This driver implements the HW WATCHDOG functions. Which needs
to set CONFIG_HW_WATCHDOG to use them. This is disabled by default for
mx7ulp.
Use watchdog for reset cpu. Implement this in the driver.
Need to define CONFIG_ULP_WATCHDOG to build it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Currently the driver asserts WDOG_B by clearing WCR_WDA bit when
enabling the watchdog. Do not clear WCR_WDA.
Signed-off-by: Ross Parker <rossjparker@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
This allows to overwrite reset_cpu function in case a board level
reset is preferred (e.g. through PMIC).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The problem is that timeout bits in WCR register were leaved unchanged.
So previously set timeout value was applied and therefore 'reset'
command takes any value up to two minutes, depending on previous
watchdog settings, instead of minimal 0.5 seconds.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Since commit 623d96e89aca6("imx: wdog: correct wcr register settings")
issuing a 'reset' command causes the system to hang.
Unlike i.MX and Vybrid, the watchdog controller on LS102x is big-endian.
This means that the watchdog on LS1021 has been working by accident as
it does not use the big-endian accessors in drivers/watchdog/imx_watchdog.c.
Commit 623d96e89aca6("imx: wdog: correct wcr register settings") only
revelead the endianness problem on LS102x.
In order to fix the reset hang, introduce a reset_cpu() implementation that
is specific for ls102x, which accesses the watchdog WCR register in big-endian
format. All that is required to reset LS102x is to clear the SRS bit.
This approach is a temporary workaround to avoid a regression for LS102x
in the 2015.10 release. The proper fix is to make the watchdog driver
endian-aware, so that it can work for i.MX, Vybrid and LS102x.
Reported-by: Sinan Akman <sinan@writeme.com>
Tested-by: Sinan Akman <sinan@writeme.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Create fsl_wdog.h to store the watchdog registers and bit fields.
This can be useful when accesses to the watchdog block are made from other
parts, such as arch/arm/ cpu code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We should not simple use "writew(WCR_WDE, &wdog->wcr)" to set
wcr, since this will override bits set before reset_cpu.
Use clrsetbits_le16 instead of writew to fix this issue.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Add imx-common cpu support for imx7d SoC
- Update reset_cause for imx7d
- Enable watchdog driver built for imx7d
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
with WCR_WDW set, the watchdog won't trigger if we bootet linux and idle
around while the watchdog is not triggered. It seems the timer makes
progress very slowly if at all. I managed to remain 20minutes alive
while the timeout was set to 60secs. It reboots within 60secs if I start
a busyloop in userland (something like "while (1) { }").
While I don't see a reason why the WDT should not be running while the
CPU is in idle, I'm dropping this bit.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chan-Taek Park <c-park@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.
Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
get_sclk() was not defined in bfin_wdt.c, include the corresponding header.
Cc: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Vasili Galka <vvv444@gmail.com>
To add the DesignWare watchdog driver support. It required
information such as register base address and clock info from
configuration header file within include/configs folder.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
Currently the driver clears WCR_SRS bit when enabling
the watchdog and this causes a software reset. Do not
clear WCR_SRS.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The patch:
"blackfin: Move blackfin watchdog driver out of the blackfin arch folder."
(sha1: e9a389a184)
changed hw_watchdog_init() prototype which didn't match
with Microblaze one.
This patch fixes the driver and Microblaze initialization.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
1. Move header to include/faraday
2. Fix include path in ftwdt010_wdt.c
3. Fix function prototype and declaration to
- ftwdt010_wdt_settimeout
- ftwdt010_wdt_reset
- ftwdt010_wdt_disable
4. Add "#if definde (CONFIG_HW_WATCHDOG)" let user have flexibilty
to choose which better to his product.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Faraday ftwdt010 watchdog is an architecture independant
watchdog. It is usually used in SoC chip design.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Ye Li
Ross Parker
Stefan Agner
Andrey Skvortsov
Fabio Estevam
Peng Fan
Adrian Alonso
Sebastian Siewior
Masahiro Yamada
Heiko Schocher
Wang Huan
Vasili Galka
Chin Liang See
Albert ARIBAUD
Anatolij Gustschin
Michal Simek
Wolfgang Denk
Sonic Zhang
Troy Kisky
Marek Vasut
Reinhard Meyer
Macpaul Lin
Sebastien Carlier
Achim Ehrlich
Jean-Christophe PLAGNIOL-VILLARD