Commit graph

4 commits

Author SHA1 Message Date
Stephen Warren
39446bcefa ARM: tegra: enable DFU too
Enable DFU protocol support (via the "dfu" command) on Tegra boards where
USB device/gadget mode is enabled.

Note that for DFU to operate correctly on Tegra, we still need some DFU
fixes/enhancements that are going through the DFU -> USB trees. However,
the code builds just fine without those changes, and applying this patch
now will allow both sets of patches to meet in the main U-Boot tree much
more quickly.

In order to run test/dfu/dfu_gadget_test.sh, you would need to add the
following to the board configuration:

CONFIG_EXT4_WRITE
CONFIG_CMD_EXT4_WRITE

However, I haven't enabled those here, since I believe the main use-case
for DFU on Tegra is raw flash writing, rather than filesystem access, so
we don't need the additional code-size hit. However, I could be persuaded
otherwise! We should probably add a separate test script for raw flash
access.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-08-18 16:57:03 -07:00
Stephen Warren
e6607cffef ARM: tegra: enable USB device mode and UMS on some boards
For each of Jetson TK1, Venice2, and Beaver:

- Enable the first USB controller in DT, and describe its configuration.

- Enable USB device/gadget support. This allows the user to type e.g.
  "ums 0 mmc 0" at the command-line to cause U-Boot to act a USB device
  implementing the USB Mass Storage protocol, and expose MMC device 0
  that way.

This allows a host PC to mount the Tegra device's MMC, partition it, and
install a filesystem on it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-06-05 11:25:54 -07:00
Alexey Brodkin
1ace402239 sizes.h - consolidate for all architectures
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 12:15:01 -05:00
Tom Warren
f7dc4ac37c ARM: tegra: add Venice2 (Tegra124) board
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC
files. PMIC init will be moved to pmic_common_init later.

This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display
and WB/LP0 are not supported yet.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-02-03 09:46:47 -07:00