Commit graph

10 commits

Author SHA1 Message Date
Stefan Roese
81e33f4b65 arm: mvebu: Move SoC selection (A38X vs AXP) into Kconfig
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.

Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.

And CONFIG_DDR3 is removed, as its not referenced anywhere.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-01-14 14:08:59 +01:00
Anton Schubert
e863f7f051 arm: mvebu: add Armada XP SATA support
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.

Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-07-23 08:30:58 +02:00
Stefan Roese
3dc23f7852 arm: marvell: Move arch/kirkwood.h to arch/soc.h
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:20 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Gray Remlin
c08349e77c mvsata_ide.c: Correction of typo in comments
Signed-off-by: Gray Remlin <gryrmln@gmail.com>
2013-03-11 17:00:28 -04:00
Simon Guinot
2cb4fade0e mvsata: fix ide_preinit for missing disks
Consider that ide_preinit() succeed if at least one port is successfully
initialized. This allows to iniatialize IDE support on a board with two
SATA ports but a single hard disk available.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2011-12-06 23:59:30 +01:00
Michael Walle
70c55f5ab3 mvsata: issue hard reset on initialization
Before the actual initialization do a hard reset of the SATA port and the
connected device.

changes v1->v2:
 - add comment for udelay

Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-05-23 08:58:32 +02:00
Albert ARIBAUD
57b4bce996 Replace obsolete e-mail address
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-04-27 19:38:09 +02:00
Albert Aribaud
d3497138ff mvsata_ide: adjust port init sequence
mvsata_ide_initialize_port(): adjust init sequence (SStatus
should be checked only after all writes to SControl) and
return success/failure to ide_preinit().

Also, as some tests showed init durations in the hundreds
of us, raise the time-out to 01 ms to be on the safe side.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-10-13 09:35:54 +02:00
Albert Aribaud
39419ce589 ide: add mvsata_ide driver
This driver only provides initialization code; actual driving
is done by cmd_ide.c using the ATA compatibility mode of the
Marvell SATAHC controller.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-08-08 05:17:06 +05:30