Commit graph

28 commits

Author SHA1 Message Date
Lokesh Vutla
7b92252370 ARM: DRA: Enable VTT regulator
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-25 10:48:13 -04:00
pekon gupta
9352697aa0 board/ti/dra7xx: add support for parallel NOR
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.

As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
     SW5.1 (NAND_BOOTn) = OFF (logic-1)
     SW5.2 (NOR_BOOTn)  = ON  (logic-0) /* Active-low */
     SW5.3 (eMMC_BOOTn) = OFF (logic-1)
     SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations:
     SW3.1 (SYSBOOT[ 8])= ON  (logic-1) /* selects SYS_CLK1 speed */
     SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
     SW3.3 (SYSBOOT[10])= ON  (logic-1) /* wait-pin monitoring = enabled */
     SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
     SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
     SW3.6 (SYSBOOT[13])= ON  (logic-1) /* device bus-width: 1(x16) */
     SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
     SW3.8 (SYSBOOT[15])= ON  (logic-1) /* reserved */

Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
2014-08-25 10:48:12 -04:00
pekon gupta
54a97d2849 board/ti/dra7xx: add support for parallel NAND
This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by multiple devices, so in addition to this patch
following board settings are required for NAND device detection [1]:

  SW5.9 (GPMC_WPN)   = OFF (logic-1)
  SW5.1 (NAND_BOOTn) = ON  (logic-0) /* Active-low */
  SW5.2 (NOR_BOOTn)  = OFF (logic-1)
  SW5.3 (eMMC_BOOTn) = OFF (logic-1)
  SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations
  SW2.1 (SYSBOOT[0]) = ON  (logic-1) /* selects NAND Boot */
  SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */
  SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */
  SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */
  SW2.5 (SYSBOOT[4]) = ON  (logic-1) /* selects NAND Boot */
  SW2.6 (SYSBOOT[5]) = ON  (logic-1) /* selects NAND Boot */
  SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */
  SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */

  SW3.1 (SYSBOOT[ 8])= ON  (logic-1) /* selects SYS_CLK1 speed */
  SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
  SW3.3 (SYSBOOT[10])= ON  (logic-1) /* wait-pin monitoring = enabled */
  SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */
  SW3.5 (SYSBOOT[12])= ON  (logic-1) /* device type: Addr/Data Muxed */
  SW3.6 (SYSBOOT[13])= ON  (logic-1) /* device bus-width: 1(x16) */
  SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
  SW3.8 (SYSBOOT[15])= ON  (logic-1) /* reserved */

Following changes are required in board.cfg to enable NAND on J6-EVM:
2014-08-25 10:48:12 -04:00
Tom Rini
79b079f35c dra7xx_evm: Add QSPI_4 support, qspiboot build target
We previously only supported QSPI_1 (single) support.  Add QSPI_4 (quad)
read support as well.  This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value.  We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment.  When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:37 -04:00
Tom Rini
2737f0112b TI:omap5: Move CONFIG_ENV_SIZE to board config files
The size of the environment depends on the backing store, move this to
the board config files.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Mugunthan V N
9c653aad16 drivers: net: cpsw: add support to have phy address from cpsw platform data
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 09:41:53 -05:00
Tom Rini
2efa79ae00 dra7xx_evm: Enable GPT commands
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 14:03:44 -05:00
Tom Rini
c4d376fd1c Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-17 14:22:02 -05:00
Tom Rini
b818d9ab8d dra7xx_evm: Add CONFIG_SUPPORT_EMMC_BOOT, document usage
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 18:17:49 +02:00
Enric Balletbò i Serra
3d657a05a9 ARM: OMAP5: Rename to ti_omap5_common.h
Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap5_common.h to ti_omap5_common.h.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by:  Lokesh Vutla <lokeshvutla@ti.com>
2014-01-24 11:38:39 -05:00
Poddar, Sourav
2c57b03bab config: dra7_evm: Add Bank Address Register(BAR) config
Add config to support bank address register.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Yebio Mesfin <ymesfin@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2013-12-19 12:23:21 +05:30
Roger Quadros
21914ee62a ARM: dra7_evm: Add SATA support
The evm has a SATA port. Enable SATA configuration and
inititialize the SATA controller.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2013-12-04 08:12:36 -05:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Minal Shah
a13cbf5f20 dra7xx_evm: Enabled UART-boot mode and add dra7xx_evm_uart3 build
UART booting is supported on this SoC, but via UART3 rather than UART1.
Because of this we must change the board to use UART3 for all console
access (only one UART is exposed on this board and a slight HW mod is
required to switch UARTs).

Signed-off-by: Minal Shah <minal.shah@ti.com>
[trini: Make apply to mainline, reword commit]
Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:56:00 -04:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Matt Porter
247cdf0413 dra7xx_evm: add SPL API, QSPI, and serial flash support
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:52 +05:30
Lokesh Vutla
d3d33daf11 ARM: DRA7: Enable saveenv command
dra7xx_evm has eMMC and the default environment can be stored in it.
So enabling saveenv command and the configs to store environment in eMMC.

Tested on DRA752 ES1.0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-09-20 16:57:40 -04:00
Tom Rini
457bb50560 dra7xx_evm: Re-order and comment the networking related config options
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-28 11:44:59 -04:00
Tom Rini
a801757480 TI:omap5/dra7xx: Convert to ti_armv7_common.h
Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly.  The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:36 -04:00
Mugunthan V N
c9be62caba ARM: DRA7xx: Enable CPSW Ethernet support
Enabling CPSW Ethernet support in DRA7xx EVM.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Dan Murphy
45dbbf29bb arm: dra7xx: Update the EXTRA_ENV_SETTINGS
Update the EXTRA_ENV_SETTING for the dra7xx.
The console needs to be set to ttyO0 and the
findfdt needs to be updated to load the
dra7xx-evm.dtb file.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-06-18 10:43:29 -04:00
Lokesh Vutla
97405d843e ARM: DRA7xx: clocks: Update PLL values
Update PLL values.
SYS_CLKSEL value for 20MHz is changed to 2. In other platforms
SYS_CLKSEL value 2 represents reserved. But in sys_clk array
ind 1 is used for 13Mhz. Since other platforms are not using
13Mhz, reusing index 1 for 20MHz.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10 08:43:10 -04:00
Sricharan R
378bd1fb4e ARM: DRA7xx: Change the Debug UART to UART1
Serial UART is connected to UART1. So add the change
for the same.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
4de28d7921 ARM: DRA7xx: Add control id code for DRA7xx
The registers that are used for device identification
are changed from OMAP5 to DRA7xx.
Using the correct registers for DRA7xx.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-06-10 08:43:09 -04:00
Tom Rini
9552ee3ea9 omap5_uevm.h: Move uEVM-specific choices to omap5_uevm.h
The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there.  Other platforms may not, so
move this choice to the EVM config.  In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.

Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-04-08 11:40:56 -04:00
Lokesh Vutla
3ef5ebeb86 arm: dra7xx: Add dra7xx_evm build support
Adding the build support for dra7xx_evm.
Reusing omap5_evm.h config by moving it to omap5_common.h

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
2013-03-11 11:39:57 -04:00