Commit graph

9 commits

Author SHA1 Message Date
Steve Sakoman
a06e1629f4 ARMV7: OMAP: Overo: Autodetect presence/absence of transceiver on mmc2
An upcoming version of Overo uses a Wifi/BT module with 1.8V signaling,
eliminating the need for an external transceiver to handle the level
shifting.  This patch detects whether an external transceiver is present
and adjusts the pinmux settings as appropriate.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-08 14:51:45 -04:00
Steve Sakoman
ba9a11e4ea ARMV7: OMAP: Configure Overo's second network chip
Confiures GPMC timings for both chips and also configures pinmux
for GPIO_65, which is used as the interrupt signal for the second chip

Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-08 14:50:47 -04:00
Steve Sakoman
c2d5b34120 ARMV7: OMAP: Add board revision detection for Overo
The latest Overo COM modules encode their revision number on
GPIOs 115, 113, and 112.  All boards to date have no pullups on these pins
and hence appear as revision 0.

This patch reads and prints the revision information.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-08 14:50:38 -04:00
Steve Sakoman
9314961329 ARMV7: OMAP: Enable input driver on Overo's MMC1_CLK and MMC3_CLK pinmux setup
This patch modifies the pinmux setup for MMC1_CLK and MMC3_CLK to enable
the input driver.  MMC2_CLK was already properly configured.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-08 14:50:27 -04:00
Scott Ellis
093d6018cf Overo GPMC registers
Use appropriate GPMC timings for the LAN9221 controller on the
Gumstix Overo expansion boards not the values in arch-omap3/mem.h
which are for a different ethernet controller.

Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-02-12 12:31:53 -06:00
Grazvydas Ignotas
ead39d7aa3 TWL4030: make LEDs selectable for twl4030_led_init()
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().

Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2010-01-04 08:48:15 -06:00
Olof Johansson
df3826262c TI: OMAP3: Overo Tobi ethernet support
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.

This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.

Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-10-13 06:17:38 -05:00
Olof Johansson
fc9165fdb3 OMAP3: Clean up whitespace in mux configs
Switch from space-based indentation to tab-based in mux configs, as pointed
out by WD at:

http://lists.denx.de/pipermail/u-boot/2009-September/061241.html

Nothing but whitespace changes in this patch (diff -w gives no output).

Signed-off-by: Olof Johansson <olof@lixom.net>
2009-10-13 06:17:36 -05:00
Jean-Christophe PLAGNIOL-VILLARD
127f9ae575 omap3: move the other boards to board/
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-09-05 01:33:12 +02:00