It is useful to be able to try a range of
possible phy addresses to connect.
Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Only the hardware ethernet registers are needed
for this function, so don't pass the more general
structure. I'm trying to separate MII and fec.
This also fixes MX28 fec_mii_setspeed use on secondary ethernet port
This was found by inspection of the code and should be
checked on real hardware.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
It is more logical to test for CONFIG_FEC_MXC_PHYADDR
to determine whether to define the function fecmxc_initialize.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
SH7752 has two fast ethernet controllers and two gigabit ethernet
controllers. It is similar to SH7757.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marvell 88E1118R has different uid then 88E1118.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Andy Fleming <afleming@freescale.com>
CC: Zang Roy-R61911 <tie-fei.zang@freescale.com>
CC: Kumar Gala <galak@kernel.crashing.org>
In e1000e driver, Rx descriptor queue is used such that hardware can add only
one descriptor at a time. So the WTHRESH granularity in RXDCTL should be set
to single descriptor. This would ensure that every time controller fills a Rx
descriptor, it is flushed to host memory. Earlier this granularity was in
cache line units i.e 2 descriptors. This leads to controller always waiting
for 2 descriptors before flushing them out. But since not more than one Rx BD
is actually available , the accumulation condition never gets hit.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Vakul Garg <vakul@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
The P5040DS reference board (a.k.a "Superhydra") is an enhanced version of
P3041DS/P5020DS ("Hydra") reference board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
phy.c:46:5: warning: symbol 'genphy_config_advert' was not declared. Should it be static?
phy.c:121:5: warning: symbol 'genphy_setup_forced' was not declared. Should it be static?
phy.c:468:5: warning: symbol 'phy_probe' was not declared. Should it be static?
phy.c:491:19: warning: symbol 'get_phy_driver' was not declared. Should it be static?
phy.c:508:19: warning: symbol 'phy_device_create' was not declared. Should it be static?
phy.c:552:5: warning: symbol 'get_phy_id' was not declared. Should it be static?
phy.c:584:19: warning: symbol 'get_phy_device' was not declared. Should it be sta
vitesse.c:126:5: warning: symbol 'vsc8601_config' was not declared. Should it be static?
vsc7385.c:33:5: warning: symbol 'vsc7385_upload_firmware' was not declared. Should it be static?
tgec_phy.c:33:5: warning: symbol 'tgec_mdio_write' was not declared. Should it be static?
tgec_phy.c:75:5: warning: symbol 'tgec_mdio_read' was not declared. Should it be static?
tgec_phy.c:117:5: warning: symbol 'tgec_mdio_reset' was not declared. Should it be static?
eth.c:48:6: warning: symbol 'dtsec_configure_serdes' was not declared. Should it be static?
p4080.c:26:5: warning: symbol 'port_to_devdisr' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
bootp.c:44:14: warning: symbol 'dhcp_state' was not declared. Should it be static?
bootp.c:45:15: warning: symbol 'dhcp_leasetime' was not declared. Should it be static?
bootp.c:46:10: warning: symbol 'NetDHCPServerIP' was not declared. Should it be static?
arp.c:30:17: warning: symbol 'NetArpWaitReplyIP' was not declared. Should it be static?
arp.c:37:16: warning: symbol 'NetArpTxPacket' was not declared. Should it be static?
arp.c:38:17: warning: symbol 'NetArpPacketBuf' was not declared. Should it be static?
atheros.c:33:19: warning: symbol 'AR8021_driver' was not declared. Should it be static?
net.c:183:7: warning: symbol 'PktBuf' was not declared. Should it be static?
net.c:159:21: warning: symbol 'net_state' was not declared. Should it be static?
ping.c:73:6: warning: symbol 'ping_start' was not declared. Should it be static?
ping.c:82:13: warning: symbol 'ping_receive' was not declared. Should it be static?
tftp.c:53:7: warning: symbol 'TftpRRQTimeoutMSecs' was not declared. Should it be static?
tftp.c:54:5: warning: symbol 'TftpRRQTimeoutCountMax' was not declared. Should it be static?
eth.c:125:19: warning: symbol 'eth_current' was not declared. Should it be static?
Note: in the ping.c fix, commit a36b12f95a
"net: Move PING out of net.c" mistakenly carried the ifdef CMD_PING
clause from when it was necessary to avoid warnings when it was embedded
in net.c.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
TBI PHY address (TBIPA) register is set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c, and
it is supposed to set TBIPA on FM1@DTSEC1 in case of FM1@DTSEC1
isn't used directly, which provides MDIO for other ports. So
following code is wrong in case of FM2, which has a different
mac base.
struct dtsec *regs = (struct dtsec *)fm_eth->mac->base;
/* Assign a Physical address to the TBI */
out_be32(®s->tbipa, CONFIG_SYS_TBIPA_VALUE);
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale B4860 and variant SoCs. Features of B4860 are
(incomplete list):
Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
clusters-each core runs up to 1.2 GHz, with an architecture highly
optimized for wireless base station applications
Four dual-thread e6500 Power Architecture processors organized in one
cluster-each core runs up to 1.8 GHz
Two DDR3/3L controllers for high-speed, industry-standard memory interface
each runs at up to 1866.67 MHz
MAPLE-B3 hardware acceleration-for forward error correction schemes
including Turbo or Viterbi decoding, Turbo encoding and rate matching,
MIMO MMSE equalization scheme, matrix operations, CRC insertion and
check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration,
and UMTS chip rate acceleration
CoreNet fabric that fully supports coherency using MESI protocol between
the e6500 cores, SC3900 FVP cores, memories and external interfaces.
CoreNet fabric interconnect runs at 667 MHz and supports coherent and
non-coherent out of order transactions with prioritization and
bandwidth allocation amongst CoreNet endpoints.
Data Path Acceleration Architecture, which includes the following:
Frame Manager (FMan), which supports in-line packet parsing and general
classification to enable policing and QoS-based packet distribution
Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
of queue management, task management, load distribution, flow ordering,
buffer management, and allocation tasks from the cores
Security engine (SEC 5.3)-crypto-acceleration for protocols such as
IPsec, SSL, and 802.16
RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
outbound). Supports types 5, 6 (outbound only)
Large internal cache memory with snooping and stashing capabilities for
bandwidth saving and high utilization of processor elements. The
9856-Kbyte internal memory space includes the following:
32 Kbyte L1 ICache per e6500/SC3900 core
32 Kbyte L1 DCache per e6500/SC3900 core
2048 Kbyte unified L2 cache for each SC3900 FVP cluster
2048 Kbyte unified L2 cache for the e6500 cluster
Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
Sixteen 10-GHz SerDes lanes serving:
Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total
of up to 8 lanes
Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-
less antenna connection
Two 10-Gbit Ethernet controllers (10GEC)
Six 1G/2.5-Gbit Ethernet controllers for network communications
PCI Express controller
Debug (Aurora)
Two OCeaN DMAs
Various system peripherals
182 32-bit timers
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):
12 dual-threaded e6500 cores built on Power Architecture® technology
Arranged as clusters of four cores sharing a 2 MB L2 cache.
Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
v2.06-compliant)
Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
CoreNet fabric supporting coherent and non-coherent transactions with
prioritization and bandwidth allocation amongst CoreNet end-points
1.6 Tbps coherent read bandwidth
Queue Manager (QMan) fabric supporting packet-level queue management and
quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support
Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
the following functions:
Packet parsing, classification, and distribution (Frame Manager 1.1)
Queue management for scheduling, packet sequencing, and congestion
management (Queue Manager 1.1)
Hardware buffer management for buffer allocation and de-allocation
(BMan 1.1)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps
RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
Up to four 10 Gbps Ethernet MACs
Up to sixteen 1 Gbps Ethernet MACs
Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
Four PCI Express 2.0/3.0 controllers
Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
Type 11 messaging and Type 9 data streaming support
Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Four I2C controllers
Four 2-pin or two 4-pin UARTs
Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The following warning was produced, fix it:
mcfmii.c: In function 'mcffec_miiphy_write':
mcfmii.c:318:8: warning: variable 'rdreg' set but not used [-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: "Jin Zhengxiong-R64188" <R64188@freescale.com>
Cc: Jason Jin <jason.jin@freescale.com>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
The mechanism waiting for transmission to finish in fec_send() now
relies on the E-bit being cleared in the TX buffer descriptor. In
case of data cache being on, this means invalidation of data cache
above this TX buffer descriptor on each test for the E-bit being
cleared.
Apparently, there is another way to check if the transmission did
complete. This is by checking the TDAR bit in the X_DES_ACTIVE
register. Reading a register does not need any data cache invalidation,
which is beneficial.
Rework the sequence that wait for completion of the transmission so that
the TDAR bit is tested first and afterwards check the E-bit being clear.
This cuts down the number of cache invalidation calls to one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The FEC hardware sometimes errors out on data transfer and hangs in
the tightloop adjusted by this patch. So add timeout into the tightloop
to make such a hang recoverable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Align the address that's to be invalidated/flushed properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Do not pass unaligned RX buffer to the upper layers. The upper layer,
especially in the ARP case, recycles the buffer and passes it back into
the FEC, into it's TX path. With caches enabled, the FEC hangs on this
from time to time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
-VSC8662 is Dual Port 10/100/1000Base-T Phy,
100Base-FX/1000/Base-X Gigabit Ethernt Transceiver Phy.
-Its register set and features are similar to
other Vitesse Phys
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.
This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Device driver for Zynq Gem IP.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Check the incoming packets' source IP address... if ncip isn't set to a
broadcast address, only listen to the client at ncip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Refresh the netconsole settings from the env before each packet instead
of only on netconsole init.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Previously u-boot would initialize the network interface for every
network operation and then shut it down again. This makes sense for
most operations where the network in not known to be needed soon after
the operation is complete. In the case of netconsole, it will use the
network for every interaction with the shell or every printf. This
means that the network is being reinitialized very often. On many
devices, this intialization is very slow.
This patch checks for consecutive netconsole actions and leaves the
ethernet hardware initialized between them. It will still behave the
same old way for all other network operations and any time another
network operation happens between netconsole operations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Allow a board to configure a larger buffer for netconsole, but leave
the default.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
R8A7740 of rmobile has ethernet device, and this is same IP of
sh-ether. This support R8A7740 of rmobile.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Apply the following questionable adjustment to silence GCC.
armada100_fec.c: In function ‘armdfec_send’:
armada100_fec.c:589:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Support new CONFIG_OF_CONTROL option where device
probing is done based on device tree description.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
It is desirable to use different port numbers for sending and receiving
packets with netconsole in the case where you have more than one device
on the local subnet with netconsole enabled for broadcast. When they
use the same port for both, any output from one will look like input to
the other. This is typlically not desirable.
This patch allows the input and output ports to be specified separately
in the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
greth.c: In function ‘greth_recv’:
greth.c:507:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’ [-Wformat]
greth.c:507:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘unsigned int’ [-Wformat]
greth.c:541:6: warning: pointer targets in assignment differ in signedness [-Wpointer-sign]
greth.c: In function ‘greth_initialize’:
greth.c:623:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
greth.c:655:3: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
greth.c:684:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: u-boot-dm@lists.denx.de
* 'master' of git://git.denx.de/u-boot-avr32:
net:macb: add line break
avr32:portmux: fix setup for macb1
avr32: Remove redundant LDSCRIPT definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Without this patch we see annoying output like this:
---8<---
U-Boot> dhcp
macb1: PHY not foundmacb0: PHY present at 1
macb0: Starting autonegotiation...
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35
Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
CPSW is an on-chip ethernet switch that is found on various SoCs from Texas
Instruments. This patch adds a simple driver (based on the Linux driver) for
this hardware module.
This patch also adds support to clean and flush dcache during packet send
and receive.
Changes by Sandhya: Added support to clean and flush dcache during packet
send/receive and added timeouts.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
[Ilya: Cleaned cache handling, some style cleanup, some small
fixes, use of internal RAM for descriptors]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
These are not supported as individual build targets, but instead
are supported by another target.
The dead p4040 defines in particular had bitrotted significantly.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We have a dedicated function for setting the node status now, so use it.
Also improve a comment and fix the type of the phandle variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Function fm_info_get_phy_address() returns the PHY address for a given
Fman port. This is handy when the MDIO code needs to fixup the Ethernet
nodes in the device tree to point to PHY nodes for a specific PHY address.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second
Fman, so add the Fman and SerDes macros for that DTSEC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
SH7757 has 2 ETHERs and 2 GETHERs. This patch supports the SH7757's
GETHER. If CONFIG_SH_ETHER_USE_GETHER is defined using SH7757,
the driver handles the GETHER.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The previous code had many similar definitions in each CPU.
This patch borrows from the sh_eth driver of Linux kernel.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
At the moment, the driver supports the following CPUs:
- GETHER (Gigabit Ethernet) : SH7763, SH7734
- ETHER (Fast Ethernet) : SH7724, SH7757
And the driver had the following "#if":
#if defined(CONFIG_CPU_SH7763) || defined(CONFIG_CPU_SH7734)
#if !defined(CONFIG_CPU_SH7757) && !defined(CONFIG_CPU_SH7724)
- Those are for GETHER
#if defined(CONFIG_CPU_SH7724) || defined(CONFIG_CPU_SH7757)
- This is for ETHER
So, for clean up the code, this patch adds SH_ETH_TYPE_GETHER and
SH_ETH_TYPE_ETHER. And then, the patch modifies the above "#if".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The SH7757's ETHER can work using the SH7724's setting. So, the patch
modifies it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The MDC signal is available on all xMII (i.e. 'not 7-wire') interfaces, so
mii_speed has to be set for all these interfaces, and not only for MII.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
At least on i.MX25, the RMII mode did not work, which is fixed by this patch.
The MII_MODE bit of the FEC RCR register means xMII, i.e. 'not 7-wire', so set
it accordingly.
According to the xMII and 7-wire (aka GPSI) standards, full duplex should be
available on xMII, but not on 7-wire, so set FCE accordingly. The FEC may
support full duplex for 7-wire too, but the reference manual does not say that,
so avoid an invalid assumption. Actually, the choice between half and full
duplex also depends on the endpoint/switch/repeater configuration, so a config
option could be added for that, but there has been no need for it so far.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Now that common code doesn't declare these as volatile, we don't need to
either anymore. This fixes the build warning:
bfin_mac.c: In function 'bfin_EMAC_recv':
bfin_mac.c:193:23: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'next' of git://git.denx.de/u-boot-net:
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
This commit is an add-on to f6c4191f. There are a few registers where
consecutive writes to the same location should be avoided or have a delay.
According to Synopsys, here is a list of the registers and bit(s) where
consecutive writes should be avoided or a delay is required:
DMA Registers:
Register 0 Bit 7
Register 6 All bits except for 24, 16-13, 2-1.
GMAC Registers:
Registers 0-3 All bits
Registers 6-7 All bits
Register 10 All bits
Register 11 All bits except for 5-6.
Registers 16-47 All bits
Register 48 All bits except for 18-16, 14.
Register 448 Bit 4.
Register 459 Bits 0-3.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Matthew Gerlach <mgerlach@altera.com>
Acked-by: Amit Virdi <amit.virdi@st.com>
Micrel accidentally used the same part number
for the KS8721 and KSZ9021. So, both cannot be
in the same build of u-boot. Add a config option
to handle this.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Now that phy_startup() can return an actual error code, check for that error
code and abort network initialization if the PHY fails.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamamatsu <nobuhiro.iwamatsu.yj@renesas.com> (sh_eth part)
Acked-by: Stephan Linz <linz@li-pro.net> (Xilinx part, xilinx_axi_emac and xilinx_ll_temac)
Reviewed-by: Marek Vasut <marex@denx.de> (FEC part)
phy_startup() calls the PHY driver's startup function, but it ignores the
return code from that function, and so it never returns any failures.
Signed-off-by: Timur Tabi <timur@freescale.com>
When support sh7734 of sh-ether, ECSIPR_BRCRXIP and other were removed.
Therefore SH7757 and SH7724 can not build. This revise this probelem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
This patch adds the following changes to designware ethernet driver
found on the ST SPEAr SoC:
- Don't init MAC & PHY upon startup. This causes a delay, waiting for
the auto negotiation to complete. And we don't want this delay to
always happen. Especially not on platforms where ethernet is not
used at all (e.g. booting via flash).
Instead postpone the MAC / PHY configuration to the stage, where
ethernet is first used.
- Add possibility for board specific PHY init code. This is needed
for example on the X600 board, where the Vitesse PHY needs to be
configured for GMII mode.
This board specific PHY init is done via the function
designware_board_phy_init(). And this driver now adds a weak default
which can be overridden by board code.
- Use common functions miiphy_speed() & miiphy_duplex() to read
link status from PHY.
- Print status and progress of auto negotiation.
- Print link status (speed, dupex) upon first usage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
Few Designware peripheral registers need to be modified based on the
ethernet interface selected by the board. This patch supports interface
information in ethernet driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On DA850/OMAP-L138 it was observed that in RMII mode,
auto negotiation was not performed. This patch enables
auto negotiation in RMII mode. Without this patch, EMAC
initialization takes more time and sometimes tftp fails
in RMII mode.
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
SH7734 support GMII. This add register infomation and the function
which enable GMII.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
SH7734 has one channel ethernet device.
This support 10/100/1000Base, and RMII/MII/GMII.
And this has the same structure as SH7763.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Add several levels of DEBUG prints so that you can limit the noise to
the severety of your problem.
DEBUG_LL_STATE = Link local state machine changes
DEBUG_DEV_PKT = Packets or info directed to the device
DEBUG_NET_PKT = Packets on info on the network at large
DEBUG_INT_STATE = Internal network state changes
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Call a built-in dummy if none is registered... don't require
protocols to register a handler (eliminating dummies)
NetConsole now uses the ARP handler when waiting on arp
(instead of needing a #define hack in arp.c)
Clear handlers at the end of net loop
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Rename IP header related things to IP_UDP. The existing definition
of IP_t includes UDP header, so name it to accurately describe the
structure.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
These are all the files which use the API incorrectly but did not get
built using MAKEALL -a powerpc|arm. I have no compiler for them, but
the remaining issues should be far less than without this patch.
Any outstanding issues are left to the maintainers of boards that use
these drivers.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
rtl8169.c: In function 'rtl8169_initialize':
rtl8169.c:907:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
pcnet.c: In function 'pcnet_initialize':
pcnet.c:224:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
xilinx_axi_emac.c: In function 'xilinx_axiemac_initialize':
xilinx_axi_emac.c:646: warning: assignment from incompatible pointer type
Signed-off-by: Stephan Linz <linz@li-pro.net>
Fix this:
xilinx_emaclite.c: In function 'xilinx_emaclite_initialize':
xilinx_emaclite.c:371: warning: assignment from incompatible pointer type
Signed-off-by: Stephan Linz <linz@li-pro.net>
Fix this:
xilinx_ll_temac.c: In function 'xilinx_ll_temac_initialize':
xilinx_ll_temac.c:332: warning: assignment from incompatible pointer type
xilinx_ll_temac.c:340: warning: assignment from incompatible pointer type
Signed-off-by: Stephan Linz <linz@li-pro.net>
Fix this:
uli526x.c: In function 'uli526x_initialize':
uli526x.c:243:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
tsi108_eth.c: In function 'tsi108_eth_initialize':
tsi108_eth.c:745:13: warning: assignment from incompatible pointer type
tsi108_eth.c: In function 'tsi108_eth_recv':
tsi108_eth.c:989:4: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
rtl8139.c: In function 'rtl8139_initialize':
rtl8139.c:234:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ns8382x.c: In function 'ns8382x_initialize':
ns8382x.c:352:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
natsemi.c: In function 'natsemi_initialize':
natsemi.c:338:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
eth.c: In function 'fm_eth_initialize':
eth.c:651:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
e1000.c: In function 'e1000_initialize':
e1000.c:5264:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
smc91111.c: In function 'smc91111_initialize':
smc91111.c:1363:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
macb.c: In function 'macb_eth_initialize':
macb.c:564:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
lan91c96.c: In function 'lan91c96_initialize':
lan91c96.c:811:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
ks8695eth.c: In function 'ks8695_eth_initialize':
ks8695eth.c:236:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
ftmac100.c: In function 'ftmac100_initialize':
ftmac100.c:266:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
fec_mxc.c: In function 'fec_probe':
fec_mxc.c:926:13: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
enc28j60.c: In function 'enc28j60_initialize':
enc28j60.c:967:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
eepro100.c: In function 'eepro100_initialize':
eepro100.c:464:13: warning: assignment from incompatible pointer type
eepro100.c: In function 'eepro100_recv':
eepro100.c:694:4: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
include/net.h:438:13: note: expected 'uchar *' but argument is of type 'volatile u8 *'
The use of a descriptor like this may mean DMA will update this at will
Beware this may be a source of trouble on some boards
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
dnet.c: In function 'dnet_eth_initialize':
dnet.c:380:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
dm9000x.c: In function 'dm9000_initialize':
dm9000x.c:636:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Fix this:
dc2114x.c: In function 'dc21x4x_initialize':
dc2114x.c:305:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Troy Kisky
Albert ARIBAUD
Yoshihiro Shimoda
Michal Simek
Ruchika Gupta
Yegor Yefremov
Timur Tabi
Kim Phillips
Marek Vasut
shaohui xie
Roy Zang
York Sun
Stefan Roese
Bastian Ruppert
Tom Rini
Priyanka Jain
Valentin Longchamp
Joe Hershberger
Nobuhiro Iwamatsu
Wolfgang Denk
Andreas Bießmann
Bo Shen
Cyril Chemparathy
Scott Wood
benoit.thebaudeau@advans
Mike Frysinger
Dinh Nguyen
Nobuhiro Iwamatsu
Vipin Kumar
Rajashekhara, Sudhakar
Stephan Linz