Commit graph

57 commits

Author SHA1 Message Date
pekon gupta
b80a660338 mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device bus-width
GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL:    SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
        which is called before probing for devices, hence any ONFI parameter
        information is not available during GPMC initialization.

Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.

This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:06 -04:00
Nishanth Menon
161d2d5ea8 omap3: zoom1: switch to generic ti_omap3_common config header
ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:40 -04:00
Nishanth Menon
ea467c73ed omap3: zoom1: fix default console
We do not use ttyS2 anymore in Linux, it changed to ttyO2 a few years
back. never too late to update.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:40 -04:00
Nishanth Menon
c2e7c7b2d9 omap3: zoom1: enable bootz
Boot from zImage and fdt_file if uImage is not available to maintain
the legacy behavior.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Nishanth Menon
4e8183b7d4 omap3: zoom1: disable JFFS2 and enable FS_GENERIC
This is more in line with commits
664979a2a9f764b63b8094458b87247d254b0cc1(omap3_beagle: remove JFFS2
support.) and 102ce9ea7a (omap3_beagle:
enable CMD_FS_GENERIC and simplify load of image/ramdisk)

CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we'd have to use. Sticking with existing conventions,
defaults will be:
bootfile=uImage
bootpart=0:1 (first partition)
bootdir=/ (/ in first partition)

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Nishanth Menon
d71dd0428c omap3: zoom1: enable common network commands
Basic networking commands for usability.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Nishanth Menon
9d70e77285 OMAP3: zoom1: enable LAN9211
Zoom1 was wrongly setup for LAN91C96. Fix it by enabling
LAN9211.

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
Nishanth Menon
ae3248a3fd omap3: zoom1: enable CONFIG_SYS_GENERIC_BOARD
CONFIG_SYS_GENERIC_BOARD should now be enabled for generic
functionality Further information in doc/README.generic-board

Signed-off-by: Nishanth Menon <nm@ti.com>
2014-04-17 17:24:39 -04:00
pekon gupta
a7e36fc95f mtd: nand: omap: remove unused #defines from common omap_gpmc.h
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
	- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
	- GPMC_NAND_ECC_LP_x8_LAYOUT  (for large page x8 NAND)
	- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
	- GPMC_NAND_ECC_SP_x8_LAYOUT  (for small page x8 NAND)

2) removes unused #defines in common omap_gpmc.h depending on above configs

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Rob Herring
f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Lokesh Vutla
806d279247 ARM: OMAP: Add CONFIG_OMAP_COMMON
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Michael Jones
019be4af64 Remove unused CONFIG_SYS_I2C_BUS[_SELECT]
"CONFIG_SYS_I2C_BUS" and "CONFIG_SYS_I2C_BUS_SELECT" don't appear anywhere
outside of config files.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-01-29 06:40:01 +01:00
Thomas Weber
abcbe2eb00 OMAP3: Remove unused PHYS_SDRAM_1_SIZE
Remove the unused PHYS_SDRAM_1_SIZE from OMAP3 config files.

Signed-off-by: Thomas Weber <thomas@tomweber.eu>
2012-12-10 12:45:34 -07:00
Andrew Bradford
669681104d configs: Fix usage of mmc rescan
Fix usage of 'mmc rescan' by many configs.  Proper use is
'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan
the device.  'mmc rescan' itself does not take any arguments.

Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
2012-10-23 08:33:17 -07:00
Rob Herring
3d6ba91e79 ARM: Remove unused stack and irq config defines
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.

IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-09-01 14:58:22 +02:00
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Thomas Weber
1378cac669 OMAP3: Remove unused define CONFIG_OMAP3_*_DDR
This patch removes the unused definitions:
CONFIG_OMAP3_MICRON_DDR
CONFIG_OMAP3_NUMONYX_DDR
CONFIG_OMAP3_INFINEON_DDR

Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
2012-01-16 08:40:10 +01:00
Thomas Weber
81dcf8bb11 ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
This patch removes the definition of stack sizes for
irq and fiq if the CONFIG_USE_IRQ is undefined before.

Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
2011-12-06 23:59:35 +01:00
Thomas Weber
0997561de9 ARM: OMAP3: Remove unused define SDRC_R_C_B
This patch removes the unused definition of SDRC_R_C_B
from the config files.

Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Acked-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:35 +01:00
Thomas Weber
8152c6f6f5 ARM: OMAP3: Remove unused define CONFIG_OMAP3430
This patch removes the CONFIG_OMAP3430, because it is unused.

Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
2011-12-06 23:59:35 +01:00
Aneesh V
8e40852f0d omap: fix cache line size for omap3/omap4 boards
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:34 +01:00
Tom Rini
d6906cb812 OMAP3: Zoom1: Use generic MMC driver
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver.  This patch is based on the work done for Beagle, etc.

Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:17 +02:00
Vaibhav Hiremath
f62b1257f2 OMAP3/4: Increase console I/O buffer size
Increase the console I/O buffer size (SYS_CBSIZE) to 512 (from 256)
required especially for bootargs string, as multiple options
(e.g Video settings) are passed to the kernel through bootargs.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:17 +02:00
Christopher Harvey
75f980bdb3 Removed unused define, CONFIG_ARMV7.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
2011-08-04 12:49:37 +02:00
Michael Jones
2cc195e0a5 Remove remnants of obsolete CONFIG_SYS_GBL_DATA_SIZE comments
commit 25ddd1fb0a left remnants of
many comments about CONFIG_SYS_GBL_DATA_SIZE.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
2011-05-12 23:04:55 +02:00
Grant Likely
2fa8ca98c3 Add CONFIG_OF_LIBFDT to more boards.
The following boards gain device tree support with this patch:

ca9x4_ct_vxp - Versatile Express

i.mx5 boards:
efikamx
mx51evk
mx53evk

OMAP boards:
devkit8000
igep0020
igep0030
omap3_overo
omap3_pandora
omap4_sdp3430
omap3_zoom1
omap3_zoom2
omap4_panda
omap4_sdp4430

Tegra boards:
Harmony

Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-28 14:44:17 +02:00
Luca Ceresoli
6cbec7b3ba ARMV7: OMAP3: Cleanup extern variables in mem.c
Removed boot_flash_* extern variables.
boot_flash_type was totally unused. The other ones were actually constants, so
they have been replaced with #defines in the board config files.

Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-04-27 19:38:10 +02:00
Dirk Behme
25435c6cce OMAP3: Zoom1: Fix ARM relocation support
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-30 11:10:45 -05:00
Grazvydas Ignotas
8b6724aa5a OMAP3: remove unused config macros
Most OMAP3 boards have various flash related macros in their configs
that are either not referenced anywhere in the code or are used by
drivers that are not enabled. Remove them.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-19 16:28:44 -05:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Steve Sakoman
f56348af5d ARM: Rename arch/arm/cpu/arm_cortexa8 to armv7
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9

Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.

The two architectures are similar enough that substantial code can be shared.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 19:59:55 -04:00
Vaibhav Hiremath
cae377b59a omap3: Consolidate SDRC related operations
Consolidated SDRC related functions into one file - sdrc.c

And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08 10:07:18 -05:00
Tom Rix
632e1d9014 OMAP3 Move declaration of gpmc_cfg.
Every omap3 board config file declared the global variable gpmc_cfg.
This changes moves the declaration to a better location in the
arch dependent header file cpu.h.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-02-12 12:31:53 -06:00
Robert P. J. Day
1270ec13d4 Remove superfluous uses of V_PROMPT macro.
A number of config files define the V_PROMPT macro for the
command-line prompt, only to immediately use that macro to define
CONFIG_SYS_PROMPT, making V_PROMPT entirely superfluous.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2010-01-04 08:48:16 -06:00
Tom Rix
05be5a60e9 OMAP3 zoom1 Add usbtty configuration
The primary console of zoom1 is the serial out from the jumpers
accessed by removing the back panel.

A secondary console is to use the usbtty.  The user can set this
manually by doing

setenv stdout usbtty; setenv stdin usbtty; setenv stderr usbtty
saveenv

usbtty will be usable by accessing the /dev/ttyACM0 on a linux host.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-12-20 12:50:53 +01:00
Heiko Schocher
4b142febff common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-08 22:14:07 +01:00
Nishanth Menon
30563a04bf OMAP3:SDRC: introduce DDR types
Micron DDR timings based on:
http://www.sakoman.net/cgi-bin/gitweb.cgi?p=x-load-omap3.git;a=blob;f=include/asm/arch-omap3/mem.h;h=e6fbfe3947f5d0d85fea776e30821d4017316d86;hb=HEAD

Introduce Micron DDR timings and provide
CONFIG_OMAP3_INFINEON_DDR and CONFIG_OMAP3_MICRON_DDR config
options to allow for platform files to setup their timings as
per the type of DDR selected

Reported-by: Steve Sakoman in http://www.nabble.com/forum/Permalink.jtp?root=25779518&post=25959734&page=y

Signed-off-by: Nishanth Menon <nm@ti.com>
2009-11-27 16:26:16 -06:00
Sandeep Paulraj
9c44ddccb6 TI: OMAP3: Remove SZ_xx references
This patch removes dependency on the sizes.h header file
and removes all references to SZ_xx.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-10-18 16:52:52 -05:00
Tom Rix
0297ec7e2a TI OMAP3 Use arm init sequence to initialize i2c
This changes fixes an early i2c error.

It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.

While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.

Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.

Run tested on Beagle.
Compile tested on the omap3's

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2009-10-13 06:17:37 -05:00
Dirk Behme
97a099eaa4 omap3: remove typedefs for configuration structs
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-08-08 11:33:23 +02:00
Matthias Ludwig
187af954cf omap3: embedd gpmc_cs into gpmc config struct
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html

Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
2009-08-07 23:31:51 +02:00
Tom Rix
2c15513010 OMAP3 Move twl4030 power and led functions
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.

power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.

The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.

The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c  The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED

The directory board/omap3/common was removed because power_init_r
was the only function in it.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-29 09:57:30 +02:00
Tom Rix
cd7826359e TWL4030 Add power reset button
The Zoom2 power reset button is on the top right side of the
main board.  Press and hold for about to 8 seconds to completely
reset the board.

Some of the beta boards have a hardware problem that prevents
using this feature.  If is difficult to further characterize the
boards that fail.  So disable resetting for all beta boards.

The Zoom1 reset button is the red circle on the top right,
front of the board.  Press and hold the button for 8 seconds to
completely reset the board.

After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.

The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.

The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
2009-07-28 08:56:31 +02:00
Wolfgang Denk
2eb99ca802 NAND: Part 2: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.

This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-18 21:56:15 +02:00
Tom Rix
daea928829 ZOOM1 Remove more legacy NAND defines.
These legacy NAND defines are no longer needed by this target.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:49 +02:00
Manikandan Pillai
d3a513c23b OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Manikandan Pillai <mani.pillai@ti.com>
2009-04-30 23:56:01 +02:00
Sanjeev Premi
6a6b62e3aa OMAP3: Use functions print_cpuinfo() and checkboard()
Use the functions print_cpuinfo() and checkboard() to
display the cpu and board specific information.

These functions reuse content from the existing function
display_board_info() - which has been removed.

Also, updated the existig OMAP3 configurations to
define:
 - CONFIG_DISPLAY_CPUINFO
 - CONFIG_DISPLAY_BOARDINFO

Signed-off-by: Sanjeev Premi <premi@ti.com>
2009-04-29 21:11:32 +02:00