mx6cuboxi: Add HDMI output support

Add HDMI output using PLL5 as the source for the IPU clocks,
and accurate VESA timings.

These settings are based on the patch from Soeren Moch <smoch@web.de>
submitted for the tbs2910 mx6 based board.

It allows the display to work properly at 1024x768@60.

This should make the hdmi output signal compatible with most if not all
modern displays.

Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
This commit is contained in:
Fabio Estevam 2015-04-29 22:28:09 -03:00 committed by Stefano Babic
parent 8148b82449
commit f68a9c6b3d
2 changed files with 117 additions and 2 deletions

View File

@ -18,9 +18,11 @@
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/errno.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/video.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
@ -159,10 +161,107 @@ int board_eth_init(bd_t *bis)
return cpu_eth_init(bis);
}
#ifdef CONFIG_VIDEO_IPUV3
static void do_enable_hdmi(struct display_info_t const *dev)
{
imx_enable_hdmi_phy();
}
struct display_info_t const displays[] = {
{
.bus = -1,
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_hdmi,
.enable = do_enable_hdmi,
.mode = {
.name = "HDMI",
/* 1024x768@60Hz (VESA)*/
.refresh = 60,
.xres = 1024,
.yres = 768,
.pixclock = 15384,
.left_margin = 160,
.right_margin = 24,
.upper_margin = 29,
.lower_margin = 3,
.hsync_len = 136,
.vsync_len = 6,
.sync = FB_SYNC_EXT,
.vmode = FB_VMODE_NONINTERLACED
}
}
};
size_t display_count = ARRAY_SIZE(displays);
static int setup_display(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
int reg;
int timeout = 100000;
enable_ipu_clock();
imx_setup_hdmi();
/* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
reg = readl(&ccm->analog_pll_video);
reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
writel(reg, &ccm->analog_pll_video);
writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
writel(reg, &ccm->analog_pll_video);
while (timeout--)
if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
break;
if (timeout < 0) {
printf("Warning: video pll lock timeout!\n");
return -ETIMEDOUT;
}
reg = readl(&ccm->analog_pll_video);
reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
writel(reg, &ccm->analog_pll_video);
/* gate ipu1_di0_clk */
clrbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
/* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */
reg = readl(&ccm->chsccdr);
reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
(6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
(0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &ccm->chsccdr);
/* enable ipu1_di0_clk */
setbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
return 0;
}
#endif /* CONFIG_VIDEO_IPUV3 */
int board_early_init_f(void)
{
int ret = 0;
setup_iomux_uart();
return 0;
#ifdef CONFIG_VIDEO_IPUV3
ret = setup_display();
#endif
return ret;
}
int board_init(void)

View File

@ -27,7 +27,7 @@
#define CONFIG_IMX6_THERMAL
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_SYS_MALLOC_LEN (2 * SZ_1M)
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_MXC_GPIO
@ -66,6 +66,22 @@
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
/* Framebuffer */
#define CONFIG_VIDEO
#define CONFIG_VIDEO_IPUV3
#define CONFIG_IPUV3_CLK 260000000
#define CONFIG_CFB_CONSOLE
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
#define CONFIG_SYS_NO_FLASH
/* Command definition */