When pressing the reset button on boot the system will enter the
recovery mode, this is done by setting a preboot command. Inside the
preboot command we will sleep and then check if the button is still
pressed, then tftp will be used to download the image and flash it. If
something fails after the DHCP state the network console will be
enabled.
The only ARM/kernel visible change is the change of the EEPROM. U-Boot
sadly does not support to select EEPROM with different page sizes and
address length. This is why we need to patch the common epprom code.
Introduce a new command to allow dynamic configuration of the EEPROM,
move the eeprom parameters into variables and change the code. This sadly
copies the SPI_X code as well. The address creation could be moved to
a different variable.
This code has been tested on RevC and RevD hardware and an IP address
could be obtained in both cases.
To make bootm sub-command feature working on archs with CONFIG_NEEDS_MANUAL_RELOC,
the name pointers in the sub-command table need to be relocated.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Some boards want to report more than just memory size. For example, it
might be useful to display the memory type (DDR2, DDR3) or manufacturer.
Add a weak function to support this requirement, accessed through a new
'meminfo' command.
Any example of the DRAM: output is below, just for illustration:
SMDK5250 # meminfo
DRAM: 2 GiB Elpida DDR3 @ 800MHz
Signed-off-by: Simon Glass <sjg@chromium.org>
Since U-Boot runs from coreboot on x86, the Coreboot version is an
important part of the boot state. This version information is
available in the coreboot tables, so print it when the 'version'
command is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make setexpr accept a 2 parameter variant that will simply load a value
into a variable. This is useful for loading a value from memory.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
It is useful to have a basic SPI flash test, which tests that the SPI chip,
the SPI bus and the driver are behaving.
This test erases part of the flash, writes data and reads it back as a
sanity check that all is well.
Use CONFIG_SF_TEST to enable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Output a progress update only at most 10 times per second, to avoid
saturating (and waiting on) the console. Make the summary line
to fit on a single line. Make sure that cursor sits at the end of
each update line instead of the beginning.
Sample output:
SF: Detected W25Q32 with page size 4 KiB, total 4 MiB
Update SPI
1331200 bytes written, 2863104 bytes skipped in 21.912s, speed 199728 B/s
time: 21.919 seconds, 21919 ticks
Skipping verify
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: James Miller <jamesmiller@chromium.org>
Signed-off-by: Taylor Hutt <thutt@chromium.org>
[trini: Drop 'const' from bytes_per_second()]
Signed-off-by: Tom Rini <trini@ti.com>
When a USB card reader is empty, it will return "Not Ready - medium not
present" as Key Code Qualifier. In that situation, it's useless waiting
for the full timeout since the result won't change until the user
inserts a card.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
If probe of a newly connected device fails for some reason, clean up
the allocated entry in usb_dev array.
Signed-off-by: Milind Choudhary <milindc@codeaurora.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The current logic reads the port status just once after usb_hub_power_on and
expects the portstatus and portchange to report the connection status
immediately and correctly.
Few pen drives are not able to report both of them immediately ie. those pens
report the connection change but not the connected state after the first read.
This opportunity once lost is gone for ever because the u-boot, unlike linux or
any other OS, works in polling mode.
This patch modifies the logic to read the port status continuously until the
portstatus and portchange both report a connection change as well as a connected
state or no connection change and no connection. This logic is placed in a
timeout of 10 sec. At the end of it, the pen drive would have either reported a
ONE or a ZERO in bit 1 of portstatus as well as portchange.
It enhances the set of pen drives which can eventually be detected by u-boot
Note: This 10 second timeout is based purely on several experiments done with
the broken pen drives
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Use the variable access flags to implement the protection for ethaddr
and serial# instead of hard-coding them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Similar to the env callback command, this will show details about the
options available, the static list, and the currently active variables.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address. Call
env_acl_validate_setenv_params() from setenv() in fw_env.c.
If the entry is not found in the env .flags, then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environment distracting you.
Need to build in _ctype for isdigit for Linux.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address.
If the entry is not found in the env ".flags", then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environment distracting you.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The silent variable now updates the global data flag anytime it is
changed as well as after the env relocation (in case its value is
different from the default env in such cases as NAND env)
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The callbacks can be bound, but are otherwise invisible. Add a command
to show what callbacks are available.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
!!! fix callback command
Add support for per-variable callbacks to the "hashtable" functions.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
!!!fix comment in callback
When printing all variables with env print, don't print variables that
begin with '.'. If env print is called with a '-a' switch, then
include variables that begin with '.' (just like the ls command).
Variables printed explicitly will be printed even without the -a.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Move the read of the old value to inside the check function. In some
cases it can be avoided all together and at the least the code is only
called from one place.
Also name the function and the callback to more clearly describe what
it does.
Pass the ENTRY instead of just the name for direct access to the whole
data structure.
Pass an enum to the callback that specifies the operation being approved.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use a flag in hsearch_r for insert mode passed from import to allow the
behavior be different based on use.
Now that "do_check" is called for all imports, ensure console init is
complete before updating the console on relocation import
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
New command - "gpt" is supported. It restores the GPT partition table.
It looks into the given environment variable for partitions definition.
It can be enabled at target configuration file with CONFIG_CMD_GPT.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Do not compile in FDT related code, when it is not supported.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add a simple command to stress-test a TPM (Trusted Platform Module).
Signed-off-by: Luigi Semenzato <semenzato@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The CONFIG_SYS_CONSOLE_INFO_QUIET option should suppress the console
information, but allow boards to display it later if required. Adjust
the code to support this.
This is used to avoid printing the information while the LCD display
is not ready, since it only becomes ready when stdio init is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function can be used for LCDs as well as monitors.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a single command to read the EDID information over I2C.
For example:
SMDK5250 # i2c dev 7
Setting bus to 7
SMDK5250 # i2c edid 50
EDID version: 1.4
Product ID code: 305c
Manufacturer: AUO
Serial number: 00000000
Manufactured in week: 0 year: 2011
Video input definition: digital signal, voltage level 0, blank to black
Monitor is non-RGB
Maximum visible display size: 26 cm x 14 cm
Power management features: no active off, no suspend, no standby
Estabilished timings:
Standard timings:
1366x768 60 Hz (detailed)
1366x768 60 Hz (detailed)
Monitor ID: 2VD2K.B116XW
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This implements a library for accessing EDID data from an LCD panel.
This is used to obtain information about the panel such as its
resolution and type.
This is a tidied-up version of the original code pulled from
https://github.com/ynezz/u-boot-edid.
The changes we made are:
- removed bit fields in the struct;
- removed endianness cases in the struct;
- fixed some wrong definitions;
- fixed to fit 80 columns;
- fixed some code styles.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This new command supports hashing SHA1 and SHA256. It could be extended
to others such as MD5 and the CRC algorithms. The syntax is modeled on
those:
hash <algorithm> <address> <length> [*<dest_addr> | <dest_envvar>]
to calculate a hash, and:
hash -v <algorithm> <address> <length> [*<verify_addr> | <verify_envvar>]
to verify a hash.
Use CONFIG_CMD_HASH to enable the command, CONFIG_SHA1 to enable SHA1 and
CONFIG_SHA256 to enable SHA256.
The existing sha1sum command remains.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a SHA1 command and want to add a SHA256 command also. Instead of
duplicating the code, create a generic hash API which can process
commands for different algorithms.
Signed-off-by: Simon Glass <sjg@chromium.org>
The name is already copied when we memcpy() the whole structure.
This is because struct stdio_dev has this field:
char name[16]; /* Device name */
So the data is inline, rather than being a pointer.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes data is on a block device and within a partition, but not in a
particular filesystem.
This commands permits reading raw data from a partition.
Signed-off-by: Kenneth Waters <kwaters@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Gettime returns the current timer value. If CONFIG_SYS_HZ is defined
then the timer value is also converted to seconds.
Tegra20 (SeaBoard) # gettime
Timer val: 7754
Seconds : 7
Remainder : 754
sys_hz = 1000
There has been some discussion about whether this is useful enough to
be included in U-Boot. The following boards do not have CONFIG_SYS_HZ
defined:
M52277EVB
M52277EVB_stmicro
M53017EVB
M54418TWR
M54418TWR_nand_mii
M54418TWR_nand_rmii
M54418TWR_nand_rmii_lowfreq
M54418TWR_serial_mii
M54418TWR_serial_rmii
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Holger Hans Peter Freyther
Tom Rini
Daniel Schwierzeck
Simon Glass
Stefan Reinauer
Joe Hershberger
James Miller
Allen Martin
Vincent Palatin
Milind Choudhary
Vipin Kumar
Piotr Wilczek
Łukasz Majewski
Luigi Semenzato
Vadim Bendebury
Tom Wai-Hong Tam
Kenneth Waters
Anton Staaf