Commit graph

255 commits

Author SHA1 Message Date
Maximilian Schwerin
57210c7cc3 Add support for loading and saving the environment to a FAT partition
The following must be defined:

CONFIG_ENV_IS_IN_FAT
	Enable this saving environment to FAT.

FAT_ENV_INTERFACE
	Interface the FAT resides on (e.g. mmc).

FAT_ENV_DEVICE
	The interface device number (e.g. 0 for mmc0)

FAT_ENV_PART
	The device part (e.g. 1 for mmc0:1)

FAT_ENV_FILE
	The filename of the environment file.

Author:    Maximilian Schwerin <mvs@tigris.de>

Removed dead DEBUG comment.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-03-30 22:38:14 +02:00
Simon Schwarz
1648a37505 Add cmd_spl command
This adds a spl command to the u-boot.

Related config:
CONFIG_CMD_SPL
	activate/deactivate the command
CONFIG_CMD_SPL_NAND_OFS
	Offset in NAND to use

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
2012-03-27 22:05:28 +02:00
Matt Porter
24de357a30 SPL: Add YMODEM over UART load support
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.

Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-03-26 23:09:25 +02:00
Simon Glass
3a608ca01d bootstage: Implement core microsecond boot time measurement
This defines the basics of a new boot time measurement feature. This allows
logging of very accurate time measurements as the boot proceeds, by using
an available microsecond counter.

To enable the feature, define CONFIG_BOOTSTAGE in your board config file.
Also available is CONFIG_BOOTSTAGE_REPORT which will cause a report to be
printed just before handing off to the OS.

Most IDs are not named at this stage. For that I would first like to
renumber them all.

Timer summary in microseconds:
       Mark    Elapsed  Stage
          0          0  reset
    205,000    205,000  board_init_f
  6,053,000  5,848,000  bootm_start
  6,053,000          0  id=1
  6,058,000      5,000  id=101
  6,058,000          0  id=100
  6,061,000      3,000  id=103
  6,064,000      3,000  id=104
  6,093,000     29,000  id=107
  6,093,000          0  id=106
  6,093,000          0  id=105
  6,093,000          0  id=108
  7,089,000    996,000  id=7
  7,089,000          0  id=15
  7,089,000          0  id=8
  7,097,000      8,000  start_kernel

Signed-off-by: Simon Glass <sjg@chromium.org>
2012-03-18 21:42:14 +01:00
Marek Vasut
23faf2bc9e USB: Separate out USB hub driver
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-03-03 16:55:24 +01:00
Matthias Weisser
21899b1085 sandbox: Add improved RAM simulation
Using mmap to allocate memory from the OS for RAM simulation we can use
u-boot own malloc implementation.

Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-12-10 17:54:04 -05:00
Vadim Bendebury
576fb1ed3f Add a cli command to test the TPM device.
The command gets an arbitrary number of arguments (up to 30), which
are interpreted as byte values and are feed into the TPM device after
proper initialization. Then the return value and data of the TPM
driver is examined.

TPM commands are described in the TCG specification.

For instance, the following sequence is the 'TPM Startup' command, it
is processed by the TPM and a response is generated:

boot > tpm 0x0 0xc1 0x0 0x0 0x0 0xc 0x0 0x0 0x0 0x99 0x0 0x1
Found TPM SLB9635 TT 1.2 by Infineon
Got TPM response:
 00 c4 00 00 00 0a 00 00 00 00

If the command is corrupted (fed one byte short), an error is reported:
boot > tpm 0x0 0xc1 0x0 0x0 0x0 0xc 0x0 0x0 0x0 0x99 0x0
generic_lpc_tpm.c:311 unexpected TPM status 0xff000888
generic_lpc_tpm.c:516 failed sending data to TPM
tpm command failed
boot >

Change-Id: I3f3c5bfec8b852e208c4e99ba37b0f2b875140b0
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
CC: Wolfgang Denk <wd@denx.de>
2011-12-06 21:30:03 +01:00
Aneesh V
2d01dd953a omap: spl: fix build break due to changes in FAT
FAT library now uses malloc() and free(). But SPL doesn't
have heap until now. Setup a heap in SDRAM to fix this issue.

However this increases SPL footprint beyond the available SRAM
budget. So, compile out some fancy features in the SDARM init
bring back footprint under control

CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:35 +02:00
Simon Glass
fe34107e38 sandbox: Disable built-in malloc
We prefer to U-Boot's malloc but for now it is easier to use the C library's
version.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-17 23:56:57 +02:00
Jason Hobbs
06283a6401 Add pxe command
Add pxe command, which is intended to mimic PXELINUX functionality.
'pxe get' uses tftp to retrieve a file based on UUID, MAC address or IP
address. 'pxe boot' interprets the contents of PXELINUX config like file
to boot using a specific initrd, kernel and kernel command line.

This patch also adds a README.pxe file - see it for more details on the
pxe command.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
2011-10-17 22:25:35 +02:00
Jason Hobbs
b69bf52dfe Add generic, reusable menu code
This will be used first by the pxe code, but is intended to be
generic and reusable for other jobs in U-boot.

Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
2011-10-17 22:25:33 +02:00
Che-liang Chiou
ca366d0e38 cmd_time: add time command
The 'time' command runs and reports execution time of commands.

Sample usage:
--------------------
u-boot# time crc 0x1000 1000
CRC32 for 00001000 ... 00001fff ==> ae94dc4b

time: 0.004 seconds, 4 ticks
--------------------

Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-09 23:24:48 +02:00
York Sun
d29d17d7ba powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.

To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.

Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:06 -05:00
Jason Kridner
4421acf8cd led: added cmd_led to Makefile
Addition of cmd_led into the Makefile wasn't included in the patch
applied to u-boot-ti.

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:22 +02:00
Andreas Pretzsch
7130a579fd add command fitupd to run an update from a FIT image
Command calls update_tftp() analogous to automatic update described
in doc/README.update.

Usage:
fitupd [addr]
        - run update from FIT image at addr
          or from tftp 'updatefile'

Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
2011-07-26 16:58:48 +02:00
Aneesh V
05bad4aa56 scaled down version of generic libraries for SPL
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-26 14:44:25 +02:00
Wolfgang Denk
566e5cf451 ARM: drop unsupported 'trab' board
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it.  Drop it.

This includes support for VFD displays which have always been used by
this board only.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-22 20:00:51 +02:00
Wolfgang Denk
aef293bc85 Merge branch 'phylib' of git://git.denx.de/u-boot-mmc 2011-04-20 23:01:52 +02:00
Wolfgang Denk
9dd5dad887 Merge branch 'misc' of git://git.denx.de/u-boot-blackfin 2011-04-20 22:57:35 +02:00
Andy Fleming
995daa0b81 Add mdio command for new PHY infrastructure
The new mdio command doesn't have all of the features of the mii
command, but it provides the necessary read/write primitives, and allows
users to interact with 10G PHYs, and other PHYs which use Clause 45 of
802.3.  This means that the mdio command requires a "Device Address"
argument, though for clause 22 PHYs, the argument can be "-".

Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:35 -05:00
Andy Fleming
5f184715ec Create PHY Lib for U-Boot
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme.  The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support

The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).

The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.

We now have MDIO drivers and PHY drivers

An MDIO driver provides:
read
write
reset

A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed

The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()

Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)

We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.

We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,

we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.

Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:19 -05:00
Mike Frysinger
a972b8d701 gpio: generalize for all generic gpio providers
The Blackfin gpio command isn't terribly Blackfin-specific.  So generalize
the few pieces into two new optional helpers:
	name_to_gpio() - turn a string name into a GPIO #
	gpio_status() - display current pin bindings (think /proc/gpio)

Once these pieces are pulled out, we can relocate the cmd_gpio.c into the
common directory.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-13 15:56:51 -04:00
Mike Frysinger
c3d2a17c1e md5sum/sha1sum/unzip: split out of mondo mem file
There's no real need to keep these functions in the cmd_mem file since
they do not use any of the common global mem variables.  So split them
out into their own dedicated cmd files.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-13 15:56:47 -04:00
Thomas Chou
d52ebf1022 mmc: add generic mmc spi driver
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.

The crc checksum on data packet is enabled with the def,

There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2011-04-13 06:35:22 -05:00
Mike Frysinger
1ba7fd2567 Blackfin: ldrinfo: new command
Simple command to decode/check an LDR image before we try to boot it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08 00:44:27 -04:00
Mike Frysinger
52f0aa835f config_cmd_defaults.h: new header for common u-boot command defaults
We have config_defaults.h which are random configuration settings that
everyone gets by default.  We also have config_cmd_default.h which is a
recommended list of defaults but boards have to opt into.  Now we have
config_cmd_defaults.h which is a list of defaults that everyone gets
and has to actively opt out of.

For now, we populate it with the bootm command which previously was
unable to be disabled.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-01-09 18:01:03 +01:00
Wolfgang Denk
0390e26705 common/Makefile: don't include env_embedded.o into libcommon
Some boards use an embedded environment, where env_embedded.o has to
be linked at a special position in the U-Boot image; to make this
possible, we do not include it into libcommon.o for such boards.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-26 22:08:19 +01:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Terry Lv
a80603598c Save environment data to mmc.
This patch is to save environment data to mmc card.
It uses interfaces defined in generic mmc.

Signed-off-by: Terry Lv <r65388@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2010-09-19 17:47:29 +02:00
Heiko Schocher
88ffb2665c CRAMFS: support cramfs in RAM
cramfsls and cramfsload are added to the command list.
A cramfs placed at 'cramfs_addr' can the be listed with 'cramfsls' and files
can be loaded with 'cramfsload'. 'cramfs_addr' is an environment variable
specifying the address the cramfs is located.
This works for powerpc and for ARM.

Use CONFIG_CMD_CRAMFS.

Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
2010-01-18 00:44:13 +01:00
Robin Getz
0c909551f8 kgdb: add default generic stubs
The default kgdb functions can be implemented with common U-Boot functions,
so rather than force everyone to copy & paste these things, create a set of
weak stubs.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-18 00:23:00 +01:00
Wolfgang Denk
2a49bf3149 Merge branch 'master' into next
Conflicts:
	board/esd/plu405/plu405.c
	drivers/rtc/ftrtc010.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-05 02:11:59 +01:00
Peter Tyser
9ef78511cd circbuf: Move to lib_generic and conditionally compile
circbuf could be used as a generic library and is only currently
needed when CONFIG_USB_TTY is defined.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-12-02 23:19:32 +01:00
Peter Tyser
6b8f5ad10f command.c: Break commands out to appropriate cmd_*.c files
command.c should contain common code related to commands, not
miscellaneous command implementations.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-11-23 00:06:11 +01:00
Peter Tyser
581d04f14d cmd_nand: Move conditional compilation to Makefile
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-11-13 16:56:14 -06:00
Wolfgang Denk
a747a7f310 Revert "env: only build env_embedded and envcrc when needed"
Breaks building on many boards, and no really clean fix available yet.

This reverts commit 6dab6add2d.
2009-10-27 20:46:31 +01:00
Mike Frysinger
6dab6add2d env: only build env_embedded and envcrc when needed
The env code is protected by the ENV_IS_EMBEDDED define, so attempting to
compile the code when this isn't defined is pointless.  Now that the env
headers have unified around CONFIG_ENV_IS_EMBEDDED, convert the build
system to only build the env objects when this is enabled.  And now that
the env code is conditionally compiled, we can drop the source code checks.

For people who want to extract the environment manually, add a new option
CONFIG_BUILD_ENVCRC that only enables the envcrc utility.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-10-18 22:53:18 +02:00
Reinhard Arlt
52a0e2dee9 Add support for the Tundra TSI148 VME-bridge
From: Reinhard Arlt <reinhard.arlt@esd-electronics.com>

This patch adds support for the Tundra TSI148 VME-bridge. It's used on
the upcoming esd VME8349 board.

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-19 11:21:08 +02:00
Wolfgang Denk
a694610d33 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2009-07-19 00:38:23 +02:00
Jean-Christophe PLAGNIOL-VILLARD
52cb4d4fb3 stdio/device: rework function naming convention
So far the console API uses the following naming convention:

	======Extract======
	typedef struct device_t;

	int	device_register (device_t * dev);
	int	devices_init (void);
	int	device_deregister(char *devname);
	struct list_head* device_get_list(void);
	device_t* device_get_by_name(char* name);
	device_t* device_clone(device_t *dev);
	=======

which is too generic and confusing.

Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev

This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Edited commit message.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-18 00:27:46 +02:00
Scott Wood
be33b046b5 Remove legacy NAND and disk on chip code.
Legacy NAND had been scheduled for removal.  Any boards that use this
were already not building in the previous release due to an #error.

The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed.  There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 19:07:47 -05:00
Anton Vorontsov
93f9dcf9e8 Add simple hwconfig infrastructure
This patch implements simple hwconfig infrastructure: an
interface for software knobs to control a hardware.

This is very simple implementation, i.e. it is implemented
via `hwconfig' environment variable. Later we could write
some "hwconfig <enable|disable|list>" commands, ncurses
interface for Award BIOS-like interface, and frame-buffer
interface for AMI GUI[1] BIOS-like interface with mouse
support[2].

Current implementation details/limitations:

1. Doesn't support options dependencies and mutual exclusion.
   We can implement this by integrating apt-get[3] into the
   u-boot. But I didn't bother yet.

2. Since we don't implement hwconfig command, i.e. we're working
   with the environement directly, there is no way to tell that
   toggling a particular option will need a reboot to take
   an effect. So, for now it's advised to always reboot the
   target after modifying hwconfig variable.

3. We support hwconfig options with arguments. For example,

   set hwconfig dr_usb:mode=peripheral,phy_type=ulpi

   That means:
   - dr_usb - enable Dual-Role USB controller;
   - dr_usb:mode=peripheral - USB in Function mode;
   - dr_usb:phy_type=ulpi - USB should work with ULPI PHYs;

The purpose of this simple implementation is to define some
internal API and then we can continue improving user experience
by adding more mature interface, like hwconfig command with
bells and whistles. Or not adding, if we feel that current
interface fits its needs.

[1] http://en.wikipedia.org/wiki/American_Megatrends
[2] Regarding ncurses and GUI with mouse support -- I'm just
    kidding.
[3] The comment regarding apt-get is also a joke, meaning that
    dependency tracking could be non-trivial. For example, for
    enabling HW feature X we may need to disable Y, and turn Z
    into reduced mode (like RMII-only interface for ethernet,
    no MII).

    It's quite trivial to implement simple cases though.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
2009-07-16 22:23:53 +02:00
Mike Frysinger
dd14af7640 Blackfin: new spibootldr command
Newer Blackfin parts can an on-chip ROM that can boot LDRs over SPI flashes,
so add a new 'spibootldr' command to take advantage of it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-14 20:01:04 -04:00
Mike Frysinger
ecb1dc8922 Add support for Linux-like kallsysms
The kernel stores address<->symbol names in it so things can be decoded at
runtime.  Do it in U-Boot, and we get nice symbol decoding when crashing.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-12 20:45:48 +02:00
Jean-Christophe PLAGNIOL-VILLARD
55e0ed6078 make MODEM SUPPORT generic instead of duplicate it
and fix comment

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Adjusted Copyright message.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-06-12 20:45:47 +02:00
Wolfgang Denk
f63728c804 One more fix for building env_embedded.o
In addition to the changes for CONFIG_ENV_IS_IN_FLASH as done in
commit afcbce07, we also need to do the same for
CONFIG_ENV_IS_IN_EEPROM and CONFIG_ENV_IS_IN_NVRAM.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-05 00:18:44 +02:00
Jean-Christophe PLAGNIOL-VILLARD
b9c0e4c29e add dataflash mmc mux missing support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:20 +02:00
Wolfgang Denk
afcbce07e9 Fix building of env_embedded.o
Since commit a706bfc7 common/env_embedded.o and tools/envcrc were
only built when CONFIG_ENV_IS_EMBEDDED was set, but this breaks
building for many boards.

We always have to build these files when CONFIG_ENV_IS_IN_FLASH is
set.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-04 16:10:40 +02:00
Peter Tyser
a706bfc7d0 common/Makefile: Conditionally compile env_embedded.o
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-04-04 01:06:10 +02:00
unsik Kim
75eb82ec7c mflash: Initial mflash support
Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.

IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)

This driver support mflash IO mode.

Followings are brief descriptions about IO mode.

1. IO mode based on ATA protocol and uses some custom command. (read
   confirm, write confirm)
2. IO mode uses SRAM bus interface.

Signed-off-by: unsik Kim <donari75@gmail.com>
2009-04-03 23:47:06 +02:00
Wolfgang Denk
74de7aefd7 Add "source" command; prepare removal of "autoscr" command
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.

This patch prepares this change and starts a 6 month transition
period as follows:

- The new "source" command has been added, which implements exactly
  the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
  new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
  have *not* been adapted yet; these will be renamed resp. removed in
  a separate patch when the support for the "autoscr" command get's
  finally dropped.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-04-03 22:01:42 +02:00
Stefan Roese
ce6d0c8de0 UBIFS: Add UBIFS commands
This patchset adds these UBIFS related commands:

- ubifsmount
  Mount an UBIFS volume

- ubifsls
  List a directory of the mounted UBIFS volume

- ubifsload
  Load a file from the mounted UBIFS volume to memory

Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-20 22:39:15 +01:00
Stefan Roese
68d7d65100 Separate mtdparts command from jffs2
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-03-20 22:39:14 +01:00
Mike Frysinger
e915f8bb73 common/{hush, kgdb, serial}.c: build by COBJS-$(...) in Makefile
Move global '#ifdef CONFIG_xxx .... #endif' out of the .c files and into
the COBJS-$(CONFIG_xxx) in the Makefile.  Also delete unused var in kgdb
code in the process.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-11 23:05:57 +01:00
Gary Jennejohn
16a28ef219 IOMUX: Add console multiplexing support.
Modifications to support console multiplexing.  This is controlled using
CONFIG_SYS_CONSOLE_MUX in the board configuration file.

This allows a user to specify multiple console devices in the environment
with a command like this: setenv stdin serial,nc.  As a result, the user can
enter text on both the serial and netconsole interfaces.

All devices - stdin, stdout and stderr - can be set in this manner.

1) common/iomux.c and include/iomux.h contain the environment setting
implementation.
2) doc/README.iomux contains a somewhat more detailed description.
3) The implementation in (1) is called from common/cmd_nvedit.c to
handle setenv and from common/console.c to handle initialization of
input/output devices at boot time.
4) common/console.c also contains the code needed to poll multiple console
devices for input and send output to all devices registered for output.
5) include/common.h includes iomux.h and common/Makefile generates iomux.o
when CONFIG_SYS_CONSOLE_MUX is set.

Signed-off-by: Gary Jennejohn <garyj@denx.de>
2008-12-07 01:23:35 +01:00
Jean-Christophe PLAGNIOL-VILLARD
c8aa7dfc18 FPGA: move fpga drivers to drivers/fpga
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-05 22:41:33 +01:00
Kyungmin Park
694a0b3f1c UBI: Add UBI command support
This patch adds these UBI commands:

ubi part [nand|onenand] [part] - Show or set current partition
ubi info [l[ayout]] -Display volume and UBI layout information
ubi create[vol] volume [size] [type] - Create volume name with size
ubi write[vol] address volume size - Write volume from address with size
ubi read[vol] address volume [size] - Read volume to address with size
ubi remove[vol] volume - Remove volume

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Jean-Christophe PLAGNIOL-VILLARD
a80b21d512 common/Makefile: create others group for non core, environment and command files
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-11-02 16:33:07 +01:00
Bartlomiej Sieka
4bae90904b Automatic software update from TFTP server
The auto-update feature allows to automatically download software updates
from a TFTP server and store them in Flash memory during boot. Updates are
contained in a FIT file and protected with SHA-1 checksum.

More detailed description can be found in doc/README.update.

Signed-off-by: Rafal Czubak <rcz@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2008-10-18 21:54:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD
b64b775e75 cmd_mem: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:05 +02:00
Jean-Christophe PLAGNIOL-VILLARD
507641d249 env_flash: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0cf4fd3cf8 rename environment.c in env_embedded.c to reflect is functionality
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:01 +02:00
Jean-Christophe PLAGNIOL-VILLARD
c0878af6e3 env_nowhere: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:01 +02:00
Jean-Christophe PLAGNIOL-VILLARD
2556ef7811 env_sf: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD
55c5f49910 env_onenand: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD
957a0e6957 env_nvram: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:59 +02:00
Jean-Christophe PLAGNIOL-VILLARD
06f6135439 env_nand: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:59 +02:00
Jean-Christophe PLAGNIOL-VILLARD
d8cc04d0ac env_dataflash: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:58 +02:00
Jean-Christophe PLAGNIOL-VILLARD
d1034bc8db cmd_eeprom: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:52 +02:00
Jean-Christophe PLAGNIOL-VILLARD
bf5a7710ec env_eeprom: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:38 +02:00
Jean-Christophe PLAGNIOL-VILLARD
32628c5008 cmd_mac: Move conditional compilation to Makefile
finish remaning CFG_ID_EEPROM in CONFIG_ID_EEPROM
start in commit ad8f8687b7

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:37 +02:00
Jean-Christophe PLAGNIOL-VILLARD
e5648acab1 cmd_fdc: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:37 +02:00
Jean-Christophe PLAGNIOL-VILLARD
2d02d91d53 common/Makefile: add core command section
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:37 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0d92d4a699 cmd_vfd: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:37 +02:00
Wolfgang Denk
2c8ccf2728 Makefile: fix bug introduced by commit 47ffd6c2 2008-09-09 16:55:47 +02:00
Wolfgang Denk
47ffd6c2fc Makefile: compile and link each module just once
Several source files need to be compiled and linked when one or more
config options are selected. To allow for easy selection in the
Makefiles yet to avoild multiple compilation (which costs build time)
and especially multiple linking (which causes errors), we use
"COBJS = $(sort COBJS-y)" which eliminates duplicates.

By courtesy of Detlev Zundel who suggested this approach.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-09-09 15:45:18 +02:00
Jean-Christophe PLAGNIOL-VILLARD
c1de7a6daf devices: merge to list_head
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-31 04:24:55 +02:00
Jean-Christophe PLAGNIOL-VILLARD
578118bdf1 common/Makefile: order by functionality
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 21:53:57 +02:00
Jean-Christophe PLAGNIOL-VILLARD
ba7b5b2348 miiphyutil: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 21:53:56 +02:00
Jean-Christophe PLAGNIOL-VILLARD
81789c39db autoscript: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 21:53:37 +02:00
Jean-Christophe PLAGNIOL-VILLARD
bbf52df9aa crc16: move to lib_generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 12:25:02 +02:00
Jean-Christophe PLAGNIOL-VILLARD
55195773ea miiphybb: move to drivers/net/phy
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 12:25:02 +02:00
Jean-Christophe PLAGNIOL-VILLARD
e831403599 soft_spi: move to drivers/spi
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 12:25:02 +02:00
Jean-Christophe PLAGNIOL-VILLARD
4d75e0aa9c soft_i2c: move to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 12:25:02 +02:00
Jean-Christophe PLAGNIOL-VILLARD
717a222229 gunzip: move to lib_generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-29 12:25:01 +02:00
James Yang
0f2cbe3f5e Add proper SPD definitions for DDR1/2/3
Also adds helper functions for DDR1/2 to verify the checksum.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 02:05:53 +02:00
Kumar Gala
ffa4bafaca Add command to enable/disable interrupts
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-21 00:53:02 +02:00
Harald Welte
0a823aa2a8 Add 'license' command to U-Boot command line
The 'license' command includes the U-Boot license (GPLv2) into the
actual bootloader binary. The license text can be shown interactively
at the U-Boot commandline.

For products where the commandline can actually be accessed by the
end user, this helps to prevent inadvertent GPL violations, since the
GPLv2 license text can no longer be 'forgotten' to be included into
the product.

The 'license' command can be enabled by CONFIG_CMD_LICENSE.

Signed-off-by: Harald Welte <laforge@openmoko.org>
2008-08-18 23:21:49 +02:00
Jean-Christophe PLAGNIOL-VILLARD
d6e9ee92e8 common: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:38 +02:00
William Juul
90ef117b68 Incorporate yaffs2 into U-boot
To use YAFFS2 define CONFIG_YAFFS2

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:19 -05:00
Gerald Van Baren
fec6d9ee7c Remove the deprecated CONFIG_OF_FLAT_TREE
Use CONFIG_OF_LIBFDT instead to support flattened device trees.  It is
cleaner, has better functionality, and is better supported.

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2008-06-09 21:13:35 -04:00
Haavard Skinnemoen
8c66497e06 Add support for environment in SPI flash
This is pretty incomplete...it doesn't handle reading the environment
before relocation, it doesn't support redundant environment, and it
doesn't support embedded environment. But apart from that, it does
seem to work.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-03 20:33:11 +02:00
Haavard Skinnemoen
b6368467e6 SPI Flash: Add "sf" command
This adds a new command, "sf" which can be used to manipulate SPI
flash. Currently, initialization, reading, writing and erasing is
supported.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-03 20:32:25 +02:00
eran liberty
3c735e7437 Altera Stratix II support
Adds Support for Altera's Stratix II.

Within your board specific init file you will have to call

1. fpga_init (/* relocated code offset. usually => */ gd->reloc_off);
2. fpga_add (fpga_altera, (Altera_desc*)&altera_desc);

Altera_desc* contines (for example):
	{
	 Altera_StratixII,	/* part type */
	 passive_serial,	/* interface type */
	 1,			/* bytes of data part can accept */
	 (void *)(&funcs),	/* interface function table */
	 0L,			/* base interface address */
	 0			/* implementation specific cookie */
	 }

funcs is the interface. It is of type altera_board_specific_func.
It looks like this:
altera_board_specific_func func = {
	pre_fn,
	config_fn,
	status_fn,
	done_fn,
	clk_fn,
	data_fn,
	abort_fn,
	post_fn,
};

you will have to implement these functions, which is usually bit
banging some gpio.

Signed-off-by: Eran Liberty <liberty@extricom.com>
2008-04-13 14:52:48 -07:00
Daniel Hellstrom
2a2fa797e6 SPARC/LEON3: Added AMBA Bus Plug&Play information print command (ambapp). It can print available cores (type: AHB Master, AHB Slave, APB Slave), their address ranges, IRQ number and version.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
2008-04-08 07:58:32 +00:00
Wolfgang Denk
38b189fe74 Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xx 2008-03-27 00:16:34 +01:00
Dave Liu
c7057b529c ata: add the support for SATA framework
- add the SATA framework
- add the SATA command line

Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-03-26 23:38:51 +01:00
Dave Liu
9eef62804d ata: merge the ata_piix driver
move the cmd_sata.c from common/ to drivers/ata_piix.c,
the cmd_sata.c have some part of ata_piix controller drivers.
consolidate the driver to have better framework.

Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-03-26 23:38:48 +01:00
Kumar Gala
ec2b74ffd3 85xx: Added support for multicore boot mechanism
Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.

Added support for using the ePAPR defined spin-table mechanism on 85xx.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-26 11:43:03 -05:00
Bartlomiej Sieka
27f33e9f45 Merge branch 'new-image' of git://www.denx.de/git/u-boot-testing
Conflicts:

	common/cmd_bootm.c
	cpu/mpc8xx/cpu.c

Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2008-03-26 09:38:06 +01:00
Kumar Gala
d058698fd2 Add setexpr command
Add a simple expr style command that will set an env variable as the result
of the command.  This allows us to do simple math in shell.  The following
operations are supported: &, |, ^, +, -, *, /.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-03-25 22:16:15 +01:00
Mike Frysinger
cf675d3b2b Blackfin: new cplbinfo command for viewing cplb tables
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-15 22:14:54 -04:00
Mike Frysinger
86a20fb920 Blackfin: move bootldr command to common code
This moves the Blackfin-common bootldr command out of the BF537-STAMP
specific board directory and into the common directory so that all Blackfin
boards may utilize it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-03-15 22:13:58 -04:00
Marian Balakowicz
20c9395933 Merge branch 'master' of /home/git/u-boot 2008-02-21 17:18:01 +01:00
Marian Balakowicz
321359f208 [new uImage] Move gunzip() common code to common/gunzip.c
Move gunzip(), zalloc() and zfree() to a separate file.
Share zalloc() and zfree() with cramfs uncompress routine.

Signed-off-by: Marian Balakowicz <m8@semihalf.com>
2008-02-07 01:12:55 +01:00
Marian Balakowicz
b97a2a0a21 [new uImage] Define a API for image handling operations
- Add inline helper macros for basic header processing
- Move common non inline code common/image.c
- Replace direct header access with the API routines
- Rename IH_CPU_* to IH_ARCH_*

Signed-off-by: Marian Balakowicz <m8@semihalf.com>
2008-02-07 01:12:53 +01:00
Marian Balakowicz
ed29bc4e81 Add missing cmd_ximg.o to common/Makefile
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
2008-02-07 01:12:53 +01:00
Mike Frysinger
30942b18b6 new command for displaying strings at specified memory locations
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-02-04 19:26:57 -05:00
Mike Frysinger
d0b01a246d interface to Blackfin on-chip One-Time-Programmable memory
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-02-04 19:26:57 -05:00
Harald Welte
d16471ee05 add 'terminal program' functionality
This patch adds a 'cu' like serial terminal command to u-boot
using which you can access other serial ports from the system console.

OpenMoko uses this in their Neo1973 phones to get access to the GSM
Modem and GPS chip from the bootloader.

Signed-off-by: Harald Welte <laforge@openmoko.org>
2008-01-09 13:26:38 +01:00
Kumar Gala
9c9109e7fc Conditionally compile fdt_support.c
Modify common/Makefile to conditionally compile fdt_support.c based
on CONFIG_OF_LIBFDT.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2007-12-07 20:51:25 -05:00
Grant Likely
4a43719a77 [BUILD] conditionally compile common/cmd_*.c in common/Makefile
Modify common/Makefile to conditionally compile the cmd_*.c files based
on the board config.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-11-20 22:33:54 -07:00
Grant Likely
f0037c56b0 Build: split COBJS value into multiple lines
This change is in preparation for condtitionial compile support in the
build system.  By spliting them all into seperate lines now, subsequent
patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_<blah>) += ' will
be less invasive and easier to review

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-11-15 11:05:18 -07:00
Kyungmin Park
d7e8ce101a OneNAND support (take #2)
[PATCH 3/3] OneNAND support (take #2)

OneNAND support at U-Boot

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2007-09-17 08:19:08 +02:00
Wolfgang Denk
3a71b5ca77 Merge with /home/git/u-boot 2007-05-17 00:06:11 +02:00
mushtaq khan
66d9dbec1c Add driver for S-ATA-controller on Intel processors with South
Bridge, ICH-5, ICH-6 and ICH-7. 

Implementation:

1. Code is divided in to two files. All functions, which are
   controller specific are kept in "drivers/ata_piix.c" file and
   functions, which are not controller specific, are kept in
   "common/cmd_sata.c" file.

2. Reading and Writing from the S-ATA drive is done using PIO method.

3. Driver can be configured for 48-bit addressing by defining macro
   CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
   addressing.

4. S-ATA read function is hooked to the File system, commands like
   ext2ls and ext2load file can be used. This has been tested.

5. U-Boot command "SATA_init" is added, which initializes the S-ATA
   controller and identifies the S-ATA drives connected to it.

6. U-Boot command "sata" is added, which is used to read/write, print
   partition table and get info about the drives present. This I have
   implemented in same way as "ide" command is implemented in U-Boot.

7. This driver is for S-ATA in native mode.

8. This driver does not support the Native command queuing and
   Hot-plugging.

Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
2007-05-15 23:25:37 +02:00
Michal Simek
3c4bd60de1 Merge git://www.denx.de/git/u-boot
Conflicts:

	include/asm-microblaze/microblaze_intc.h
	include/linux/stat.h
2007-05-08 00:32:35 +02:00
Michal Simek
ffc50f9bb1 new: FSL and MSR support #2 2007-05-05 18:54:42 +02:00
Gerald Van Baren
64dbbd40c5 Moved fdt command support code to fdt_support.c
...in preparation for improving the bootm command's handling of fdt blobs.
Also cleaned up some coding sloppiness.
2007-04-06 14:19:43 -04:00
Gerald Van Baren
213bf8c822 Add a flattened device tree (fdt) command (2 of 2)
Modifications to the existing code to support the new fdt command.
2007-03-31 12:23:51 -04:00
Grant Likely
3a8ce9af6f [PATCH 6_9] Move common_cmd_ace.c to drivers_systemace.c
The code in this file is not a command; it is a device driver.  Put it in
the correct place.  There are zero functional changes in this patch, it
only moves the file.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-02-20 09:05:23 +01:00
Stefan Roese
dfc8a9ee00 Merge with /home/stefan/git/u-boot/denx 2006-11-10 07:48:47 +01:00
Jon Loeliger
daaba9859b Merge branch 'master' of http://www.denx.de/git/u-boot 2006-10-10 17:21:42 -05:00
Wolfgang Denk
2b208f5308 Move "ar" flags to config.mk to allow for silent "make -s"
Based on patch by Mike Frysinger, 20 Jun 2006
2006-10-09 01:02:05 +02:00
Jon Loeliger
afa98843e4 Merge branch 'master' of http://www.denx.de/git/u-boot
Conflicts:

	board/stxxtc/Makefile
2006-09-19 08:51:24 -05:00
Stefan Roese
64cd52efd1 Merge with /home/stefan/git/u-boot/denx 2006-09-18 10:48:03 +02:00
Marian Balakowicz
f93286397e Add support for a saving build objects in a separate directory.
Modifications are based on the linux kernel approach and
support two use cases:

  1) Add O= to the make command line
  'make O=/tmp/build all'

  2) Set environement variable BUILD_DIR to point to the desired location
  'export BUILD_DIR=/tmp/build'
  'make'

The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'

Command line 'O=' setting overrides BUILD_DIR environent variable.

When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
2006-09-01 19:49:50 +02:00
Stefan Roese
f0ff4692ff Add FPGA Altera Cyclone 2 support
Patch by Heiko Schocher, 15 Aug 2006
2006-08-15 14:15:51 +02:00
Haiying Wang
bea3f28d28 Add support for reading and writing mac addresses to or from ID EEPROM.
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.

U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).

If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.

Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2006-07-13 10:57:37 -05:00
Markus Klotzbuecher
f2841d3770 Add support for ymodem protocol (loady command).
Patch by Stefano Babic, 29 Mar 2006
2006-03-30 13:40:55 +02:00
Wolfgang Denk
f57f70aab9 Support passing of OF flat trees to the kernel.
Patch by Pantelis Antoniou, 04 Sep 2005
2005-10-13 01:45:54 +02:00
Wolfgang Denk
875c78934e Add Xilinx Spartan3 family FPGA support
Patch by Kurt Stremerch, 14 February 2005
2005-09-25 16:44:21 +02:00
Wolfgang Denk
9f96ae44c6 Add keyboard and dot matrix display support for HMI1001 board. 2005-08-30 13:04:12 +02:00
stroese
1740618202 - ext2fs support added
- Tundra universe support added
2004-12-16 17:35:57 +00:00
wdenk
8655b6f860 * Clean up tools/bmp_logo.c to not add trailing white space
* Patch by Hinko Kocevar, 21 Aug 2004:
  - Group common framebuffer functions in common/lcd.c
  - Group common framebuffer macros and #defines in include/lcd.h
  - Provide calc_fbsize() for video ATAG
2004-10-09 23:25:58 +00:00
wdenk
281e00a3be * Code cleanup
* Patch by Sascha Hauer, 28 Jun:
  - add generic support for Motorola i.MX architecture
  - add support for mx1ads, mx1fs2 and scb9328 boards

* Patches by Marc Leeman, 23 Jul 2004:
  - Add define for the PCI/Memory Buffer Configuration Register
  - corrected comments in cpu/mpc824x/cpu_init.c

* Add support for multiple serial interfaces
  (for example to allow modem dial-in / dial-out)
2004-08-01 22:48:16 +00:00
wdenk
13a5695b7c Patch by Jian Zhang, 20 May 2004:
add support for environment in NAND flash
2004-06-09 14:58:14 +00:00
wdenk
518e2e1ae3 * Patch by Pavel Bartusek, 21 Mar 2004
Add Reiserfs support

* Patch by Hinko Kocevar, 20 Mar 2004
  - Add auto-release for SMSC LAN91c111 driver
  - Add save/restore of PTR and PNR regs as suggested in datasheet
2004-03-25 14:59:05 +00:00
wdenk
232c150a25 Add support for Siemens SX1 mobile phone;
add support for USB-based console
(enable with "setenv stdout usbtty; setenv stdin usbtty")
2004-03-12 00:14:09 +00:00
wdenk
2d1a537d87 * Patch by Thomas Elste, 10 Feb 2004:
Add support for NET+50 CPU and ModNET50 board

* Patch by Sam Song, 10 Feb 2004:
  Fix typos in cfi_flash.c

* Patch by Leon Kukovec, 10 Feb 2004
  Fixed long dir entry slot id calculation in get_vfatname

* Patch by Robin Gilks, 10 Feb 2004:
  add "itest" command (operators: -eq, -ne, -lt, -gt, -le, -ge, ==,
  !=, <>, <, >, <=, >=)
2004-02-23 19:30:57 +00:00
wdenk
3f85ce2785 * CVS add missing files
* Cleanup compiler warnings

* Fix problem with side effects in macros in include/usb.h

* Patch by David Benson, 13 Nov 2003:
  bug 841358 - fix TFTP download size limit

* Fixing bug 850768:
  improper flush_cache() in load_serial()

* Fixing bug 834943:
  MPC8540 - missing volatile declarations

* Patch by Stephen Williams, 09 Feb 2004:
  Add support for Xilinx SystemACE chip:
  - New files common/cmd_ace.c and include/systemace.h
  - Hook systemace support into cmd_fat and the partition manager

* Patch by Travis Sawyer, 09 Feb 2004:
  Add bi_opbfreq & bi_iic_fast to 440GX bd_info as needed for Linux
2004-02-23 16:11:30 +00:00
wdenk
c83bf6a2d0 Add a common get_ram_size() function and modify the the
board-specific files to invoke that common implementation.
2004-01-06 22:38:14 +00:00
wdenk
5779d8d985 * Patch by Nicolas Lacressonnière, 12 Nov 2003:
update for for Atmel AT91RM9200DK development kit:
  - support for environment variables in DataFlash
  - Atmel DataFlash AT45DB1282 support

* Patch by Jeff Carr, 11 Nov 2003:
  add support for new version of 8270 processors

* Patches by George G. Davis, 05 Nov 2003:
  - only pass the ARM linux initrd tag to the kernel when an initrd
    is actually present
  - update omap1510inn configuration file
2003-12-06 23:55:10 +00:00
wdenk
a8c7c708a9 * Patch by Gleb Natapov, 19 Sep 2003:
Move most of the timer interrupt related PPC code to ppc_lib/interrupts.c

* Patch by Anders Larsen, 17 Sep 2003:
  Bring ARM memory layout in sync with the documentation:
  stack and malloc-heap are now located _below_ the U-Boot code
2003-12-06 19:49:23 +00:00
wdenk
5da627a424 * Patch by Steven Scholz, 10 Oct 2003
- Add support for Altera FPGA ACEX1K

* Patches by Thomas Lange, 09 Oct 2003:
  - Endian swap ATA identity for all big endian CPUs, not just PPC
  - MIPS only: New option CONFIG_MEMSIZE_IN_BYTES for passing memsize
    args to linux
  - add support for dbau1x00 board (MIPS32)
2003-10-09 20:09:04 +00:00
wdenk
1f4bb37d6b * Patch by Scott McNutt, 21 Jul 2003:
Add support for LynuxWorks Kernel Downloadable Images (KDIs).
  Both LynxOS and BlueCat linux KDIs are supported.

* Patch by Richard Woodruff, 25 Jul 2003:
  use more reliable reset for OMAP/925T

* Patch by Nye Liu, 25 Jul 2003:
  fix typo in mpc8xx.h

* Patch by Richard Woodruff, 24 Jul 2003:
  Fixes for cmd_nand.c:
  - Fixed null dereferece which could result in incorrect ECC values.
  - Added support for devices with no Ready/Busy signal hooked up.
  - Added OMAP1510 read/write protect handling.
  - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
    for non-JFFS2.
  - Switched default ECC to be JFFS2.
2003-07-27 00:21:01 +00:00
wdenk
27b207fd0a * Implement new mechanism to export U-Boot's functions to standalone
applications: instead of using (PPC-specific) system calls we now
  use a jump table; please see doc/README.standalone for details

* Patch by Dave Westwood, 24 Jul 2003:
  added support for Unity OS (a proprietary OS)
2003-07-24 23:38:38 +00:00
wdenk
8bde7f776c * Code cleanup:
- remove trailing white space, trailing empty lines, C++ comments, etc.
  - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)

* Patches by Kenneth Johansson, 25 Jun 2003:
  - major rework of command structure
    (work done mostly by Michal Cendrowski and Joakim Kristiansen)
2003-06-27 21:31:46 +00:00
wdenk
71f9511803 * Fix CONFIG_NET_MULTI support in include/net.h
* Patches by Kyle Harris, 13 Mar 2003:
  - Add FAT partition support
  - Add command support for FAT
  - Add command support for MMC
  ----
  - Add Intel PXA support for video
  - Add Intel PXA support for MMC
  ----
  - Enable MMC and FAT for lubbock board
  - Other misc changes for lubbock board
2003-06-15 22:40:42 +00:00
wdenk
7a8e9bed17 * Patch by Marc Singer, 29 May 2003:
Fixed rarp boot method for IA32 and other little-endian CPUs.

* Patch by Marc Singer, 28 May 2003:
  Added port I/O commands.

* Patch by Matthew McClintock, 28 May 2003
  - cpu/mpc824x/start.S: fix relocation code when booting from RAM
  - minor patches for utx8245

* Patch by Daniel Engström, 28 May 2003:
  x86 update

* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
  add nand flash support to SXNI855T configuration
  fix/extend nand flash support:
  - fix 'nand erase' command so does not erase bad blocks
  - fix 'nand write' command so does not write to bad blocks
  - fix nand_probe() so handles no flash detected properly
  - add doc/README.nand
  - add .jffs2 and .oob options to nand read/write
  - add 'nand bad' command to list bad blocks
  - add 'clean' option to 'nand erase' to write JFFS2 clean markers
  - make NAND read/write faster

* Patch by Rune Torgersen, 23 May 2003:
  Update for MPC8266ADS board
2003-05-31 18:35:21 +00:00