Commit graph

15 commits

Author SHA1 Message Date
Tom Rix
2ec1abea43 OMAP3 zoom2 Use usbtty if the debug board is not connected.
The preferred serial output comes from the debug board.
When the debug board is disconnected, fall back on using
usbtty from the usb connector on the Zoom2 board.

This shows up as /dev/ttyACM0 in a linux host.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:51:51 +01:00
Heiko Schocher
4b142febff common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-08 22:14:07 +01:00
Nishanth Menon
30563a04bf OMAP3:SDRC: introduce DDR types
Micron DDR timings based on:
http://www.sakoman.net/cgi-bin/gitweb.cgi?p=x-load-omap3.git;a=blob;f=include/asm/arch-omap3/mem.h;h=e6fbfe3947f5d0d85fea776e30821d4017316d86;hb=HEAD

Introduce Micron DDR timings and provide
CONFIG_OMAP3_INFINEON_DDR and CONFIG_OMAP3_MICRON_DDR config
options to allow for platform files to setup their timings as
per the type of DDR selected

Reported-by: Steve Sakoman in http://www.nabble.com/forum/Permalink.jtp?root=25779518&post=25959734&page=y

Signed-off-by: Nishanth Menon <nm@ti.com>
2009-11-27 16:26:16 -06:00
Sandeep Paulraj
9c44ddccb6 TI: OMAP3: Remove SZ_xx references
This patch removes dependency on the sizes.h header file
and removes all references to SZ_xx.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-10-18 16:52:52 -05:00
Tom Rix
0297ec7e2a TI OMAP3 Use arm init sequence to initialize i2c
This changes fixes an early i2c error.

It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.

While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.

Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.

Run tested on Beagle.
Compile tested on the omap3's

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2009-10-13 06:17:37 -05:00
Dirk Behme
97a099eaa4 omap3: remove typedefs for configuration structs
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-08-08 11:33:23 +02:00
Matthias Ludwig
187af954cf omap3: embedd gpmc_cs into gpmc config struct
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html

Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
2009-08-07 23:31:51 +02:00
Tom Rix
2c15513010 OMAP3 Move twl4030 power and led functions
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.

power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.

The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.

The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c  The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED

The directory board/omap3/common was removed because power_init_r
was the only function in it.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-29 09:57:30 +02:00
Tom Rix
cd7826359e TWL4030 Add power reset button
The Zoom2 power reset button is on the top right side of the
main board.  Press and hold for about to 8 seconds to completely
reset the board.

Some of the beta boards have a hardware problem that prevents
using this feature.  If is difficult to further characterize the
boards that fail.  So disable resetting for all beta boards.

The Zoom1 reset button is the red circle on the top right,
front of the board.  Press and hold the button for 8 seconds to
completely reset the board.

After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.

The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.

The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-28 08:56:31 +02:00
Wolfgang Denk
2eb99ca802 NAND: Part 2: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.

This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-18 21:56:15 +02:00
Tom Rix
0c9520efd6 ZOOM2 Define GPIO banks used.
Enable the function and interface clocks for banks 2,3,5 and 6.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2009-06-12 20:45:47 +02:00
Dirk Behme
3962c4f9fc OMAP3: Zoom2: Enable Board and CPU info
With other OMAP3 boards we recently switched to CPU and Board
info API. From parallel merge, this is missing for Zoom2.
Enable it for Zoom2, too.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:53 +02:00
Tom Rix
83ae698ff2 ZOOM2 Add led support.
This patch controls the large LED on the top left of the zoom2.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:53 +02:00
Tom Rix
660888b7fb ZOOM2 Add serial support.
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS.  On your host pick the first
enumeration.

The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.

The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.

The kernel bootargs are
console=ttyS3,115200n8

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:53 +02:00
Tom Rix
376aee78dd ZOOM2 Add initial support for Zoom2
Zoom2 is a new board from Texas Instruments and LogicPD

The logicpd web site is a good source for general information on this board.
Please start looking here if the below links are broken.
http://www.logicpd.com

This is a pdf of the product
http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf
This is the product description web page
http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp

This patch provides a zoom2 base target by copying zoom1 and by making some
obvious changes.

To configure, run
make omap3_zoom2_config

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:50 +02:00