Have CONFIG_ENV_ADDR be based on CONFIG_ENV_OFFSET rather than the other
way around so that we can use CONFIG_ENV_OFFSET during build. It also
avoids a little address duplication.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Info about the hardware can be found here:
http://www.dilnetpc.com/dnp0086.htm
Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Clean up the macro defintions used to enable DIU (video) support on the
MPC8610HPCD and the MPC5121ADS so that they look more like the P1022DS,
which is newer. Add software cursor support to all three boards.
Also document the CONFIG_FSL_DIU_FB in the README.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8572DS provides 2 USB ports with ULI1575. We enable USB storage
device support using PCI EHCI module.
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for 36-bit address map for NOR, SD, and SPI boot cfgs.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <priyanka.jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCA9557 is parallel I/O expansion device on I2C bus which stores various
board switch settings like NOR Flash-Bank selection, SD Data width.
On board:
switch SW5[6] is to select width for eSDHC
ON - 4-bit [Enable eSPI]
OFF - 8-bit [Disable eSPI]
switch SW4[8] is to select NOR Flash Bank for Booting
OFF - Primary Bank
ON - Secondary Bank
Read board switch settings on p1_p2_rdb and configure corresponding
eSDHC width.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using DDR as RAMBOOT base instead of L2SRAM for SDCard and SPI Flash
boot loaders because:
- P1_P2_RDB boards have soldered DDR so no need for SPD
- Also P102x has 256K L2 cache size so becomes a limiting factor for
size of image that could be loaded in SRAM mode and would require three
stage boot loader (TPL).
Changes done:
1. CONFIG_SYS_TEXT_BASE to 0x11000000
2. CONFIG_RESET_VECTOR_ADDRESS to 0x1107fffc
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are some differences between CoreNet (P2040, P3041, P5020, P4080)
and and non-CoreNet (P1017, P1023) based SoCs in what features exist and
the memory maps.
* Rename various immap defines to remove _CORENET_ if they are shared
* Added P1023/P1017 specific memory offsets
* Only setup LIODNs or LIODN related code on CORENET based SoCs
(features doesn't exist on P1023/P1017)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards
pretty much do the same thing. The only variations are in how many
controllers or DIMMs per controller exist. To make this work we
standardize on the names of the SPD_EEPROM_ADDRESS defines based on the
use case of the board.
We allow boards to override get_spd to either do board specific fixups
to the SPD data or deal with any unique behavior of how the SPD eeproms
are wired up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the include of mpc85xx/u-boot-nand.lds to utilize
CONFIG_SYS_LDSCRIPT rather than having an explicit config.mk
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Read MAC address from EEPROM. Add hwconfig settings.
Modified the default othbootargs to include the cache-sram-size
parameter. This parameter is needed as the L2 as SRAM is ON by
default in the P2020RDB kernel and used by the Gianfar driver.
Also cleanup some of the boot commands.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We enable SDHC_CD and SDHC_WP signals (pin muxed with GPIO8 & GPIO9
respectively).
We enable EXT2, FAT, and parition support for both MMC & USB configs.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on
P1022/P1013 SoCs.
Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the PCIe address map to match standard FSL memory map.
Additionally, fix the TLBs so the cover the PCIe address space properly
so cards plugged in like an e1000 work correctly.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If no Flash is connected to cs1, Linux crashes, because
reg entries are not correct adapted.
Following fix is needed:
- swap base addresses in CONFIG_SYS_FLASH_BANKS_LIST, as
flash bank 1 is on chipselect 0 and flash bank 2 on
chipselect 1
- call fdt_fixup_nor_flash_size() from ft_board_setup()
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
Currently, pixis_reset altbank does not work properly. This patch
uses the correct mask to boot into the alternate bank.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.
This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.
This patch is tested with compilation for armada100 and guruplug.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Mike Frysinger
Chong Huang
Andreas Schallenberg
Wolfgang Denk
Timur Tabi
Jerry Huang
Jiang Yutang
Zhao Chenhui
Poonam Aggrwal
Priyanka Jain
Haiying Wang
Kumar Gala
Li Yang
Daniel Schwierzeck
Tom Warren
Minkyu Kang
seedshope
Prabhakar Kushwaha
Heiko Schocher
Matthew McClintock
Lei Wen
Fabio Estevam
Graeme Russ