Commit Graph

171 Commits

Author SHA1 Message Date
Jon Hunter 2a309f33de omap5912-osk: Fix device initialisation
In the current u-boot, the device pin multiplexing and clock
initialisation needs to be early during the boot process and before
board_init() is called. U-boot is currently crashing on this board
because this is not being done early enough. Therefore, add a s_init()
function for the omap5912-osk board to do this.

Also fix the stack pointer so that it is pointing to the end of the
internal RAM and not the beginning as this was also causing the device
to crash.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-10 16:03:01 -04:00
Jon Hunter 5faba1eac6 omap5912-osk: Fix booting from NOR flash
The omap5912-osk board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash at address
0x00000000.

The omap5912-osk board only has 32MB of RAM and so fix the comment
in the omap5912-osk config.mk file as well.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-10 16:03:01 -04:00
Jon Hunter c8b30b858f omap5912-osk: Fix DRAM initialisation
The size of the DRAM for the omap5912-osk board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap5912-osk board and setup the
DRAM size there.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-10 16:03:01 -04:00
Tom Rini b996a3e9a8 am335x: Update timings for the beaglebone again
After further testing we can run DDR at 400MHz so update the timings
again.

Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
2013-04-10 10:04:40 -04:00
SRICHARAN R 2c2a9f3a1f ARM: OMAP5: Rename omap5_evm to omap5_uevm
The omap5-uevm is the reference board name for OMAP5 soc
based platform. So rename it accordingly.

Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
2013-04-08 11:29:05 -04:00
Hunter, Jon 47f58a7357 omap2420-h4: Fix booting from NOR flash
The omap2420-h4 board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash. Please note
that OMAP maps the NOR flash to address 0x08000000 by default and so
use this as the default address for the NOR flash.

Also remove legacy code that attempts to calculate where in flash the
sdata structure, that holds the memory interface configuration data,
is located. By changing the default linker location for code to flash
this is no longer necessary.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-08 11:29:05 -04:00
Hunter, Jon 335d9394c9 omap2420-h4: Fix DRAM initialisation
The size of the DRAM for the omap2420-h4 board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap2420-h4 board and setup the
DRAM size there.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-08 11:29:05 -04:00
Tom Rini c7ba18ad4b am335x_evm: Add better timings for the new BeagleBoard DDR3 part
Tested-by: Rao Bodapati <rao@circuitco.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:12 -04:00
Matt Porter ea7b96b6aa ti814x_evm: add ti814x evm board support
Add TI814X EVM board directory, config file, and MAINTAINERS
entry. Enable build.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Adapt to recent omap_hsmmc requirements, Matt re-tested]
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:12 -04:00
Matt Porter 3ba65f97cb am33xx: refactor emif4/ddr to support multiple EMIF instances
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Matt Porter 81df2bab46 am33xx: convert defines from am33xx-specific to generic names
Eliminate AM33xx specific names to prepare for TI814x support
within AM33xx-land.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:11 -04:00
Vaibhav Hiremath 59dcf970d1 am335x: Enable DDR PHY dynamic power down bit for DDR3 boards
Enable DDR PHY dynamic power down bit, which enables
powering down the IO receiver when not performing read.

This also helps in reducing overall power consumption in
low power states (suspend/standby).

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:05 -04:00
Lokesh Vutla 687054a7e0 arm: dra7xx: Add board files for DRA7XX socs
Adding new board files for DRA7XX socs.
The pad registers layout is changed completely from OMAP5
So introducing the new structure here and also adding the
minimal data.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Adapt omap_mmc_init call for last 2 params]
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11 11:39:30 -04:00
Nikita Kiryanov bcc6cc9b37 omap3: allow dynamic selection of gfx_format
Currently, omap3_dss_panel_config() sets gfx_format to a value that is hardcoded
in the code. This forces anyone who wants to use a different gfx_format to make
adjustments after calling omap3_dss_panel_config(). This could be avoided if the
value of gfx_format were parameterized as input for omap3_dss_panel_config().

Make gfx_format a field in struct panel_config, and update existing structs to
set this field to the value that was originally hard coded.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08 16:41:13 -05:00
Nikita Kiryanov e3913f56a2 omap_hsmmc: add driver check for write protection
Add check for write protection in omap mmc driver.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-08 16:41:13 -05:00
Nikita Kiryanov e874d5b001 omap_hsmmc: implement driver check for card detection
Implement driver check for card detection.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2013-03-08 16:41:13 -05:00
Tom Rini 98bc1228c8 am335x_evm: Add am335x_evm_usbspl build target
We add USB (RNDIS gadget) SPL support as a separate target.  We need to
pull out YMODEM support in order to be a small enough target binary.

Signed-off-by: Tom Rini <trini@ti.com>
2013-03-08 16:41:12 -05:00
Ilya Yanok c0e66793c4 am335x_evm: enable support for booting via USB
This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now.  This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.

The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-02-18 13:49:16 -05:00
robertcnelson@gmail.com 8a1f2dc081 beagle: expansion boards: add LSR COM6L adapter
http://www.lsr.com/wireless-products/com6l

The eeprom on this expansion board requires 16bit addressing.

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
2013-02-18 13:48:04 -05:00
robertcnelson@gmail.com ff229ecf8b beagle: expansion boards: retry i2c_read with 16bit addressing
Some expansion boards now ship with at24 eeproms that need to communicate
via 16bit addressing.

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
2013-02-18 13:48:04 -05:00
Tom Rini 1634e96918 am335x_evm: Fix CPSW ethernet on GP EVM and EVM-SK
In commit cfd4ff6 we implemented part of advisory 1.0.10 (internal delay
for RGMII mode not supported).  This in turn however requires that we
set the tx clock delay feature in the PHY itself.

Signed-off-by: Tom Rini <trini@ti.com>
2013-02-12 14:59:23 -05:00
Jeff Lance 13526f7157 Add DDR3 support for AM335x-EVM (Version 1.5A)
AM335x EVM 1.5A uses Micron MT41J512M8RH-125 SDRAM 4Gb (512Mx8) as the
DDR3 chip.

[Hebbar Gururaja <gururaja.hebbar@ti.com>]
	- Resolve merge conflict while rebasing. File structure is
	  changed in the mainline. So re-arrange the code accordingly.
	- Update commit message to reflect the DDR3 part number

Signed-off-by: Jeff Lance <j-lance1@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
2013-02-07 10:36:26 -05:00
Lars Poeschel 3ec36b34fe am335x: display msg when reading MAC from efuse
When ethaddr is not set in environment the MAC address is read
from efuse. The message was only printed in debug case, but this
message could be of interest for the ordinary user, so printf it.

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
2013-02-07 10:36:26 -05:00
Albert ARIBAUD 79f3877794 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
This required manual merging drivers/mtd/nand/Makefile
and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
2013-01-08 13:15:45 +01:00
Yegor Yefremov cfd4ff6f0f am335x: disable internal delay for RGMII mode
According to errata the AM335x device does not support internal delay
mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2012-12-10 08:56:38 -07:00
Peter Barada 8c4445d266 Pass sdrc timing values through board_sdrc_timings structure
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings.  This saves about
90 bytes of space in SPL.

Signed-off-by: Peter Barada <peter.barada@logicpd.com>
2012-12-10 08:54:02 -07:00
Ilya Yanok 98b5c26943 am335x_evm: enable NAND support
Enable NAND support for AM335X boards.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10 08:54:02 -07:00
Ilya Yanok 70fb65b093 am335x_evm: add nand pinmux definition
Add NAND pins mux settings for AM335X devices. Enable NAND pins
for AM335X EVM board.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10 08:54:01 -07:00
Ilya Yanok c642b151f3 omap3_beagle: add musb-new init
Add initialization for new MUSB framework.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:08 +01:00
Ilya Yanok d2aa1154b9 am335x_evm: enable both musb gadget and host
Enable musb gadget in Ethernet mode on port 0 and
musb host on port1.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:07 +01:00
Tom Rini 6acc7c3cbc Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-11-05 07:42:00 -07:00
Albert ARIBAUD a42c87f9d8 Merge remote-tracking branch 'u-boot-ti/master' 2012-11-03 10:05:22 +01:00
Tom Rini 044fc14bcb am335x_evm: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this.  It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.

Signed-off-by: Tom Rini <trini@ti.com>
2012-11-02 15:14:28 -07:00
Matthias Fuchs a956bdcb3f am335x: add initial AM335x IDK board support
This patch extends the am335x_evm board for the AM335x IDK.

The IDK board uses MII for the ethernet phy (same as
Beaglebone board) and MMC0 for storage (but without
card detect line).

The IDK uses UART3 for console. So u-boot must be build
with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for
the am335x_evm_uart3 board configuration as introduced
by Andrew Bradfords recent patch series "am33xx: Enable
UART {1,2,3,4,5}...". When using the IDK with console on UART0,
those patches are not required. In this case the board
slightly needs to be modified.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2012-11-02 10:04:04 -07:00
Koen Kooi 9cd7b4cdca am335x: add mux config for DDR3 version of beaglebone
This fixes the following boothang in SPL:

	Unknown board, cannot configure pinmux.### ERROR ### Please RESET the board ###

Future commits will add pinmuxes for more on-board peripherals.

Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
2012-10-30 15:28:44 -07:00
Albert ARIBAUD c68436fa42 Merge remote-tracking branch 'u-boot-ti/master' 2012-10-26 07:00:28 +02:00
Andrew Bradford 6422b70bd5 am33xx: Enable UART{1,2,3,4,5} pin-mux
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.

Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
2012-10-25 14:54:50 -07:00
Peter Korsgaard c7d35bef25 am33xx/ddr_defs.h: rename DDR2/DDR3 defines to their actual part numbers
So other parts can be added.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25 11:31:38 -07:00
Peter Korsgaard c00f69dbcd am33xx: support board specific ddr settings
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:38 -07:00
Peter Korsgaard 7f26a5a26f am33xx: move generic parts of pinmux handling out from board/ti/am335x
So they are available for other boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-25 11:31:37 -07:00
Peter Korsgaard e363426e99 am33xx: move ti i2c baseboard header handling to board/ti/am335x/
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-25 11:31:36 -07:00
Ashok 860bde3fee omap2424:Rename CONFIG_DRIVER_LAN91C96 to CONFIG_LAN91C96 as CONFIG_DRIVER_LAN91C96 is obsolete.
Rename CONFIG_DRIVER_LAN91C96 to CONFIG_LAN91C9 as
CONFIG_DRIVER_LAN91C96 is obsolete.

Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com>
2012-10-22 08:31:57 -07:00
Lucas Stach 676ae068d9 usb: ehci: rework to take advantage of new lowlevel interface
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.

NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2012-10-15 11:54:00 -07:00
Albert ARIBAUD b823fd9ba5 ARM: prevent misaligned array inits
Under option -munaligned-access, gcc can perform local char
or 16-bit array initializations using misaligned native
accesses which will throw a data abort exception. Fix files
where these array initializations were unneeded, and for
files known to contain such initializations, enforce gcc
option -mno-unaligned-access.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Switch to usign call cc-option for -mno-unaligned-access as
Albert had done previously as that's really correct]
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15 11:53:07 -07:00
Ilya Yanok 7ac2fe2da2 OMAP: networking support for SPL
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-01 10:02:14 -07:00
Tom Rini a4a99fffd8 am335x evm: Enable support for spi0
Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:19 +02:00
Tom Rini 6bfca5031b am335x evm: Enable MMC1 pinmux
MMC1 is available in profile 2 on the GP EVM and is exposed on the
expansion header on beaglebone.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Tom Rini 036fd65a8c am335x evm: Initial support for AM335x GP EVM Profiles
The AM335x GP EVM can have one of 8 different profiles selected.  Each
profile has a different set of peripherals and requires different pinmux
configurations that conflict with other profiles.  i2c1 is an example of
a conflicted mux currently.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:18 +02:00
Tom Rini db7dd8109c am33xx: Rework pinmux functions
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
  - Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00
Tom Rini 65d750be59 am33xx: Add support for TI AM335x StarterKit EVM
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
  config_ddr with.
- Both of the above require filling in the header structure early, move
  it into the data section.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-01 14:58:13 +02:00