Commit graph

16 commits

Author SHA1 Message Date
Heiko Schocher
d14c6335bc arm, am33xx: Enable CONFIG_SYS_GENERIC_BOARD for siemens boards
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Tested-by: Samuel Egli <samuel.egli@siemens.com>
2014-05-23 19:40:38 -04:00
Egli, Samuel
66c45faefb siemens: cosmetic: rename project_dir
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-05-13 19:43:00 -04:00
Egli, Samuel
84112b5171 siemens: change LED indication in DFU mode
In order to have the same LED indication like in another product
when ready for updating, enable only red led and disable status
LED when entering DFU mode.

The status LED is only switched off when defined in board file.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2014-05-13 19:43:00 -04:00
Heiko Schocher
401341d621 am335x, dfu: add DFU_MANIFEST_POLL_TIMEOUT to the siemens boards
as the siemens boards use dfu for updating a nand ubi partition
add DFU_MANIFEST_POLL_TIMEOUT to them, so dfu host waits after
complete transfer of the new image for DFU_MANIFEST_POLL_TIMEOUT
ms before sending again an usb request. So the board have enough
time to erase rest of the nand sectors.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-03-23 02:20:10 +01:00
pekon gupta
a7e36fc95f mtd: nand: omap: remove unused #defines from common omap_gpmc.h
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
	- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
	- GPMC_NAND_ECC_LP_x8_LAYOUT  (for large page x8 NAND)
	- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
	- GPMC_NAND_ECC_SP_x8_LAYOUT  (for small page x8 NAND)

2) removes unused #defines in common omap_gpmc.h depending on above configs

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
Heiko Schocher
dc427369b1 am335x, siemens boards: adapt default environment setting
commit 16297cfb2a
Author: Mateusz Zalega <m.zalega@samsung.com>
Date:   Fri Oct 4 19:22:26 2013 +0200

    usb: new board-specific USB init interface

introduced a new parameter to the dfu command. Adapt the default environment
for the siemens boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
2013-12-12 14:54:22 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Stefan Roese
9167fc81b3 arm: am335x: Add DT (FDT) support to Siemens boards
Enable FDT support for all Siemens AM335x boards. To support
newer Linux kernels with DT booting.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher<hs@denx.de>
2013-12-04 11:41:13 -05:00
Tom Rini
faca8ff55f Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-11-25 10:42:13 -05:00
pekon gupta
3f719069c8 mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.

1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
   other ecc-schemes also supported in hardware. like;
 - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
   the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
   software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
 - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
   supports BCH16 ecc-scheme also.

2) Different platforms use different CONFIG_xx to select ecc-schemes, which
   adds confusion for user while migrating platforms.
 - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
    8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
    whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
    and BCH16 (in future).
 - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
    correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
 - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library

Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
pekon gupta
beba5f04f2 mtd: nand: omap: make am33xx/elm.c as common driver for all OMAPx and AMxxxx platforms
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
	and include in all board configs using AM33xx SoC platform.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Samuel Egli
56eb3da43f arm, am335x: update for the siemens boards
- dxr2: define unused pins as input
- do not enable RTC32K OSC on dxr2 board
- update default environment
  - add splashpos=m,m to default environment, so splash screen is always
    centered.
  - adapt environment for bootcount feature
  - add altbootcmd to default environment
- rut: SPL add early reset pulse for eth-phy, maXTouch and display
- rut: display timing aenderungen
- siemens boards: adapt for background color = white
- add boutcount feature for the siemens boards
  store the bootcount in the environment, as we have no softreset
  save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV
  bootcount driver.
- change spi mode from 3 to 0 for the lcd init
- add gpio pin for lcd reset with state 0 and add mdelay
- siemens boards: use own USB id's
- add dfu serial and device number for siemens boards
  Add for the siemens boards the possibility to define in dfu mode,
  the iSerialNumber and the bcdDevice fields in the USB Device
  descriptor.
- fix upgrade mechanism based on bootcount
  Correct location of saveenv and remove not active variable.

  Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to
  reboot board in case of empty kernel partition. Without
  these defines an empty kernel partition leads to an
  abort of boot process and one remains in u-boot prompt.

- general cleanup of dxr2, pxm2 and rut boards
  all:
   * Remove net boot from bootcmd
     Ping can cause a crash on boards without ethernet phy.
     net_nfs command is used only for development

   * Add reset at the end of bootcmd
     In order to have an immediate reset of the boot when bootcmd
     fails, add reset at the end of bootcmd.

  rut:
   * add nand_img_size

  dxr2:
   * update nand_img_size

   * ddr3 timings updated with iocontrol property that can be
     modified via eeprom. New default parameters from software
     leveling with draco ES2.

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Pascal Bach <pascal.bach@siemens.com>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Michel <matthias.michel@siemens.com>
Cc: Tom Rini <trini@ti.com>
2013-11-12 09:53:59 -05:00
Rob Herring
f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00
Tom Rini
901ce27c6f siemens-am33x-common.h: Always build CONFIG_OMAP_GPIO support
The MMC driver relies on this block now.

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28 12:01:30 -04:00
Heiko Schocher
c0dcece7d9 arm, am335x: add support for 3 siemens boards
add support for the am335x based boards from siemens:

dxr2:
  - DDR3 128MiB
  - NAND 256MiB
  - Ethernet with external Switch SMSC LAN9303
  - no PMIC
  - internal Watchdog
  - DFU support

pxm2:
  - DDR2 512 MiB
  - NAND 1024 MiB
  - PMIC
  - PHY atheros ar803x
  - USB Host
  - internal Watchdog
  - DFU support

rut:
  - DDR3 256 MiB
  - NAND 256 MiB
  - PMIC
  - PHY natsemi dp83630
  - external Watchdog
  - DFU support

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Pascal Bach <pascal.bach@siemens.com>
Cc: Tom Rini <trini@ti.com>
2013-08-28 11:44:59 -04:00