Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
OHCI has a known limitation of allowing only 32-bit DMA buffer
addresses, so we have a lot of u32 variables around, which are assigned
to pointers and vice versa. This obviously creates issues with 64-bit
systems, so the compiler complains here and there.
To allow compilation for 64-bit boards which use only memory below 4GB
anyway (and to avoid more invasive fixes), adjust some casts and types
and assume that the EDs and TDs are all located in the lower 4GB.
This fixes compilation of the OHCI driver for the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
On the H3 we need to enable the clk and de-assert the reset of the
companion to be able to talk to the actual usb host controller.
Before this commit we were also disabling the companion clk-gate /
asserting its reset on remove, causing the later remove callback of
the companion itself to (sometimes) fail with:
ERROR: USB HC reset timed out!
This commit fixes this by not disabling the companion's clk-gate nor
asserting its reset on remove.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The 2nd usb controller on sun4i/sun7i has its base address 0x8000
bytes from the 1st one, rather then 0x1000. Also the ahb clk gates
are interleaved with the ohci clk-gates introducing a hole between
the clks for usb1 and usb2.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tom Rini
Amit Singh Tomar
Andre Przywara
Hans de Goede
Chen-Yu Tsai
Jelle van der Waa