This patch fixes the following compilation warning:
miiphy.c: In function 'emac4xx_miiphy_read':
miiphy.c:353: warning: dereferencing type-punned pointer will break
strict-aliasing rules
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the CONFIG_PCI_4xx_PTM_OVERWRITE option and replaces
the ugly 'if defined(BOARD1) || ... || defined(BOARDn)' construct
in 4xx pci code.
When CONFIG_PCI_4xx_PTM_OVERWRITE is defined the default ptm register
setup can be overwritten through environment variables ptm1la, ptm1ms,
ptm2la and ptm2ms to do application specific pci target BAR configuration.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Some board ports place TEXT_BASE at a location that would cause the
RESET_VECTOR_ADDRESS not to be at 0xfffffffc when we link. By default
we assume RESET_VECTOR_ADDRESS will be 0xfffffffc if the board doesn't
explicitly set it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
There is no reason to do a run time check for e500 v1 based cores to
determine if we have the GUTs RSTCR facility. Only the first generation
of PQ3 parts (MPC8540/41/55/60) do not have it. So checking to see if
we are e500 v2 would miss future parts (like e500mc).
Just change this to be ifdef'd based on CONFIG_MPC85{40,41,55,60}.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
While in probecpu() UART is still not initialized.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixing the number of cores in the device tree based on the actual number of
cores on the system. With this same device tree image can be used for dual
core and single core members of otherwise exactly same SOC.
For example:
* P2020RDB and P2010RDB
* P1020RDB and P1011RDB
* MPC8641D and MPC8641
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incase the system is detected with Unknown SVR, let the system boot
with a default value and a proper message.
Now with dynamic detection of SOC properties from SVR, this is necessary
to prevent a crash.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor the code into a simple bitmask lookup table that determines if
a given PCI controller is enabled and if its in host/root-complex or
agent/end-point mode.
Each processor in the PQ3/MPC86xx family specified different encodings
for the cfg_host_agt[] and cfg_IO_ports[] boot strapping signals.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleaned up cpu/mpc85xx/Makefile to use CONFIG_* for those obvious cases
we have like PCI, CPM2, QE. Also reworked it to use one line per file
for everything and sorted in alphabetical order.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Its possible that we try and copy the boot page code out of flash into a
DDR location that doesn't have a TLB cover it. For example, if we have
3G of DDR we typically only map the first 2G. In the cases of 4G+ this
wasn't an issue since the reset page TLB mapping covered the last page
of memory which we wanted to copy to.
We now change the physical address of the reset page TLB to map to the
true physical location of the boot page code, copy and than set the
TLB back to its 1:1 mapping of the reset page.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allow us to search the TLB array based on an address. This is useful
if we want to change an entry but dont know where it happens to be
located.
For example, the boot page mapping we use on MP or the flash TLB that
we change the WIMGE settings for after we've relocated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In future Book-E implementations IVORs will most likely go away and be
replaced with fixed offsets. The IVPR will continue to exist to allow
for relocation of the interrupt vectors.
This code adds support to setup the IVORs as their fixed offset values
per the ISA 2.06 spec when we transition from u-boot to another OS
either via 'bootm' or a cpu release.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ddr_pd_cntl isn't defined in any reference manual and thus we wil
remove especially since we set it to 0, which would most likely be its
POR value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable eSDHC Clock based on generic CONFIG_FSL_ESDHC define instead of a
platform define. This will enable all the 85xx platforms to use sdhc_clk
based on CONFIG_FSL_ESDHC.
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reset any i2c devices that may have been interrupted during a system reset.
Normally this would be accomplished by clocking the line until SCL and SDA
are released and then sending a start condtiion (From an Atmel datasheet).
There is no direct access to the i2c pins so instead create start commands
through the i2c interface. Send a start command then delay for the SDA Hold
time, repeat this by disabling/enabling the bus a total of 9 times.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Change PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY (Originally done in
commit ff4e66e93c, regressed by commit 6d7f610b09)
Cast PCI_ROM_ADDRESS_MASK to u32
Wrap probe_pci_video() call inside #ifdef CONFIG_VIDEO
Change call to pci_find_class() to pci_find_devices(). This is based on a
patch submitted on 1st March 2007 (Patch that fixes the compilation errors
for sc520_cdp board) by mushtaq_k
This patch requires that PCI_VIDEO_VENDOR_ID and PCI_VIDEO_DEVICE_ID be
specified in the board config file. Dummy values have been added for the
SC520 CDP board to enable compilation, but since I do not have one of these,
I do know what the values should be
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
The current implementation has the timer being started before the interrupt
handler is installed. It the interrupt occurs before the handler is
installed, the timer interrupt is never reset and the timer stops
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
gcc 4.3.2 optimiser creates multiple copies of inline asm (who knows why)
Remove use of global names for labels to prevent 'symbol already defined'
errors
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
If the memory layout pushes the stack out of the default DCPLB coverage,
the exception handler may trigger a double fault by trying to push onto
the uncovered stack. So handle the exception stack similar to the kernel
by using the top of the scratch pad SRAM.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This feature can be used to trigger special command "sysrstcmd" using
reset key long press event and environment variable "sysrstdelay" is set
(useful for reset to factory or manufacturing mode execution)
Kirkwood SoC implements a hardware-based SYSRSTn duration counter.
When SYSRSTn is asserted low, a SYSRSTn duration counter is running.
The counter value is stored in the SYSRSTn Length Counter Register
The counter is based on the 25-MHz reference clock (40ns)
It is a 29-bit counter, yielding a maximum counting duration of
2^29/25 MHz (21.4 seconds). When the counter reach its maximum value,
it remains at this value until counter reset is triggered by setting
bit 31 of KW_REG_SYSRST_CNT
Implementation:
Upon long reset assertion (> ${sysrstdelay} in secs) sysrstcmd will be
executed if pre-defined in environment variables.
This feature will be disabled if "sysrstdelay" variable is unset.
for-ex.
setenv sysrst_cmd "echo starting factory reset;
nand erase 0xa0000 0x20000;
echo finish ed sysrst command;"
will erase particular nand sector if triggered by this event
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems
<http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC
running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard
battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND
flash, two USB host ports, and an USB device port. More informations can be
found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
This patch adds support for i.MX27-LITEKIT development board from
LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND
flash, FEC ethernet controller integrated into i.MX27.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
The MPIC initialization code for Freescale e500 CPUs was not using I/O
accessors, and it was not issuing a read-back to the MPIC after setting
mixed mode. This may be the cause of a spurious interrupt on some systems.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1011 - Single core variant of P1020
P2010 - Single core variant of P2020
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are really no differences between all the 85xx linker scripts so
we can just move to a single common one. Board code is still able to
override the common one if need be.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020 is another member of QorIQ series of processors which falls in ULE
category. It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities.
Also the SOC is pin compatible with P2020
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The number of CPUs are getting detected dynamically by checking the
processor SVR value. Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.
This can help to use the same u-boot image across the platforms.
Also revamped and corrected few Freescale Copyright messages.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed same code pieces from cpu/mpc85xx/cpu.c and cpu/mpc86xx/cpu.c
and moved to cpu/mpc8xxx/cpu.c(new file)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For historic reasons we had defined some additional PLATFORM_CPPFLAGS like:
PLATFORM_CPPFLAGS += -DCONFIG_MPC86xx=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC8641=1
However these are all captured in the config.h and thus redudant. Also
moved common 86xx flags into cpu/mpc86xx/config.mk.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For historic reasons we had defined some additional PLATFORM_CPPFLAGS
like:
PLATFORM_CPPFLAGS += -DCONFIG_E500=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
PLATFORM_CPPFLAGS += -DCONFIG_MPC8548=1
However these are all captured in the config.h and thus redudant.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change %08lX to %08X in board.c. Remove unused variable
'oscillator' in mcf5227x/cpu_init.c and 'scm2' in
mcf532x/cpu_init.c. Provide argument type cast in
drivers/dma/MCD_dmaApi.c.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Support USB on PSC3 on the mpc5200. Before this patch, enabling USB support
would reconfigure PSC4 and PSC5 to USB. The mpc5200 does not support USB
enabled on both the standard USB port and PSC3. This patch masks the
appropriate bits when enabling USB.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Remy Bohmer <linux@bohmer.net>
For some time there have been repeated reports about build problems
with some ARM (cross) tool chains. Especially issues about
(in)compatibility with the tool chain provided runtime support
library libgcc.a caused to add and support a private implementation
of such runtime support code in U-Boot. A closer look at the code
indicated that some of these issues are actually home-made. This
patch attempts to clean up some of the most obvious problems and make
building of U-Boot with different tool chains easier:
- Even though all ARM systems basicy used the same compiler options
to select a specific ABI from the tool chain, the code for this was
distributed over all cpu/*/config.mk files. We move this one level
up into lib_arm/config.mk instead.
- So far, we only checked if "-mapcs-32" was supported by the tool
chain; if yes, this was used, if not, "-mabi=apcs-gnu" was
selected, no matter if the tool chain actually understood this
option. There was no support for EABI conformant tool chains.
This patch implements the following logic:
1) If the tool chain supports
"-mabi=aapcs-linux -mno-thumb-interwork"
we use these options (EABI conformant tool chain).
2) Otherwise, we check first if
"-mapcs-32"
is supported, and then check for
"-mabi=apcs-gnu"
If one test succeeds, we use the first found option.
3) In case 2), we also test if "-mno-thumb-interwork", and use
this if the test succeeds. [For "-mabi=aapcs-linux" we set
"-mno-thumb-interwork" mandatorily.]
This way we use a similar logic for the compile options as the
Linux kernel does.
- Some EABI conformant tool chains cause external references to
utility functions like raise(); such functions are provided in the
new file lib_arm/eabi_compat.c
Note that lib_arm/config.mk gets parsed several times, so we must
make sure to add eabi_compat.o only once to the linker list.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Dirk Behme <dirk.behme@googlemail.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
Tested-by: Andrzej Wolski <awolski@poczta.fm>
Tested-by: Gaye Abdoulaye Walsimou <walsimou@walsimou.com>
Tested-by: Tom Rix <Tom.Rix@windriver.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
When we init the addrmap based on the TLB we will not end up getting
the TLB that covers memory if we are using SPD. The reason is we
haven't relocated at the point that we setup the memory TLB and thus it
will not get setup in the addrmap.
Instead we can just walk over the TLB array after we've relocated and
see all the TLBs that have been set and use that information to populate
the initial addrmap. By doing this we insure that we get the TLB
entries that cover memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards. As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.
IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
