elif defined(CONFIG_KM_PORTL2) #define CONFIG_IDENT_STRING "\nKeymile Port-L2" #define CONFIG_HOSTNAME portl2 -#define KM_IVM_BUS "pca9544a:70:9" /* I2C2 (Mux-Port 1)*/ +#define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ #define CONFIG_KM_PIGGY4_88E6061 /* KM_SUV31 */ #elif defined(CONFIG_KM_SUV31) -#define KM_IVM_BUS "pca9547:70:9" /* I2C2 (Mux-Port 1)*/ +#define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ #define CONFIG_IDENT_STRING "\nKeymile SUV31" #define CONFIG_HOSTNAME kmsuv31 #define CONFIG_KM_ENV_IS_IN_SPI_NOR @@ -98,7 +98,7 @@ #include "km/km_arm.h" #ifndef CONFIG_KM_ENV_IS_IN_SPI_NOR -#define KM_ENV_BUS "pca9544a:70:d" /* I2C2 (Mux-Port 5)*/ +#define KM_ENV_BUS 5 /* I2C2 (Mux-Port 5)*/ #endif #if defined(CONFIG_KM_PIGGY4_88E6352) diff --git a/include/configs/korat.h b/include/configs/korat.h index 3410733ed7..7c7a305175 100644 --- a/include/configs/korat.h +++ b/include/configs/korat.h @@ -142,11 +142,11 @@ /* * I2C */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/luan.h b/include/configs/luan.h index 37111acdfb..8ecdf8049d 100644 --- a/include/configs/luan.h +++ b/include/configs/luan.h @@ -118,7 +118,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h index a1cee6832c..459c047b71 100644 --- a/include/configs/lwmon.h +++ b/include/configs/lwmon.h @@ -130,13 +130,10 @@ #undef CONFIG_STATUS_LED /* Status LED disabled */ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -152,7 +149,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ #define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */ diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index e2c436ff97..8f5eb956ae 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -285,11 +285,11 @@ /* * I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* RTC */ #define CONFIG_SYS_I2C_EEPROM_CPU_ADDR 0x52 /* EEPROM (CPU Modul) */ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 520ab8c98c..e7ed917f84 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -185,7 +185,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h index 9a483e7448..b48872b267 100644 --- a/include/configs/mecp5123.h +++ b/include/configs/mecp5123.h @@ -250,7 +250,6 @@ /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ #define CONFIG_SYS_I2C_SLAVE 0x7F /* slave address */ diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h index 1ad023b905..85ae3671f1 100644 --- a/include/configs/mpc5121ads.h +++ b/include/configs/mpc5121ads.h @@ -344,7 +344,6 @@ /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F diff --git a/include/configs/mpc8308_p1m.h b/include/configs/mpc8308_p1m.h index 3927250ba0..6875cf4c5b 100644 --- a/include/configs/mpc8308_p1m.h +++ b/include/configs/mpc8308_p1m.h @@ -311,13 +311,14 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* * General PCI diff --git a/include/configs/mpq101.h b/include/configs/mpq101.h index 2ab2f8ff19..55d93da598 100644 --- a/include/configs/mpq101.h +++ b/include/configs/mpq101.h @@ -205,13 +205,15 @@ /* * I2C buses and peripherals */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7f -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* I2C RTC - M41T81 */ #define CONFIG_RTC_M41T62 diff --git a/include/configs/neo.h b/include/configs/neo.h index fede8b8b64..5abb8b1a75 100644 --- a/include/configs/neo.h +++ b/include/configs/neo.h @@ -101,7 +101,7 @@ /* * I2C stuff */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 /* RTC */ #define CONFIG_RTC_DS1337 diff --git a/include/configs/nhk8815.h b/include/configs/nhk8815.h index 1453285f6c..0997f49859 100644 --- a/include/configs/nhk8815.h +++ b/include/configs/nhk8815.h @@ -93,8 +93,11 @@ #ifndef __ASSEMBLY__ #include #define CONFIG_CMD_I2C -#define CONFIG_SOFT_I2C -#define CONFIG_SYS_I2C_SPEED 400000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT 1 /* I2C bit-banged */ +#define I2C_SOFT_DEFS +#define CONFIG_SYS_I2C_SOFT_SPEED 400000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F #define __SDA 63 #define __SCL 62 #define I2C_SDA(x) nmk_gpio_set(__SDA, x) diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h index 14d00abc62..60ee8da558 100644 --- a/include/configs/ocotea.h +++ b/include/configs/ocotea.h @@ -135,7 +135,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/otc570.h b/include/configs/otc570.h index 76b078fa73..543209cb9d 100644 --- a/include/configs/otc570.h +++ b/include/configs/otc570.h @@ -99,14 +99,13 @@ /* RTC and I2C stuff */ #define CONFIG_RTC_DS1338 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#undef CONFIG_HARD_I2C -#define CONFIG_SOFT_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#ifdef CONFIG_SOFT_I2C -# define CONFIG_I2C_CMD_TREE -# define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#ifdef CONFIG_SYS_I2C_SOFT +#define CONFIG_SYS_I2C_SOFT_SPEED 100000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F + /* Configure data and clock pins for pio */ # define I2C_INIT { \ at91_set_pio_output(AT91_PIO_PORTB, 4, 0); \ @@ -124,7 +123,7 @@ /* Set clock pin */ # define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTB, 5, bit) # define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ +#endif /* CONFIG_SYS_I2C_SOFT */ /* * BOOTP options diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index a061610ac9..1b0be23dd3 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -518,17 +518,16 @@ #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C spd and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} /* Don't probe this addr */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ /* diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h index 09d0e2342f..c4c50932c3 100644 --- a/include/configs/p3p440.h +++ b/include/configs/p3p440.h @@ -81,12 +81,12 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ /*----------------------------------------------------------------------- * I2C RTC diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h index e4eaa66ebf..5de8e98aca 100644 --- a/include/configs/pcs440ep.h +++ b/include/configs/pcs440ep.h @@ -123,11 +123,11 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa4>>1) #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 diff --git a/include/configs/pdnb3.h b/include/configs/pdnb3.h index 0a17abc499..c664010067 100644 --- a/include/configs/pdnb3.h +++ b/include/configs/pdnb3.h @@ -265,12 +265,10 @@ */ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 83000 /* 83 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 83000 /* 83 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ diff --git a/include/configs/quad100hd.h b/include/configs/quad100hd.h index 451a61dd34..a51f2d4faf 100644 --- a/include/configs/quad100hd.h +++ b/include/configs/quad100hd.h @@ -136,11 +136,11 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* bytes of address */ diff --git a/include/configs/redwood.h b/include/configs/redwood.h index 5ba47bf999..c8bd02e710 100644 --- a/include/configs/redwood.h +++ b/include/configs/redwood.h @@ -94,13 +94,13 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define IIC0_BOOTPROM_ADDR 0x50 #define IIC0_ALT_BOOTPROM_ADDR 0x54 /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_NOPROBES {0x50, 0x52, 0x53, 0x54} +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x50}, {0, 0x52}, {0, 0x53}, {0, 0x54} } #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h index b4c8e40d50..d0fafd7136 100644 --- a/include/configs/s5p_goni.h +++ b/include/configs/s5p_goni.h @@ -210,8 +210,10 @@ #define CONFIG_SOFT_I2C_GPIO_SCL s5pc110_gpio_get_nr(j4, 3) #define CONFIG_SOFT_I2C_GPIO_SDA s5pc110_gpio_get_nr(j4, 0) -#define CONFIG_SOFT_I2C 1 -#define CONFIG_SYS_I2C_SPEED 50000 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_MAX_I2C_BUS 7 #define CONFIG_USB_GADGET diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index eab81e7feb..97a4008e36 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -234,9 +234,11 @@ #define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_part1_get_nr(b, 7) #define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_part1_get_nr(b, 6) -#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0 #define CONFIG_SOFT_I2C_READ_REPEATED_START -#define CONFIG_SYS_I2C_SPEED 50000 #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_MAX_I2C_BUS 7 diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h index df20abb68d..d63d0c4f54 100644 --- a/include/configs/sacsng.h +++ b/include/configs/sacsng.h @@ -280,15 +280,13 @@ * If the software driver is chosen, there are some additional * configuration items that the driver uses to drive the port pins. */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 400000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F /* * Software (bit-bang) I2C driver configuration */ -#ifdef CONFIG_SOFT_I2C #define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ #define I2C_ACTIVE (iop->pdir |= 0x00010000) #define I2C_TRISTATE (iop->pdir &= ~0x00010000) @@ -298,7 +296,6 @@ #define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ else iop->pdat &= ~0x00020000 #define I2C_DELAY udelay(20) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ /* Define this to reserve an entire FLASH sector for * environment variables. Otherwise, the environment will be diff --git a/include/configs/sbc405.h b/include/configs/sbc405.h index 7a20d4d84c..072f97e602 100644 --- a/include/configs/sbc405.h +++ b/include/configs/sbc405.h @@ -152,11 +152,11 @@ #define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /*----------------------------------------------------------------------- * PCI stuff diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index afa587eeba..6f912ed2c3 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -288,15 +288,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS 1 /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C1_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C2_OFFSET +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69}, {1, 0x69} } /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ /* TSEC */ diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h index 3aae95e345..84be5246b9 100644 --- a/include/configs/sbc8548.h +++ b/include/configs/sbc8548.h @@ -428,13 +428,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 /* * General PCI diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index d740cfec8a..cf97db94c8 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -273,13 +273,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* * RapidIO MMU diff --git a/include/configs/sc3.h b/include/configs/sc3.h index 8508c22e03..a96ffbcec3 100644 --- a/include/configs/sc3.h +++ b/include/configs/sc3.h @@ -230,16 +230,16 @@ * IIC stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 #define I2C_INIT #define I2C_ACTIVE 0 #define I2C_TRISTATE 0 -#define CONFIG_SYS_I2C_SPEED 100000 /* use the standard 100kHz speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* mask valid bits */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* mask valid bits */ #define CONFIG_RTC_DS1337 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index c7718579c0..2a24ef3c64 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -41,12 +41,11 @@ #define CONFIG_BOARD_LATE_INIT /* Make sure LCD init is complete */ /* I2C */ -#define CONFIG_TEGRA_I2C +#define CONFIG_SYS_I2C_TEGRA #define CONFIG_SYS_I2C_INIT_BOARD -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_MAX_I2C_BUS 4 #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C /* SD/MMC */ #define CONFIG_MMC diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 44ed7556d4..d2dedac4ed 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -219,7 +219,7 @@ /* * I2C */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/snapper9260.h b/include/configs/snapper9260.h index 383d1ce013..17eb5f2455 100644 --- a/include/configs/snapper9260.h +++ b/include/configs/snapper9260.h @@ -90,11 +90,11 @@ #define CONFIG_SYS_PROMPT "Snapper> " /* I2C - Bit-bashed */ -#define CONFIG_SOFT_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 100000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F #define CONFIG_SOFT_I2C_READ_REPEATED_START -#define CONFIG_I2C_MULTI_BUS #define I2C_INIT do { \ at91_set_gpio_output(AT91_PIN_PA23, 1); \ at91_set_gpio_output(AT91_PIN_PA24, 1); \ diff --git a/include/configs/socrates.h b/include/configs/socrates.h index f5fe550a02..e73f9c174c 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -219,15 +219,14 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 102124 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 - -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 102124 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 102124 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C RTC */ #define CONFIG_RTC_RX8025 /* Use Epson rx8025 rtc via i2c */ diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h index 6d905dee26..564f3645c9 100644 --- a/include/configs/spc1920.h +++ b/include/configs/spc1920.h @@ -194,13 +194,10 @@ */ #if defined(CONFIG_CMD_I2C) /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -216,7 +213,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ #endif /*----------------------------------------------------------------------- diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index 80b46a0033..c7689a7290 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -162,18 +162,18 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 + #if 0 #define CONFIG_SYS_I2C_NOPROBES {0x00} /* Don't probe these addrs */ #else /* I did the 'if 0' so we could keep the syntax above if ever needed. */ #undef CONFIG_SYS_I2C_NOPROBES #endif -#define CONFIG_SYS_I2C_OFFSET 0x3000 /* RapdIO Map configuration, mapped 1:1. */ diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index fc0252339e..f5f7f54348 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -182,13 +182,12 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 #undef CONFIG_SYS_I2C_NOPROBES -#define CONFIG_SYS_I2C_OFFSET 0x3000 /* I2C RTC */ #define CONFIG_RTC_DS1337 /* This is really a DS1339 RTC */ diff --git a/include/configs/t3corp.h b/include/configs/t3corp.h index ce65e39daf..9ab99244cf 100644 --- a/include/configs/t3corp.h +++ b/include/configs/t3corp.h @@ -306,7 +306,7 @@ /* * I2C */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/t4qds.h b/include/configs/t4qds.h index 0344d0d973..1ed53dbbb1 100644 --- a/include/configs/t4qds.h +++ b/include/configs/t4qds.h @@ -429,14 +429,15 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ /* I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x118000 -#define CONFIG_SYS_I2C2_OFFSET 0x118100 +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_FSL_I2C2_SPEED 100000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 + #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ #define I2C_MUX_PCA_ADDR_SEC 0x76 /* I2C bus multiplexer,secondary */ diff --git a/include/configs/taihu.h b/include/configs/taihu.h index ac8e57a93e..e8d191e7f9 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -122,9 +122,9 @@ * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_NOPROBES { 0x69 } /* avoid i2c probe hangup (why?) */ +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* avoid i2c probe hangup (?) */ #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */ diff --git a/include/configs/taishan.h b/include/configs/taishan.h index 6dbed7d2d8..3dbfc6ad1d 100644 --- a/include/configs/taishan.h +++ b/include/configs/taishan.h @@ -120,7 +120,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #undef CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 diff --git a/include/configs/tegra-common-post.h b/include/configs/tegra-common-post.h index 21ca4bbd44..a3242fe612 100644 --- a/include/configs/tegra-common-post.h +++ b/include/configs/tegra-common-post.h @@ -149,8 +149,8 @@ #endif /* remove I2C support */ -#ifdef CONFIG_TEGRA_I2C -#undef CONFIG_TEGRA_I2C +#ifdef CONFIG_SYS_I2C_TEGRA +#undef CONFIG_SYS_I2C_TEGRA #endif #ifdef CONFIG_CMD_I2C #undef CONFIG_CMD_I2C diff --git a/include/configs/top9000.h b/include/configs/top9000.h index ba5b6071d2..65dabde54f 100644 --- a/include/configs/top9000.h +++ b/include/configs/top9000.h @@ -185,11 +185,12 @@ #define CONFIG_CMD_USB /* I2C support must always be enabled */ -#define CONFIG_SOFT_I2C #define CONFIG_CMD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 400000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7F + #define I2C0_PORT AT91_PIO_PORTA #define SDA0_PIN 23 #define SCL0_PIN 24 diff --git a/include/configs/trats.h b/include/configs/trats.h index 465ade6f02..9b6aac96e6 100644 --- a/include/configs/trats.h +++ b/include/configs/trats.h @@ -259,10 +259,12 @@ #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_CACHELINE_SIZE 32 -#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 50000 +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE #define CONFIG_SOFT_I2C_READ_REPEATED_START #define CONFIG_SYS_I2C_INIT_BOARD -#define CONFIG_SYS_I2C_SPEED 50000 #define CONFIG_I2C_MULTI_BUS #define CONFIG_SOFT_I2C_MULTI_BUS #define CONFIG_SYS_MAX_I2C_BUS 15 diff --git a/include/configs/trimslice.h b/include/configs/trimslice.h index 9567cc6e96..8e03f6f4c4 100644 --- a/include/configs/trimslice.h +++ b/include/configs/trimslice.h @@ -38,12 +38,11 @@ #define CONFIG_CMD_SF /* I2C */ -#define CONFIG_TEGRA_I2C +#define CONFIG_SYS_I2C_TEGRA #define CONFIG_SYS_I2C_INIT_BOARD -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_MAX_I2C_BUS 4 #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C /* SD/MMC */ #define CONFIG_MMC diff --git a/include/configs/u8500_href.h b/include/configs/u8500_href.h index 8277f8d388..0c97ab1894 100644 --- a/include/configs/u8500_href.h +++ b/include/configs/u8500_href.h @@ -150,7 +150,6 @@ */ #define CONFIG_U8500_I2C #undef CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_SYS_I2C_SLAVE 0 /* slave addr of controller */ diff --git a/include/configs/uc100.h b/include/configs/uc100.h index 43acf26679..8bf7353bc1 100644 --- a/include/configs/uc100.h +++ b/include/configs/uc100.h @@ -448,13 +448,10 @@ */ /* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 93000 /* 93 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0xFE - -#ifdef CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE /* * Software (bit-bang) I2C driver configuration */ @@ -470,7 +467,6 @@ #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ else immr->im_cpm.cp_pbdat &= ~PB_SCL #define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SOFT_I2C */ /*----------------------------------------------------------------------- * I2C EEPROM (24C164) diff --git a/include/configs/utx8245.h b/include/configs/utx8245.h index 3088409271..bf044456ce 100644 --- a/include/configs/utx8245.h +++ b/include/configs/utx8245.h @@ -219,8 +219,7 @@ protect on ${u-boot_startaddr} ${u-boot_endaddr}" *------------------------------------------------------------------*/ #if 1 #define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 400000 #define CONFIG_SYS_I2C_SLAVE 0x7F #endif diff --git a/include/configs/vct.h b/include/configs/vct.h index 8258ccd815..85a6c11137 100644 --- a/include/configs/vct.h +++ b/include/configs/vct.h @@ -232,11 +232,10 @@ /* * I2C/EEPROM */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 83000 /* 83 kHz is supposed to work */ -#define CONFIG_SYS_I2C_SLAVE 0x7f +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED 83000 /* 83 kHz is supposed to work */ +#define CONFIG_SYS_I2C_SOFT_SLAVE 0x7f /* * Software (bit-bang) I2C driver configuration @@ -324,7 +323,7 @@ int vct_gpio_get(int pin); #undef CONFIG_CMD_USB #undef CONFIG_SMC911X -#undef CONFIG_SOFT_I2C +#undef CONFIG_SYS_I2C_SOFT #undef CONFIG_SOURCE #undef CONFIG_SYS_LONGHELP #undef CONFIG_TIMESTAMP diff --git a/include/configs/vf610twr.h b/include/configs/vf610twr.h index 223321c6d3..5a7a066377 100644 --- a/include/configs/vf610twr.h +++ b/include/configs/vf610twr.h @@ -68,6 +68,13 @@ #define CONFIG_PHYLIB #define CONFIG_PHY_MICREL +/* I2C Configs */ +#define CONFIG_CMD_I2C +#define CONFIG_HARD_I2C +#define CONFIG_I2C_MXC +#define CONFIG_SYS_I2C_BASE I2C0_BASE_ADDR +#define CONFIG_SYS_I2C_SPEED 100000 + #define CONFIG_BOOTDELAY 3 #define CONFIG_LOADADDR 0x82000000 diff --git a/include/configs/vl_ma2sc.h b/include/configs/vl_ma2sc.h index 817d36f17e..e171ae4c40 100644 --- a/include/configs/vl_ma2sc.h +++ b/include/configs/vl_ma2sc.h @@ -131,10 +131,12 @@ #define CONFIG_SYS_I2C_SLAVE 0 /* not used */ #ifndef CONFIG_HARD_I2C -#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SOFT_SPEED CONFIG_SYS_I2C_SPEED +#define CONFIG_SYS_I2C_SOFT_SLAVE CONFIG_SYS_I2C_SLAVE /* Software I2C driver configuration */ - #define I2C_DELAY udelay(2500000/CONFIG_SYS_I2C_SPEED) #define AT91_PIN_SDA (1<<4) /* AT91C_PIO_PB4 */ diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h index 0cd838e192..b450ab5e17 100644 --- a/include/configs/vme8349.h +++ b/include/configs/vme8349.h @@ -221,17 +221,15 @@ #define CONFIG_OF_STDOUT_VIA_ALIAS /* I2C */ -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_FSL_I2C -#define CONFIG_I2C_CMD_TREE -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */ -#define CONFIG_SYS_I2C1_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_OFFSET CONFIG_SYS_I2C1_OFFSET +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ #define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */ diff --git a/include/configs/walnut.h b/include/configs/walnut.h index e24295cf14..b23824bd0a 100644 --- a/include/configs/walnut.h +++ b/include/configs/walnut.h @@ -79,7 +79,7 @@ * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/whistler.h b/include/configs/whistler.h index ed3eda1f0f..d5c7e3bbd6 100644 --- a/include/configs/whistler.h +++ b/include/configs/whistler.h @@ -30,12 +30,11 @@ #define CONFIG_BOARD_EARLY_INIT_F /* I2C */ -#define CONFIG_TEGRA_I2C +#define CONFIG_SYS_I2C_TEGRA #define CONFIG_SYS_I2C_INIT_BOARD -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_SYS_MAX_I2C_BUS 4 #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_CMD_I2C +#define CONFIG_SYS_I2C /* SD/MMC */ #define CONFIG_MMC diff --git a/include/configs/xpedite1000.h b/include/configs/xpedite1000.h index 28af3cba5a..ea270509c1 100644 --- a/include/configs/xpedite1000.h +++ b/include/configs/xpedite1000.h @@ -129,11 +129,11 @@ extern void out32(unsigned int, unsigned long); /* * I2C */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7f -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7f /* I2C EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 diff --git a/include/configs/xpedite517x.h b/include/configs/xpedite517x.h index 51bdd095eb..97ce3eb542 100644 --- a/include/configs/xpedite517x.h +++ b/include/configs/xpedite517x.h @@ -242,13 +242,14 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 100000 /* M41T00 only supports 100 KHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 100000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 100000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* PEX8518 slave I2C interface */ #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 diff --git a/include/configs/xpedite520x.h b/include/configs/xpedite520x.h index c20935dfcf..372135a89f 100644 --- a/include/configs/xpedite520x.h +++ b/include/configs/xpedite520x.h @@ -204,13 +204,14 @@ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h index 6cf35f3105..31330eaa30 100644 --- a/include/configs/xpedite537x.h +++ b/include/configs/xpedite537x.h @@ -242,13 +242,15 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* PEX8518 slave I2C interface */ #define CONFIG_SYS_I2C_PEX8518_ADDR 0x70 diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h index 5a4125193a..340d4be4c6 100644 --- a/include/configs/xpedite550x.h +++ b/include/configs/xpedite550x.h @@ -234,13 +234,14 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C2_OFFSET 0x3100 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 /* I2C DS7505 temperature sensor */ #define CONFIG_DTT_LM75 diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index 2c1de321bb..4d3abf08bd 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -121,7 +121,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) diff --git a/include/configs/yucca.h b/include/configs/yucca.h index e3b0840ced..5d584fbad4 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -104,13 +104,13 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 #define IIC0_BOOTPROM_ADDR 0x50 #define IIC0_ALT_BOOTPROM_ADDR 0x54 /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_NOPROBES {0x50, 0x52, 0x53, 0x54} +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x50}, {0, 0x52}, {0, 0x53}, {0, 0x54} } /* #if defined(CONFIG_CMD_EEPROM) */ /* #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 */ /* I2C boot EEPROM */ diff --git a/include/configs/zeus.h b/include/configs/zeus.h index 04448d6261..386f9deb70 100644 --- a/include/configs/zeus.h +++ b/include/configs/zeus.h @@ -152,11 +152,11 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* these are for the ST M24C02 2kbit serial i2c eeprom */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ diff --git a/include/fdtdec.h b/include/fdtdec.h index f2ac13bee8..6bf83bf7c1 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -84,6 +84,7 @@ enum fdt_compat_id { COMPAT_MAXIM_98095_CODEC, /* MAX98095 Codec */ COMPAT_INFINEON_SLB9635_TPM, /* Infineon SLB9635 TPM */ COMPAT_INFINEON_SLB9645_TPM, /* Infineon SLB9645 TPM */ + COMPAT_SAMSUNG_EXYNOS5_I2C, /* Exynos5 High Speed I2C Controller */ COMPAT_COUNT, }; diff --git a/include/i2c.h b/include/i2c.h index bbea29b47e..d8674efe58 100644 --- a/include/i2c.h +++ b/include/i2c.h @@ -1,4 +1,8 @@ /* + * Copyright (C) 2009 Sergey Kubushyn + * Copyright (C) 2009 - 2013 Heiko Schocher + * Changes for multibus/multiadapter I2C support. + * * (C) Copyright 2001 * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com. * @@ -30,16 +34,14 @@ */ #define I2C_RXTX_LEN 128 /* maximum tx/rx buffer length */ -#ifdef CONFIG_I2C_MULTI_BUS -#define MAX_I2C_BUS 2 -#define I2C_MULTI_BUS 1 +#if !defined(CONFIG_SYS_I2C_MAX_HOPS) +/* no muxes used bus = i2c adapters */ +#define CONFIG_SYS_I2C_DIRECT_BUS 1 +#define CONFIG_SYS_I2C_MAX_HOPS 0 +#define CONFIG_SYS_NUM_I2C_BUSES ll_entry_count(struct i2c_adapter, i2c) #else -#define MAX_I2C_BUS 1 -#define I2C_MULTI_BUS 0 -#endif - -#if !defined(CONFIG_SYS_MAX_I2C_BUS) -#define CONFIG_SYS_MAX_I2C_BUS MAX_I2C_BUS +/* we use i2c muxes */ +#undef CONFIG_SYS_I2C_DIRECT_BUS #endif /* define the I2C bus number for RTC and DTT if not already done */ @@ -53,6 +55,88 @@ #define CONFIG_SYS_SPD_BUS_NUM 0 #endif +struct i2c_adapter { + void (*init)(struct i2c_adapter *adap, int speed, + int slaveaddr); + int (*probe)(struct i2c_adapter *adap, uint8_t chip); + int (*read)(struct i2c_adapter *adap, uint8_t chip, + uint addr, int alen, uint8_t *buffer, + int len); + int (*write)(struct i2c_adapter *adap, uint8_t chip, + uint addr, int alen, uint8_t *buffer, + int len); + uint (*set_bus_speed)(struct i2c_adapter *adap, + uint speed); + int speed; + int slaveaddr; + int init_done; + int hwadapnr; + char *name; +}; + +#define U_BOOT_I2C_MKENT_COMPLETE(_init, _probe, _read, _write, \ + _set_speed, _speed, _slaveaddr, _hwadapnr, _name) \ + { \ + .init = _init, \ + .probe = _probe, \ + .read = _read, \ + .write = _write, \ + .set_bus_speed = _set_speed, \ + .speed = _speed, \ + .slaveaddr = _slaveaddr, \ + .init_done = 0, \ + .hwadapnr = _hwadapnr, \ + .name = #_name \ +}; + +#define U_BOOT_I2C_ADAP_COMPLETE(_name, _init, _probe, _read, _write, \ + _set_speed, _speed, _slaveaddr, _hwadapnr) \ + ll_entry_declare(struct i2c_adapter, _name, i2c) = \ + U_BOOT_I2C_MKENT_COMPLETE(_init, _probe, _read, _write, \ + _set_speed, _speed, _slaveaddr, _hwadapnr, _name); + +struct i2c_adapter *i2c_get_adapter(int index); + +#ifndef CONFIG_SYS_I2C_DIRECT_BUS +struct i2c_mux { + int id; + char name[16]; +}; + +struct i2c_next_hop { + struct i2c_mux mux; + uint8_t chip; + uint8_t channel; +}; + +struct i2c_bus_hose { + int adapter; + struct i2c_next_hop next_hop[CONFIG_SYS_I2C_MAX_HOPS]; +}; +#define I2C_NULL_HOP {{-1, ""}, 0, 0} +extern struct i2c_bus_hose i2c_bus[]; + +#define I2C_ADAPTER(bus) i2c_bus[bus].adapter +#else +#define I2C_ADAPTER(bus) bus +#endif +#define I2C_BUS gd->cur_i2c_bus + +#define I2C_ADAP_NR(bus) i2c_get_adapter(I2C_ADAPTER(bus)) +#define I2C_ADAP I2C_ADAP_NR(gd->cur_i2c_bus) +#define I2C_ADAP_HWNR (I2C_ADAP->hwadapnr) + +#ifndef CONFIG_SYS_I2C_DIRECT_BUS +#define I2C_MUX_PCA9540_ID 1 +#define I2C_MUX_PCA9540 {I2C_MUX_PCA9540_ID, "PCA9540B"} +#define I2C_MUX_PCA9542_ID 2 +#define I2C_MUX_PCA9542 {I2C_MUX_PCA9542_ID, "PCA9542A"} +#define I2C_MUX_PCA9544_ID 3 +#define I2C_MUX_PCA9544 {I2C_MUX_PCA9544_ID, "PCA9544A"} +#define I2C_MUX_PCA9547_ID 4 +#define I2C_MUX_PCA9547 {I2C_MUX_PCA9547_ID, "PCA9547A"} +#endif + #ifndef I2C_SOFT_DECLARATIONS # if defined(CONFIG_MPC8260) # define I2C_SOFT_DECLARATIONS volatile ioport_t *iop = ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT); @@ -97,26 +181,103 @@ void i2c_init_board(void); void i2c_board_late_init(void); #endif -#if defined(CONFIG_I2C_MUX) +#ifdef CONFIG_SYS_I2C +/* + * i2c_get_bus_num: + * + * Returns index of currently active I2C bus. Zero-based. + */ +unsigned int i2c_get_bus_num(void); -typedef struct _mux { - uchar chip; - uchar channel; - char *name; - struct _mux *next; -} I2C_MUX; +/* + * i2c_set_bus_num: + * + * Change the active I2C bus. Subsequent read/write calls will + * go to this one. + * + * bus - bus index, zero based + * + * Returns: 0 on success, not 0 on failure + * + */ +int i2c_set_bus_num(unsigned int bus); -typedef struct _mux_device { - int busid; - I2C_MUX *mux; /* List of muxes, to reach the device */ - struct _mux_device *next; -} I2C_MUX_DEVICE; +/* + * i2c_init_all(): + * + * Initializes all I2C adapters in the system. All i2c_adap structures must + * be initialized beforehead with function pointers and data, including + * speed and slaveaddr. Returns 0 on success, non-0 on failure. + */ +void i2c_init_all(void); -I2C_MUX_DEVICE *i2c_mux_search_device(int id); -I2C_MUX_DEVICE *i2c_mux_ident_muxstring (uchar *buf); -int i2x_mux_select_mux(int bus); -int i2c_mux_ident_muxstring_f (uchar *buf); +/* + * Probe the given I2C chip address. Returns 0 if a chip responded, + * not 0 on failure. + */ +int i2c_probe(uint8_t chip); + +/* + * Read/Write interface: + * chip: I2C chip address, range 0..127 + * addr: Memory (register) address within the chip + * alen: Number of bytes to use for addr (typically 1, 2 for larger + * memories, 0 for register type devices with only one + * register) + * buffer: Where to read/write the data + * len: How many bytes to read/write + * + * Returns: 0 on success, not 0 on failure + */ +int i2c_read(uint8_t chip, unsigned int addr, int alen, + uint8_t *buffer, int len); + +int i2c_write(uint8_t chip, unsigned int addr, int alen, + uint8_t *buffer, int len); + +/* + * Utility routines to read/write registers. + */ +uint8_t i2c_reg_read(uint8_t addr, uint8_t reg); + +void i2c_reg_write(uint8_t addr, uint8_t reg, uint8_t val); + +/* + * i2c_set_bus_speed: + * + * Change the speed of the active I2C bus + * + * speed - bus speed in Hz + * + * Returns: new bus speed + * + */ +unsigned int i2c_set_bus_speed(unsigned int speed); + +/* + * i2c_get_bus_speed: + * + * Returns speed of currently active I2C bus in Hz + */ + +unsigned int i2c_get_bus_speed(void); + +/* + * i2c_reloc_fixup: + * + * Adjusts I2C pointers after U-Boot is relocated to DRAM + */ +void i2c_reloc_fixup(void); +#if defined(CONFIG_SYS_I2C_SOFT) +void i2c_soft_init(void); +void i2c_soft_active(void); +void i2c_soft_tristate(void); +int i2c_soft_read(void); +void i2c_soft_sda(int bit); +void i2c_soft_scl(int bit); +void i2c_soft_delay(void); #endif +#else /* * Probe the given I2C chip address. Returns 0 if a chip responded, @@ -219,6 +380,21 @@ int i2c_set_bus_speed(unsigned int); */ unsigned int i2c_get_bus_speed(void); +#endif /* CONFIG_SYS_I2C */ + +/* + * only for backwardcompatibility, should go away if we switched + * completely to new multibus support. + */ +#if defined(CONFIG_SYS_I2C) || defined(CONFIG_I2C_MULTI_BUS) +# if !defined(CONFIG_SYS_MAX_I2C_BUS) +# define CONFIG_SYS_MAX_I2C_BUS 2 +# endif +# define I2C_MULTI_BUS 0 +#else +# define CONFIG_SYS_MAX_I2C_BUS 1 +# define I2C_MULTI_BUS 0 +#endif /* NOTE: These two functions MUST be always_inline to avoid code growth! */ static inline unsigned int I2C_GET_BUS(void) __attribute__((always_inline)); diff --git a/lib/fdtdec.c b/lib/fdtdec.c index 5952450b96..dc358562d1 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -57,6 +57,7 @@ static const char * const compat_names[COMPAT_COUNT] = { COMPAT(MAXIM_98095_CODEC, "maxim,max98095-codec"), COMPAT(INFINEON_SLB9635_TPM, "infineon,slb9635-tpm"), COMPAT(INFINEON_SLB9645_TPM, "infineon,slb9645-tpm"), + COMPAT(SAMSUNG_EXYNOS5_I2C, "samsung,exynos5-hsi2c"), }; const char *fdtdec_get_compatible(enum fdt_compat_id id)