Reuse the gd->tbl value for timestamp and add gd->lastinc for lastinc bss
values in the OMAP timer driver.
The usage of bss values in drivers before initialisation of bss is forbidden.
In that special case some data in .rel.dyn gets corrupted.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: John Rigby <john.rigby@linaro.org>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This change allows the davinci timer functions to be used before
relocation since it avoids using static variables prior to BSS being
made available.
The code is based on that used in the at91 timers, modified to use
a davinci specific hardware timer. It also maintains reset_timer()
to allow deprecated timer usage to continue to work (for example,
in nand_base.c)
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
I doubt the stack_setup() was defective before:
we load the current location of _start and compare against destination
of relocate_code(). If we are already there we shoud skip the
relocation and jump over to clear_bss. Before the clear_bss was also skipped.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
r8 is used for global_data and should therefore be left alone!
For C code the compiler flag --fixed-r8 does the job, but in assembler
we need to be aware of that fact.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
In case we are still at relocation target address before relocation we
do not need to load the registers needed for relocation. We should
instead skip the whole relocation part and jump over to clear_bss
immediately.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
This patch uses r1 as scratch register for copy_loop(). Therefore we do
not longer need r7 for the storage of relocate_code()'s 'addr_moni' (the
destination address of relocation).
Therefore r7 can be used later on for other purposes.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
suggested from Daniel Hobi<daniel.hobi@schmid-telecom.ch>
Tested on following boards:
arm1136: qong
armv7: omap3_beagle
arm926ejs: magnesium, tx25
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
cc: Albert ARIBAUD <albert.aribaud@free.fr>
This patch fixes build errors in the vexpress system:
- Removed sys_proto.h requirement from syslib.c.
- Switched vexpress to the default armv7 linker script.
- Renamed TEXT_BASE to CONFIG_SYS_TEXT_BASE.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Reuse the gd->tbl value for timestamp and add gd->lastinc for lastinc
bss values in arm920t/at91/timer driver.
The usage of bss values in driver before initialisation of bss is
forbidden. In that special case some data in .rel.dyn gets corrupted by
the arm920t/at91/timer driver.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The AT91SAM9G20 BOOT ROM apparently initializes PA23 and PA24 to multi drive
(open drain). Revert this, if those pins are going to be used for MII.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Because of count_value is set to tcnb4 register,
should be get from this register when call udelay function.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With addition of "dram_init_banksize()" function from Heiko,Schocher
(commit ID: 561142af20), the DRAM size
is getting configured wrongly to 512Mb (CS0 & CS1).
So fix it to 256Mb.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The start.S file was only half-rewritten for ELF relocations.
This bugfix completes the rewrite.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
bulk addition of ELF relocation support to ARM cpus
arm946es, arm720t,arm920t, arm925t, arm_intcm, ixp,
lh7a40x, s3c44b0, and sa1100.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
The patch is to support getting FEC MAC address from fuse bank.
Signed-off-by: Jason Liu <r64343@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
DECLARE_GLOBAL_DATA_PTR is currently defined within the scope
of function while it is a global pointer. Change the scope of
definition to replicate it's global scope. This seems to help
gcc 4.5 optimizations as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
older ld emitted all ELF relocations in input sections named
.rel.dyn, whereas newer ld uses names of the form .rel*. The
linker script only collected .rel.dyn input sections. Rewrite
to collect all .rel* input sections.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
since commit 3667cbeed5
on beagle board the second sdram bank didn;t longer
work. Since this patch sdram settings just get copied
from bank a, but CMD_NOP, CMD_PRECHARGE, CMD_AUTOREFRESH
are not executed and after that mr register is also
not updated. This patch adds this for the bank b.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Steve Sakoman <steve@sakoman.com>
cc: Sandeep Paulraj <s-paulraj@ti.com>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().
With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway. So don't keep this relict any
longer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support. However, other recent changes led to a different
implementation (ELF relocation), where this no longer works. By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.
So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
If start of any DRAM bank is greater than total DDR size, remaining DDR banks' start address & size were left un-initialized in dram_init function. This could break other functions who uses array 'gd->bd->bi_dram'. Kirkwood network driver is one example. This also stops Linux kernel from booting.
v2 - Set start address also to 0. Without this Linux kernel couldn't
boot up
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
The patch removes the warning:
clock.c:291: warning: initialization from incompatible pointer type
after constification of args[]
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch fixes the reset command on imx25. The watchdog registers are 16
bits in size and not 32. This patch also adds the service register codes as
constants.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Remove u-boot.lds from mx5 and use the common u-boot.lds
of cpu layer. This patch also fix the building errors:
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_start'
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_end_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_end'
arch/arm/cpu/armv7/start.o: In function `_dynsym_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__dynsym_start'
Signed-off-by: Jason Liu <r64343@freescale.com>
This patch adds generic support for the Samsung s3c2440 processor.
Global s3c24x0 changes to struct members converting from upper case to
lower case.
Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
For the "fixloop" implementation in start.S a number of different
instructions was used. Unify code so all architectures use "blo"
here because it is more robust in case of incorrect alignments.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.aribaud@free.fr>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Fix relocation code for arm1176, do it like other ARM
CPU's are doing.
Tested only with CONFIG_SKIP_RELOCATE_UBOOT defined
and using nand_spl (booting from nand). Test done on
s3c6410 based board (not yet supported in main line).
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Fix address setup bug for ARM.
This bug stops u-boot booting if
CONFIG_SKIP_RELOCATE_UBOOT is defined.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Firstly, this fixes relocation issues. I had to use part of Dcache as RAM for a
while. I also moved around the lowlevel init code. It turned out so most of the
lowlevel init code ended in cpu.c (and eventually was rewritten into C).
This will also allow easier operation with FDT, multi-CPU-model support etc. in
later releases.
NOTE: This breaks most of the PXA boards (actually, the reloc stuff did already,
this only finishes the doom).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Conflicts:
arch/arm/include/asm/config.h
board/LaCie/edminiv2/config.mk
board/karo/tx25/config.mk
board/logicpd/imx27lite/config.mk
doc/README.arm-relocation
Signed-off-by: Wolfgang Denk <wd@denx.de>
clock.c / timer.c used static data and are called before relocation.
Move all static variables into global_data structure. Also cleanup
timer.c from unused stubs and make it truly use 64 bit tick values.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixes a typo in the routine to calculate the cs offset
based upon the contents of the SDRC cs_cfg register. This function
mistakenly shifts the CS1STARTLOW field 17 bits right instead of
17 bits left.
This hasn't been an issue to date because all OMAP3 boards currently
are configured to have zeros in this field.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
ELF relocation tables generated with linker option -pie can
be used to fixup code and data in a single loop at relocation,
removing the need for manual fixups anywhere else in the code.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
For all Kirkwood boards so far dram_init function is duplicated
dram_init function is moved to dram.c and relevant code from all
board specific files removed
If any board needs specific dram init handling than standard one,
then, a macro CONFIG_SYS_BOARD_DRAM_INIT should be defined in
board config header file and the dram_init function can be put
in board specific source file
For ex. keymile boards
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Earlier Device Identification register was used to detect
the type for SoC, considering 88F6282 support to be added,
It is not possible to detect the same using current
algorithm.
With this patch, device ID is being read using PCIE devid
register, also valid chip revision ID will also be read and
displayed
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Generalized misuse of ble within relocation and bss
initialization loops caused one iteration too many.
Instead of ble ('branch if lower or equal'), use
blo ('branch if lower').
While we're at it, fix all 'addreee' typos.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
When disabled the PIT runs until it reaches the CPIV value.
The Linux PIT driver stops the PIT and waits until it stopped. This can
take over 100ms. Simply stopping in u-boot isn't sufficient as the PIT
will still be running when Linux is waiting until it stopped.
So, we stop it in u-boot by setting the compare value to a value slightly
greater than the current running counter to make the PIT stopped in short
time.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
The OMAP3 cpu directory contains a syslib file with some utilities
that can be shared by all targets using arm cortexa8 processors,
not only OMAP.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Calculate the SDRAM size from DMM configuration registers instead of using
hard-coded values. This gives correct values for all different boards.
It's assumed that DMM sections do not overlap memory areas.
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Change the implementation for arm1176 to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for arm720t to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for arm_intcm to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for lh7a40x to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for s3c44b0 to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for sa1100 to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for ixp to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for pxa to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for arm946 to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for arm925 to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for arm920 to relocate the code to
an arbitrary address in RAM.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for arm926 to relocate the code to
an arbitrary address in RAM.
Adapt the TX25 (i.MX25), magnesium board to test the changes.
On the tx25 board TEXT_BASE is set to the final relocation
address to prevent one more copying of u-boot code
when relocating. More info see:
doc/README.arm-relocation
da850 board:
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Change the implementation for ARM V7 to relocate the code to an
arbitrary address in RAM.
Adapt the Beagle board (Cortex A8) to test the changes.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Change the implementation for ARM11 to relocate the code to an
arbitrary address in RAM.
Tested on the qong board.
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add data cache support for arm1136 systems.
Enable "cache" command on Qong board and test performance.
Test 1: Loading 127 MB of data from NAND flash into RAM:
Instr. Cache off on on
Data Cache off off on
--------------------------------------------------
QONG (ARM11) 177s 95s 43s = x 4.1
Test 2: uncompressing a gzipped image from RAM to RAM
(size compressed: 6.5 MiB, uncompressed: 35 MiB):
Instr. Cache off on on
Data Cache off off on
--------------------------------------------------
QONG (ARM11) 1.54s 0.95s 0.18s = x 8.6
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add data cache support for ARM V7 systems. Used cache flush
functions from linux:arch/arm/mm/cache-v7.S developed from
Catalin Marinas.
Enable "cache" command on Beagle board and test performance.
Test 1: Loading 127 MB of data from NAND flash into RAM:
Instr. Cache off on on
Data Cache off off on
--------------------------------------------------
Beagle (Cortex A8) 116s 106s 30.3s = x 3.8
Test 2: uncompressing a gzipped image from RAM to RAM
(size compressed: 6.5 MiB, uncompressed: 35 MiB):
Instr. Cache off on on
Data Cache off off on
--------------------------------------------------
Beagle (Cortex A8) 1.84s 1.64s 0.12s = x 15.3
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Ben Gardiner<bengardiner@nanometrics.ca>
Upcoming Beagle and Overo revisions use POP memory with 256MB or 512MB
per bank. This patches uses the SDRC settings from x-load or the config
header to set up timing properly.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Using the reset command on OMAP36XX/37XX and OMAP4 caused a hang. This
patch uses the reset bit appropriate for each CPU architecture.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The workarounds for errata 621766 and 725233 should only be applied
on affected Cortex-A8 revisions. Recent chips use r3px cores where
these have been fixed.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This function consists entirely of inline asm statements, so writing
it directly in a .S file is simpler. Additionally, the inline asm is
not safe as is, since registers are not guaranteed to be preserved
between asm() statements.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
On OMAP34xx ES1.0, the L2 enable bit can only be set in secure mode,
so an SMC call to the ROM monitor is required. On later versions,
and on newer devices, this bit is banked and we can set it directly.
The code checked only the ES revision of the chip, and hence incorrectly
used the ROM call on ES1.0 versions of other devices.
This patch adds a check for chip family as well as revision, and also
removes some code duplication between the enable and disable functions.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch configures clocks properly when a 36XX/37XX
processor is detected.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TI has added new processors to the OMAP3 family. This patch enhances
the code in sysinfo.c to detect which family member is present.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The functions in syslib.c can be shared, so this patch moves it from
cpu/omap3 to cpu/omap-common
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Fix: return value of get_tbclk
* this fixes issue with prematurely restart/retry, if BOOT_RETRY_TIMEOUT is used
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Because of peripheral devices can select clock sources,
separate the peripheral clocks. (pwm, uart and so on)
It just return the pclk at s5pc1xx SoC,
but s5pc210 SoC must be calculated by own clock register setting.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fixed kw_winctrl_calcsize() off-by-1 bug which caused mapping
windows size to be cut by half.
This corrected all windows address configuration
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Fix orion5x_winctrl_calcsize() off-by-1 bug which caused mapping
windows to be cut by half. This afected all windows including NOR
flash (causing half the flash to be unaccessible) but DRAM was and
still is fine as its size is determined otherwise.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Because of these are common files around s5p Socs, rename from s5pc1xx to s5p.
And getting cpu_id is SoC specific, so move to SoC's header file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds basic support for s5pc210.
s5p-common will be used by all of s5p SoCs.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch is intended to prepare the other S5P SoC. (s5pc210)
If use SoC specific defines then can't share with other SoC.
So, make the accessor functions for access the base address by common way.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Turn all ORION5X_DEF{ADR,SZ}_xxx macros into ORION5X_{ADR,SZ}_xxx
and allow defining them from board code to override defaults. This
is particularly useful for defining board-specific FLASH address
and size in board header file rather than having to tweak orion5x
code.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
get_timer_masked() should return current timestamp,
not current ticks from hardware register.
Tested on one custom board with NAND flash.
Without this patch, NAND write always TIMEOUT
because get_timer(0) return a big value.
This patch applies for u-boot-2010.06
Signed-off-by: Li Haibo <hbli@sinocastel.com>
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The OMAP4 x-load code sets gptimer1 clock source to 32Khz. This isn't
acceptable for udelay. This patch changes from gptimer1 to gptimer2,
which uses sys_clk at 38.4 Mhz.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add functional multiplexing support for OMAP4 pads.
Configure all the pads for the OMAP4430 SDP
and OMAP4 Panda boards
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds a gpmc_init function for OMAP4 and adds calls to
gpmc_init for existing OMAP4 boards: panda and sdp4430
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add definitions and initialization in orion5x for mvgbe.
Add orion5x in mvgbe SoC includes.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rename all references to kirkwood in mvgbe symbols
throughout the whole codebase.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds minimum support for OMAP4. Code which can be shared
between OMAP3 and OMAP4 is placed in arch/arm/cpu/armv7/omap-common
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9
Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.
The two architectures are similar enough that substantial code can be shared.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The ARM ABI requires that the stack be aligned to 8 bytes as it is noted
in Procedure Call Standard for the ARM Architecture:
http://infocenter.arm.com/help/topic/com.arm.doc.ihi0042d/index.html
Unaligned SP also causes the problem with variable-length arrays
allocation when VLA address becomes less than stack pointer during
aligning of this address, so the next 'push' in the stack overwrites
first 4 bytes of VLA.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Tested on tx25(mx25), imx27lite(mx27), qong(mx31) and trab(s3c2400)
Tested-by: Wolfgang Denk <wd@denx.de>
The push / pop instructions used in this file are available only with
more recent tool chains:
cache.S: Assembler messages:
cache.S:133: Error: bad instruction `push {r0,r1,r2,lr}'
cache.S:160: Error: bad instruction `pop {r1,r2,r3,pc}'
cache.S:164: Error: bad instruction `push {r0,r1,r2,lr}'
cache.S:191: Error: bad instruction `pop {r1,r2,r3,pc}'
Change push/pop into stmfd/ldmfd instructions to support older
versions of binutils as well.
I verified that the modified source code generates exactly the same
binary code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rix <tom@bumblecow.com>
This patch adds support for the Marvell Orion5x SoC.
It has no use alone, and must be followed by a patch
to add Orion5x support for serial, then support for
the ED Mini V2, an Orion5x-based product from LaCie.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Part of this patch is by: Mikhail Kshevetskiy.
Stack must be aligned to 8 bytes on PXA (possibly all armv5te) for LDRD/STRD
instructions. In case LDRD/STRD is issued on an unaligned address, the behaviour
is undefined.
The issue was observed when working with the NAND code, which was rendered
disfunctional. Also, the vsprintf() function had serious problems with printing
64bit wide long longs. After aligning the stack, this wrong behaviour is no
longer present.
Tested on:
Marvell Littleton PXA310 board
Toradex Colibri PXA320 board
Aeronix Zipit Z2 PXA270 handheld
Voipac PXA270 board
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Wolfgang Denk
Nishanth Menon
Dirk Behme
Nick Thompson
Andreas Bießmann
Heiko Schocher
Matt Waddel
Andreas Bießmann
Reinhard Meyer
Minkyu Kang
Vaibhav Hiremath
Albert Aribaud
Liu Hui-R64343
Sebastien Carlier
Tanmay Upadhyay
Stefano Babic
Matthias Weisser
C Nauman
Mikhail Kshevetskiy
Darius Augulis
Gray Remlin
Marek Vasut
Steve Sakoman
Prafulla Wadaskar
Albert Aribaud
Prafulla Wadaskar
Alexander Stein
Aneesh V
Thomas Weber
Mans Rullgard
Jens Scharsig
Li Haibo
Mike Frysinger
Vitaly Kuzmichev