Enabled clocks for the second dwc3 controller and second USB PHY present in
DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SYS_BOOT-based fallback shouldn't only check for one of the conditions of
use and then let the switch/case handle each boot device without enforcing the
conditions for each type of boot device again.
For instance, this behaviour would trigger the fallback for UART when
BOOT_DEVICE_UART is defined, CONFIG_SPL_YMODEM_SUPPORT is enabled (which should
be a show-stopper) and e.g. BOOT_DEVICE_USB is enabled and not
CONFIG_SPL_USB_SUPPORT.
Separating the logic for USB and UART solves this.
In addition, this adds support for more peripheral devices (USBETH and CPGMAC)
to the fallback mechanism. Note that the USBETH boot device should always be
different from the USB boot device (each should match a different bootrom
handoff case).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The designware ethernet driver supports d-cache now. So there is nothing
stopping us now to enable the caches completely on SPEAr.
Tested on SPEAr600 x600 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
The SPL implementation for SPEAr600 is older than the common SPL
infrastructure. This patch now moves the SPEAr600 SPL over to the
common SPL code.
Tested on the only SPEAr board that currently uses SPL in mainline
U-Boot, the x600.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
ARM supported speeds and init value of core_pll for SDP1200
are programmed wrong as part for the device speed cleanups.
Fixing it here.
Thanks to "Vitaly Andrianov <vitalya@ti.com>" for bisecting this issue
Fixes: c37ed9f11b61 ("ARM: keystone2: Fix dev and arm speed detection")
Tested-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MLO(NAND/MMC boot image), is used for all the ks2 platforms.
Enabling it in config.mk so that these images will be automatically
built upon calling make. u-boot-spi.gph is already the build target,
so not including here.
Reported-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
NAND boot mode, ROM expects an image with a gp header in the
beginning and an 8bytes filled with zeros at the end. The same is
true for SD boot on K2G platforms but the file name should be MLO.
Renaming u-boot-nand.gph to MLO, so that same image can be used for
NAND and SD boots. And also not including all the u-boot only images
under CONFIG_SPL_BUILD.
Reported-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Keystone has build rules introduced by commit ef509b9063 ("k2hk: add
support for k2hk SOC and EVM") and commit 0e7f2dbac6 ("keystone: add
support for NAND gpheader image").
These are not reused by other platforms for the build, hence there is no
clear benefit is maintaining them in the generic makefile as a build
target. move these to the keystone specific make option
Original idea of using config.mk by Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.
Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.
NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for detection of ES2.0 version of DRA7 family of
processors. ES2.0 is an incremental revision with various fixes
including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
[ravibabu@ti.com: posted internal for an older bootloader]
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In order to make a pci uart device node to be properly bound to its
driver, we need make sure its parent node has a compatible string
which matches a driver that scans all of its child device nodes in
the device tree.
Change all pci bridge nodes under root pci node to use "pci-bridge"
compatible driver, as well as corresponding <reg> properties to
indicate its devfn. At last, adding "u-boot,dm-pre-reloc" to each
of these nodes for driver model to initialize them before relocation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far we only enabled one legacy serial port on the SMSC LPC47m
superio chipset on Intel Crown Bay board. As the board also has
dual PS/2 ports routed out, enable the keyboard controller which
is i8042 compatible so that we can use PS/2 keyboard and mouse.
In order to make PS/2 keyboard work with the VGA console, remove
CONFIG_VGA_AS_SINGLE_DEVICE. To boot Linux kernel with PIC mode
using PIRQ routing table, adjust the mask in the device tree to
reserve irq12 which is used by PS/2 mouse.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These GPIOs are accessible on the pin header. Add pinctrl settings for them
so that we they can be adjusted using the 'gpio' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
The DSDT table contains a bytecode that is executed by a driver in the kernel.
Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Tested with QEMU '-M q35'
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This patch mainly adds ACPI support to QEMU.
Verified by booting Linux kernel on QEMU Q35.
Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Minor whitespace fixes and dropped mention of i440FX in commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement write_acpi_table() to create a minimal working ACPI table.
This includes writing FACS, XSDT, RSDP, FADT, MCFG, MADT, DSDT & SSDT
ACPI table entries.
Use a Kconfig option GENERATE_ACPI_TABLE to tell U-Boot whether we need
actually write the APCI table just like we did for PIRQ routing, MP table
and SFI tables. With ACPI table existence, linux kernel gets control of
power management, thermal management, configuration management and
monitoring in hardware.
Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tidied up whitespace and aligned some tabs:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an api to enable and configure the integrated keyboard controller
on SMSC LPC47m superio chipset. It also adds several macros to help
future extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
It turns out that calling fsp_init_phase_pci() in arch_misc_init()
is subject to break pci device drivers as with driver model, when
the bus enumeration happens is not deterministic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
With dm pci conversion, pci config read/write in unprotect_spi_flash()
silently fails as at that time dm pci is not ready and bus enumeration
is not done yet. Actually we don't need to do this in that early phase,
hence we delay this call to arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add some comments in start.S for the fact that with FSP U-Boot
actually enters the code twice. Also change to use fsp_init()
and fsp_continue for accuracy.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
After fsp_init() returns, the stack has already been switched to a
place within system memory as defined by CONFIG_FSP_TEMP_RAM_ADDR.
Enlarge the size of malloc() pool before relocation since we have
plenty of memory now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel FSP has the capability to walk through the microcode blocks
which are passed as the TempRamInit() parameter from U-Boot and
finds the most appropriate microcode which is suitable for the cpu
on which it is running. Now we've seen several steppings for Intel
BayTrail series processors, adding those microcodes to the Intel
BayleyBay and MinnowMax board device tree files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adds the microcode blob for BayTrail-I D0 stepping,
CPUID signature 30679h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
When booting as a coreboot payload, we don't need write any
configuration tables as coreboot does that for us.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Some platforms may have >=4GiB memory, so we need make U-Boot report
such configuration correctly when booting as the coreboot payload.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have generic routine to calculate relocation address,
remove the x86 specific one which is now only used by coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
coreboot has some extensions (type 6 & 16) to the E820 types.
When we detect this, mark it as E820_RESERVED.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Increase lib_sysinfo memrange entry number to 32 to sync with coreboot.
This allows a complete E820 table to be reported to the kernel, as on
some platforms (eg: Bayley Bay) having only 16 entires does not cover
all the memory ranges.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.
The following graph is modified from kernel gpmi-nand.c driver with
each data block 512 bytes. We can see that Block Mark conflicts with
ecc area from bch view. We can enlarge the ecc chunk size to avoid
this problem to those oobsize which is larger than 512.
| P |
|<----------------------------------------------------------------->|
| |
| (Block Mark) |
| P' | | | |
|<--------------------------------------------------->| D | | O'|
| |<--------->| |<->|
V V V V V
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
| M | data |E| data |E| data |E| data |E| |
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
^ ^
| O |
|<---------------->|
P : the page size for BCH module.
E : The ECC strength.
G : the length of Galois Field.
N : The chunk count of per page.
M : the metasize of per page.
C : the ecc chunk size, aka the "data" above.
P': the nand chip's page size.
O : the nand chip's oob size.
O': the free oob.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
This patch moves pxa to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) pxa timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locked the processor. Rather than patch the specific pxa issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsuiko.com>
Since commit 3ff46cc42b ("arm: relocate the exception vectors")
pxa does not boot anymore.
Add a specific relocate_vectors macro that skips the vector relocation,
as the pxa SoC does not provide RAM at the high vectors address
(0xFFFF0000), and (0x00000000) maps to ROM.
This allows pxa to boot again.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Conflicts:
configs/socfpga_arria5_defconfig
configs/socfpga_cyclone5_defconfig
configs/socfpga_socrates_defconfig
Merged these by hand and re-ran savedefconfig on them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the missing DT nodes, so that ArriaV SoCDK can boot from SD
card. The SD card must be in slot J5 and BSEL must be 0x5.
Signed-off-by: Marek Vasut <marex@denx.de>
Add "bank-name" property to each GPIO bank to give it unique name.
The approach here is exactly the same as with the "regulator-name"
property for regulators.
Signed-off-by: Marek Vasut <marex@denx.de>
Now that we're actually converting the QTS-generated header files,
we can even adjust their data types. A good candidate for this is
the pinmux table, where each entry can have value in the range of
0..3, but each element is declared as unsigned long. By changing
the type to u8, we can save over 600 Bytes from the SPL, so do it.
This patch also constifies the array.
Signed-off-by: Marek Vasut <marex@denx.de>
Add script which loads the QTS-generated sources and headers and converts
them into sensible format which can be used with much more easy in mainline
U-Boot. The script also filters out macros which makes no sense anymore, so
they don't pollute namespace and waste space.
Signed-off-by: Marek Vasut <marex@denx.de>
The board/altera/socfpga directory is not a generic SoCFPGA machine
anymore, but instead it represents the Altera SoCDK board. To make
matters more complicated, it represents both CycloneV and ArriaV
variant.
On the other hand, nowadays, the content of this board directory is
mostly comprised of QTS-generated header files, while all the generic
code is in arch/arm/mach-socfpga already.
Thus, this patch splits the board/altera/socfpga into a separate
board directory for ArriaV SoCDK and CycloneV SoCDK, so that each
can be populated with the correct QTS-generated header files for
that particular board.
Signed-off-by: Marek Vasut <marex@denx.de>
The CONFIG_TARGET_SOCFPGA_CYCLONE5 and CONFIG_TARGET_SOCFPGA_ARRIA5
selected both a board and a CPU. This is not correct as these macros
are supposed to select only board.
All would be good, if QTS-generated header files didn't check for
these macros exactly to determine if the platform is Cyclone V or
Arria V. Thus, for the sake of compatibility with not well fleshed
out header file generator, this patch makes these two macros into
a stub config option and introduces new CONFIG_TARGET_SOCFPGA_CYCLONE5_SOCDK
and CONFIG_TARGET_SOCFPGA_ARRIA5_SOCDK targets, which select the
previous stub config option.
The result is that compatibility with QTS is preserved and the new
CONFIG_TARGET_* select actual target boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Move the wrappers for QTS-generated files into platform directory
out of the board directory. The trick here is to add -I to CFLAGS
such that it points to the board directory in source tree and thus
the qts/ directory there is still reachable.
Signed-off-by: Marek Vasut <marex@denx.de>
The GMAC which is enabled is purely board property, so do not enable
arbitrary GMAC in DT include files. Same goes for PHY mode, which is
again a board property. The CycloneV SoCDK does this correctly, but
SoCrates doesn't. This bug never manifested itself though, since all
the boards ever used the GMAC1 . This bug manifests itself only on
boards that utilise GMAC0.
Signed-off-by: Marek Vasut <marex@denx.de>
Kishon Vijay Abraham I
Paul Kocialkowski
Stefan Roese
Lokesh Vutla
Nishanth Menon
Kun-Hua Huang
Tom Rini
Bin Meng
Simon Glass
Saket Sinha
Peng Fan
Marcel Ziswiler
Andrew Ruder
Marek Vasut